1.
Khanzadi, M Reza, 1983, et al.
(författare)
Calculation of the Performance of Communication Systems from Measured Oscillator Phase Noise
2014
Ingår i: IEEE Transactions on Circuits and Systems I: Regular Papers. - 1549-8328 .- 1558-0806. ; 61:5, s. 1553-1565
Tidskriftsartikel (refereegranskat) abstract
Oscillator phase noise (PN) is one of the major problems that affect the performance of communication systems. In this paper, a direct connection between oscillator measurements, in terms of measured single-side band PN spectrum, and the optimal communication system performance, in terms of the resulting error vector magnitude (EVM) due to PN, is mathematically derived and analyzed. First, a statistical model of the PN, considering the effect of white and colored noise sources, is derived. Then, we utilize this model to derive the modified Bayesian Cramer-Rao bound on PN estimation, and use it to find an EVM bound for the system performance. Based on our analysis, it is found that the influence from different noise regions strongly depends on the communication bandwidth, i.e., the symbol rate. For high symbol rate communication systems, cumulative PN that appears near carrier is of relatively low importance compared to the white PN far from carrier. Our results also show that 1/f^3 noise is more predictable compared to 1/f^2 noise and in a fair comparison it affects the performance less.
2.
Khanzadi, M Reza, 1983
(författare)
Modeling and Estimation of Phase Noise in Oscillators with Colored Noise Sources
2013
Licentiatavhandling (övrigt vetenskapligt/konstnärligt) abstract
The continuous increase in demand for higher data rates due to applications with massive number of users motivates the design of faster and more spectrum efficient communication systems. In theory, the current communication systems must be able to operate close to Shannon capacity bounds. However, the real systems perform below capacity limits, mainly due to channel estimation error and hardware impairments that have been neglected by idealistic or simplistic assumptions on the imperfections. Oscillator phase noise is one of the hardware impairments that is becoming a limiting factor in high data rate digital communication systems. Phase noise severely limits the performance of systems that employ dense constellations. Moreover, the level of phase noise (at a given off-set frequency) increases with carrier frequency which means that the problem of phase noise may be even more severe in systems with high carrier frequency.The focus of this thesis is on finding accurate statistical models of phase noise, as well as the design of efficient algorithms to mitigate the effect of this phenomenon on the performance of modern communication systems. First we derive the statistics of phase noise with white and colored noise sources in free-running and phase-locked-loop-stabilized oscillators. We investigate the relation between real oscillator phase noise measurements and the performance of communication systems by means of the proposed model. Our findings can be used by hardware and frequency generator designers to better understand the effect of phase noise with different sources on the system performance and optimize their design criteria respectively. Then, we study the design of algorithms for estimation of phase noise with colored noise sources. A soft-input maximum a posteriori phase noise estimator and a modified soft-input extended Kalman smoother are proposed. The performance of the proposed algorithms is compared against that of those studied in the literature, in terms of mean square error of phase noise estimation, and symbol error rate of the considered communication system. The comparisons show that considerable performance gains can be achieved by designing estimators that employ correct knowledge of the phase noise statistics. The performance improvement is more significant in low-SNR or low-pilot density scenarios.
3.
Nopchinda, Dhecha, 1991
(författare)
mm-Wave Data Transmission and Measurement Techniques: A Holistic Approach
2019
Doktorsavhandling (övrigt vetenskapligt/konstnärligt) abstract
The ever-increasing demand on data services places unprecedented technical requirements on networks capacity. With wireless systems having significant roles in broadband delivery, innovative approaches to their development are imperative. By leveraging new spectral resources available at millimeter-wave (mm-wave) frequencies, future systems can utilize new signal structures and new system architectures in order to achieve long-term sustainable solutions. This thesis proposes the holistic development of efficient and cost-effective techniques and systems which make high-speed data transmission at mm-wave feasible. In this paradigm, system designs, signal processing, and measurement techniques work toward a single goal; to achieve satisfactory system level key performance indicators (KPIs). Two intimately-related objectives are simultaneously addressed: the realization of efficient mm-wave data transmission and the development of measurement techniques to enable and assist the design and evaluation of mm-wave circuits. The standard approach to increase spectral efficiency is to increase the modulation order at the cost of higher transmission power. To improve upon this, a signal structure called spectrally efficient frequency division multiplexing (SEFDM) is utilized. SEFDM adds an additional dimension of continuously tunable spectral efficiency enhancement. Two new variants of SEFDM are implemented and experimentally demonstrated, where both variants are shown to outperform standard signals. A low-cost low-complexity mm-wave transmitter architecture is proposed and experimentally demonstrated. A simple phase retarder predistorter and a frequency multiplier are utilized to successfully generate spectrally efficient mm-wave signals while simultaneously mitigating various issues found in conventional mm-wave systems. A measurement technique to characterize circuits and components under antenna array mutual coupling effects is proposed and demonstrated. With minimal setup requirement, the technique effectively and conveniently maps prescribed transmission scenarios to the measurement environment and offers evaluations of the components in terms of relevant KPIs in addition to conventional metrics. Finally, a technique to estimate transmission and reflection coefficients is proposed and demonstrated. In one variant, the technique enables the coefficients to be estimated using wideband modulated signals, suitable for implementation in measurements performed under real usage scenarios. In another variant, the technique enhances the precision of noisy S-parameter measurements, suitable for characterizations of wideband mm-wave components.
4.
Zhang, Kewei, et al.
(författare)
Protecting GNSS Open Service-Navigation Message Authentication against Distance-Decreasing Attacks
Annan publikation (övrigt vetenskapligt/konstnärligt) abstract
As the security of global navigation satellite systems (GNSS) for civilian usage is increasingly important, navigation message authentication (NMA) significantly improves resilience to spoofing attacks. However, not all attacks can be effectively countered: a strong variant of replay/relay attacks, distance-decreasing (DD) attacks, can shorten pseudorange measurements, without manipulating the cryptographically protected navigation message, thus manipulating the position, velocity, and time solution undetected. First, we discuss how DD attacks can tamper with GNSS signals, demonstrating the attack effectiveness on a recorded Galileo signal. DD attacks might introduce bit errors to the forged signals, but the adversary can keep this error rate very low with proper attack parameter settings. Then, based on our mathematical model of the prompt correlator output of the tracking phase at the victim receiver, we find that the correlator output distribution changes in the presence of DD attacks. This leads us to apply hypothesis testing to detect DD attacks, notably a Goodness of Fit (GoF) test and a generalized likelihood ratio test (GLRT), depending on the victim’s knowledge on the DD attacks. Monte Carlo simulations are used to evaluate the detection probability and the receiver operating characteristic (ROC) curves for two tests, for different adversary configuration and noise settings. Then, we evaluate the effectiveness of the GoF and GLRT tests with a synthesized DD signal. Both tests can detect DD attacks with similar performance in high signal-to-noise ratio (SNR) environments. The GLRT detection probability is approximately 20% higher than that of the GoF test in low SNR environments.
5.
Pérez-Penichet, Carlos, et al.
(författare)
Poster abstract : Augmenting WSNs with interoperable 802.15.4 sensor tags
2017
Ingår i: SenSys 2017 - Proceedings of the 15th ACM Conference on Embedded Networked Sensor Systems. - New York, NY, USA : Association for Computing Machinery, Inc. - 9781450354592
Konferensbidrag (refereegranskat) abstract
The sensing capabilities of most sensor networks are fixed at the time of deployment. Adding new sensing capabilities to such networks is a costly and cumbersome process. We present Passive Sensor Tags, battery-free sensing devices that could be used to extend the sensing capabilities of an existing network. Sensor tags feature our new 802.15.4 receiver design which is suitable for micro-power operation, making battery-free tags possible. Because our tags can both transmit and receive 802.15.4 frames there is no need for any modification to the deployed hardware. We present preliminary measurements of transmission and reception range.
6.
Jang, Jeong Keun, et al.
(författare)
Area-efficient scheduling scheme based FFT processor for various OFDM systems
2018
Ingår i: 2018 IEEE ASIA PACIFIC CONFERENCE ON CIRCUITS AND SYSTEMS (APCCAS 2018). - : IEEE. - 9781538682401 ; , s. 338-341
Konferensbidrag (övrigt vetenskapligt/konstnärligt) abstract
This paper presents an area-efficient fast Fouriertransform (FFT) processor for orthogonal frequency-division multiplexing systems based on multi-path delay commutator architecture. This paper proposes a data scheduling scheme to reduce the number of complex constant multipliers. The proposed mixed-radix multi-path delay commutator FFT processor can support 128-, 256-, and 512-point FFT sizes. The proposed processor was synthesized using the Samsung 65-nm CMOS standard cell library. The proposed processor with eight parallel data paths can achieve a high throughput rate of up to 2.64 GSample/s at 330 MHz.
7.
Grabowski, Alexander, 1993
(författare)
VCSEL Equivalent Circuits and Silicon Photonics Integration
2022
Doktorsavhandling (övrigt vetenskapligt/konstnärligt) abstract
The vertical-cavity surface-emitting laser (VCSEL) is a light source of great importance for numerous industrial and consumer products. The main application areas are datacom and sensing. The datacom industry uses GaAs-based VCSELs for optical interconnects, the short-reach fiber optical communication links used to transfer large amounts of data at high rates between units within data centers and supercomputers. In the area of sensing, VCSELs are largely used in consumer products such as smart phones (e.g. face ID and camera auto focus), computer mice, and automobiles (e.g. gesture recognition and LIDAR for autonomous driving). In this work, an advanced physics-based equivalent circuit model for datacom VCSELs has been developed. The model lends itself to co-design and co-optimization with driver and receiver ICs, thereby enabling higher data rate transceivers with bandwidth limited VCSELs and photodiodes. The model also facilitates an understanding of how each physical process within the VCSEL affects the VCSEL static and dynamic performance. It has been applied to study the impact of carrier transport and capture on VCSEL dynamics. The work also includes micro-transfer-printing of GaAs-based single-mode VCSELs on silicon nitride photonic integrated circuits (PICs). Such PICs are increasingly used for e.g. compact and highly functional bio-photonic sensors. Transfer printing of VCSELs enables the much-needed on-PIC integration of power efficient light sources. The bottom-emitting VCSELs are printed above grating couplers on the PIC and optical feedback is used to control the polarization for efficient coupling to the silicon nitride waveguide. Wavelength tuning, as required by the bio-sensing application, is achieved by direct current modulation.
8.
Gustavsson, Ulf, 1975
(författare)
From Noise-Shaped Coding to Energy Efficiency - One bit at the time
2011
Doktorsavhandling (övrigt vetenskapligt/konstnärligt) abstract
Three parameters that drive the research and development of future RF transmitter technologies for high speed wireless communication today are energy efficiency, flexibility and reduction of the physical footprint. This thesis treats the use of single-bit quantization in conjunction with a method called Noise-Shaped Coding (NSC), as an enabler for these parameters, foremost in terms of energy efficiency.The first part of the thesis provides a short introduction to the common Radio Frequency Power Amplifier (RFPA) power efficiency enhancement techniques. The pulsed RF transmitter is introduced in which the RFPA is used as a switch, modulated by a single-bit quantized signal which allows it to operate solely at its two most efficient states.The second part of the thesis provides an introduction to the concept of NSC and the underlying idea of how high signal quality can be achieved with one bit quantization of the signal amplitude. A particular method of implementing NSC, namely the ΣΔ-modulator, is introduced and some common methods for design and analysis are discussed. An optimization-based approach to ΣΔ-modulator design is proposed and benchmarked against conventional methods in terms of its ability to shape the power spectral density of the quantization noise according to a given reconstruction filter response, minimizing the reconstructed error metric.The third and final part of the thesis focuses specifically on the application of ΣΔ-modulation in a pulsed RF transmitter context. The concepts of band-pass and baseband ΣΔ-modulation are introduced. A few important challenges related to the use of ΣΔ-modulation in a pulsed RF-transmitter context are identified. A ΣΔ-modulator topology which handles a complex input signal is investigated in great detail and advantages compared to conventional methods for using ΣΔ-modulation are unveiled by means of theoretical analysis and simulations. A method for suppressing the quantization noise within a frequency band surrounding the modulated RF carrier, enabling the use of more wideband reconstruction filter and moderate pulse-rates, is also presented. A detailed theoretical analysis reveals how optimized Noise-Shaped Coding, as provided by the optimization method introduced in the second part, can be deployed in order to improve the system performance. Finally, the method is validated by experimental measurements on two different high efficiency RFPAs at 1 and 3.5 GHz respectively, showing promising results.
9.
Seyedhosseinzadeh, Neda, et al.
(författare)
A 100–140 GHz SiGe-BiCMOS sub-harmonic down-converter mixer
2017
Ingår i: 2017 12th European Microwave Integrated Circuits Conference (EuMIC). - 9782874870484 ; 2017-January
Konferensbidrag (refereegranskat) abstract
This paper demonstrates a wideband, subharmonic down converting mixer using a commercial 130-nm SiGe-BiCMOS technology. The mixer adopts a frequency doubling LO-stage, a differential switched-transconductance RF-stage, on-chip LO and RF baluns, and two emitter-follower buffer-stages. The measured results exhibit a maximum conversion gain up to 2.6 dB over the frequency range of 100 to 140 GHz with a LO power of 5 dBm. The mixer achieves an input referred 1-dB compression point of −7.2 dBm, with a DC power of 46.3 mW, including 26.7 mW for buffer-stages. It demonstrates also up to 12 GHz 3-dB IF bandwidth, which to the authors' best knowledge, is the highest obtained among active sub-harmonic mixers operating above 100 GHz. The chip occupies 0.4 mm2, including pads.
10.
Alhashimi, Anas, 1978-
(författare)
The application of auto regressive spectrum modeling for identification of the intercepted radar signal frequency modulation
2012
Ingår i: Inventi Impact - Telecom. - Bhopal, India : Inventi Journals Pvt.Ltd.. - 2249-1414 .- 2230-8172. ; 2012:3
Tidskriftsartikel (refereegranskat) abstract
In the Electronic Warfare receivers, it is important to know the type of modulation of the intercepted Radar signals (MOP modulation on pulse). This information can be very helpful in identifying the type of Radar present and to take the appropriate actions against it. In this paper, a new signal processing method is presented to identify the FM (Frequency Modulation) pattern from the received Radar pulses. The proposed processing method based on Auto Regressive Spectrum Modelling used for digital modulation classification [1]. This model uses the instantaneous frequency and instantaneous bandwidth as obtained from the roots of the autoregressive polynomial. The instantaneous frequency and instantaneous bandwidth together were used to identify the type of modulation in the Radar pulse. Another feature derived from the instantaneous frequency is the frequency rate of change. The frequency rate of change was used to extract the pattern of the frequency change. Results show that this method works properly even for low signal to noise ratios.
11.
Bao, Husileng, 1991, et al.
(författare)
Wideband mm-wave Spectrum-Efficient Transmitter Using Low-Pass Sigma–Delta-Over-Fiber Architecture
2023
Ingår i: IEEE Microwave and Wireless Technology Letters. - 2771-9588 .- 2771-957X. ; 33:10, s. 1505-1508
Tidskriftsartikel (refereegranskat) abstract
The millimeter-wave band offers large bandwidth and promises high data rates for wireless communication systems. This work proposes a millimeter-wave radio-over-fiber architecture suitable for wideband mm-wave communication, using a lowpass sigma-delta modulation approach. The central unit generates baseband sigma-delta bitstreams, in-phase/quadrature (I/Q) components, which are transported to a remote radio head (RRH) using a standard QSFP28 optical interconnect link connection. In the RRH, the baseband I/Q signals are upconverted to the millimeter-wave band, amplified, and transmitted through an antenna. The performance of the resulting sigma-delta-over-fiber transmitter architecture is experimentally verified at 28 GHz, demonstrating a state-of-the-art symbol rate up to 1.5 Gsym/s. Furthermore, in over-the-air measurements, the architecture is shown to support 1 Gsym/s with 5.9% error vector magnitude for 64/256/1024 quadrature amplitude modulation cases over a 5 m wireless distance. The results demonstrate the feasibility of the proposed architecture for the realization of wideband millimeterwave distributed antenna systems.
12.
Bencivenni, Carlo, 1986
(författare)
Aperiodic Array Synthesis for Telecommunications
2017
Doktorsavhandling (övrigt vetenskapligt/konstnärligt) abstract
Arrays of antennas offer important advantages over single-element antennas and are thus a key part of most advanced communication systems. The majority of current arrays are based on a classical regular layout, which offer simple design criteria despite some limitations. Aperiodic arrays can reduce the number of elements and improve the performance, however their design is far more challenging. This thesis focuses on the synthesis of aperiodic arrays, advancing the state-of-the-art of phased arrays and pioneering the application to Multiple-Input Multiple-Output (MIMO) systems.In satellite communications (SATCOM), aperiodic sparse arrays have the potential for drastically reducing the costs of massive antennas. Most available synthesis methods are however either intractable, suboptimal or limited for such demanding scenarios. We propose a deterministic and efficient approach based on Compressive Sensing, capable of accounting for electromagnetic phenomena and complex specifications. Some of the key contributions include the extension to the design of multi-beam, modular, multi-element, reconfigurable and isophoric architectures.The same approach is successfully applied to the design of compact arrays for Point-to-Point (PtP) backhauling. The aperiodicity is used here instead to reduce the side lobes and meet the target radiation envelope with high aperture efficiency. A dense, column arranged, slotted waveguide isophoric array has been successfully designed, manufactured and measured.Line-of-Sight (LoS) MIMO can multiply the data rates of classical Single-Input Single-Output (SISO) backhauling systems, however it suffers from limited installation flexibility. We demonstrate how aperiodic arrays and their switched extensions can instead overcome this shortcoming. Since a small number of antennas are typically used, an exhaustive search is adopted for the synthesis.Massive Multi-User (MU) MIMO is envisioned as a key technology for future 5G systems. Despite the prevailing understanding, we show how the MIMO performance is affected by the array layout. To exploit this, we propose a new hybrid statistical-density tapered synthesis approach. Results show a significant improvement in minimum power budget, capacity and amplifier efficiency, especially for massive and/or crowded systems
13.
Chani Cahuana, Jessica, 1988, et al.
(författare)
Digital Predistortion Parameter Identification for RF Power Amplifiers Using Real-Valued Output Data
2017
Ingår i: IEEE Transactions on Circuits and Systems II: Express Briefs. - 1549-7747 .- 1558-3791. ; 64:10, s. 1227-1231
Tidskriftsartikel (refereegranskat) abstract
This brief presents a novel digital predistortion (DPD) parameter identification technique that requires only the acquisition of either the in-phase (I) or the quadrature (Q) component of the power amplifier (PA) output signal. To this end, an approach that allows us to estimate the parameters of a model using only one of the IQ components of the model output is presented. Based on experimental results, it is shown that the proposed real-valued measurements based technique can offer similar linearization capabilities as its complex-valued counterparts. The experimental results also indicate that the proposed technique can be used in combination with other techniques that focus on reducing the speed of analog-to-digital converters (ADCs)
14.
Chen, Jingjing, 1982, et al.
(författare)
10 Gbps 16QAM transmission over a 70/80 GHz (E-band) radio test-bed
2012
Ingår i: European Microwave Week 2012: "Space for Microwaves", EuMW 2012, Conference Proceedings - 7th European Microwave Integrated Circuits Conference, EuMIC 2012. - : IEEE. - 9782874870286 - 9781467323024 - 9782874870262 ; , s. 556-559
Konferensbidrag (refereegranskat) abstract
A millimeter-wave radio test-bed is implemented which demonstrates 16QAM transmission over 70/80 GHz band for data rate up to 10 Gbps. Performance of the 16QAM transmitter and receiver is evaluated in a loop-back lab set-up. With the proposed 10 Gbps on single carrier system architecture, it is possible to achieve 40 Gbps over a 5 GHz bandwidth when combined with polarization and spatial multiplexing.
15.
Cheng, Hei Victor
(författare)
Aspects of Power Allocation in Massive MIMO
2016
Licentiatavhandling (övrigt vetenskapligt/konstnärligt) abstract
The past decades have seen a rapid growth of mobile data trac, both in terms of connected devices and data rate. To satisfy the ever growing data trac demand in wireless communication systems, the current cellular systems have to be redesigned to increase both spectral eciency and energy eciency. Massive MIMO (Multiple-Input-Multiple-Output) is one solution that satisfy both requirements. In massive MIMO systems, hundreds of antennas are employed at the base station to provide service to many users at the same time and frequency. This enables the system to serve the users with uniformly good quality of service simultaneously, with low-cost hardware and without using extra bandwidth and energy. To achieve this, proper resource allocation is needed. Among the available resources, transmit power is one of the most important degree of freedom to control the spectral eciency and energy eciency. Due to the use of excessive number of antennas and low-end hardware at the base station, new aspects of power allocation compared to current systems arises. In the rst part of the thesis, a new uplink power allocation schemes that based on long term channel statistics is proposed. Since quality of the channel estimates is crucial in massive MIMO, in addition to data power allocation, joint power allocation that includes the pilot power as additional variable should be considered. Therefore a new framework for power allocation that matches practical systems is developed, as the methods developed in the literature cannot be applied directly to massive MIMO systems. Simulation results conrm the advantages brought by the the proposed new framework. In the second part of the thesis, we investigate the eects of using low-end ampliers at the base stations. The non-linear behavior of power consumption in these ampliers changes the power consumption model at the base station, thereby changes the power allocation. Two dierent scenarios are investigated and both results show that a certain number of antennas can be turned o in low load scenarios.
16.
Farhadi, Hamed, 1983
(författare)
On the throughput of wireless interference networks with limited feedback
2011
Ingår i: IEEE International Symposium on Information Theory Proceedings (ISIT'11). - 2157-8095. - 9781457705960 ; , s. 762 - 766
Konferensbidrag (refereegranskat) abstract
Considering a single-antenna M-user interference channel with symmetrically distributed channel gains, when the channel state information (CSI) is globally available, applying the ergodic interference alignment scheme, each transmitter-receiver pair achieves a rate proportional to ½ of a single user's interference-free achievable rate. This is substantially higher than the achievable rate of the conventional orthogonal transmission schemes such as TDMA. Since the rigid requirement on the CSI may be difficult to realize in practice, in this paper we investigate the performance of applying the ergodic interference alignment scheme when the estimation of each channel gain is made globally known through exploiting only a limited feedback signal from the associated receiver of that channel. Under a block fading environment, we provide a lower bound on the achievable average throughput of the network. Our results imply that the better performance of interference alignment over TDMA may still exist even without the assumption of perfect CSI. Also, the trade off between allocating feedback rate of each receiver to the desired channel or the interference channels at deferent SNR region investigated.
17.
Grudén, Mathias
(författare)
Wireless Sensor Network Systems in Harsh Environments and Antenna Measurement Techniques
2014
Doktorsavhandling (övrigt vetenskapligt/konstnärligt) abstract
Wireless sensor network (WSN) has become a hot topic lately. By using WSN things that previously were difficult or impossible to measure has now become available. One of the main reasons using WSN for monitoring is to save money by cost optimization and/or increase safety by letting the user knowing the physical status of the monitored structure. This thesis considers four main topics, empirical testing of WSN in harsh environments, antenna designs, antenna measurements and radio environment emulation.The WSN has been tested in train environment for monitoring of ball bearings and inside jet engines to monitor strain of blades and temperatures. In total, two investigations have been performed aboard the train wagon and one in the jet engine. The trials have been successful and provide knowledge of the difficulties with practical WSN applications. The key issues for WSN are robust communication, energy management (including scavenging) and physical robustness.For the applications of WSN in harsh environments antennas has to be designed. In the thesis, two antennas has been designed, one for train environment and one for the receiver in the jet engine. In the train environment, a more isotropic radiation pattern is preferable; hence a small dual layered patch antenna is designed. The antenna is at the limit of being electrically small; hence slightly lower radiation efficiency is measured. For the WSN in the jet engine, a directive patch array is designed on an ultra-thin and flexible substrate. The thin substrate of the antenna causes rather lower radiation efficiency. But the antenna fulfils the requirements of being conformal and directive.In reverberation chambers are used to measure antennas, but there are difficulties to provide a realistic radio environment, for example outdoor or on-body. In this thesis, a large reverberation chamber is designed and verified. It enables measurement between 400 MHz and 3 GHz. Also, a sample selection method is designed to provide a post processing possibilities to emulate the radio environment inside the chamber. The method is to select samples from a data set that corresponds to a desired probability density function. The method presented in this thesis is extremely fast but the implementation of the method is left for future research.
18.
Haque, Muhammad Fahim Ul
(författare)
Pulse-Width Modulated RF Transmitters
2017
Doktorsavhandling (övrigt vetenskapligt/konstnärligt) abstract
The market for wireless portable devices has grown signicantly over the recent years.Wireless devices with ever-increased functionality require high rate data transmissionand reduced costs. High data rate is achieved through communication standards such asLTE and WLAN, which generate signals with high peak-to-average-power ratio (PAPR),hence requiring a power amplier (PA) that can handle a large dynamic range signal. Tokeep the costs low, modern CMOS processes allow the integration of the digital, analogand radio functions on to a single chip. However, the design of PAs with large dynamicrange and high eciency is challenging due to the low voltage headroom.To prolong the battery life, the PAs have to be power-ecient as they consume a sizablepercentage of the total power. For LTE and WLAN, traditional transmitters operatethe PA at back-o power, below their peak efficiency, whereas pulse-width modulation(PWM) transmitters use the PA at their peak power, resulting in a higher efficiency.PWM transmitters can use both linear and SMPAs where the latter are more power efficient and easy to implement in nanometer CMOS. The PWM transmitters have a higher efficiency but suffer from image and aliasing distortion, resulting in a lower dynamic range,amplitude and phase resolution.This thesis studies several new transmitter architectures to improve the dynamicrange, amplitude and phase resolution of PWM transmitters with relaxed filtering requirements.The architectures are suited for fully integrated CMOS solutions, in particular forportable applications.The first transmitter (MAF-PWMT) eliminates aliasing and image distortions whileallowing the use of SMPAs by combining RF-PWM and band-limited PWM. The transmittercan be implemented using all-digital techniques and exhibits an improved linearity and spectral performance. The approach is validated using a Class-D PA based transmitter where an improvement of 10.2 dB in the dynamic range compared to a PWM transmitter for a 1.4 MHz of LTE signal is achieved.The second transmitter (AC-PWMT) compensates for aliasing distortion by combining PWM and outphasing. It can be used with switch-mode PAs (SMPAs) or linear PAs at peak power. The proposed transmitter shows better linearity, improved spectral performanceand increased dynamic range as it does not suffer from AM-AM distortion of the PAs and aliasing distortion due to digital PWM. The idea is validated using push-pull PAs and the proposed transmitter shows an improvement of 9 dB in the dynamic rangeas compared to a PWM transmitter using digital pulse-width modulation for a 1.4 MHzLTE signal.The third transmitter (MD-PWMT) is an all-digital implementation of the second transmitter. The PWM is implemented using a Field Programmable Gate Array(FPGA) core, and outphasing is implemented as pulse-position modulation using FPGA transceivers, which drive two class-D PAs. The digital implementation offers the exibility to adapt the transmitter for multi-standard and multi-band signals. From the measurement results, an improvement of 5 dB in the dynamic range is observed as compared to an all-digital PWM transmitter for a 1.4 MHz LTE signal.The fourth transmitter (EP-PWMT) improves the phase linearity of an all-digital PWM transmitter using PWM and asymmetric outphasing. The transmitter uses PWM to encode the amplitude, and outphasing for enhanced phase control thus doubling the phase resolution. The measurement setup uses Class-D PAs to amplify a 1.4 MHz LTEup-link signal. An improvement of 2.8 dB in the adjacent channel leakage ratio is observed whereas the EVM is reduced by 3.3 % as compared to an all-digital PWM transmitter.The fifth transmitter (CRF-ML-PWMT) combines multilevel and RF-PWM, whereas the sixth transmitter (CRF-MP-PMWT) combines multiphase PWM and RF-PWM. Both transmitters have smaller chip area as compared to the conventional multiphase and multilevel PWM transmitters, as a combiner is not required. The proposed transmitters also show better dynamic range and improved amplitude resolution as compared to conventional RF-PWM transmitters.The solutions presented in this thesis aims to enhance the performance and simplify the digital implementation of PWM-based RF transmitters.
19.
Jobs, Magnus, 1984-
(författare)
Wireless Interface Technologies for Sensor Networks
2015
Doktorsavhandling (övrigt vetenskapligt/konstnärligt) abstract
The main focus of the work presented in this thesis concerns the development and improvement of Wireless Sensor Networks (WSNs) as well as Wireless Body Area Networks (WBANs). WSN consist of interlinked, wireless devices (nodes) capable of relaying data wirelessly between the nodes. The applications of WSNs are very broad and cover both wireless fitness monitoring systems such as pulse watches or wireless temperature monitoring of buildings, among others.The topics investigated in the work presented within this thesis covers antenna design, wireless propagation environment evaluation and modeling, adaptive antenna control and wireless nodes system design and evaluation. In order to provide an end-user suitable solution for wireless nodes the devices require both small form factor and good performance in order to be competitive on the marked and thus the main part of this thesis focuses on techniques developed and data collected to help achieve these goals. Several different prototype systems have been developed which have been used to measure data by the Swedish Defence Research Agency (FOI), GKN Aerospace Sweden AB, the Swedish Transport Administration. The system developed with GKN Aerospace was used to do real-time test measurements inside a running RM12 jet engine and required a substantial amount of measurements, environmental modeling and system validation in order to properly design a wireless system suitable for the harsh and fast fading environment inside a jet engine. For FOI improvements were made on a wearable wireless body area network initially developed during the authors master thesis work. Refinements included work on new generation wireless nodes, antenna packaging and node-supported diversity techniques.Work and papers regarding the design of different types of antennas suitable for wireless nodes are presented. The primary constraints on the presented antennas are the limited electrical size. The types of antennas developed include electrically small helix antennas manufactured both on stretchable substrates consisting of a PDMS substrate with Galinstan as the liquid metal conductors, screen printed silver ink for helix antennas and conformal dual patch antennas for wireless sensor nodes. Other standard type antennas are included on the wireless sensors as well.
20.
Kang, Jeongwan, et al.
(författare)
Optimized Switching Between Sensing and Communication for mmWave MU-MISO Systems
2022
Ingår i: 2022 Ieee International Conference On Communications Workshops (Icc Workshops). - : Institute of Electrical and Electronics Engineers (IEEE). ; , s. 498-503
Konferensbidrag (refereegranskat) abstract
In this paper, we propose a scheme optimizing the per-user channel sensing duration in millimeter-wave (mmWave) multi-user multiple-input single-output (MU-MISO) systems. For each user, the BS predicts the effective rate to be achieved after pilot transmission. Then, the channel sensing duration of each user is optimized by ending the pilot transmission when the predicted rate is lower than the current rate. The robust regularized zero-forcing (RRZF) precoder and equal power allocation (EPA) are adopted to transmit sensing pilots and data. Numerical results show that the more severe the interference among users, the longer channel sensing duration is required. Moreover, the proposed scheme results in a higher sum rate compared to benchmark schemes.
21.
Kylin, Carl, 1996
(författare)
Over the air calibration of transmitter distortion for active antenna arrays
2024
Licentiatavhandling (övrigt vetenskapligt/konstnärligt) abstract
Radar systems for air surveillance have long utilised large antenna arrays to generate high enough gain for a narrow enough transmitted beam. In most modern systems this is accomplished through the use of large active electronically steered antenna arrays. Calibrating a large active antenna array is a challenging endeavour. Distorting effects stemming from the amplifying circuitry can have a non-negligible effect on the transmitted signal, and the effects can vary across the array. In modern and future transmitter arrays, individually controlled antenna elements will be a feature. With such systems, distortion that varies over an array can be combatted. One challenge is how to collect data about what signal is being transmitted and in what way the actual signal differs from the desired transmitted signal. The work presented in this thesis studies aspects of characterising a model describing the distortion generated in an active antenna array using an over the air channel. Specifically, the first included article presents a method where signals collected using an over the air channel generated by targets of opportunity are used to estimate the parameters of a non-linearly parametrised model for a radar transmitter. In this article, the radar is assumed to transmit different signals on each antenna element. The second included article studies conditions for identifiability for the setup in the first article as well as for other similar setups. These works constitute the second part of this thesis. To put this work into context, the first part of this thesis presents an overview of the problems caused by distortion in a radar system. This is investigated under different modelling assumptions and for radars operating in a number of different modes.
22.
Liu, Edward, et al.
(författare)
A 25-40 GHz Three-Way Power Amplifier with No Load Modulation Achieving Broadband Deep Power Back-Off Efficiency Enhancement
2024
Ingår i: Digest of Papers - IEEE Radio Frequency Integrated Circuits Symposium. - 1529-2517. - 9798350359473 ; , s. 127-130
Konferensbidrag (refereegranskat) abstract
This paper presents a millimeter-wave (mm-Wave) power amplifier (PA) topology that avoids the trade-off between bandwidth and load modulation. The proposed topology uses three PA paths and can achieve efficiency enhancement at power back-off without load modulation. With a 100 MHz 5G NR FR2 1-CC 64-QAM signal, this PA achieves average power and PAE of 6.45 - 12.61 dBm and 5.9 - 16.4% from 25 - 40 GHz, respectively. With a 200 MHz signal, average power and PAE are 5.58 - 11.1 dBm and 4.8 - 13.3%, respectively.
23.
Liu, Yang, et al.
(författare)
A Study Towards Enhanced Reliability Performance of Remote Control and Monitoring Application Over Commercial Wireless Communication Networks
2006
Ingår i: 2006 International Conference on Wireless Communications, Networking and Mobile Computing. - : Institute of Electrical and Electronics Engineers (IEEE). - 1424405173 - 1424405173 ; , s. 1-4
Konferensbidrag (refereegranskat) abstract
Remote control and monitoring systems provide many useful operating advantages in industrial automation and demand highly reliable and secure communication means. Their widespread use is, however, limited because of the high cost of current communications in use making them economically infeasible. Hence, there is a need to develop new low cost communication and control concepts by making such solutions economically feasible. In this paper, we present a scheme for implementing reliable wireless communication links for application of remote control and monitoring system based on current available commercial wireless communication networks, e.g. GPRS/EDGE/UMTS. The reliability enhancement over wireless networks has been proposed and its performance has been studied. This paper examines the proposed solution by means of both analytical and numerical evaluation, and has shown that the demanded reliability performance can be met by using only commercial wireless communication networks.
24.
Mollén, Christopher, 1987-
(författare)
High-End Performance with Low-End Hardware : Analysis of Massive MIMO Base Station Transceivers
2017
Doktorsavhandling (övrigt vetenskapligt/konstnärligt) abstract
Massive MIMO (multiple-input–multiple-output) is a multi-antenna technology for cellular wireless communication, where the base station uses a large number of individually controllable antennas to multiplex users spatially. This technology can provide a high spectral efficiency. One of its main challenges is the immense hardware complexity and cost of all the radio chains in the base station. To make massive MIMO commercially viable, inexpensive, low-complexity hardware with low linearity has to be used, which inherently leads to more signal distortion. This thesis investigates how the degenerated linearity of some of the main components—power amplifiers, analog-to-digital converters (ADCs) and low-noise amplifiers—affects the performance of the system, with respect to data rate, power consumption and out-of-band radiation. The main results are: Spatial processing can reduce PAR (peak-to-average ratio) of the transmit signals in the downlink to as low as 0B; this, however, does not necessarily reduce power consumption. In environments with isotropic fading, one-bit ADCs lead to a reduction in effective signal-to-interference-and-noise ratio (SINR) of 4dB in the uplink and four-bit ADCs give a performance close to that of an unquantized system. An analytical expression for the radiation pattern of the distortion from nonlinear power amplifiers is derived. It shows how the distortion is beamformed to some extent, that its gain never is greater than that of the desired signal, and that the gain of the distortion is reduced with a higher number of served users and a higher number of channel taps. Nonlinear low-noise amplifiers give rise to distortion that partly combines coherently and limits the possible SINR. It is concluded that spatial processing with a large number of antennas reduces the impact of hardware distortion in most cases. As long as proper attention is paid to the few sources of coherent distortion, the hardware complexity can be reduced in massive MIMO base stations to overcome the hardware challenge and make massive MIMO commercial reality.
25.
Nilsson, Emil, et al.
(författare)
Ultra Low Power Wake-Up Radio Using Envelope Detector and Transmission Line Voltage Transformer
2013
Ingår i: IEEE Journal on Emerging and Selected Topics in Circuits and Systems. - : Institute of Electrical and Electronics Engineers (IEEE). - 2156-3357 .- 2156-3365. ; 3:1, s. 5-12
Tidskriftsartikel (refereegranskat) abstract
An ultra-low power wake-up radio receiver using no oscillators is described. The radio utilizes an envelope detector followed by a baseband amplifier and is fabricated in a 130-nm complementary metal-oxide-semiconductor process. The receiver is preceded by a passive radio-frequency voltage transformer, also providing 50 Omega antenna matching, fabricated as transmission lines on the FR4 chip carrier. A sensitivity of -47 dBm with 200 kb/s on-off keying modulation is measured at a current consumption of 2.3 mu A from a 1 V supply. No trimming is used. The receiver accepts a dBm continuous wave blocking signal, or modulated blockers 6 dB below the sensitivity limit, with no loss of sensitivity.
