| 1. |
- Xu, Jinghao, et al.
(författare)
-
Short-term creep behavior of an additive manufactured non-weldable Nickel-base superalloy evaluated by slow strain rate testing
- 2019
-
Ingår i: Acta Materialia. - : Elsevier BV. - 1359-6454 .- 1873-2453. ; 179, s. 142-157
-
Tidskriftsartikel (refereegranskat)abstract
- Additive manufacturing (AM) of high γ′ strengthened Nickel-base superalloys, such as IN738LC, is of high interest for applications in hot section components for gas turbines. The creep property acts as the critical indicator of component performance under load at elevated temperature. However, it has been widely suggested that the suitable service condition of AM processed IN738LC is not yet fully clear. In order to evaluate the short-term creep behavior, slow strain rate tensile (SSRT) tests were performed. IN738LC bars were built by laser powder-bed-fusion (L-PBF) and then subjected to hot isostatic pressing (HIP) followed by the standard two-step heat treatment. The samples were subjected to SSRT testing at 850 °C under strain rates of 1 × 10−5/s, 1 × 10−6/s, and 1 × 10−7/s. In this research, the underlying creep deformation mechanism of AM processed IN738LC is investigated using the serial sectioning technique, electron backscatter diffraction (EBSD), transmission electron microscopy (TEM). On the creep mechanism of AM polycrystalline IN738LC, grain boundary sliding is predominant. However, due to the interlock feature of grain boundaries in AM processed IN738LC, the grain structure retains its integrity after deformation. The dislocation motion acts as the major accommodation process of grain boundary sliding. Dislocations bypass the γ′ precipitates by Orowan looping and wavy slip. The rearrangement of screw dislocations is responsible for the formation of subgrains within the grain interior. This research elucidates the short-creep behavior of AM processed IN738LC. It also shed new light on the creep deformation mechanism of additive manufactured γ′ strengthened polycrystalline Nickel-base superalloys.
|
|
| 2. |
- Grolig, Jan Gustav, 1986
(författare)
-
Coated Ferritic Stainless Steels as Interconnects in Solid Oxide Fuel Cells - Material Development and Electrical Properties
- 2015
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Solid oxide fuel cells (SOFCs) are attracting increasing interest as devices with potentialuses in decentralized and clean electricity and heat production. Several challengeswith respect to materials have to be overcome to achieve efficiencies and life-spansthat are sufficient for long-term applications.An important element of an SOFC stack is the interconnect component, which connectstwo adjacent fuel cell elements. Interconnects, which are commonly composedof ferritic stainless steels, have to be corrosion-resistant, mechanically stable and costoptimized.This work aimed to investigate economic solutions for interconnect materials and tounderstand the underlying mechanisms of degradation and electrical conduction ofthese materials. Mainly two substrates, a commercially available steel (AISI 441) anda ferritic stainless steel that was optimized for an SOFC application (Sandvik SanergyHT) were combined with different barrier coatings and exposed to a cathode-sideatmosphere. A method was developed that allows for the electrical characterizationof promising material systems and model alloys, thereby facilitating a fundamentalunderstanding of the dominant electrical conduction processes linked to the oxidescales that grow on interconnects. The AISI 441 steel coated with reactive elementsand cobalt showed good corrosion and chromium evaporation profiles, while AISI 441coated with cerium and cobalt also had promising electrical properties. The SanergyHT steel was examined with coatings of copper and iron and copper and manganese,respectively. The corrosion and chromium evaporation profiles of Sanergy HT wereimproved by coating with copper and iron. The copper and iron-coated Sanergy HTshowed lower area specific resistance values than cobalt-coated Sanergy HT. Chromia,which is the main constituent of oxide scales, was synthesized using differentmethods. The electrical properties of chromia were found to be sensitive to not onlyimpurities, but also heat treatment. Finally the electrical properties of cobalt- andcobalt cerium-coated Sanergy HT steels were investigated. It was revealed that theaddition of cerium improved the conductivity of the interconnect by both slowingdown chromia growth and preventing the outward diffusion of iron into the spinel.
|
|
| 3. |
- Chen, Zhe, et al.
(författare)
-
Nano-scale characterization of white layer in broached Inconel 718
- 2017
-
Ingår i: Materials Science & Engineering A: Structural Materials: Properties, Microstructure and Processing. - Amsterdam : Elsevier BV. - 0921-5093 .- 1873-4936. ; 684, s. 373-384
-
Tidskriftsartikel (refereegranskat)abstract
- The formation mechanism of white layers during broaching and their mechanical properties are not well investigated and understood to date. In the present study, multiple advanced characterization techniques with nano-scale resolution, including transmission electron microscopy (TEM), transmission Kikuchi diffraction (TKD), atom probe tomography (APT) as well as nano-indentation, have been used to systematically examine the microstructural evolution and corresponding mechanical properties of a surface white layer formed when broaching the nickel-based superalloy Inconel 718.TEM observations showed that the broached white layer consists of nano-sized grains, mostly in the range of 20–50 nm. The crystallographic texture detected by TKD further revealed that the refined microstructure is primarily caused by strong shear deformation. Co-located Al-rich and Nb-rich fine clusters have been identified by APT, which are most likely to be γ′ and γ′′ clusters in a form of co-precipitates, where the clusters showed elongated and aligned appearance associated with the severe shearing history. The microstructural characteristics and crystallography of the broached white layer suggest that it was essentially formed by adiabatic shear localization in which the dominant metallurgical process is rotational dynamic recrystallization based on mechanically-driven subgrain rotations. The grain refinement within the white layer led to an increase of the surface nano-hardness by 14% and a reduction in elastic modulus by nearly 10% compared to that of the bulk material. This is primarily due to the greatly increased volume fraction of grain boundaries, when the grain size was reduced down to the nanoscale.
|
|
| 4. |
- Dimitrios, Nikas, et al.
(författare)
-
Effect of annealing on microstructure in railway wheel steel
- 2022
-
Ingår i: 42Nd Riso International Symposium On Materials Science. - : Institute of Physics Publishing (IOPP). ; 1249
-
Konferensbidrag (refereegranskat)abstract
- Railway wheels are commonly made from medium carbon steels (similar to 0.55 wt.% C), heat treated to a near pearlitic microstructure with 5-10% pro-eutectoid ferrite. During the operation of freight trains, where block brakes are used, high thermal loads occur together with the high contact stresses, which combined can affect the mechanical properties of the material. In this study, the effects of annealing on local microstructure and mechanical properties in pearlitic railway wheel steel were investigated using electron microscopy and micro-hardness. It is found that after annealing at 650 degrees C, the room temperature hardness reduces about 25%, accompanied by significant spheroidization of cementite in the pearlitic colonies, though the size and the orientation gradients of the pearlitic colonies have not changed much. The relationship between the microstructural changes and the mechanical properties are discussed.
|
|
| 5. |
- Goel, Sneha, 1993-, et al.
(författare)
-
Effect of post-treatments under hot isostatic pressure on microstructural characteristics of EBM-built Alloy 718
- 2019
-
Ingår i: Additive Manufacturing. - : Elsevier BV. - 2214-8604 .- 2214-7810. ; 28, s. 727-737
-
Tidskriftsartikel (refereegranskat)abstract
- Electron beam melting (EBM) has emerged as an important additive manufacturing technique. In this study, Alloy 718 produced by EBM was investigated in as-built and post-treated conditions for microstructural characteristics and hardness. The post-treatments investigated were hot isostatic pressing (HIP) and combined HIP + heat treatment (HIP + HT) carried out as a single cycle inside the HIP vessel. Both the post-treatments resulted in significant decrease in defects inevitably present in the as-built material. The columnar grain structure of the as-built material was found to be maintained after post-treatment, with some sporadic localized grain coarsening noted. Although HIP led to complete dissolution of δ and γ′′ phase, stable NbC and TiN (occasionally present) particles were observed in the post-treated specimens. Significant precipitation of γ′′ phase was observed after HIP + HT, which was attributed to the two-step aging heat treatment carried out during HIP + HT. The presence of γ′′ phase or otherwise was correlated to the hardness of the material. While the HIP treatment resulted in drop in hardness, HIP + HT led to ‘recovery’ of the hardness to values exceeding those exhibited by the as-built material.
|
|
| 6. |
- Goel, Sneha, 1993-, et al.
(författare)
-
The Effect of Location and Post-treatment on the Microstructure of EBM-Built Alloy 718
- 2018
-
Ingår i: Proceedings of the 9th International Symposium on Superalloy 718 & Derivatives. - Cham : Springer. - 2367-1696 .- 2367-1181. - 9783319894799 - 9783319894805 ; , s. 115-129
-
Konferensbidrag (refereegranskat)abstract
- Additive manufacturing (AM) of Ni-based superalloys such as Alloy 718 may obviate the need for difficult machining and welding operations associated with geometrically intricate parts, thus potentially expanding design possibilities and facilitating cost-effective manufacture of complex components. However, processing AM builds completely free from defects, which may impair mechanical properties such as fatigue and ductility, is challenging. Anisotropic properties, microstructural heterogeneities and local formation of undesired phases are additional concerns that have motivated post-treatment of AM builds. This work investigates the microstructural changes associated with post-treatment of Alloy 718 specimens produced by Electron Beam Melting (EBM) for as-built microstructures at 3 build heights: near base plate, in the middle of build and near the top of the build. Two different post-treatment conditions, hot isostatic pressing (HIP) alone and a combined HIP with solutionising and two-step aging were examined and compared to the results for the as-built condition. The influence of various post-treatments on minor phase distributions (δ, γ″, carbides), overall porosity, longitudinal grain widths and Vickers microhardness was considered. The HIP treatment led to significant reduction in overall porosity and dissolution of δ phase, which led to appreciable grain growth for both post-treatment conditions. The variation in hardness noted as a function of build height for the as-built specimens was eliminated after post-treatment. Overall, the hardness was found to decrease after HIP and increase after the full HIP, solutionising and aging treatment, which was attributed to dissolution of γ″ during HIP and its re-precipitation in subsequent heat treatment steps.
|
|
| 7. |
- Jaladurgam, Nitesh Raj, 1993
(författare)
-
Heterogeneous deformation of multi-phase engineering materials - an in-situ neutron diffraction study
- 2019
-
Licentiatavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Gas turbines are complex power generation systems used in aerospace or land-based-power stations. Materials such as Ni-base superalloys are involved in the combustion zone of these machines, which continuously experiences harsh environments with loading at high temperatures. Moreover, the continuous demand for increasing operating temperature to achieve higher efficiencies and reduced emission levels opens the scene to new heat resistant materials like the state-of-the-art high entropy alloys (HEAs), which require a thorough understanding of the structure-process-property relationships. The microstructures of these advanced multi-phase, multi-component alloys are complex, and the deformation is generally heterogeneous both with respect to the different phases and to the crystallographic orientation within each phase. Hence, it is important to understand their behavior and performance during processing and service. In-situ neutron diffraction is a unique technique to probe the deformation behaviour during service/processing-like conditions, including plastic deformation at various temperatures, in order to provide insights into the structure-property relations. In the first part of this work the deformation mechanisms of a newly developed Ni-base superalloy was investigated using in-situ neutron diffraction and electron microscopy at room temperature. In addition, elasto-plastic self-consistent (EPSC) crystal plasticity simulations are used to obtain insights into the operating deformation mechanisms. In the second part, the as-cast eutectic high entropy alloy AlCoCrFeNi2.1 was studied using in-situ neutron diffraction at temperatures from 77 to 673 K. These investigations provide unique insights into the complex heterogeneous deformation behavior of these high-performance multi-phase engineering materials.
|
|
| 8. |
- Krakhmalev, Pavel, 1973-, et al.
(författare)
-
Influence of heat treatment under hot isostatic pressing (HIP) on microstructure of intermetallic-reinforced tool steel manufactured by laser powder bed fusion
- 2020
-
Ingår i: Materials Science & Engineering A: Structural Materials: Properties, Microstructure and Processing. - : Elsevier BV. - 0921-5093 .- 1873-4936. ; 772
-
Tidskriftsartikel (refereegranskat)abstract
- Microstructure and properties of as-built laser powder bed fusion (LPBF) steels differ from the conventional ones, and they may contain some porosity and lack of fusion. Therefore, post-treatments, including hot isostatic pressing (HIP), are used to density the material, and tailor the properties of the final product. Usually, HIP is performed as an operation separate from heat treatment. In the present investigation a new approach was used, in which the whole cycle of the heat treatment was carried out in HIP under pressure, and the influence of HIP on microstructure of an advanced stainless maraging tool steel manufactured by LPBF was investigated. For a comparison, a conventional steel grade of the same chemical composition, after a heat treatment at the same temperature-time conditions, was also characterized. The microstructure of the steel was investigated by means of advanced microscopy and atom probe tomography. The influence of the manufacturing route, heat treatment and HIP on microstructure, austenitic phase fraction and size distribution of precipitates was investigated, and the role of high pressure in stabilization of austenite in the microstructure was discussed. It was concluded that since HIP influences phase transformations, a fundamental understanding of the influence of HIP on microstructure is nececcary, and development of new post processing regimes guaranteeing the best performance of the material is required.
|
|
| 9. |
- Xu, Jinghao, et al.
(författare)
-
On the strengthening and embrittlement mechanisms of an additively manufactured Nickel-base superalloy
- 2020
-
Ingår i: Materialia. - : Elsevier BV. - 2589-1529. ; 10
-
Tidskriftsartikel (refereegranskat)abstract
- The γ′ phase strengthened Nickel-base superalloy is one of the most significant dual-phase alloy systems for high-temperature engineering applications. The tensile properties of laser powder-bed-fused IN738LC superalloy in the as-built state have been shown to have both good strength and ductility compared with its post-thermal treated state. A microstructural hierarchy composed of weak texture, sub-micron cellular structures and dislocation cellular walls was promoted in the as-built sample. After post-thermal treatment, the secondary phase γ′ precipitated with various size and fraction depending on heat treatment process. For room-temperature tensile tests, the dominated deformation mechanism is planar slip of dislocations in the as-built sample while dislocations bypassing the precipitates via Orowan looping in the γ′ strengthened samples. The extraordinary strengthening effect due to the dislocation substructure in the as-built sample provides an addition of 372 MPa in yield strength. The results of our calculation are in agreement with experimental yield strength for all the three different conditions investigated. Strikingly, the γ′ strengthened samples have higher work hardening rate than as-built sample but encounter premature failure. Experimental evidence shows that the embrittlement mechanism in the γ′ strengthened samples is caused by the high dislocation hardening of the grain interior region, which reduces the ability to accommodate further plastic strain and leads to premature intergranular cracking. On the basis of these results, the strengthening micromechanism and double-edge effect of strength and ductility of Nickel-base superalloy is discussed in detail.
|
|
| 10. |
- Åkerfeldt, Pia, et al.
(författare)
-
Electron backscatter diffraction characterization of fatigue crack growth in laser metal wire deposited Ti-6Al-4V
- 2018
-
Ingår i: Materials Characterization. - : Elsevier BV. - 1044-5803 .- 1873-4189. ; 135, s. 245-256
-
Tidskriftsartikel (refereegranskat)abstract
- By additive manufacturing (AM) there is a feasibility of producing near net shape components in basically one step from 3D CAD model to final product. The interest for AM is high and during the past decade a lot of research has been carried out in order to understand the influence from process parameters on the microstructure and furthermore on the mechanical properties. In the present study laser metal wire deposition of Ti-6Al-4V has been studied in detail with regard to its fatigue crack propagation characteristics. Two specimen orientations, parallel and perpendicular to the deposition direction, have been evaluated at room temperature and at 250 °C. No difference in the fatigue crack growth rate could be confirmed for the two specimen orientations. However, in the fractographic study it was observed that the tortuosity varied between certain regions on the fracture surface. The local crack path characteristic could be related to the alpha colony size and/or the crystallographic orientation. Moreover, large areas exhibiting similar crystallographic orientation were observed along the prior beta grain boundaries, which were attributed to the wide alpha colonies frequently observed along the prior beta grain boundaries. © 2017 Elsevier Inc.
|
|
| 11. |
- Hanning, Fabian, et al.
(författare)
-
The Effect of Grain Size on theSusceptibility Towards Strain Age Crackingof Wrought Haynes® 282®
- 2020
-
Ingår i: SPS 2020. - Amsterdam : IOS Press. - 9781643681467 - 9781643681474 ; 13, s. 407-416
-
Konferensbidrag (övrigt vetenskapligt/konstnärligt)abstract
- The effect of grain size on the suceptibility towards strain age cracking (SAC) has been investigated for Haynes® 282® in the tempeature range of 750 to 950°C after isothermal exposure up to 1800s. Grain growth was induced by heattreating the material at 1150°C for 2h, resulting in a fourfold increase in grain size. Hardness was significanlty reduced after heat treatment as compared to millannealed material. Large grain size resulted in intergranular fracture over a widertemperature range than small grain size material. Ductility was lowest at 850°C, while lower values were observed to be correlated to increased grain size. The rapid formation of grain boundary carbide networks in Haynes® 282® is found to be notable to compensate for higher local stresses on grain boundaries due to incresedgrain size.
|
|
| 12. |
- Qin, Xiao, 1993, et al.
(författare)
-
Microstructure and texture evolutions in FeCrAl cladding tube during pilger processing
- 2023
-
Ingår i: Journal of Materials Research and Technology. - 2238-7854. ; 25, s. 5506-5519
-
Tidskriftsartikel (refereegranskat)abstract
- The microstructure of FeCrAl cladding tubes depends on the fabricating process history. In this study, the microstructural characteristics of wrought FeCrAl alloys during industrial pilger processing into thin-walled tubes were investigated. The hot extruded tube showed ∼100 μm equiaxed grains with weak α∗-fiber in {h11}<1/h12> texture, while pilger rolling process change the microstructure to fragmented and elongated grains along the rolling direction. The pilgered textures could be predicted with the VPSC model. The inter-pass annealing at 800–850 °C for 1 h results in recovery and recrystallization of the ferric matrix and restoration of ductility. The final finished tube shows fine recrystallized grains (∼11 μm) with dominant γ-fiber in three dimensions. Pilger rolling enhanced α-fiber while annealing reduced α-fiber and enhanced γ-fiber. Microstructural evolution in the Laves precipitates followed the sequence of faceted needle-like → spherical → faceted ellipsoidal. Thermomechanical processing resulted in cladding tubes with an area fraction of ∼5% and a number density of 5 × 10−11 m−2 in Laves precipitates, which is half that of the first-pilgered tube. Laves precipitates pin the grain boundaries to control the microstructure and prevent grain coarsening.
|
|
| 13. |
- Shoja, Siamak, 1980
(författare)
-
Microstructure and plastic deformation of textured CVD alumina coatings
- 2020
-
Licentiatavhandling (övrigt vetenskapligt/konstnärligt)abstract
- It is known that the wear performance of α-alumina coatings produced by chemical vapor deposition (CVD) is significantly influenced by the type and degree of texture. However, the main reasons behind this behavior are not fully understood. This thesis contains studies of two related topics for increasing the understanding of α-alumina coatings. The first topic concerns the microstructure and texture development of CVD α-Al2O3 coatings, and the second topic concerns calculations and analysis of the Schmid factors ( m ) for coatings with different textures. By combining different analysis methods (such as XRD, SEM, FIB/SEM, TKD, TEM, STEM, XEDS), and theoretical and experimental Schmid factor analysis by MATLAB and EBSD, the microstructure and plastic deformation of α-alumina coatings were investigated. The microstructures of three different CVD α-Al2O3 layers deposited onto a Ti(C,N,O) bonding layer were studied. Grain boundary diffusion of heavy elements from the substrate to the bonding layer/α-Al2O3 interface was observed. This may be the cause of a disturbance in the early growth of α-Al2O3. Additionally, it was found that the number of interfacial pores at the bonding layer/α-Al2O3 interface increased by introducing the H2S gas. The H2S gas also promoted an earlier development of the (0001) texture. The orientation of the grains was developed to the desired texture both as a gradual change over several grains and as an abrupt transformation from one grain to another. The probability of plastic deformation in different wear zones on the rake face of a cutting tool was investigated theoretically and experimentally by analyzing Schmid factors for textured α-Al2O3 coatings. Schmid factor diagrams were constructed using MATLAB/MTEX and used to extract frequency distributions for different slip systems and textures. The results were compared with lateral distribution maps of Schmid factors obtained from experimental coatings. It was observed that basal slip is most easily activated in the transition zone, followed by prismatic slip systems 1 and 2 in coatings with an (0001)-texture. The homogeneous plastic deformation behavior observed in this coating is also connected to mostly high Schmid factors in the m -value distribution. The differences between the m -value distributions for the three slip systems are not that pronounced in the (01-12) and (11-20) textures, and the distributions are relatively wide. The low wear rate and more homogeneous deformation of the coating with (0001) texture compared to the other coating textures may be the result of the high plasticity, offered by the easy activation of basal slip and prismatic 1 slip, and the low spread of Schmid factor values at the transition zone. In conclusion, the results presented in this thesis form a knowledge platform that can be used to understand the microstructure and wear mechanisms of textured CVD α-alumina coatings.
|
|
| 14. |
- Krakhmalev, Pavel, 1973-, et al.
(författare)
-
Microstructure, solidification texture, and thermal stability of 316 L stainless steel manufactured by laser powder bed fusion
- 2018
-
Ingår i: Metals. - : MDPI AG. - 2075-4701. ; 8:8, s. 1-18
-
Tidskriftsartikel (refereegranskat)abstract
- This article overviews the scientific results of the microstructural features observed in 316 L stainless steel manufactured by the laser powder bed fusion (LPBF) method obtained by the authors, and discusses the results with respect to the recently published literature. Microscopic features of the LPBF microstructure, i.e., epitaxial nucleation, cellular structure, microsegregation, porosity, competitive colony growth, and solidification texture, were experimentally studied by scanning and transmission electron microscopy, diffraction methods, and atom probe tomography. The influence of laser power and laser scanning speed on the microstructure was discussed in the perspective of governing the microstructure by controlling the process parameters. It was shown that the three-dimensional (3D) zig-zag solidification texture observed in the LPBF 316 L was related to the laser scanning strategy. The thermal stability of the microstructure was investigated under isothermal annealing conditions. It was shown that the cells formed at solidification started to disappear at about 800 °C, and that this process leads to a substantial decrease in hardness. Colony boundaries, nevertheless, were quite stable, and no significant grain growth was observed after heat treatment at 1050 °C. The observed experimental results are discussed with respect to the fundamental knowledge of the solidification processes, and compared with the existing literature data.
|
|
| 15. |
- Saarimäki, Jonas, et al.
(författare)
-
3D Residual Stresses in Selective Laser Melted Hastelloy X
- 2017
-
Ingår i: Residual Stresses 2016: ICRS-10, Materials Research Proceedings 2 (2016). - : Materials Research Forum LLC. ; , s. 73-78
-
Konferensbidrag (refereegranskat)abstract
- 3D residual stresses in as manufactured EOS NickelAlloy HX, produced by laser powder bed additive manufacturing, are analysed on the surface closest to the build-plate. Due to the severe thermal gradient produced during the melting and solidification process, profound amounts of thermal strains are generated. Which can result in unwanted geometrical distortion and effect the mechanical properties of the manufactured component. Measurements were performed using a four-circle goniometer Seifert X-ray machine, equipped with a linear sensitive detector and a Cr-tube. Evaluation of the residual stresses was conducted using sin2ψ method of the Ni {220} diffraction peak, together with material removal technique to obtain in-depth profiles. An analysis of the material is reported. The analysis reveals unwanted residual stresses, and a complicated non-uniform grain structure containing large grains with multiple low angle grain boundaries together with nano-sized grains. Grains are to a large extent, not equiaxed, but rather elongated.
|
|
| 16. |
- Andersson, Anton, et al.
(författare)
-
Ground granulated iron silicate slag as supplementary cementitious material: Effect of prolonged grinding and granulation temperature
- 2023
-
Ingår i: Cleaner Materials. - : Elsevier. - 2772-3976. ; 10
-
Tidskriftsartikel (refereegranskat)abstract
- The metallurgical and cement industries contribute significantly to anthropogenic carbon dioxide emissions. Utilizing oxidic by-products from the metallurgical industry as supplementary cementitious materials (SCMs) can improve resource efficiency and reduce emissions from cement production. Iron silicate copper slags have been studied as SCMs, but mainly in systems where Portland cement is used as an activator. There is limited research on the inherent reactivity of the slag under changing processing conditions. The present study offers insight into the effect of granulation temperature and grinding on the inherent reactivity of an industrially produced iron silicate copper slag. The results showed that granulation temperature had an insignificant effect on reactivity, while grinding generated substantial improvements. The latter effect was concluded to stem from the increased specific surface area, increased number of sites for nucleation and growth of hydrates, and changes in the inherent reactivity owing to structural changes induced by the grinding.
|
|
| 17. |
- Cabo Rios, Alberto, 1990
(författare)
-
Experimental study and simulation of sintering of 316L components produced by binder jetting
- 2023
-
Licentiatavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Binder Jetting (BJT) is a multi-step Additive Manufacturing (AM) technique that is used for producing components with highly complex geometries and competitive final properties with high productivity when compared to other AM technologies. The first step provides the basic part geometric shape (BJT printing), and the next step (debinding and sintering) consolidates the part to reach final geometry and intended basic material properties. Due to the low density of green BJT components after printing (~50-60%), significant shrinkage (~20%) occurs during the sintering process along different directions. Also, sintering may lead to distortion of the external shape of the components. During BJT printing, the powder is being deposited layer-by-layer and binder is selectively placed to create a 3D geometry. Therefore, the metal particle’s arrangement of the green BJT components is influenced by the layer-by-layer buildup nature of the printing process. This impacts the behavior of the components during the debinding and sintering process. The first part of this study aims to develop the understanding of densification development during the sintering of 316L stainless-steel BJT samples. The intensity of the dimensional evolution anisotropy was characterized by multi-axial dilatometry experiments. Measured shrinkages were up to 15% higher along the building direction, while minor variation was found between the other two orthogonal directions. Only small shrinkages (<0.5%) were observed during debinding without significant anisotropy. A rapid increase of the shrinkage rate was observed at high temperature (~1310°C), related to the formation of δ-ferrite phase. This boost of densification is critical to achieve high densities (96-99%) of 316L BJT sintered components. The second part consists of the microstructural evolution analysis. The EBSD phase maps showed the formation of δ-ferrite at temperatures >1300°C. The porosity characterization within different cross-sections demonstrated that some anisotropic distribution of porosity may be developed during sintering. The last part of this study introduces the application of the continuum theory of sintering for modelling the sintering behavior of 316L BJT components. The identification of model parameters was done from dilatometry data. Then, a new material viscosity expression was proposed to account for the effect of δ-ferrite transformation. The model was proved to accomplish good predictions of the density evolution during sintering of BJT samples.
|
|
| 18. |
- Chasoglou, Dimitris, 1982, et al.
(författare)
-
Effect of reducing agents on the sintering of chromium alloyed PM steels
- 2013
-
Ingår i: Proceedings EURO PM2013 Congress & Exhibition, 15-18 September 2013, Gothenburg, Sweden. - : European Powder Metallurgy Association (EPMA). ; 2, s. 297-302
-
Konferensbidrag (refereegranskat)abstract
- The control of the surface chemistry during sintering is the key factor for the successful and efficientproduction of PM parts, especially for powders containing elements with high affinity to oxygen such as chromium.The effect of different reducing agents was investigated by performing sintering trials on water atomized steel powder pre-alloyed with 3 wt.% Cr with and without the addition of graphite as well as using atmospheres with varying hydrogen content. The use of thermal analysis and photoacoustic spectroscopy in combination with results from fractographic investigation showed that oxide reduction is enhanced with the presence of hydrogen even if the main reduction mechanism is the carbothermal reactions. Oxides rich in Cr, Mn and Si were formed during sintering for all appliedconditions. The findings are summarized in a simple model describing the enclosure of oxides during the sinter-neckdevelopment and the changes in surface chemistry during the process.
|
|
| 19. |
- Chasoglou, Dimitris, 1982, et al.
(författare)
-
Optimisation of sintering atmospheres for controlled sintering of PM steels
- 2013
-
Ingår i: Proceedings EURO PM2013 Congress & Exhibition, 15-18 September 2013, Gothenburg, Sweden. - : European Powder Metallurgy Association (EPMA). ; 2, s. 339-346
-
Konferensbidrag (refereegranskat)abstract
- The use of elements with high oxygen affinity such as Cr or Mn in PM steels has been met with skepticism although such grades are attractive options for structural applications. They require strict control of the used atmosphere during the sintering process. Various techniques such asphotoacoustic spectroscopy (PAS) and continuous CO/CO2/H2O measurements have been implemented for atmosphere monitoring during sintering trials of Cr-alloyed steel powder. The used atmospheres were nitrogen-hydrogen blends (0,3,10 and 100% H2) as well as vacuum. The progress of the oxidation/reduction processes was also followed with thermogravimetric studies. The pressed and sintered samples were examined using optical and electron microscopy in combination with EDX in order to evaluate the formed reaction products. The presence of hydrogen, even in smallamounts, is positive for the oxide reduction. Results show that careful adjustment of the used atmosphere leads to efficient production of steel components based on Cr -prealloyed powders.
|
|
| 20. |
- Chen, Zhe, et al.
(författare)
-
Surface Integrity and Structural Stability of Broached Inconel 718 at High Temperatures
- 2016
-
Ingår i: Metallurgical and Materials Transactions. A. - : Springer. - 1073-5623 .- 1543-1940. ; 47A:7, s. 3664-3676
-
Tidskriftsartikel (refereegranskat)abstract
- The current study focused on the surface integrity issues associated with broaching of Inconel 718 and the structural stability of the broached specimen at high temperatures, mainly involving the microstructural changes and residual stress relaxation. The broaching operation was performed using similar cutting conditions as that used in turbo machinery industries for machining fir-tree root fixings on turbine disks. Thermal exposure was conducted at 723 K, 823 K, and 923 K (450 A degrees C, 550 A degrees C, and 650 A degrees C) for 30, 300, and 3000 hours, respectively. Surface cavities and debris dragging, sub-surface cracks, high intensity of plastic deformation, as well as the generation of tensile residual stresses were identified to be the main issues in surface integrity for the broached Inconel 718. When a subsequent heating was applied, surface recrystallization and alpha-Cr precipitation occurred beneath the broached surface depending on the applied temperature and exposure time. The plastic deformation induced by the broaching is responsible for these microstructural changes. The surface tension was completely relaxed in a short time at the temperature where surface recrystallization occurred. The tensile layer on the sub-surface, however, exhibited a much higher resistance to the stress relief annealing. Oxidation is inevitable at high temperatures. The study found that the surface recrystallization could promote the local Cr diffusion on the broached surface.
|
|
| 21. |
- Dimitrios, Nikas, et al.
(författare)
-
Evaluation of local strength via microstructural quantification in a pearlitic rail steel deformed by simultaneous compression and torsion
- 2018
-
Ingår i: Materials Science & Engineering. - : Elsevier. - 0921-5093 .- 1873-4936. ; 737, s. 341-347
-
Tidskriftsartikel (refereegranskat)abstract
- Pearlitic steels are commonly used for railway rails because they combine good strength and wear properties. During service, the passage of trains results in large accumulation of shear strains in the surface layer of the rail, sometimes leading to crack initiation. Knowledge of the material properties versus the shear strain in this layer is therefore important for fatigue life predictions. In this study, fully pearlitic R260 rail steel was deformed using a bi-axial torsion-compression machine to reach different shear strains. Microstructural parameters including interlamellar spacing, thickness of ferrite and cementite lamellae and dislocation density in the ferrite lamellae, as well as hardness were quantitatively characterized at different shear strain levels. Based on the microstructural observations and the quantification of the microstructural parameters, the local flow stresses were estimated based on boundary strengthening and dislocation strengthening models. A good agreement was found between the estimated flow stresses and the flow stresses determined from microhardness measurements. d
|
|
| 22. |
- Dimitrios, Nikas, et al.
(författare)
-
Mechanical properties and fatigue behavior of railway wheel steels as influenced by mechanical and thermal loadings
- 2015
-
Ingår i: CM 2015 - 10th International Conference on Contact Mechanics of Wheel / Rail Systems. - : International Conference on Contact Mechanics of Wheel / Rail Systems. ; 366:SI, s. 407-415
-
Konferensbidrag (refereegranskat)abstract
- In the current work the deterioration of mechanical properties of railway wheel steels (UIC ER7T and ER8T) is in focus. These are medium carbon steels (∼0.55 wt.% C) heat treated to a near pearlitic microstructure with some 5-10% pro-eutectoid ferrite. During operation of trains, high thermal loads are evolved because of recurring acceleration, braking, curving and occasional slippage. It is thus relevant to examine the high temperature performance of wheel material and evaluate the decrease in strength after thermal exposure as well as the degradation of fatigue properties. Samples were extracted from virgin wheels and pre-strained to around 6.5% strain as well as cyclically deformed, to also account for the change in properties that is induced by plastic deformation inherent in the wheel tread surface. Both un-deformed and pre-strained material was heat treated for different times in the temperature range of interest, from 250°C to 600-700°C. Hardening was observed in both conditions around 300°C followed by softening at higher temperatures. Spheroidization of the pearlite started to become visible at 450°C for the un-deformed material and at around 400°C for the pre-strained.
|
|
| 23. |
|
|
| 24. |
- Guldris Leon, Lorena, 1983, et al.
(författare)
-
Understanding Mineral Liberation during Crushing Using Grade-by-Size Analysis - A Case Study of the Penuota Sn-Ta Mineralization, Spain
- 2020
-
Ingår i: Minerals. - : MDPI AG. - 2075-163X. ; 10:2
-
Tidskriftsartikel (refereegranskat)abstract
- Coarse comminution test-work and modeling are powerful tools in the design and optimization of mineral processing plants and provide information on energy consumption. Additional information on mineral liberation characteristics can be used for assessing the potential of pre-concentration stages or screens in the plant design. In ores of high-value metals (e.g., Ta, W), standard techniques-such as the mineralogical quantification of grain mounts by quantitative evaluation of minerals by scanning electron microscopy (QEMSCAN) or chemical analysis by X-ray fluorescence (XRF) can be challenging, due to the low relative abundance of such valuable minerals. The cost of QEMSCAN is also a limiting factor, especially considering the large number of samples required for the optimization of coarse comminution. In this study, we present an extended analytical protocol to a well-established mechanical test of interparticle breakage to improve the assessment of coarse mineral liberation characteristics. The liberation of ore minerals is a function of the rock texture and the difference in size and mechanical properties of the valuable minerals relative to gangue minerals and they may fraction in certain grain sizes if they behave differently during comminution. By analyzing the bulk-chemistry of the different grain size fractions produced after compressional testing, and by generating element by size diagrams, it is possible to understand the liberation characteristics of an ore. We show, based on a case study performed on a tantalum ore deposit, that element distribution can be used to study the influence of mechanical parameters on mineral liberation. This information can direct further mineralogical investigation and test work.
|
|
| 25. |
- Hedström, Peter, et al.
(författare)
-
Load partitioning between single bulk grains in a two-phase duplex stainless steel during tensile loading
- 2010
-
Ingår i: Acta Materialia. - : Elsevier BV. - 1359-6454 .- 1873-2453. ; 58:2, s. 734-744
-
Tidskriftsartikel (refereegranskat)abstract
- The lattice strain tensor evolution for single bulk grains of austenite and ferrite in a duplex stainless steel during tensile loading to 0.02 applied strain has been investigated using in situ high-energy X-ray measurements and finite-element modeling. Single-grain X-ray diffraction lattice strain data for the eight austenite and seven ferrite grains measured show a large variation of residual lattice strains, which evolves upon deformation to the point where some grains with comparable crystallographic orientations have lattice strains different by 1.5 x 10(-3), corresponding to a stress of similar to 300 MPa. The finite-element simulations of the 15 measured grains in three different spatial arrangements confirmed the complex deformation constraint and importance of local grain environment.
|
|
