| 1. |
- Akintunde, Moyinoluwa, et al.
(författare)
-
Bacterial Cellulose Production from agricultural Residues by two Komagataeibacter sp. Strains
- 2022
-
Ingår i: Bioengineered. - : Informa UK Limited. - 2165-5979 .- 2165-5987. ; 13:4, s. 10010-10025
-
Tidskriftsartikel (refereegranskat)abstract
- Agricultural residues are constantly increasing with increased farming processes, and improper disposal is detrimental to the environment. Majority of these waste residues are rich in lignocellulose, which makes them suitable substrate for bacterial fermentation in the production of valueadded products. In this study, bacterial cellulose (BC), a purer and better form of cellulose, was produced by two Komagataeibacter sp. isolated from rotten banana and kombucha drink using corncob (CC) and sugarcane bagasse (SCB) enzymatic hydrolyzate, under different fermentation conditions, that is, static, continuous, and intermittent agitation. The physicochemical and mechanical properties of the BC films were then investigated by Fourier Transformed Infrared Spectroscopy (FTIR), Thermogravimetry analysis, Field Emission Scanning Electron Microscopy (FESEM), and Dynamic mechanical analysis. Agitation gave a higher BC yield, with Komagataeibacter sp. CCUG73629 producing BC from CC with a dry weight of 1.6 g/L and 1.4 g/L under continuous and intermittent agitation, respectively, compared with that of 0.9 g/L in HS medium. While BC yield of dry weight up to 1.2 g/L was obtained from SCB by Komagataeibacter sp. CCUG73630 under continuous agitation compared to that of 0.3 g/L in HS medium. FTIR analysis showed BC bands associated with cellulose I, with high thermal stability. The FE-SEM analysis showed that BC fibers were highly ordered and densely packed. Although the BC produced by both strains showed similar physicochemical and morphological properties, the BC produced by the Komagataeibacter sp. CCUG73630 in CC under intermittent agitation had the best modulus of elasticity, 10.8 GPa and tensile strength, 70.9 MPa. [GRAPHICS]
|
|
| 2. |
- Bahrami, Bahador, et al.
(författare)
-
Incorporation of Extracted Mucor indicus Fungus Chitin Nanofibers into Starch Biopolymer: Morphological, Physical, and Mechanical Evaluation
- 2021
-
Ingår i: Starch. - : John Wiley & Sons. - 0038-9056. ; 73:7-8
-
Tidskriftsartikel (refereegranskat)abstract
- Bio-nanocomposites based on starch are reinforced by different percentages of chitin nanofibers (ChNFs) and compatibilized by glycerol. Nanofibers are extracted from Mucor indicus fungus through different chemo-mechanical pretreatments. The mechnical, chemo-physical, and morphological properties of the nanocomposite starch films were evaluated and compared with the unfilled thermoplastic starch (TPS) film. Based on the obtained results, Young's modulus of the film at 5 wt.% ChNFs indicated 239% enhancement compared to the TPS film due to the existence of good interactions between starch and ChNFs. Moreover, the ultimate strength of the reinforced film at 5 wt.% ChNFs and the unreinforced counterpart are found to be 5.5 and 1.74 MPa, indicating 216% improvement; however, the elongation at break of the films decreases from 59.3% to 19.3% by adding 5 wt.% ChNFs. In addition, the moisture absorption of the film decreases after the incorporation of ChNFs. Based on the morphological study, ChNFs increase the roughness of the starch matrix with a homogenous morphology revealing the good dispersion of nanofibers in the TPS film. Finally, the nanocomposite film with 5 wt.% ChNFs show the best properties to employ for bio-film applications.
|
|
| 3. |
- Bátori, Veronika, 1980-, et al.
(författare)
-
Anaerobic degradation of bioplastics: A review
- 2018
-
Ingår i: Waste Management. - : Elsevier BV. - 0956-053X. ; 80, s. 406-413
-
Tidskriftsartikel (refereegranskat)abstract
- Anaerobic digestion (AD) of the organic fraction of municipal solid waste (OFMSW), leading to renewableenergy production in the form of methane, is a preferable method for dealing with the increasing amountof waste. Food waste is separated at the source in many countries for anaerobic digestion. However, thepresence of plastic bags is a major challenge for such processes. This study investigated the anaerobicdegradability of different bioplastics, aiming at potential use as collecting bags for the OFMSW. Thechemical composition of the bioplastics and the microbial community structure in the AD processaffected the biodegradation of the bioplastics. Some biopolymers can be degraded at hydraulic retentiontimes usually applied at the biogas plants, such as poly(hydroxyalkanoate)s, starch, cellulose and pectin,so no possible contamination would occur. In the future, updated standardization of collecting bags forthe OFMSW will be required to meet the requirements of effective operation of a biogas plant.
|
|
| 4. |
|
|
| 5. |
- Bátori, Veronika, 1980-, et al.
(författare)
-
Pectin-based Composites
- 2017
-
Ingår i: Handbook of Composites from Renewable Materials. - : John Wiley & Sons. - 9781119223795 ; , s. 487-518
-
Bokkapitel (övrigt vetenskapligt/konstnärligt)abstract
- One third of the cell wall of vascular plants is composed of pectin, which serves as the cementing material for the cellulosic network, behaving as a stabilized gel. Industrially, pectin is produced from juice and sugar production waste. Different sources and extraction conditions result in diversity in characteristics and applications of pectin. Most commonly, pectin is used in the food industry as a gelling and thickening agent and it is favored in the pharmaceutical industry as a carrier for colon-specific drugs. Pectin has good potential to be utilized as a matrix in production of environmentally friendly film packaging as well as biocomposite materials. Pectin is sensitive to chemical reactions and promotes the homogeneous immobilization of cells, genes, and proteins. However, due to limited mechanical properties pectin is not used for structural applications but instead rather for composites in which its biodegradable properties can be utilized. Pectin is often reinforced with hydroxyapatite and biphasic calcium phosphate for bone regeneration and tissue engineering applications. It can also be used as a biosorbent for copper removal from aqueous solutions. Active packaging of nanohybrids composed of pectin and halloysite nanotubes that are loaded with rosemary essential oil is another application of pectin-based composites.
|
|
| 6. |
- Bátori, Veronika, 1980-, et al.
(författare)
-
Production of Pectin-Cellulose Biofilms: A New Approach for Citrus Waste Recycling
- 2017
-
Ingår i: International Journal of Polymer Science. - : Hindawi Limited. - 1687-9422 .- 1687-9430. ; 2017, s. 1-9
-
Tidskriftsartikel (refereegranskat)abstract
- While citrus waste is abundantly generated, the disposal methods used today remain unsatisfactory: they can be deleterious for ruminants, can cause soil salinity, or are not economically feasible; yet citrus waste consists of various valuable polymers. This paper introduces a novel environmentally safe approach that utilizes citrus waste polymers as a biobased and biodegradable film, for example, for food packaging. Orange waste has been investigated for biofilm production, using the gelling ability of pectin and the strength of cellulosic fibres. A casting method was used to form a film from the previously washed, dried, and milled orange waste. Two film-drying methods, a laboratory oven and an incubator shaker, were compared. FE-SEM images confirmed a smoother film morphology when the incubator shaker was used for drying. The tensile strength of the films was 31.67 ± 4.21 and 34.76 ± 2.64 MPa, respectively, for the oven-dried and incubator-dried films, which is within the range of different commodity plastics. Additionally, biodegradability of the films was confirmed under anaerobic conditions. Films showed an opaque appearance with yellowish colour.
|
|
| 7. |
- Bátori, Veronika, 1980-, et al.
(författare)
-
Synthesis and characterization of maleic anhydride-grafted orange waste for potential use in biocomposites
- 2018
-
Ingår i: BioResources. - : BioResources. - 1930-2126. ; 13:3, s. 4986-4997
-
Tidskriftsartikel (refereegranskat)abstract
- The purpose of the study was to develop a less hydrophilic, and therefore more useful, material from orange waste produced in large quantities by the food industry. A new derivative of industrial orange waste was synthesized via esterification with maleic anhydride. The reaction was confirmed via Fourier transform infrared spectroscopy (FTIR), and the degree of substitution of the hydroxyl groups was 0.39 ± 0.01, as determined by a back-titration method. A major change in physical structure was confirmed by scanning electron microscopy (SEM). The flake-like structure of orange waste changed to a sponge-like structure after the reaction, which involved an increased volume and a reduced density by approximately 40%. The sponge-like structure was represented as an agglomeration of particles with a low specific surface area of 2.18 m2/g and a mean pore diameter of 10.7 nm. Interestingly, the grafted orange waste seemed to become more hydrophobic, which was confirmed by a contact angle test; however, the material absorbed more water vapor. Thermogravimetric analysis (TGA) confirmed a thermally more uniform, though, less heat-resistant material. This work suggests a possible way of utilizing orange waste via synthesizing a renewable material with possible applications as a filler in biocomposites.
|
|
| 8. |
- Bátori, Veronika, 1980-, et al.
(författare)
-
The effect of glycerol, sugar and maleic anhydride on pectin-cellulose biofilms prepared from orange waste
- 2019
-
Ingår i: Polymers. - : MDPI AG. - 2073-4360.
-
Tidskriftsartikel (refereegranskat)abstract
- This study was conducted to improve the properties of thin films prepared from orange waste by the solution casting method. The main focus was the elimination of holes in the film structure by establishing better cohesion between the major cellulosic and pectin fractions. For this, a previously developed method was improved first by the addition of sugar to promote pectin gelling, then by the addition of maleic anhydride. Principally, maleic anhydride was introduced to the films to induce cross-linking within the film structure. The effects of concentrations of sugar and glycerol as plasticizers and maleic anhydride as a cross-linking agent on the film characteristics were studied. Maleic anhydride improved the structure, resulting in a uniform film, and morphology studies showed better adhesion between components. However, it did not act as a cross-linking agent, but rather as a compatibilizer. The middle level (0.78%) of maleic anhydride content resulted in the highest tensile strength (26.65 ± 3.20 MPa) at low (7%) glycerol and high (14%) sugar levels and the highest elongation (28.48% ± 4.34%) at high sugar and glycerol levels. To achieve a uniform film surface with no holes present, only the lowest (0.39%) level of maleic anhydride was necessary.
|
|
| 9. |
- Bidgoli, Hossein, et al.
(författare)
-
Effect of carboxymethylation conditions on water binding capacity of chitosan-based superabsorbents
- 2010
-
Ingår i: Carbohydrate Research. - : Elsevier - Pergamon. - 0008-6215 .- 1873-426X. ; 345:18, s. 2683-2689
-
Tidskriftsartikel (refereegranskat)abstract
- A superabsorbent polymer (SAP) from chitosan was provided via carboxymethylation of chitosan, followed by cross-linking with glutaraldehyde and freeze-drying. This work was focused on an investigation of the effects of monochloroacetic acid (MCAA), sodium hydroxide, and reaction time on preparation of carboxymethylchitosan (CMCS). The CMCS products were characterized using FTIR spectroscopy, and their degrees of substitution (DS) were measured using conductimetry and FTIR analysis. The highest DS value was obtained when the carboxymethylation reaction was carried out using 1.75 g MCAA and 1.75 g NaOH per g of chitosan in 4 h. The water solubilities of the CMCS products at various pHs were also evaluated, and the results indicated a significant impact of the reaction parameters on the solubility of CMCS. The CMCSs with the highest DS value resulted in SAPs having the highest water-binding capacity (WBC). TheWBCof the best SAP measured after 10 minexposure in distilled water, 0.9% NaCl solution, synthetic urine, and artificial blood was 104, 33, 30, and 57 g/g, respectively. The WBC of this SAP at pH 2–9 passed a maximum at pH 6.
|
|
| 10. |
- Dumitrescu, Delia, et al.
(författare)
-
Orange Waste Films as a Raw Material for Designing Bio-Based Textiles : A Hybrid Research Method
- 2022
-
Ingår i: Materials Science Forum. - Switzerland : Trans Tech Publications, Ltd.. - 0255-5476 .- 1662-9752. ; 1063, s. 3-14
-
Tidskriftsartikel (refereegranskat)abstract
- Bio-based textiles are an emerging area of cross-disciplinary research, involving material science and design and contributing to textile sustainability. An example of a bio-based textile is an orange-waste film, which is plant-based and biodegradable and possesses mechanical properties which are comparable to some commodity plastics. The research project presented in this article aimed to explore orange-waste film as a new material for textile and fashion design and highlights how experimental co-design processes and innovation involving orange waste film as a textile material adds a new layer of material understanding to both textile design and technology-driven material research. Material-development methods were used to develop the orange-waste film, as were textile design methods with a focus on surface design. The results show that material variables such as tensile strength and elongation are dependent on the grinding process and drying temperature used for the raw material, as these determined the quality and durability of the orange-waste film and its applicability to the field of textile design. The use of orange waste in the creation of textiles opens up more ways of thinking about and working with materials, and orange waste could become a desirable raw material for textile design on the basis that it introduces certain aesthetic and functional possibilities through its visual and tactile expression and material behaviour, in addition to defining methods of producing textiles.
|
|
| 11. |
- Furgier, Valentin, et al.
(författare)
-
Development and Characterisation of Composites Prepared from PHBV Compounded with Organic Waste Reinforcements, and Their Soil Biodegradation
- 2024
-
Ingår i: Materials. - 1996-1944. ; 17:3
-
Tidskriftsartikel (refereegranskat)abstract
- Poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) is a biobased and biodegradable polymer. This polymer is considered promising, but it is also rather expensive. The objective of this study was to compound PHBV with three different organic fillers considered waste: human hair waste (HHW), sawdust (SD) and chitin from shrimp shells. Thus, the cost of the biopolymer is reduced, and, at the same time, waste materials are valorised into something useful. The composites prepared were characterised by differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), tensile strength and scanning electron micrograph (SEM). Tests showed that chitin and HHW did not have a reinforcing effect on tensile strength while the SD increased the tensile strength at break to a certain degree. The biodegradation of the different composites was evaluated by a soil burial test for five months. The gravimetric test showed that neat PHBV was moderately degraded (about 5% weight loss) while reinforcing the polymer with organic waste clearly improved the biodegradation. The strongest biodegradation was achieved when the biopolymer was compounded with HHW (35% weight loss). The strong biodegradation of HHW was further demonstrated by characterisation by Fourier-transform infrared spectroscopy (FTIR) and solid-state nuclear magnetic resonance (NMR). Characterisation by SEM showed that the surfaces of the biodegraded samples were eroded.
|
|
| 12. |
- Gomes Hastenreiter, Lara Lopes, et al.
(författare)
-
Synthesis of Lactic Acid-Based Thermosetting Resins and Their Ageing and Biodegradability
- 2020
-
Ingår i: Polymers. - : MDPI AG. - 2073-4360. ; :12, s. 1-17
-
Tidskriftsartikel (refereegranskat)abstract
- The present work is focused on the synthesis of bio-based thermoset polymers and their thermo–oxidative ageing and biodegradability. Toward this aim, bio-based thermoset resins with different chemical architectures were synthesized from lactic acid by direct condensation with ethylene glycol, glycerol and pentaerythritol. The resulting branched molecules with chain lengths (n) of three were then end-functionalized with methacrylic anhydride. The chemical structures of the synthesized lactic acid derivatives were confirmed by proton nuclear magnetic resonance spectroscopy (1H-NMR) and Fourier transform infrared spectroscopy (FT–IR) before curing. To evaluate the effects of structure on their properties, the samples were investigated by differential scanning calorimetry (DSC), thermogravimetric analysis (TGA) and the tensile testing. The samples went through thermo-oxidative ageing and biodegradation; and their effects were investigated. FT-IR and 1H-NMR results showed that three different bio-based resins were synthesized using polycondensation and end-functionalization. Lactic acid derivatives showed great potential to be used as matrixes in polymer composites. The glass transition temperature of the cured resins ranged between 44 and 52 °C. Pentaerythritol/lactic acid cured resin had the highest tensile modulus and it was the most thermally stable among all three resins. Degradative processes during ageing of the samples lead to the changes in chemical structures and the variations in Young’s modulus. Microscopic images showed the macro-scale surface degradation on a soil burial test.
|
|
| 13. |
- Gurram, Rajesh, et al.
(författare)
-
A solvent-free approach for production of films from pectin and fungal biomass
- 2018
-
Ingår i: Journal of Polymers and the Environment. - : Springer Science and Business Media LLC. - 1566-2543 .- 1572-8919. ; 26:11, s. 4282-4292
-
Tidskriftsartikel (refereegranskat)abstract
- Self-binding ability of the pectin molecules was used to produce pectin films using the compression molding technique, as an alternative method to the high energy-demanding and solvent-using casting technique. Moreover, incorporation of fungal biomass and its effects on the properties of the films was studied. Pectin powder plasticized with 30% glycerol was subjected to heat compression molding (120 °C, 1.33 MPa, 10 min) yielding pectin films with tensile strength and elongation at break of 15.7 MPa and 5.5%, respectively. The filamentous fungus Rhizopus oryzae was cultivated using the water-soluble nutrients obtained from citrus waste and yielded a biomass containing 31% proteins and 20% lipids. Comparatively, the same strain was cultivated in a semi-synthetic medium resulting in a biomass with higher protein (60%) and lower lipid content (10%). SEM images showed addition of biomass yielded films with less debris compared to the pectin films. Incorporation of the low protein content biomass up to 15% did not significantly reduce the mechanical strength of the pectin films. In contrast, addition of protein-rich biomass (up to 20%) enhanced the tensile strength of the films (16.1–19.3 MPa). Lastly, the fungal biomass reduced the water vapor permeability of the pectin films.
|
|
| 14. |
- Gustafsson, Jesper, et al.
(författare)
-
Development of Bio-Based Films and 3D Objects from Apple Pomace
- 2019
-
Ingår i: Polymers. - : MDPI AG. - 2073-4360. ; 11:2
-
Tidskriftsartikel (refereegranskat)abstract
- Extensive quantities of apple pomace are generated annually but its disposal is still challenging. This study addresses this issue by introducing a new, environmentally-friendly approach for the production of sustainable biomaterials from apple pomace, containing 55.47% free sugars and a water insoluble fraction, containing 29.42 ± 0.44% hemicelluloses, 38.99 ± 0.42% cellulose, and 22.94 ± 0.12% lignin. Solution casting and compression molding were applied to form bio-based films and 3D objects (i.e., fiberboards), respectively. Using glycerol as plasticizer resulted in highly compact films with high tensile strength and low elongation (16.49 ± 2.54 MPa and 10.78 ± 3.19%, respectively). In contrast, naturally occurring sugars in the apple pomace showed stronger plasticizing effect in the films and resulted in a fluffier and connected structure with significantly higher elongation (37.39 ± 10.38% and 55.41 ± 5.38%, respectively). Benefiting from the self-binding capacity of polysaccharides, fiberboards were prepared by compression molding at 100 °C using glycerol or naturally occurring sugars, such as plasticizer. The obtained fiberboards exhibited tensile strength of 3.02–5.79 MPa and elongation of 0.93%–1.56%. Possible applications for apple pomace biomaterials are edible/disposable tableware or food packaging.
|
|
| 15. |
|
|
| 16. |
- Karimi-Avargani, Mina, et al.
(författare)
-
The promiscuous potential of cellulase in degradation of polylactic acid and its jute composite
- 2021
-
Ingår i: Chemosphere. - : Elsevier. - 0045-6535 .- 1879-1298. ; 278
-
Tidskriftsartikel (refereegranskat)abstract
- It has been suggested that cellulolytic enzymes can be effective on the degradation of PLA samples. The idea was investigated by examining the impact of cellulase on degradation of PLA and PLA-jute (64/36) composite in an aqueous medium. The obtained results demonstrated 55% and 61% thickness reduction in PLA and PLA-jute specimens after four months of treatment, respectively. Gel permeation chromatography (GPC) showed significant decline in the number average molecular weight (Mn) approximately equal to 85% and 80% for PLA and PLA-jute in comparison with their control. The poly dispersity index (PDI) of PLA and PLA-jute declined 41% and 49% that disclosed more homogenous distribution in molecular weight of the polymer after treatment with cellulase. The cellulase promiscuity effect on PLA degradation was further revealed by Fourier-transform infrared spectroscopy (FT-IR) analysis where substantial decrease in the peak intensities of the polymer related functional groups were observed. In addition, PLA biodegradation was studied in more detail by differential scanning calorimetry (DSC) and thermal gravimetric analysis (TGA) of control and cellulase treated specimens. The obtained results confirmed the promiscuous function of cellulase in the presence or the absence of jute as the specific substrate of cellulase. This can be considered as a major breakthrough to develop effective biodegradation processes for PLA products at the end of their life cycle.
|
|
| 17. |
- Karimi-Avargani, Mina, et al.
(författare)
-
The special effect of the Aspergillus flavus and its enzymes on biological degradation of the intact polylactic acid (PLA) and PLA-Jute composite
- 2020
-
Ingår i: Polymer degradation and stability. - : Elsevier. - 0141-3910 .- 1873-2321. ; 179
-
Tidskriftsartikel (refereegranskat)abstract
- The biodegradation of PLA and PLA-Jute (64/36) in an aqueous media with Aspergillus flavus CCUG 28296, as well as its cell-free enzyme extract, was investigated through their physical, molecular, and thermal characterization. Results indicated that the thicknesses of the fungal treated PLA and PLA-jute samples during seven months have reduced by 52% and 63%, respectively while for the enzyme-treated samples, 45% and 49% reduction in the thickness has occurred. Moreover, the gel permeation chromatography (GPC) revealed a substantial decrease (about 75%) in the weight average molecular weight (Mw) of PLA and PLA-Jute treated with fungus, which confirmed the effective performance of A. flavus on the biological degradation of PLA. The obtained results were further supported by differential scanning calorimetry (DSC) and thermal gravimetric analysis (TGA) of the treated and control samples as well. Interestingly, the observed reduction in the Mw of PLA in PLA-Jute was 64% after the enzymatic treatment, while for the unblended PLA, it was just about 32%. These results pointed to the synergistic effect of jute on PLA degradation because of the promiscuous activity of the effective enzymes on jute degradation, which could accelerate the PLA decomposition.
|
|
| 18. |
- Lozano, Rafael, et al.
(författare)
-
Measuring progress from 1990 to 2017 and projecting attainment to 2030 of the health-related Sustainable Development Goals for 195 countries and territories: a systematic analysis for the Global Burden of Disease Study 2017
- 2018
-
Ingår i: The Lancet. - : Elsevier. - 1474-547X .- 0140-6736. ; 392:10159, s. 2091-2138
-
Tidskriftsartikel (refereegranskat)abstract
- Background: Efforts to establish the 2015 baseline and monitor early implementation of the UN Sustainable Development Goals (SDGs) highlight both great potential for and threats to improving health by 2030. To fully deliver on the SDG aim of “leaving no one behind”, it is increasingly important to examine the health-related SDGs beyond national-level estimates. As part of the Global Burden of Diseases, Injuries, and Risk Factors Study 2017 (GBD 2017), we measured progress on 41 of 52 health-related SDG indicators and estimated the health-related SDG index for 195 countries and territories for the period 1990–2017, projected indicators to 2030, and analysed global attainment. Methods: We measured progress on 41 health-related SDG indicators from 1990 to 2017, an increase of four indicators since GBD 2016 (new indicators were health worker density, sexual violence by non-intimate partners, population census status, and prevalence of physical and sexual violence [reported separately]). We also improved the measurement of several previously reported indicators. We constructed national-level estimates and, for a subset of health-related SDGs, examined indicator-level differences by sex and Socio-demographic Index (SDI) quintile. We also did subnational assessments of performance for selected countries. To construct the health-related SDG index, we transformed the value for each indicator on a scale of 0–100, with 0 as the 2·5th percentile and 100 as the 97·5th percentile of 1000 draws calculated from 1990 to 2030, and took the geometric mean of the scaled indicators by target. To generate projections through 2030, we used a forecasting framework that drew estimates from the broader GBD study and used weighted averages of indicator-specific and country-specific annualised rates of change from 1990 to 2017 to inform future estimates. We assessed attainment of indicators with defined targets in two ways: first, using mean values projected for 2030, and then using the probability of attainment in 2030 calculated from 1000 draws. We also did a global attainment analysis of the feasibility of attaining SDG targets on the basis of past trends. Using 2015 global averages of indicators with defined SDG targets, we calculated the global annualised rates of change required from 2015 to 2030 to meet these targets, and then identified in what percentiles the required global annualised rates of change fell in the distribution of country-level rates of change from 1990 to 2015. We took the mean of these global percentile values across indicators and applied the past rate of change at this mean global percentile to all health-related SDG indicators, irrespective of target definition, to estimate the equivalent 2030 global average value and percentage change from 2015 to 2030 for each indicator. Findings: The global median health-related SDG index in 2017 was 59·4 (IQR 35·4–67·3), ranging from a low of 11·6 (95% uncertainty interval 9·6–14·0) to a high of 84·9 (83·1–86·7). SDG index values in countries assessed at the subnational level varied substantially, particularly in China and India, although scores in Japan and the UK were more homogeneous. Indicators also varied by SDI quintile and sex, with males having worse outcomes than females for non-communicable disease (NCD) mortality, alcohol use, and smoking, among others. Most countries were projected to have a higher health-related SDG index in 2030 than in 2017, while country-level probabilities of attainment by 2030 varied widely by indicator. Under-5 mortality, neonatal mortality, maternal mortality ratio, and malaria indicators had the most countries with at least 95% probability of target attainment. Other indicators, including NCD mortality and suicide mortality, had no countries projected to meet corresponding SDG targets on the basis of projected mean values for 2030 but showed some probability of attainment by 2030. For some indicators, including child malnutrition, several infectious diseases, and most violence measures, the annualised rates of change required to meet SDG targets far exceeded the pace of progress achieved by any country in the recent past. We found that applying the mean global annualised rate of change to indicators without defined targets would equate to about 19% and 22% reductions in global smoking and alcohol consumption, respectively; a 47% decline in adolescent birth rates; and a more than 85% increase in health worker density per 1000 population by 2030. Interpretation: The GBD study offers a unique, robust platform for monitoring the health-related SDGs across demographic and geographic dimensions. Our findings underscore the importance of increased collection and analysis of disaggregated data and highlight where more deliberate design or targeting of interventions could accelerate progress in attaining the SDGs. Current projections show that many health-related SDG indicators, NCDs, NCD-related risks, and violence-related indicators will require a concerted shift away from what might have driven past gains—curative interventions in the case of NCDs—towards multisectoral, prevention-oriented policy action and investments to achieve SDG aims. Notably, several targets, if they are to be met by 2030, demand a pace of progress that no country has achieved in the recent past. The future is fundamentally uncertain, and no model can fully predict what breakthroughs or events might alter the course of the SDGs. What is clear is that our actions—or inaction—today will ultimately dictate how close the world, collectively, can get to leaving no one behind by 2030.
|
|
| 19. |
- Magnusson, Mikael, et al.
(författare)
-
Bioconversion of food waste to biocompatible wet-laid fungal films
- 2022
-
Ingår i: Materials & design. - : Elsevier. - 0264-1275 .- 1873-4197. ; 216
-
Tidskriftsartikel (refereegranskat)abstract
- The fungus Rhizopus delemar was grown on bread waste in a submerged cultivation process and wet-laid into films. Alkali or enzyme treatments were used to isolate the fungal cell wall. A heat treatment was also applied to deactivate biological activity of the fungus. Homogenization of fungal biomass was done by an iterative ultrafine grinding process. Finally, the biomass was cast into films by a wet-laid process. Ultrafine grinding resulted in densification of the films. Fungal films showed tensile strengths of up to 18.1 MPa, a Young's modulus of 2.3 GPa and a strain at break of 1.4%. Highest tensile strength was achieved using alkali treatment, with SEM analysis showing a dense and highly organized structure. In contrast, less organized structures were obtained using enzymatic or heat treatments. A cell viability assay and fluorescent staining confirmed the biocompatibility of the films. A promising route for food waste valorization to sustainable fungal wet-laid films was established. © 2022 The Authors
|
|
| 20. |
- Mirmohamadsadeghi, Safoora, et al.
(författare)
-
Enhanced solid-state biogas production from lignocellulosic biomass by organosolv pretreatment
- 2014
-
Ingår i: BioMed Research International. - : Hindawi Limited. - 2314-6133 .- 2314-6141. ; 2014
-
Tidskriftsartikel (refereegranskat)abstract
- Organosolv pretreatment was used to improve solid-state anaerobic digestion (SSAD) for methane production from three different lignocellulosic substrates (hardwood elm, softwood pine, and agricultural waste rice straw). Pretreatments were conducted at 150 and 180°C for 30 and 60 min using 75% ethanol solution as an organic solvent with addition of sulfuric acid as a catalyst. The statistical analyses showed that pretreatment temperature was the significant factor affecting methane production. Optimum temperature was 180°C for elmwood while it was 150°C for both pinewood and rice straw. Maximum methane production was 152.7, 93.7, and 71.4 liter per kg carbohydrates (CH), which showed up to 32, 73, and 84% enhancement for rice straw, elmwood, and pinewood, respectively, compared to those from the untreated substrates. An inverse relationship between the total methane yield and the lignin content of the substrates was observed. Kinetic analysis of the methane production showed that the process followed a first-order model for all untreated and pretreated lignocelluloses.
|
|
| 21. |
- Moaveni, Raouf, et al.
(författare)
-
Production of Polymeric Films from Orange and Ginger Waste for Packaging Application and Investigation of Mechanical and Thermal Characteristics of Biofilms
- 2024
-
Ingår i: Applied Sciences. - 2076-3417. ; 14:11
-
Tidskriftsartikel (refereegranskat)abstract
- Citrus waste has been used as a source of bioplastics for research in different ways. Because the juice industry produces significant amounts of residue each year, it would be advantageous to use the byproducts in the creation of new materials. Researchers have long explored eco-friendly methods to convert citrus and other organic waste into polymers for producing biodegradable films. The goal of this study is to create biofilms from orange waste (OW) and ginger waste (GW) using an ultrafine grinder and study the films’ properties. Since pectin has the ability to gel, and because cellulosic fibers are strong, citrus waste has been studied for its potential to produce biofilms. After being washed, dried, and milled, orange and ginger waste was shaped into films using a casting process. Tensile testing was used to determine the mechanical properties of biofilms, while dynamic mechanical thermal analysis (DMTA), thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC) were used to determine their thermal properties. As the number of grinding cycles increased, the suspension’s viscosity increased from 29 mPa.s to 57 mPa.s for OW and from 217 mPa.s to 376 mPa.s for GW, while the particle size in the suspension significantly decreased. For OW and GW films, the highest tensile strength was 17 MPa and 15 MPa, respectively. The maximum strain obtained among all films was 4.8%. All the tested films were stable up to 150 °C, and maximum degradation occured after 300 °C.
|
|
| 22. |
- Mohammadkhani, Ghasem, et al.
(författare)
-
New Solvent and Coagulating Agent for Development of Chitosan Fibers by Wet Spinning
- 2021
-
Ingår i: Polymers. - : MDPI AG. - 2073-4360. ; 13:13
-
Tidskriftsartikel (övrigt vetenskapligt/konstnärligt)abstract
- Adipic acid was evaluated as a novel solvent for wet spinning of chitosan fibers. A solvent with two carboxyl groups could act as a physical crosslinker between the chitosan chains, resulting in improved properties of the fibers. The performance of adipic acid was compared with conventional solvents, i.e., lactic, citric, and acetic acids. Chitosan solutions were injected into a coagulation bath to form monofilaments. Sodium hydroxide (NaOH) and its mixture with ethanol (EtOH) were used as coagulation agents. Scanning electron microscopy confirmed the formation of uniform chitosan monofilaments with an even surface when using adipic acid as solvent. These monofilaments generally showed higher mechanical strength compared to that of monofilaments produced using conventional solvents. The highest Young’s modulus, 4.45 GPa, was recorded for adipic acid monofilaments coagulated in NaOH-EtOH. This monofilament also had a high tensile strength of 147.9 MPa. Furthermore, taking advantage of chitosan insolubility in sulfuric acid (H2SO4) at room temperature, chitosan fibers were successfully formed upon coagulation in H2SO4-EtOH. The dewatering of fibers using EtOH before drying resulted in a larger fiber diameter and lower mechanical strength. Adipic acid fibers made without dehydration illustrated 18% (for NaOH), 46% (for NaOH-EtOH), and 91% (for H2SO4-EtOH) higher tensile strength compared to those made with dehydration.
|
|
| 23. |
- Mohsenzadeh, Abas, et al.
(författare)
-
Bioethylene Production from Ethanol : A Review and Techno-economical Evaluation.
- 2017
-
Ingår i: Challenges in Sustainability. - : Wiley-VCH Verlag GmbH & Co. KGaA. - 2297-6477. ; 4:2, s. 75-91
-
Tidskriftsartikel (refereegranskat)abstract
- Manufg. of bioethylene via dehydration of bioethanol is an alternative to the fossil-based ethylene prodn. and decreases the environmental consequences for this chem. commodity. A few industrial plants that utilize 1st generation bioethanol for the bioethylene prodn. already exist, although not functioning without subsidiaries. However, there is still no process producing ethylene from 2nd generation bioethanol. This study is divided into two parts. Different ethanol and ethylene prodn. methods, the process specifications and current technologies are briefly discussed in the first part. In the second part, a techno-economic anal. of a bioethylene plant was performed using Aspen plus and Aspen Process Economic Analyzer, where different qualities of ethanol were considered. The results show that impurities in the ethanol feed have no significant effect on the quality of the produced polymer-grade bioethylene. The capacity of the ethylene storage tank significantly affects the capital costs of the process. [on SciFinder(R)]
|
|
| 24. |
- Mousavi, Najmeh, et al.
(författare)
-
Bioconversion of Carrot Pomace to Value-Added Products : Rhizopus delemar Fungal Biomass and Cellulose
- 2023
-
Ingår i: FERMENTATION-BASEL. - : MDPI AG. - 2311-5637. ; 9:4
-
Tidskriftsartikel (refereegranskat)abstract
- Carrot pomace (CP) which is generated in a large volume in the juice production process, is rich in cellulose, hemicellulose, sugars, pectin, and minerals. However, in many previous investigations, only cellulose was purified and utilized while other components of CP were discarded as waste. Here, CP was valorized into fungal biomass and cellulose with the aim of utilizing all the CP components. Enzymatic pretreatments were applied to solubilize the digestible fraction of CP including hemicellulose, pectin, sucrose, and other sugars for fungal cultivation, while cellulose remained intact in the solid fraction. The dissolved fraction was utilized as a substrate for the cultivation of an edible fungus (Rhizopus delemar). Fungal cultivation was performed in shake flasks and bench-scale bioreactors. The highest fungal biomass concentration was obtained after pretreatment with invertase (5.01 g/L) after 72 h of cultivation (36 and 42% higher than the concentrations obtained after hemicellulase and pectinase treatments, respectively). Invertase pretreatment resulted in the hydrolysis of sucrose, which could then be taken up by the fungus. Carbohydrate analysis showed 28-33% glucan, 4.1-4.9% other polysaccharides, 0.01% lignin, and 2.7-7% ash in the CP residues after enzymatic pretreatment. Fourier transform infrared spectroscopy and thermogravimetric analysis also confirmed the presence of cellulose in this fraction. The obtained fungal biomass has a high potential for food or feed applications, or as a raw material for the development of biomaterials. Cellulose could be purified from the solid fraction and used for applications such as biobased-textiles or membranes for wastewater treatment, where pure cellulose is needed.
|
|
| 25. |
- Mousavi, Najmeh, et al.
(författare)
-
Production of Mycelium-Based Papers from Carrot Pomace and Their Potential Applications for Dye Removal
- 2024
-
Ingår i: Journal of Polymers and the Environment. - : Springer. - 1566-2543 .- 1572-8919.
-
Tidskriftsartikel (refereegranskat)abstract
- The Current study aimed at valorizing carrot pomace (CP), an abundant waste from the juice industry. A water-soluble fraction of CP was separated from solid fraction of CP (SFCP) and employed as feedstock for producing fungal biomass (FB) in bench-scale bioreactors. FB combined with SFCP were used to develop mycelium-based papers (MBP) using the wet-laid method. The potential and capacity of FB, SFCP and MBP to remove dye (methylene blue) from wastewater was then investigated. The maximum achieved dye removal was 92% when using a mixture of SFCP and FB in their suspended forms. The MBP with the lowest density (549 kg/m3) reached 83% dye elimination. The findings of this study support the valorization of carrot pomace, through environmentally benign processes, to mycelium-based papers with potential application in wastewater treatment.
|
|
