| 1. |
- Kirschner, Andreas, et al.
(författare)
-
Modelling of deposition and erosion of injected WF6 and MoF6 in TEXTOR
- 2016
-
Ingår i: Nuclear Materials and Energy. - : Elsevier. - 2352-1791.
-
Tidskriftsartikel (refereegranskat)abstract
- Tracer injection experiments in TEXTOR with MoF 6 and WF 6 lead to local deposition of about 6% for Mo and about 1% for W relative to the injected amount of Mo and W atoms. Modelling of these experiments has been done with ERO applying updated data for physical sputtering. The dissociation of the injected molecules has been treated in a simplified manner due to the lack of dissociation rate coefficients. How- ever, with this it was possible to reproduce the observed radial penetration of Mo and W atoms into the plasma. The modelled local deposition efficiencies are about 50% for Mo and 60% for W assuming typical plasma parameters for the experimental conditions used. To reproduce the measured deposition efficien- cies an enhancement factor for the erosion of deposited Mo and W has to be assumed ( ∼10 for Mo and ∼25 for W). Due to the rather low electron temperature T e of these plasma conditions (T e ∼15 eV at the location of injection), Mo and W are mostly sputtered by impurities whereas sputtering due to deuterium is negligible. A parameter study applying larger electron temperature leads to increased sputtering and thus to reduced local deposition efficiencies of about 30% for Mo and 5% for W. Though, even under these conditions enhanced erosion, albeit with reduced enhancement factors, is needed in the modelling to obtain the small measured deposition efficiencies.
|
|
| 2. |
- Rubel, Marek J., et al.
(författare)
-
Nitrogen and Neon Retention in Plasma-Facing Materials
- 2011
-
Ingår i: Journal of Nuclear Materials. - : Elsevier. - 0022-3115 .- 1873-4820. ; 415:1, s. S223-S226
-
Tidskriftsartikel (refereegranskat)abstract
- Tungsten plate was exposed in the TEXTOR tokamak during nitrogen-assisted discharges. In order to determine material mixing on tungsten, the plate was examined ex situ with ion beam analysis techniques including time-of-flight heavy ion elastic recoil detection analysis and also with X-ray photoelectron spectroscopy. Nitrogen content in the range from 1.3 × 1015 to 3.4 × 1015 cm−2 is measured in the outermost surface layer (20 nm) of the W plate. Photoelectron spectroscopy detects nitrogen both in the elemental and compound form, i.e. tungsten nitride (WN/W2N). Nitrogen is measured even in hot areas free from deuterium. Also neon co-implantation into the plasma-facing components has been identified following Ne-cooled pulses.
|
|
| 3. |
- Weckmann, Armin, et al.
(författare)
-
Global material migration in tokamaks : patterns, material balance and transport mechanisms in TEXTOR
- 2017
-
Annan publikation (övrigt vetenskapligt/konstnärligt)abstract
- As the last experiment before the final shutdown of the TEXTOR tokamak, equipped with all-graphite plasma-facing components (PFCs), MoF6 had been injected into the vacuum vessel. During decommissioning all PFCs became available for surface studies, enabling detailed mapping of previously injected Mo, W and intrinsic 625 Inconel metals. As a result, detailed deposition patterns for these metals were obtained, revealing a number of findings: a) High-Z metals are mainly globally deposited, with concentrations decaying exponentially with distance from the injection source; b) the decay length is of the order of 0.1 m on the main PFC and 1.0 m on the receded PFC; c) ion flow velocities co-decide the position of maximum deposition. Modelling with ERO shows exponential decay. Simulated decay lengths are between 0.15 – 1.30 m, depending on the anomalous cross field diffusion coefficient. Extensive measurements of Mo have been undertaken in order to quantify the amounts deposited on the graphite PFCs, showing that the ratio of local to global deposited high-Z metals is 0.3-0.4. However, only up to 20% of the injected Mo could be detected on all the PFCs. A large fraction of injected Mo may have been pumped out before being deposited. The bumper limiter is found to be the major repository for all probed elements. For W and F, this is solely due to the limiter size – the areal concentration is not enhanced. For Mo, Inconel metals, 15N and D the areal concentration on the bumper limiter is higher than on the toroidal belt limiter ALTII acting as main PFC.
|
|
