| 1. |
- Buckland, Philip I., 1973-, et al.
(författare)
-
The Strategic Environmental Archaeology Database : a resource for international, multiproxy and transdisciplinary studies of environmental and climatic change
- 2015
-
Konferensbidrag (refereegranskat)abstract
- Climate and environmental change are global challenges which require global data and infrastructure to investigate. These challenges also require a multi-proxy approach, integrating evidence from Quaternary science and archaeology with information from studies on modern ecology and physical processes among other disciplines. The Strategic Environmental Archaeology Database (SEAD http://www.sead.se) is a Swedish based international research e-infrastructure for storing, managing, analysing and disseminating palaeoenvironmental data from an almost unlimited number of analysis methods. The system currently makes available raw data from over 1500 sites (>5300 datasets) and the analysis of Quaternary fossil insects, plant macrofossils, pollen, geochemistry and sediment physical properties, dendrochronology and wood anatomy, ceramic geochemistry and bones, along with numerous dating methods. This capacity will be expanded in the near future to include isotopes, multi-spectral and archaeo-metalurgical data. SEAD also includes expandable climate and environment calibration datasets, a complete bibliography and extensive metadata and services for linking these data to other resources. All data is available as Open Access through http://qsead.sead.se and downloadable software. SEAD is maintained and managed at the Environmental Archaeology Lab and HUMlab at Umea University, Sweden. Development and data ingestion is progressing in cooperation with The Laboratory for Ceramic Research and the National Laboratory for Wood Anatomy and Dendrochronology at Lund University, Sweden, the Archaeological Research Laboratory, Stockholm University, the Geoarchaeological Laboratory, Swedish National Historical Museums Agency and several international partners and research projects. Current plans include expanding its capacity to serve as a data source for any system and integration with the Swedish National Heritage Board's information systems. SEAD is partnered with the Neotoma palaeoecology database (http://www.neotomadb.org) and a new initiative for building cyberinfrastructure for transdisciplinary research and visualization of the long-term human ecodynamics of the North Atlantic funded by the National Science Foundation (NSF).
|
|
| 2. |
- Åkerfeldt, Pia, et al.
(författare)
-
Electron backscatter diffraction characterization of fatigue crack growth in laser metal wire deposited Ti-6Al-4V
- 2018
-
Ingår i: Materials Characterization. - : Elsevier BV. - 1044-5803 .- 1873-4189. ; 135, s. 245-256
-
Tidskriftsartikel (refereegranskat)abstract
- By additive manufacturing (AM) there is a feasibility of producing near net shape components in basically one step from 3D CAD model to final product. The interest for AM is high and during the past decade a lot of research has been carried out in order to understand the influence from process parameters on the microstructure and furthermore on the mechanical properties. In the present study laser metal wire deposition of Ti-6Al-4V has been studied in detail with regard to its fatigue crack propagation characteristics. Two specimen orientations, parallel and perpendicular to the deposition direction, have been evaluated at room temperature and at 250 °C. No difference in the fatigue crack growth rate could be confirmed for the two specimen orientations. However, in the fractographic study it was observed that the tortuosity varied between certain regions on the fracture surface. The local crack path characteristic could be related to the alpha colony size and/or the crystallographic orientation. Moreover, large areas exhibiting similar crystallographic orientation were observed along the prior beta grain boundaries, which were attributed to the wide alpha colonies frequently observed along the prior beta grain boundaries. © 2017 Elsevier Inc.
|
|
| 3. |
|
|
| 4. |
- Åkerfeldt, Maria, 1982, et al.
(författare)
-
Textile piezoelectric sensors – melt spun bi-component poly(vinylidene fluoride) fibres with conductive cores and poly(3,4-ethylene dioxythiophene)-poly(styrene sulfonate) coating as the outer electrode
- 2014
-
Ingår i: Fashion and Textiles. - : Springer Science and Business Media LLC. - 2198-0802. ; 1:1
-
Tidskriftsartikel (refereegranskat)abstract
- The work presented here addresses the outer electroding of a fully textile piezoelectric strain sensor, consisting of bi-component fibre yarns of β-crystalline poly(vinylidene fluoride) (PVDF) sheath and conductive high density polyethylene (HDPE)/carbon black (CB) core as insertions in a woven textile, with conductive poly(3,4-ethylene dioxythiophene)-poly(styrene sulfonate) (PEDOT:PSS) coatings developed for textile applications. Two coatings, one with a polyurethane binder and one without, were compared for the application and evaluated as electrode material in piezoelectric testing, as well as tested for surface resistivity, tear strength, abrasion resistance and shear flexing. Both coatings served their function as the outer electrodes in the system and no difference in this regard was detected between them. Omission of the binder resulted in a surface resistivity one order of magnitude less, of 12.3 Ω/square, but the surface resistivity of these samples increased more upon abrasion than the samples coated with binder. The tear strength of the textile coated with binder decreased with one third compared to the uncoated substrate, whereas the tear strength of the coated textile without binder increased with the same amount. Surface resistivity measurements and scanning electron microscopy (SEM) images of the samples subjected to shear flexing showed that the coatings without the binder did not withstand this treatment, and that the samples with the binder managed this to a greater extent. In summary, both of the PEDOT:PSS coatings could be used as outer electrodes of the piezoelectric fibres, but inclusion of binder was found necessary for the durability of the coating.
|
|
| 5. |
- Chen, Zhe, et al.
(författare)
-
Nano-scale characterization of white layer in broached Inconel 718
- 2017
-
Ingår i: Materials Science & Engineering A: Structural Materials: Properties, Microstructure and Processing. - Amsterdam : Elsevier BV. - 0921-5093 .- 1873-4936. ; 684, s. 373-384
-
Tidskriftsartikel (refereegranskat)abstract
- The formation mechanism of white layers during broaching and their mechanical properties are not well investigated and understood to date. In the present study, multiple advanced characterization techniques with nano-scale resolution, including transmission electron microscopy (TEM), transmission Kikuchi diffraction (TKD), atom probe tomography (APT) as well as nano-indentation, have been used to systematically examine the microstructural evolution and corresponding mechanical properties of a surface white layer formed when broaching the nickel-based superalloy Inconel 718.TEM observations showed that the broached white layer consists of nano-sized grains, mostly in the range of 20–50 nm. The crystallographic texture detected by TKD further revealed that the refined microstructure is primarily caused by strong shear deformation. Co-located Al-rich and Nb-rich fine clusters have been identified by APT, which are most likely to be γ′ and γ′′ clusters in a form of co-precipitates, where the clusters showed elongated and aligned appearance associated with the severe shearing history. The microstructural characteristics and crystallography of the broached white layer suggest that it was essentially formed by adiabatic shear localization in which the dominant metallurgical process is rotational dynamic recrystallization based on mechanically-driven subgrain rotations. The grain refinement within the white layer led to an increase of the surface nano-hardness by 14% and a reduction in elastic modulus by nearly 10% compared to that of the bulk material. This is primarily due to the greatly increased volume fraction of grain boundaries, when the grain size was reduced down to the nanoscale.
|
|
| 6. |
- Dimitrios, Nikas, et al.
(författare)
-
Effect of annealing on microstructure in railway wheel steel
- 2022
-
Ingår i: 42Nd Riso International Symposium On Materials Science. - : Institute of Physics Publishing (IOPP). ; 1249
-
Konferensbidrag (refereegranskat)abstract
- Railway wheels are commonly made from medium carbon steels (similar to 0.55 wt.% C), heat treated to a near pearlitic microstructure with 5-10% pro-eutectoid ferrite. During the operation of freight trains, where block brakes are used, high thermal loads occur together with the high contact stresses, which combined can affect the mechanical properties of the material. In this study, the effects of annealing on local microstructure and mechanical properties in pearlitic railway wheel steel were investigated using electron microscopy and micro-hardness. It is found that after annealing at 650 degrees C, the room temperature hardness reduces about 25%, accompanied by significant spheroidization of cementite in the pearlitic colonies, though the size and the orientation gradients of the pearlitic colonies have not changed much. The relationship between the microstructural changes and the mechanical properties are discussed.
|
|
| 7. |
- Lindberg, Siv M, et al.
(författare)
-
A product semantic study of the influence of the sense of touch on the evaluation of wood-based materials
- 2013
-
Ingår i: Materials & design. - : Elsevier BV. - 0264-1275 .- 1873-4197 .- 0261-3069. ; 52, s. 300-307
-
Tidskriftsartikel (refereegranskat)abstract
- Based on product semantics, this study investigated how the tactile attributes of wood and wood-based composites are perceived and interpreted semantically. The wood-based samples included ash, birch, elm, oak, pine, OSB (oriented strand board), two wood pulp-reinforced polylactide composites, Comp A and B and one wood-fiber reinforced polypropene composite, Comp C. The subjects rated the samples by the descriptive words natural, exclusive, eco-. friendly, rough, inexpensive, reliable, warm, modern, snug and solid. The most significant differences between the samples were found for roughness and for the descriptors, reliable, natural and solid. A principal component analysis yielded three attributes based on the tactile perceptions: reliable, old-. fashioned and smooth. The solid wood pieces were perceived as natural and oak was perceived as being exclusive. The composite materials presented a greater variation in terms of perceived attributes than the wood specimens.
|
|
| 8. |
- Mahade, Satyapal, 1987-, et al.
(författare)
-
Incorporation of graphene nano platelets in suspension plasma sprayed alumina coatings for improved tribological properties
- 2021
-
Ingår i: Applied Surface Science. - : Elsevier BV. - 0169-4332 .- 1873-5584. ; 570
-
Tidskriftsartikel (refereegranskat)abstract
- Graphene possesses high fracture toughness and excellent lubrication properties, which can be exploited to enhance tribological performance of coating systems utilized to combat wear. In this work, suspension plasma spray (SPS) process was employed to deposit a composite, graphene nano-platelets (GNP) incorporated alumina coating. For comparison, monolithic alumina was also deposited utilizing identical spray conditions. The as-deposited coatings were characterized in detail for their microstructure, porosity content, hardness, fracture toughness and phase composition. Raman analysis of the as-deposited composite coating confirmed retention of GNP. The composite coating also showed good microstructural integrity, comparable porosity, higher fracture toughness and similar alumina phase composition as the monolithic alumina coating. The as-deposited coatings were subjected to dry sliding wear tests. The GNP incorporated composite coating showed lower CoF and lower specific wear rate than the pure alumina coating. Additionally, the counter surface also showed a lower wear rate in case of the composite coating. Post-wear analysis performed by SEM/EDS showed differences in the coating wear track and in the ball wear track of monolithic and composite coatings. Furthermore, Raman analysis in the wear track of composite coating confirmed the presence of GNP. The micro-indentation and wear test results indicate that the presence of GNP in the composite coating aided in improving fracture toughness, lowering CoF and specific wear rate compared to the monolithic coating. Results from this work demonstrated retention of GNP in an SPS processed coating, which can be further exploited to design superior wear-resistant coatings.
|
|
| 9. |
- Sefer, Birhan, 1983-, et al.
(författare)
-
Chemical Milling of Cast Ti-6Al-4V and Ti-6Al-2Sn-4Zr-2Mo Alloys in Hydrofluoric-Nitric Acid Solutions
- 2017
-
Ingår i: Corrosion. - : Association for Materials Protection and Performance (AMPP). - 0010-9312 .- 1938-159X. ; 73:4, s. 394-407
-
Tidskriftsartikel (refereegranskat)abstract
- The behavior of cast Ti-6Al-4V and Ti-6Al-2Sn-4Zr-2Mo during chemical milling in hydrofluoric-nitric (HF-HNO3) acid solutions with 1:3 and 1:11 molar ratios was investigated using electrochemical and atomic force microscopy (AFM) techniques. Faster corrosion rate in 1:3 solutions was measured for Ti-6Al-4V than for Ti-6Al-2Sn-4Zr-2Mo, whereas in 1:11 solution Ti-6Al-2Sn-4Zr-2Mo exhibited higher corrosion rate. Scanning Kelvin probe force microscopy measurements revealed difference in the Volta potential between the α-laths and the β-layers in the Widmansttäten microstructure indicating operation of microgalvanic cells between the microconstituents when in contact with HF-HNO3 solution. The AFM topography measurements demonstrated faster corrosion of the α-laths compared to the β-layers, in both alloys. In 1:3 solutions, higher α/β height difference was measured in Ti-6Al-4V, whereas in 1:11 solution, the difference was higher in Ti-6Al-2Sn-4Zr-2Mo. The results revealed that the chemical milling behavior of the two investigated alloys is controlled by the microscopic corrosion behavior of the individual microconstituents.
|
|
| 10. |
|
|
| 11. |
- Grolig, Jan Gustav, 1986
(författare)
-
Coated Ferritic Stainless Steels as Interconnects in Solid Oxide Fuel Cells - Material Development and Electrical Properties
- 2015
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Solid oxide fuel cells (SOFCs) are attracting increasing interest as devices with potentialuses in decentralized and clean electricity and heat production. Several challengeswith respect to materials have to be overcome to achieve efficiencies and life-spansthat are sufficient for long-term applications.An important element of an SOFC stack is the interconnect component, which connectstwo adjacent fuel cell elements. Interconnects, which are commonly composedof ferritic stainless steels, have to be corrosion-resistant, mechanically stable and costoptimized.This work aimed to investigate economic solutions for interconnect materials and tounderstand the underlying mechanisms of degradation and electrical conduction ofthese materials. Mainly two substrates, a commercially available steel (AISI 441) anda ferritic stainless steel that was optimized for an SOFC application (Sandvik SanergyHT) were combined with different barrier coatings and exposed to a cathode-sideatmosphere. A method was developed that allows for the electrical characterizationof promising material systems and model alloys, thereby facilitating a fundamentalunderstanding of the dominant electrical conduction processes linked to the oxidescales that grow on interconnects. The AISI 441 steel coated with reactive elementsand cobalt showed good corrosion and chromium evaporation profiles, while AISI 441coated with cerium and cobalt also had promising electrical properties. The SanergyHT steel was examined with coatings of copper and iron and copper and manganese,respectively. The corrosion and chromium evaporation profiles of Sanergy HT wereimproved by coating with copper and iron. The copper and iron-coated Sanergy HTshowed lower area specific resistance values than cobalt-coated Sanergy HT. Chromia,which is the main constituent of oxide scales, was synthesized using differentmethods. The electrical properties of chromia were found to be sensitive to not onlyimpurities, but also heat treatment. Finally the electrical properties of cobalt- andcobalt cerium-coated Sanergy HT steels were investigated. It was revealed that theaddition of cerium improved the conductivity of the interconnect by both slowingdown chromia growth and preventing the outward diffusion of iron into the spinel.
|
|
| 12. |
- Neikter, Magnus, et al.
(författare)
-
Microstructure and Defects in Additive Manufactured Titanium : a Comparison Between Microtomography and Optical Microscopy
- 2017
-
Konferensbidrag (övrigt vetenskapligt/konstnärligt)abstract
- The aim of this work has been to compare two different analysing methods; x-ray microtomography and light optical microscopy, when it comes to defects and microstructure of additively manufactured Ti-6Al-4V. The results show that both techniques have their pros and cons:microtomography is the preferred choice for defect detection by analysing the full 3D sample volume, while light optical microscopy is better for analysing finer details in 2D.
|
|
| 13. |
- Krakhmalev, Pavel, 1973-, et al.
(författare)
-
Microstructure, solidification texture, and thermal stability of 316 L stainless steel manufactured by laser powder bed fusion
- 2018
-
Ingår i: Metals. - : MDPI AG. - 2075-4701. ; 8:8, s. 1-18
-
Tidskriftsartikel (refereegranskat)abstract
- This article overviews the scientific results of the microstructural features observed in 316 L stainless steel manufactured by the laser powder bed fusion (LPBF) method obtained by the authors, and discusses the results with respect to the recently published literature. Microscopic features of the LPBF microstructure, i.e., epitaxial nucleation, cellular structure, microsegregation, porosity, competitive colony growth, and solidification texture, were experimentally studied by scanning and transmission electron microscopy, diffraction methods, and atom probe tomography. The influence of laser power and laser scanning speed on the microstructure was discussed in the perspective of governing the microstructure by controlling the process parameters. It was shown that the three-dimensional (3D) zig-zag solidification texture observed in the LPBF 316 L was related to the laser scanning strategy. The thermal stability of the microstructure was investigated under isothermal annealing conditions. It was shown that the cells formed at solidification started to disappear at about 800 °C, and that this process leads to a substantial decrease in hardness. Colony boundaries, nevertheless, were quite stable, and no significant grain growth was observed after heat treatment at 1050 °C. The observed experimental results are discussed with respect to the fundamental knowledge of the solidification processes, and compared with the existing literature data.
|
|
| 14. |
- Hosseini, Seyedehsan, 1994
(författare)
-
Additive-Driven Improvements in Interfacial Properties and Processing of TMP-Polymer Composites
- 2023
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Efforts to address environmental concerns have resulted in new regulations designed to plan the reduction of plastic and synthetic polymer usage, necessitating the search for sustainable natural alternatives with comparable cost-effectiveness and mechanical performance. Thermomechanical pulp (TMP) fibres are one of the most affordable natural fibres that have no chemical refining in production, production have a high yield of 90-98% and TMP fibres have been demonstrated to improve the mechanical characteristics (strength, stiffness and toughness) of wood-polymer composites (WPCs) compared to the pure polymer. The integration of TMP fibres with non-polar synthetic polymers remains a challenge due to surface polarity differences. This PhD thesis aims to ease the processing of TMP fibre composites through the incorporation of additives. The hypothesis posits that incorporating magnesium stearate (MgSt), molybdenum disulfide (MoS2) and alkyl ketene dimer (AKD) as additives in TMP composites will enhance interfacial properties, resulting in improved processability and flow behaviour at high temperatures. MoS2 is known for its interaction with lignin, which exists in TMP and MgSt is recognised for its ability to improve flow in pharmaceutical processing when combined with cellulose, also a component of TMP. AKD modifies the hydrophilic properties of lignocellulosic surfaces. The experimental work explores the effect of these additives on the properties of TMP composites of ethylene acrylic acid copolymer (EAA) and polypropylene (PP) matrices. The dynamic mechanical analysis (DMA) and mechanical analysis results reveal that MoS2 exhibits superior interaction with TMP fibres, yielding enhanced interfacial properties compared to MgSt in between EAA and TMP fibres. Rheological studies elucidate the transition from a fluid-like state to a network-like structure upon the incorporation of TMP into the PP matrix. The incorporation of AKD with C18 reduces the viscosity of TMP-PP composites and PP itself, and, as determined through theoretical Hansen solubility parameter (HSP) calculations, increases compatibility between cellulose in TMP fibres and PP. The addition of AKD influences both the colour (lighter) and shape (smoother surface) of the extrudate filaments in the TMP-PP composites, indicative of improved processing. In addition, frictional analysis demonstrates the reduction of the coefficient of friction (COF) between metal and TMP fibre by MgSt and AKD treatments.
|
|
| 15. |
- Goel, Sneha, 1993-, et al.
(författare)
-
Effect of post-treatments under hot isostatic pressure on microstructural characteristics of EBM-built Alloy 718
- 2019
-
Ingår i: Additive Manufacturing. - : Elsevier BV. - 2214-8604 .- 2214-7810. ; 28, s. 727-737
-
Tidskriftsartikel (refereegranskat)abstract
- Electron beam melting (EBM) has emerged as an important additive manufacturing technique. In this study, Alloy 718 produced by EBM was investigated in as-built and post-treated conditions for microstructural characteristics and hardness. The post-treatments investigated were hot isostatic pressing (HIP) and combined HIP + heat treatment (HIP + HT) carried out as a single cycle inside the HIP vessel. Both the post-treatments resulted in significant decrease in defects inevitably present in the as-built material. The columnar grain structure of the as-built material was found to be maintained after post-treatment, with some sporadic localized grain coarsening noted. Although HIP led to complete dissolution of δ and γ′′ phase, stable NbC and TiN (occasionally present) particles were observed in the post-treated specimens. Significant precipitation of γ′′ phase was observed after HIP + HT, which was attributed to the two-step aging heat treatment carried out during HIP + HT. The presence of γ′′ phase or otherwise was correlated to the hardness of the material. While the HIP treatment resulted in drop in hardness, HIP + HT led to ‘recovery’ of the hardness to values exceeding those exhibited by the as-built material.
|
|
| 16. |
- Goel, Sneha, 1993-, et al.
(författare)
-
The Effect of Location and Post-treatment on the Microstructure of EBM-Built Alloy 718
- 2018
-
Ingår i: Proceedings of the 9th International Symposium on Superalloy 718 & Derivatives. - Cham : Springer. - 2367-1696 .- 2367-1181. - 9783319894799 - 9783319894805 ; , s. 115-129
-
Konferensbidrag (refereegranskat)abstract
- Additive manufacturing (AM) of Ni-based superalloys such as Alloy 718 may obviate the need for difficult machining and welding operations associated with geometrically intricate parts, thus potentially expanding design possibilities and facilitating cost-effective manufacture of complex components. However, processing AM builds completely free from defects, which may impair mechanical properties such as fatigue and ductility, is challenging. Anisotropic properties, microstructural heterogeneities and local formation of undesired phases are additional concerns that have motivated post-treatment of AM builds. This work investigates the microstructural changes associated with post-treatment of Alloy 718 specimens produced by Electron Beam Melting (EBM) for as-built microstructures at 3 build heights: near base plate, in the middle of build and near the top of the build. Two different post-treatment conditions, hot isostatic pressing (HIP) alone and a combined HIP with solutionising and two-step aging were examined and compared to the results for the as-built condition. The influence of various post-treatments on minor phase distributions (δ, γ″, carbides), overall porosity, longitudinal grain widths and Vickers microhardness was considered. The HIP treatment led to significant reduction in overall porosity and dissolution of δ phase, which led to appreciable grain growth for both post-treatment conditions. The variation in hardness noted as a function of build height for the as-built specimens was eliminated after post-treatment. Overall, the hardness was found to decrease after HIP and increase after the full HIP, solutionising and aging treatment, which was attributed to dissolution of γ″ during HIP and its re-precipitation in subsequent heat treatment steps.
|
|
| 17. |
- Guldris Leon, Lorena, 1983, et al.
(författare)
-
Understanding Mineral Liberation during Crushing Using Grade-by-Size Analysis - A Case Study of the Penuota Sn-Ta Mineralization, Spain
- 2020
-
Ingår i: Minerals. - : MDPI AG. - 2075-163X. ; 10:2
-
Tidskriftsartikel (refereegranskat)abstract
- Coarse comminution test-work and modeling are powerful tools in the design and optimization of mineral processing plants and provide information on energy consumption. Additional information on mineral liberation characteristics can be used for assessing the potential of pre-concentration stages or screens in the plant design. In ores of high-value metals (e.g., Ta, W), standard techniques-such as the mineralogical quantification of grain mounts by quantitative evaluation of minerals by scanning electron microscopy (QEMSCAN) or chemical analysis by X-ray fluorescence (XRF) can be challenging, due to the low relative abundance of such valuable minerals. The cost of QEMSCAN is also a limiting factor, especially considering the large number of samples required for the optimization of coarse comminution. In this study, we present an extended analytical protocol to a well-established mechanical test of interparticle breakage to improve the assessment of coarse mineral liberation characteristics. The liberation of ore minerals is a function of the rock texture and the difference in size and mechanical properties of the valuable minerals relative to gangue minerals and they may fraction in certain grain sizes if they behave differently during comminution. By analyzing the bulk-chemistry of the different grain size fractions produced after compressional testing, and by generating element by size diagrams, it is possible to understand the liberation characteristics of an ore. We show, based on a case study performed on a tantalum ore deposit, that element distribution can be used to study the influence of mechanical parameters on mineral liberation. This information can direct further mineralogical investigation and test work.
|
|
| 18. |
- Belov, Ilja, et al.
(författare)
-
Fin‐Tube and Plate Heat Exchangers : Evaluation of Transient Performance
- 2017
-
Ingår i: 18th International Conference on Thermal, Mechanical and Multi-Physics Simulation and Experiments in Microelectronics and Microsystems (EuroSimE). - : IEEE. - 9781509043446 - 9781509043439 - 9781509043453
-
Konferensbidrag (refereegranskat)abstract
- A methodology for evaluation of transient performance of, and comparison between plate heat exchanger and plate-fin-and-tube heat exchanger was developed and realized, including experiment and 3-D simulation. Heat transfer from water to a gas medium was addressed. The heated gas volume was the same for both heat exchanger designs. This was achieved by placing the plate-fin-and-tube heat exchanger into enclosure. The volume average temperature of the gas as function of time was computed. Estimated material cost for the studied designs was at least seven times lower than for the stainless steel plate heat exchanger. The performance of the selected plate-fin-and-tube heat exchanger design was found comparable to the plate heat exchanger, when both fin and tube materials were set to Al, and the enclosure was a light-weight thermal insulator. Transient behavior of the studied heat exchangers should be of interest for micro-grid applications, but also for thermal management in electronic cabinets and data centers.
|
|
| 19. |
- Wärmefjord, Kristina, 1976, et al.
(författare)
-
Welding of non-nominal geometries : physical tests
- 2016
-
Ingår i: Procedia CIRP. - : Elsevier BV. - 2212-8271. ; 43, s. 136-141
-
Tidskriftsartikel (refereegranskat)abstract
- The geometrical quality of a welded assembly is to some extent depending part positions before welding. Here, a design of experiment is set up in order to investigate this relation using physical tests in a controlled environment. Based on the experimental results it can be concluded that the influence of part position before welding is significant for geometrical deviation after welding. Furthermore, a working procedure for a completely virtual geometry assurance process for welded assemblies is outlined. In this process, part variations, assembly fixture variations and welding induced variations are important inputs when predicting the capability of the final assembly.
|
|
| 20. |
|
|
| 21. |
- Zhang, Hanzhu, 1991-, et al.
(författare)
-
A high-entropy B4(HfMo2TaTi)C and SiC ceramic composite
- 2019
-
Ingår i: Dalton Transactions. - : Royal Society of Medicine Press. - 1477-9226 .- 1477-9234. ; 48:16, s. 5161-5167
-
Tidskriftsartikel (refereegranskat)abstract
- A multicomponent composite of refractory carbides, B4C, HfC, Mo2C, TaC, TiC and SiC, of rhombohedral, face-centered cubic (FCC) and hexagonal crystal structures is reported to form a single phase B4(HfMo2TaTi)C ceramic with SiC. The independent diffusion of the metal and nonmetal atoms led to a unique hexagonal lattice structure of the B4(HfMo2TaTi)C ceramic with alternating layers of metal atoms and C/B atoms. In addition, the classical differences in the crystal structures and lattice parameters among the utilized carbides were overcome. Electron microscopy, X-ray diffraction and calculations using density functional theory (DFT) confirmed the formation of a single phase B4(HfMo2TaTi)C ceramic with a hexagonal close-packed (HCP) crystal structure. The DFT based crystal structure prediction suggests that the metal atoms of Hf, Mo, Ta and Ti are distributed on the (0001) plane in the HCP lattice, while the carbon/boron atoms form hexagonal 2D grids on the (0002) plane in the HCP unit cell. The nanoindentation of the high-entropy phase showed hardness values of 35 GPa compared to the theoretical hardness value estimated based on the rule of mixtures (23 GPa). The higher hardness was contributed by the solid solution strengthening effect in the multicomponent hexagonal structure. The addition of SiC as the secondary phase in the sintered material tailored the microstructure of the composite and offered oxidation resistance to the high-entropy ceramic composite at high temperatures.
|
|
| 22. |
- Cho, Sung-Woo, et al.
(författare)
-
Injection-molded nanocomposites and materials based on wheat gluten
- 2011
-
Ingår i: International Journal of Biological Macromolecules. - : Elsevier BV. - 0141-8130 .- 1879-0003. ; 48:1, s. 146-152
-
Tidskriftsartikel (refereegranskat)abstract
- This is, to our knowledge, the first study of the injection molding of materials where wheat gluten (WG) is the main component. In addition to a plasticizer (glycerol), 5 wt.% natural montmorillonite clay was added. X-ray indicated intercalated clay and transmission electron microscopy indicated locally good clay platelet dispersion. Prior to feeding into the injection molder, the material was first compression molded into plates and pelletized. The filling of the circular mold via the central gate was characterized by a divergent flow yielding, in general, a stronger and stiffer material in the circumferential direction. It was observed that 20–30 wt.% glycerol yielded the best combination of processability and mechanical properties. The clay yielded improved processability, plate homogeneity and tensile stiffness. IR spectroscopy and protein solubility indicated that the injection molding process yielded a highly aggregated structure. The overall conclusion was that injection molding is a very promising method for producing WG objects.
|
|
| 23. |
- Mellin, Pelle, 1985-, et al.
(författare)
-
Nano-sized by-products from metal 3D printing, composite manufacturing and fabric production
- 2016
-
Ingår i: Journal of Cleaner Production. - Sweden : Elsevier. - 0959-6526 .- 1879-1786. ; 139, s. 1224-1233
-
Tidskriftsartikel (refereegranskat)abstract
- Recently, the health and environmental perspective of nano-materials has gained attention. Most previous work focused on Engineered Nanoparticles (ENP). This paper examines some recently introduced production routes in terms of generated nano-sized by-products. A discussion on the hazards of emitting such particles and fibers is included. Fine by-products were found in recycled metal powder after 3D printing by Selective Laser Melting (SLM). The process somehow generated small round metal particles (~1e2 mm) that are possibly carcinogenic and respirable, but not small enough to enter by skin-absorption. With preventive measures like closed handling and masks, any health related effects can be prevented. The composite manufacturing in particular generated ceramic and carbonaceous particles that are very small and respirable but do not appear to be intrinsically toxic. The smallest features in agglomerates were about 30 nm. Small particles and fibers that were not attached in agglomerates were found in a wide range of sizes, from 1 μm and upwards. Preventive measures like closed handling and masks are strongly recommended. In contrast, the more traditional production route of fabric production is investigated. Here, brushing residue and recycled wool from fabric production contained few nano-sized by-products.
|
|
| 24. |
- Charles Murgau, Corinne, et al.
(författare)
-
Temperature and Microstructure Evolution in Gas Tungsten Arc Welding Wire Feed Additive Manufacturing of Ti-6Al-4V
- 2019
-
Ingår i: Materials. - : MDPI. - 1996-1944. ; 12:21
-
Tidskriftsartikel (refereegranskat)abstract
- In the present study, the gas tungsten arc welding wire feed additive manufacturing process is simulated and its final microstructure predicted by microstructural modelling, which is validated by microstructural characterization. The Finite Element Method is used to solve the temperature field and microstructural evolution during a gas tungsten arc welding wire feed additive manufacturing process. The microstructure of titanium alloy Ti-6Al-4V is computed based on the temperature evolution in a density-based approach and coupled to a model that predicts the thickness of the α lath morphology. The work presented herein includes the first coupling of the process simulation and microstructural modelling, which have been studied separately in previous work by the authors. In addition, the results from simulations are presented and validated with qualitative and quantitative microstructural analyses. The coupling of the process simulation and microstructural modeling indicate promising results, since the microstructural analysis shows good agreement with the predicted alpha lath size.
|
|
| 25. |
- Dimitrios, Nikas, et al.
(författare)
-
Evaluation of local strength via microstructural quantification in a pearlitic rail steel deformed by simultaneous compression and torsion
- 2018
-
Ingår i: Materials Science & Engineering. - : Elsevier. - 0921-5093 .- 1873-4936. ; 737, s. 341-347
-
Tidskriftsartikel (refereegranskat)abstract
- Pearlitic steels are commonly used for railway rails because they combine good strength and wear properties. During service, the passage of trains results in large accumulation of shear strains in the surface layer of the rail, sometimes leading to crack initiation. Knowledge of the material properties versus the shear strain in this layer is therefore important for fatigue life predictions. In this study, fully pearlitic R260 rail steel was deformed using a bi-axial torsion-compression machine to reach different shear strains. Microstructural parameters including interlamellar spacing, thickness of ferrite and cementite lamellae and dislocation density in the ferrite lamellae, as well as hardness were quantitatively characterized at different shear strain levels. Based on the microstructural observations and the quantification of the microstructural parameters, the local flow stresses were estimated based on boundary strengthening and dislocation strengthening models. A good agreement was found between the estimated flow stresses and the flow stresses determined from microhardness measurements. d
|
|
