SwePub - sökning: L773:0168 9002 OR L773:0167 50...

Numrering	Referens	Omslagsbild	Hitta
1.	Almehed, Sverker, et al. (författare) A Silicon-Tungsten Electromagnetic Calorimeter for LEP 1991 Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 305:2, s. 320-330 Tidskriftsartikel (refereegranskat)abstract This report describes a silicon-tungsten electromagnetic calorimeter used to determine some beam properties and luminosity in the DELPHI experiment at LEP. The polar angular range covered by this detector is 5–8 mrad, which allows the detection of a Bhabha rate about 10 times the rate of produced Z particles at the peak cross section.
2.	Andersson, Åke, et al. (författare) Beam profile measurements at MAX 1995 Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 364:1, s. 4-12 Tidskriftsartikel (refereegranskat)abstract An electron beam profile monitor system is described. It utilizes the visible bending magnet synchrotron radiation (SR) to form an image of the beam. A model for calculating diffraction and depth of field effects is introduced. Assuming a Gaussian distributed electron beam, the relation between beam image size and actual beam size is then calculated with this model, for a number of practical measuring situations. In a series of measurements at the MAX I electron storage ring at a current of 1 mA, the beam image size has been measured for these calculated situations. The measured values are presented, and their behaviour is in good agreement with the model. With this model the horizontal and vertical rms beam sizes were determined to σx = (203 ± 3) μm and σy = (19 ± 3) μm respectively. The corresponding vertical emittance is approximately 0.05 nm rad.
3.	Andersson, Åke, et al. (författare) Experiences with the narrow gap undulator at MAX-lab 1995 Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 362:2-3, s. 586-591 Tidskriftsartikel (refereegranskat)abstract An undulator with short poles (period 24 mm) and extremely narrow gap (magnet gap 7.7 mm) using a squeezable vacuum chamber has been installed and is in operation at the MAX-lab 550 MeV storage ring. The device operates with a vacuum chamber aperture down to 6.2 mm. The behaviour of the storage ring concerning lifetime, emittance, tune shift and closed orbit is well described by conventional models. We present here the design of the device, the influence on the storage ring and the spectral characteristics, as well as comparison with expected theoretical results and an overview of the activities at the beam line.
4.	Andersson, Åke, et al. (författare) Positron production for ESRF 1988 Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 267:1, s. 15-21 Tidskriftsartikel (refereegranskat)abstract In this report, we first discuss some different pre-injector possibilities for the ESRF booster synchrotron, using estimated machine performances. We then focus on the commercially available linac schemes carrying out more detailed calculations. We also look into the possibility of recyling the particles through the linacs.
5.	Andersson, Åke, et al. (författare) The MAX II synchrotron radiation storage ring 1994 Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 343:2-3, s. 644-649 Tidskriftsartikel (refereegranskat)abstract A 1.5 GeV third generation storage ring optimised for the VUV and soft X-ray spectral region is currently being built at MAX-lab. The magnet lattice, ring architecture and production choices are optimised to fit within rather tight boundary conditions without sacrificing performance. In this paper, the magnet lattice, light characteristics, injection and technical solutions for the ring are presented.
6.	Da Via, C, et al. (författare) Lightwave Analogue Links For LHC Detector Front-ends 1994 Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 344:1, s. 199-211 Tidskriftsartikel (refereegranskat)abstract The requirements on optical links for transferring analog and digital signals from the detector front-ends to the readout electronics at future high-luminosity colliders are reviewed. The advantages of external modulation techniques are discussed. An outline is given of the the R&D programme recently started at CERN by a collaboration involving high-energy physics institutes, optoelectronics research laboratories and industry, in order to develop electro-optic intensity modulator arrays, particularly for analogue applications, and to investigate the feasibility of volume production. The design of multichannel demonstrators in lithium niobate and III-V semiconductor technology is described. Preliminary results of the performance measurements are presented.
7.	Hedin, Lars (författare) Properties of electron self-energies and their role in electron spectroscopies 1991 Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; A308:1-2, s. 169-177 Tidskriftsartikel (refereegranskat)abstract The GW approximation for the self-energy connected with the one-electron Green's function has been very successful in predicting band structures for a large class of semiconductors and insulators. The physical basis for this approximation and general features of its nonlocality are discussed, as well as possible improvements. Besides quasiparticle energies the self-energy also gives the intrinsic part of the photoelectron spectrum. In general, however, a full description of experimental spectra measured with synchrotron radiation, such as photoemission, Auger spectra and EXAFS, cannot be given by the one-electron Green's function. A new theoretical approach to synchrotron radiation spectroscopies is given in terms of the coupling functions involved in the GW approximation and on-the-energy-shell one-electron Green's functions.(14 refs)
8.	Scheffel, Jan, 1954- (författare) Neutron Spectra from Beam-Heated Fusion Plasmas 1984 Ingår i: Nuclear Instruments and Methods in Physics Research Section A. - : Elsevier BV. - 0168-9002 .- 1872-9576 .- 0167-5087. ; 224:3, s. 519-531 Tidskriftsartikel (refereegranskat)abstract The spectra of fusion neutrons emerging from a deuterium-beam heated deuterium or tritium plasma yield information of both the bulk plasma and of the beam slowing down. A computer code has been developed to model plasma-plasma (p-p), beam-plasma (b-p) and beam-beam (b-b) interaction for the case of a single or several co-directed beams. It is found that for a high-temperature plasma (T ⪢ 1 keV) b-b interaction is negligible due to the low associated neutron emission. p-p neutron spectra reflect the bulk ion plasma temperature and density as well as toroidal rotational velocity. b-p spectra shifts and broadenings are sensitive to beam injection geometry and deposition, beam energy, ion and electron temperature, toroidal rotation and the density of neutrals. The mixing of full energy beam neutrals with half- and third-energy components has only a slight impact on the neutron spectrum when the beam power is held constant. For a JET-like Tokamak (D → D, beam power 5 MW, beam energy 160 keV) it is further found that for T ⪡ 8 keV the b-p neutron flux dominates, whereas for T ⪢ 8 keV the p-p flux dominates.
9.	Abat, E., et al. (författare) Study of the response of the ATLAS central calorimeter to pions of energies from 3 to 9 GeV 2009 Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002 .- 1872-9576. ; 607:2, s. 372-386 Tidskriftsartikel (refereegranskat)abstract A fully instrumented slice of the ATLAS central detector was exposed to test beams from the SPS (Super Proton Synchrotron) at CERN in 2004. in this paper, the response of the central calorimeters to pions with energies in the range between 3 and 9 GeV is presented. The linearity and the resolution of the combined calorimetry (electromagnetic and hadronic calorimeters) was measured and compared to the prediction of a detector simulation program using the toolkit Geant 4. (C) 2009 Elsevier B.V. All rights reserved.
10.	Abata, E., et al. (författare) Study of energy response and resolution of the ATLAS barrel calorimeter to hadrons of energies from 20 to 350 GeV 2010 Ingår i: Nuclear Instruments and Methods in Physics Research Section A. - : Elsevier. - 0168-9002 .- 1872-9576 .- 0167-5087. ; 621:1-3, s. 134-150 Tidskriftsartikel (refereegranskat)abstract A fully instrumented slice of the ATLAS detector was exposed to test beams from the SPS (Super Proton Synchrotron) at CERN in 2004. In this paper, the results of the measurements of the response of the barrel calorimeter to hadrons with energies in the range 20-350 GeV and beam impact points and angles corresponding to pseudo-rapidity values in the range 0.2-0.65 are reported. The results are compared to the predictions of a simulation program using the Geant 4 toolkit. (C) 2010 Published by Elsevier B.V.
11.	Acharya, S, et al. (författare) The ALICE transition radiation detector: Construction, operation, and performance 2018 Ingår i: Nuclear Instruments and Methods in Physics Research, Section A: Accelerators, Spectrometers, Detectors and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 881, s. 88-127 Tidskriftsartikel (refereegranskat)abstract The Transition Radiation Detector (TRD) was designed and built to enhance the capabilities of the ALICE detector at the Large Hadron Collider (LHC). While aimed at providing electron identification and triggering, the TRD also contributes significantly to the track reconstruction and calibration in the central barrel of ALICE. In this paper the design, construction, operation, and performance of this detector are discussed. A pion rejection factor of up to 410 is achieved at a momentum of 1 GeV/c in p-Pb collisions and the resolution at high transverse momentum improves by about 40% when including the TRD information in track reconstruction. The triggering capability is demonstrated both for jet, light nuclei, and electron selection. © 2017 CERN for the benefit of the ALICE Collaboration.
12.	Adler, Jan-Olof, et al. (författare) The upgraded photon tagging facility at the MAX IV Laboratory 2013 Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 715, s. 1-10 Tidskriftsartikel (refereegranskat)abstract A description is given of the upgraded photon tagging facility at the MAX IV Laboratory. Two magnetic spectrometers are used to momentum analyze post-bremsstrahlung electrons. The tagged photon range extends from 10 to 180 MeV with an energy resolution of about 300 keV. The system has been operated at rates up to 4 x 10(6) photons s(-1) MeV (-1). Different diagnostic tools are described as well as the experimental program.
13.	Aggarwal, M.M, et al. (författare) Particle identification studies with a full-size 4-GEM prototype for the ALICE TPC upgrade 2018 Ingår i: Nuclear Instruments and Methods in Physics Research, Section A: Accelerators, Spectrometers, Detectors and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 903, s. 215-223 Tidskriftsartikel (refereegranskat)abstract A large Time Projection Chamber is the main device for tracking and charged-particle identification in the ALICE experiment at the CERN LHC. After the second long shutdown in 2019/20, the LHC will deliver Pb beams colliding at an interaction rate of about 50 kHz, which is about a factor of 50 above the present readout rate of the TPC. This will result in a significant improvement on the sensitivity to rare probes that are considered key observables to characterize the QCD matter created in such collisions. In order to make full use of this luminosity, the currently used gated Multi-Wire Proportional Chambers will be replaced. The upgrade relies on continuously operated readout detectors employing Gas Electron Multiplier technology to retain the performance in terms of particle identification via the measurement of the specific energy loss by ionization dE/dx. A full-size readout chamber prototype was assembled in 2014 featuring a stack of four GEM foils as an amplification stage. The performance of the prototype was evaluated in a test beam campaign at the CERN PS. The dE/dx resolution complies with both the performance of the currently operated MWPC-based readout chambers and the challenging requirements of the ALICE TPC upgrade program. Detailed simulations of the readout system are able to reproduce the data. © 2018 Elsevier B.V.
14.	Ainsworth, Robert, et al. (författare) The influence of parasitic modes on beam dynamics for the European spallation source linac 2014 Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 734, s. 95-100 Tidskriftsartikel (refereegranskat)abstract The European Spallation Source (ESS) linac will consist of three families of superconducting RE cavities to accelerate protons to a final beam energy of 2.5 GeV for collision with the target. Beam induced HOMs in these cavities may drive the beam unstable and increase the cryogenic load, severely limiting the operation of the linac. The effect of these modes on the beam quality is investigated in detail using a numerical code dedicated to beam-HOM interaction. (C) 2012 Elsevier B.V. All rights reserved.
15.	Akkoyun, S., et al. (författare) AGATA - Advanced GAmma Tracking Array 2012 Ingår i: Nuclear Instruments and Methods in Physics Research, Section A: Accelerators, Spectrometers, Detectors and Associated Equipment. - : Elsevier BV. - 0168-9002 .- 0167-5087 .- 1872-9576. ; 668, s. 26-58 Tidskriftsartikel (refereegranskat)abstract The Advanced GAmma Tracking Array (AGATA) is a European project to develop and operate the next generation γ-ray spectrometer. AGATA is based on the technique of γ-ray energy tracking in electrically segmented high-purity germanium crystals. This technique requires the accurate determination of the energy, time and position of every interaction as a γ ray deposits its energy within the detector volume. Reconstruction of the full interaction path results in a detector with very high efficiency and excellent spectral response. The realisation of γ-ray tracking and AGATA is a result of many technical advances. These include the development of encapsulated highly segmented germanium detectors assembled in a triple cluster detector cryostat, an electronics system with fast digital sampling and a data acquisition system to process the data at a high rate. The full characterisation of the crystals was measured and compared with detector- response simulations. This enabled pulse-shape analysis algorithms, to extract energy, time and position, to be employed. In addition, tracking algorithms for event reconstruction were developed. The first phase of AGATA is now complete and operational in its first physics campaign. In the future AGATA will be moved between laboratories in Europe and operated in a series of campaigns to take advantage of the different beams and facilities available to maximise its science output. The paper reviews all the achievements made in the AGATA project including all the necessary infrastructure to operate and support the spectrometer. © 2011 Elsevier B.V. All rights reserved.
16.	Alcorn, J, et al. (författare) Basic instrumentation for Hall A at Jefferson Lab 2004 Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 522:3, s. 294-346 Tidskriftsartikel (refereegranskat)abstract The instrumentation in Hall A at the Thomas Jefferson National Accelerator Facility was designed to study electro-and photo-induced reactions at very high luminosity and good momentum and angular resolution for at least one of the reaction products. The central components of Hall A are two identical high resolution spectrometers, which allow the vertical drift chambers in the focal plane to provide a momentum resolution of better than 2 x 10(-4). A variety of Cherenkov counters, scintillators and lead-glass calorimeters provide excellent particle identification. The facility has been operated successfully at a luminosity well in excess of 10(38) CM-2 s(-1). The research program is aimed at a variety of subjects, including nucleon structure functions, nucleon form factors and properties of the nuclear medium. (C) 2003 Elsevier B.V. All rights reserved.
17.	Alkhazov, GD, et al. (författare) SPES4-pi: installation for exclusive study of nuclear reactions 2005 Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 551:2-3, s. 290-311 Tidskriftsartikel (refereegranskat)abstract The paper describes the spectrometric system "SPES4-pi" used at the National Laboratory Saturne (CE Saclay, France) for the exclusive study of the baryon resonance excitation in inelastic alpha and d scattering on the proton, as well as coherent pion production in charge exchange reactions. The system consists of the magnetic spectrometer SPES4 and two wide-aperture position-sensitive detector arrays, equipped with wire chambers and scintillator hodoscopes, installed around a large-gap C-shape dipole magnet.
18.	Alme, J., et al. (författare) The ALICE TPC, a large 3-dimensional tracking device with fast readout for ultra-high multiplicity events 2010 Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 622:1, s. 316-367 Tidskriftsartikel (refereegranskat)abstract The design, construction, and commissioning of the ALICE Time-Projection Chamber (TPC) is described. It is the main device for pattern recognition, tracking, and identification of charged particles in the ALICE experiment at the CERN LHC. The TPC is cylindrical in shape with a volume close to 90 m(3) and is operated in a 0.5T solenoidal magnetic field parallel to its axis. In this paper we describe in detail the design considerations for this detector for operation in the extreme multiplicity environment of central Pb-Pb collisions at LHC energy. The implementation of the resulting requirements into hardware (field cage, read-out chambers, electronics), infrastructure (gas and cooling system, laser-calibration system), and software led to many technical innovations which are described along with a presentation of all the major components of the detector, as currently realized. We also report on the performance achieved after completion of the first round of stand-alone calibration runs and demonstrate results close to those specified in the TPC Technical Design Report. (C) 2010 CERN for the benefit of the ALICE collaboration. Published by Elsevier B.V. All rights reserved.
19.	Alvarez-Pol, H., et al. (författare) Performance analysis for the CALIFA Barrel calorimeter of the (RB)-B-3 experiment 2014 Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 767, s. 453-466 Tidskriftsartikel (refereegranskat)abstract The CALIFA calorimeter is an advanced detector for gamma rays and light charged particles, accordingly optimized for the demanding requirements of the physics programme proposed for the (RB)-B-3 facility at FAIR. The multipurpose character of CALIFA is required to fulfil challenging demands in energy resolution (5-6% at 1 MeV for gamma rays) and efficiency. Charged particles, e.g. protons of energies up to 320 MeV in the Barrel section, should also be identified with an energy resolution better to 1%. CALIFA is divided into two well-separated sections: a "Forward EndCap" and a cylindrical "Barrel" covering an angular range from 43.2 degrees to 140.3 degrees. The Barrel section, based on long CsI(Tl) pyramidal frustum crystals coupled to large area avalanche photodiodes (LAAPDs), attains the requested high efficiency for calorimetric purposes. The construction of the CALIFA Demonstrator, comprising 20% of the total detector, has already been initiated, and commissioning experiments are expected for 2014. The assessment of the capabilities and expected performance of the detector elements is a crucial step in their design, along with the prototypes evaluation. For this purpose, the Barrel geometry has been carefully implemented in the simulation package R3BRoot, including easily variable thicknesses of crystal wrapping and carbon fibre supports. A complete characterization of the calorimeter response (including efficiency, resolution, evaluation of energy and reconstruction losses) under different working conditions, with several physics cases selected to probe the detector performance over a wide range of applications, has been undertaken. Prototypes of different sections of the CALIFA Barrel have been modeled and their responses have been evaluated and compared with the experimental results. The present paper summarizes the outcome of the simulation campaign for the entire Barrel section and for the corresponding prototypes tested at different European installations. (C) 2014 Elsevier B.V. All rights reserved
20.	Andersen, C. E., et al. (författare) Medical proton dosimetry using radioluminescence from aluminium oxide crystals attached to optical-fiber cables 2007 Ingår i: Nuclear Instruments and Methods in Physics Research Section A. - : Elsevier BV. - 0168-9002 .- 1872-9576 .- 0167-5087. ; 580:1, s. 466-468 Tidskriftsartikel (refereegranskat)abstract The prime objective of this study is to investigate if radioluminescence (RL) from carbon-doped aluminum oxide (Al2O3:C) crystals potentially can be used for absorbed dose-rate measurements during proton radiotherapy. The RL from two separate (2 mg) Al2O3:C crystals attached to optical-fiber cables were recorded during irradiations in water in a 175 MeV clinical proton beam. The RL response for low-LET protons in the plateau region of the Bragg curve was found to closely resemble that observed for a clinical 6 MV X-ray beam. An identical response was found in the Bragg peak (where the dose-averaged LET is about 4 keV/mu m) for absorbed doses less than 0.3 Gy. For doses in the range of 0.3-3Gy, we observed a significant decrease in luminescence efficiency with LET. At 3 Gy, the luminescence efficiency was about 60% in the Bragg-peak region. The study implies that the RL-signal from Al2O3:C could potentially be suitable for medical proton dosimetry in the 0-0.3 Gy range even without any LET-dependent correction factors.
21.	Andersen, Ken, et al. (författare) B-10 multi-grid proportional gas counters for large area thermal neutron detectors 2013 Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002 .- 1872-9576. ; 720, s. 116-121 Tidskriftsartikel (refereegranskat)abstract He-3 was a popular material in neutrons detectors until its availability dropped drastically in 2008. The development of techniques based on alternative convertors is now of high priority for neutron research institutes. Thin films of B-10 or (B4C)-B-10 have been used in gas proportional counters to detect neutrons, but until now, only for small or medium sensitive area. We present here the multi-grid design, introduced at the ILL and developed in collaboration with ESS for LAN (large area neutron) detectors. Typically thirty (B4C)-B-10 films of 1 mu m thickness are used to convert neutrons into ionizing particles which are subsequently detected in a proportional gas counter. The principle and the fabrication of the multi-grid are described and some preliminary results obtained with a prototype of 200 cm x 8 cm are reported; a detection efficiency of 48% has been measured at 2.5 angstrom with a monochromatic neutron beam line, showing the good potential of this new technique. (C) 2013 Elsevier B.V. All rights reserved.
22.	Andersen, K. H., et al. (författare) The instrument suite of the European Spallation Source 2020 Ingår i: Nuclear Instruments and Methods in Physics Research, Section A: Accelerators, Spectrometers, Detectors and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 957 Tidskriftsartikel (refereegranskat)abstract An overview is provided of the 15 neutron beam instruments making up the initial instrument suite of the European Spallation Source (ESS), and being made available to the neutron user community. The ESS neutron source consists of a high-power accelerator and target station, providing a unique long-pulse time structure of slow neutrons. The design considerations behind the time structure, moderator geometry and instrument layout are presented. The 15-instrument suite consists of two small-angle instruments, two reflectometers, an imaging beamline, two single-crystal diffractometers; one for macromolecular crystallography and one for magnetism, two powder diffractometers, and an engineering diffractometer, as well as an array of five inelastic instruments comprising two chopper spectrometers, an inverse-geometry single-crystal excitations spectrometer, an instrument for vibrational spectroscopy and a high-resolution backscattering spectrometer. The conceptual design, performance and scientific drivers of each of these instruments are described. All of the instruments are designed to provide breakthrough new scientific capability, not currently available at existing facilities, building on the inherent strengths of the ESS long-pulse neutron source of high flux, flexible resolution and large bandwidth. Each of them is predicted to provide world-leading performance at an accelerator power of 2 MW. This technical capability translates into a very broad range of scientific capabilities. The composition of the instrument suite has been chosen to maximise the breadth and depth of the scientific impact of the early years of the ESS, and provide a solid base for completion and further expansion of the facility.
23.	Andersson, Joel, et al. (författare) New features of the MAX IV thermionic pre-injector 2017 Ingår i: Nuclear Instruments and Methods in Physics Research, Section A: Accelerators, Spectrometers, Detectors and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 855, s. 65-80 Tidskriftsartikel (refereegranskat)abstract The MAX IV facility in Lund, Sweden consists of two storage rings for production of synchrotron radiation. The smaller 1.5 GeV ring is presently under construction, while the larger 3 GeV ring is being commissioned. Both rings will be operating with top-up injections from a full-energy injector. During injection, the electron beam is first delivered to the main injector from a thermionic pre-injector which consists of a thermionic RF gun, a chopper system, and an energy filter. In order to reduce losses of high-energy electrons along the injector and in the rings, the electron beam provided by the thermionic pre-injector should have the correct time structure and energy distribution. In this paper, the design of the MAX IV thermionic pre-injector with all its sub components is presented. The electron beam delivered by the pre-injector and its dependence on parameters such as optics, cathode temperature, and RF power are studied. Measurements are here compared with simulation results obtained by particle tracking and electromagnetic codes. The chopper system is described in detail, and different driving schemes that optimize the injection efficiency for the two storage rings are investigated. During operation, it was discovered that the structure of the beam delivered by the gun is affected by mode beating between the accelerating and a low-order mode. This mode beating is also studied in detail. Finally, initial measurements of the electron beam delivered to the 3 GeV ring during commissioning are presented.
24.	Andersson, L-L, et al. (författare) TASISpec - A Highly Efficient Multi-coincidence Spectrometer for Nuclear Structure Investigations of the Heaviest Nuclei 2010 Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 622:1, s. 164-170 Tidskriftsartikel (refereegranskat)abstract TASISpec (TASCA in Small Image mode Spectroscopy) combines composite Ge- and Si-detectors for a new detector setup aimed towards multi-coincidence gamma -ray, X-ray, conversion electron, fission fragment, and a-particle spectroscopy of the heaviest nuclei. It exploits the TASCA separator's unique small image focal mode, i.e. the fact that evaporation residues produced in fusion-evaporation reactions can be focused into an area of less than 3 cm in diameter. This provides the possibility to pack detectors in very close geometry, resulting in an unprecedented detection efficiency of radioactive decays in prompt and delayed coincidence with implanted nuclei. Crown Copyright (C) 2010 Published by Elsevier B.V. All rights reserved.
25.	Antonov, A. N., et al. (författare) The electron-ion scattering experiment ELISe at the International Facility for Antiproton and Ion Research (FAIR)-A conceptual design study 2011 Ingår i: Nuclear Instruments and Methods in Physics Research, Section A: Accelerators, Spectrometers, Detectors and Associated Equipment. - : Elsevier BV. - 0168-9002 .- 0167-5087. ; 637:1, s. 60-76 Tidskriftsartikel (refereegranskat)abstract The electron-ion scattering experiment ELISe is part of the installations envisaged at the new experimental storage ring at the International Facility for Antiproton and Ion Research (FAIR) in Darmstadt, Germany. It offers an unique opportunity to use electrons as probe in investigations of the structure of exotic nuclei. The conceptual design and the scientific challenges of ELISe are presented. (C) 2011 Elsevier B.V. All rights reserved.
26.	Artemiev, AN, et al. (författare) Planar parabolic X-ray refractive lens made of glassy carbon 2005 Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 543:1, s. 322-325 Tidskriftsartikel (refereegranskat)abstract Experimental results of synchrotron radiation focusing by parabolic planar compound refractive lenses, made of glassy carbon, are presented. The lenses with the curvature radius of 5 and 200 mu m, and with the geometric aperture of 40 and 900 mu m were developed. The number of bi-concave elements in the compound lenses was from 4 to 200. The experiments were performed at the ESRF at the bending magnet beamline BM-5. The minimum size of the focus was observed as 1.41 mu m.
27.	Ask, S., et al. (författare) Luminosity measurement at ATLAS - Development, construction and test of scintillating fibre prototype detectors 2006 Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 568:2, s. 588-600 Tidskriftsartikel (refereegranskat)abstract We are reporting about a scintillating fibre tracking detector which is proposed for the precise determination of the absolute luminosity of the CERN LHC at interaction point 1 where the ATLAS experiment is located. The detector needs to track protons elastically scattered under mu rad angles in direct vicinity to the LHC beam. It is based on square shaped scintillating plastic fibres read out by multianode photomultiplier tubes and is housed in Roman Pots. We describe the design and construction of prototype detectors and the results of a beam test experiment at DESY. The excellent detector performance established in this test validates the detector design and supports the feasibility of the proposed challenging method of luminosity measurement. (c) 2006 Elsevier B.V. All rights reserved.
28.	Aurand, Bastian, et al. (författare) Enhanced radiation pressure-assisted acceleration by temporally tuned counter-propagating pulses 2014 Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 740, s. 83-86 Tidskriftsartikel (refereegranskat)abstract Within the last decade, laser-ion acceleration has become a field of broad interest. The possibility to generate short proton- or heavy ion bunches with an energy of a few tens of MeV by table-top laser systems could open new opportunities for medical or technical applications. Nevertheless, today's laser-acceleration schemes lead mainly to a temperature-like energy distribution of the accelerated ions, a big disadvantage compared to mono-energetic beams from conventional accelerators. Recent results 111 of laser-ion acceleration using radiation-pressure appear promising to overcome this drawback. In this paper, we demonstrate the influence of a second counter-propagating laser pulse interacting with a nm-thick target, creating a well defined pre-plasma. (C) 2013 Elsevier B.V. All rights reserved.
29.	Bardies, Manuel, et al. (författare) Quantitative imaging for clinical dosimetry 2006 Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 569:2, s. 467-471 Tidskriftsartikel (refereegranskat)abstract Patient-specific dosimetry in nuclear medicine is now a legal requirement in many countries throughout the EU for targeted radionuclide therapy (TRT) applications. In order to achieve that goal, an increased level of accuracy in dosimetry procedures is needed. Current research in nuclear medicine dosimetry should not only aim at developing new methods to assess the delivered radiation absorbed dose at the patient level, but also to ensure that the proposed methods can be put into practice in a sufficient number of institutions. A unified dosimetry methodology is required for making clinical outcome comparisons possible.
30.	Batkov, Konstantin, et al. (författare) Unperturbed moderator brightness in pulsed neutron sources 2013 Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 729, s. 500-505 Tidskriftsartikel (refereegranskat)abstract The unperturbed neutron brightness of a moderator can be defined from the number of neutrons leaving the surface of a moderator completely surrounded by a reflector. Without openings for beam extraction, it is the maximum brightness that can be theoretically achieved in a moderator. The unperturbed brightness of a cylindrical cold moderator filled with pure para-H-2 was calculated using MCNPX; the moderator dimensions were optimised, for a fixed target and reflector geometry corresponding to the present concept for the BS spallation source. This quantity does not depend on openings for beam extraction and therefore can be used for a first-round optimisation of a moderator, before effects due to beam openings are considered. We find that such an optimisation yields to a factor of 2 increase with respect to a conventional volume moderator, large enough to accommodate a viewed surface of 12 x 12 cm(2): the unperturbed neutron brightness is maximum for a disc-shaped moderator of 15 cm diameter, 1.4 cm height. The reasons for this increase can be related to the properties of the scattering cross-section of paraH(2), to the added reflector around the exit surface in the case of a compact moderator, and to a directionality effect. This large optimisation gain in the unperturbed brightness hints towards similar potentials for the perturbed neutron brightness, in particular in conjunction with advancing the optical quality of neutron delivery from the moderator to the sample, where by Lionville theorem the brightness is conserved over the beam trajectory, except for absorption and similar type losses. (C) 2013 Elsevier B.V. All rights reserved
31.	Bentley, Phillip, et al. (författare) Correction of optical aberrations in elliptic neutron guides 2012 Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 693, s. 268-275 Tidskriftsartikel (refereegranskat)abstract Modern, nonlinear ballistic neutron guides are an attractive concept in neutron beam delivery and instrumentation because they offer increased performance over straight or linearly tapered guides. However, like other ballistic geometries they have the potential to create significantly non-trivial instrumental resolution functions. We address the source of the most prominent optical aberration, namely coma, and we show that for extended sources the off-axis rays have a different focal length from on-axis rays, leading to multiple reflections in the guide system. We illustrate how the interplay between coma, sources of finite size, and mirrors with non-perfect reflectivity can therefore conspire to produce uneven distributions in the neutron beam divergence, a source of complicated resolution functions. To solve these problems, we propose a hybrid elliptic-parabolic guide geometry. Using this new kind of neutron guide shape, it is possible to condition the neutron beam and remove almost all of the aberrations, whilst providing the same performance in beam current as a standard elliptic neutron guide. We highlight the positive implications for neutron scattering instruments that this new shape can bring. (c) 2012 Elsevier B.V. All rights reserved.
32.	Bevilacqua, Riccardo, et al. (författare) A procedure for the characterization of electron transmission through Frisch grids 2015 Ingår i: Nuclear Instruments and Methods in Physics Research Section A. - : Elsevier. - 0168-9002 .- 1872-9576 .- 0167-5087. ; 770, s. 64-67 Tidskriftsartikel (refereegranskat)abstract In Frisch grid ionization chambers special attention must be paid to the operating voltages in order to avoid unwanted collection of electrons on the Frisch grid. Collection of electrons on the grid will lead to a decreased signal to noise ratio and consequently a deteriorated energy resolution. Furthermore, systematic errors in the determination of the angular distribution will be introduced. Theoretical formulas for minimized collection of electrons on the grid were derived by Bunemann et al. [3] in the special case of a Frisch grid consisting of a plane of parallel wires. No such formulas exist for other grid geometries and a careful calibration procedure is needed. We describe here a procedure for characterizing the Frisch grid in terms of its transparency to electrons for a grid consisting of a mesh of crossed wires.
33.	Biedron, Sandra G., et al. (författare) Evolution of transverse modes in a high-gain free-electron laser 2004 Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 528:1-2, s. 443-447 Tidskriftsartikel (refereegranskat)abstract At the point of saturation in a high-gain free-electron laser (FEL) the light is fully transversely coherent. The number and evolution of the transverse modes is important for the effective tune-up and subsequent operation of FELs based on the photon beam characterization and in designing multi-module devices that rely on relatively stable saturation distances in each module. In the latter, this is particularly critical since each section will seed another module. Overall, in a single- or multi-module device, experimental users will desire stability in power and in photon beam quality. Using a numerical simulation code, the evolution of the transverse modes in the high-gain free-electron laser (FEL) is examined and is discussed. In addition, the transverse modes in the first few higher nonlinear harmonics are investigated.
34.	Björneholm, Olle, et al. (författare) Free clusters studied by core-level spectroscopies 2009 Ingår i: Nuclear Instruments and Methods in Physics Research Section A. - : Elsevier BV. - 0168-9002 .- 1872-9576 .- 0167-5087. ; 601:1-2, s. 161-181 Forskningsöversikt (refereegranskat)abstract In this review we describe the development and current status of free clusters studied using core-level spectroscopies. This topic ranges from simple model systems, such as rare gas clusters, to molecular clusters, and clusters of solids, held together by ionic, covalent and metallic bonding.
35.	Boisvert, V, et al. (författare) Characterization of oxygen dimer-enriched silicon detectors 2005 Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 552:1-2, s. 49-55 Tidskriftsartikel (refereegranskat)abstract Various types of silicon material and silicon p(+)n diodes have been treated to increase the concentration of the oxygen dimer (02) defect. This was done by exposing the bulk material and the diodes to 6 MeV electrons at a temperature of about 350 degrees C. FTIR spectroscopy has been performed on the processed material confirming the formation of oxygen dimer defects in Czochralski silicon pieces. We also show results from TSC characterization on processed diodes. Finally, we investigated the influence of the dimer enrichment process on the depletion voltage of silicon diodes and performed 24 GeV/c proton irradiations to study the evolution of the macroscopic diode characteristics as a function of fluence.
36.	Breunlin, Jonas, et al. (författare) Methods for measuring sub-pm rad vertical emittance at the Swiss Light Source 2015 Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 803, s. 55-64 Tidskriftsartikel (refereegranskat)abstract We report on methods capable of measuring a rms vertical electron beam size of 3 pm with a runs error of less than 10% at a diagnostic beamline at the Swiss Light Source (SLS). This corresponds to a vertical emittance 01 06 pm rad with a 20% rms error. We showed this capability by presenting the theoretical basis for, and the data from, a series of measurements on a stable beam at 1.6 pm rad vertical emittance at the SLS. The methods presented utilized either pi- or sigma-polarized synchrotron radiation (SR) in the visible to ultra violet (vis-UV) spectral range. In addition to the established g-polarization method, we introduced a diffraction method with a potentially high resolution capability. Also an intensity imbalanced diffraction scheme was introduced, but was found to be prone to SR induced carbon contamination on optical elements. (C) 2015 Elsevier B.V. All rights reserved.
37.	Bruzzi, M, et al. (författare) Radiation-hard semiconductor detectors for SuperLHC 2005 Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 541:1-2, s. 189-201 Tidskriftsartikel (refereegranskat)abstract An option of increasing the luminosity of the Large Hadron Collider (LHC) at CERN to 1035 cm-2 s-1 has been envisaged to extend the physics reach of the machine. An efficient tracking down to a few centimetres from the interaction point will be required to exploit the physics potential of the upgraded LHC. As a consequence, the semiconductor detectors close to the interaction region will receive severe doses of fast hadron irradiation and the inner tracker detectors will need to survive fast hadron fluences of up to above 1016cm-2. The CERN-RD50 project "Development of Radiation Hard Semiconductor Devices for Very High Luminosity Colliders" has been established in 2002 to explore detector materials and technologies that will allow to operate devices up to, or beyond, this limit. The strategies followed by RD50 to enhance the radiation tolerance include the development of new or defect engineered detector materials (SiC, GaN, Czochralski and epitaxial silicon, oxygen enriched Float Zone silicon), the improvement of present detector designs and the understanding of the microscopic defects causing the degradation of the irradiated detectors. The latest advancements within the RD50 collaboration on radiation hard semiconductor detectors will be reviewed and discussed in this work.
38.	Carlén, Lars, et al. (författare) CHICSi - a compact ultra-high vacuum compatible detector system for nuclear reaction experiments at storage rings. III. readout system 2004 Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 516:2-3, s. 327-347 Tidskriftsartikel (refereegranskat)abstract (CHICSi) Celsius Heavy Ion Collaboration Si detector system is a high granularity, modular detector telescope array for operation around the cluster-jet target/circulating beam intersection of the CELSIUS storage ring at the The. Svedberg Laboratory in Uppsala, Sweden. It is able to provide identity and momentum vector of up to 100 charged particles and fragments from proton-nucleus and nucleus-nucleus collisions at intermediate energies, 50-1000A MeV. All detector telescopes as well as the major part of electronic readout system are placed inside the target chamber in ultra-high vacuum (UHV, 10(-9)-10(-7) Pa). This requires Very Large Scale Integrated (VLSI) microchip for the spectroscopic signal processing and the generation and transport of digital control signals. Eighteen telescopes, read out with chip-on-board technique by ceramics Mother Boards (MB) and corresponding 18 microchips are mounted on a 450 x 45 mm(2) Grand Mother Board (GMB), processed on FR4 glass-fibre material. Each of these 28 GMB units contains a daisy-chain organisation of the VLSI chips and associated protection circuits. Analogue-to-digital conversion of the spectroscopic signals is performed on a board outside the chamber which is connected on one side to a power distribution board, directly attached to a UHV mounting flange, and on the other side to the VME-based data acquisition system (CHICSiDAQ). This in its turn is connected via a fibre-optic link to the general TSL acquisition system (SVEDAQ), and in this way data from auxiliary detector systems, read out in CAMAC mode, can be stored in coincidence with CHICSi data.
39.	Christiansen, Peter, et al. (författare) The influence of detector effects on TPC performance 2009 Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 609:2-3, s. 149-155 Tidskriftsartikel (refereegranskat)abstract TPC stand alone simulations based on different energy loss models are compared to previously reported measurements with an ALICE TPC prototype. The performance obtained from simulations is shown to depend significantly on all the included detector effects stressing that energy loss model calculations alone are inadequate for describing the performance. When all effects are included, a good quantitative description of both the specific energy loss and the space point resolution can be obtained from all models. This shows that the TPC description in the official ALICE TPC simulation is in agreement with the measured test beam data. (C) 2009 Elsevier B.V. All rights reserved.
40.	Cutic, Nino, et al. (författare) Characterization of the arrival time jitter at the MAX-lab test-FEL using electro-optical spectral decoding 2011 Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 626, s. 16-19 Tidskriftsartikel (refereegranskat)abstract Electro-optical spectral decoding is used as an online diagnostic tool at the MAX-lab test-FEL to characterize the arrival time of electrons relative to the seed-laser pulse, measure the jitter between them and to measure the relative width of the electron bunch in order to optimize compression. Frequency characteristics of the jitter are presented. The measurements are used to get information on possible causes of the jitter and accompanying drifts. (C) 2010 Elsevier B.V. All rights reserved.
41.	Desforges, F. G., et al. (författare) Reproducibility of electron beams from laser wakefield acceleration in capillary tubes 2014 Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 740, s. 54-59 Tidskriftsartikel (refereegranskat)abstract The stability of accelerated electron beams produced by self injection of plasma electrons into the wakefield driven by a laser pulse guided inside capillary tubes is analyzed statistically in relation to laser and plasma parameters, and compared to results obtained in a gas jet. The analysis shows that reproducible electron beams are achieved with a charge of 66 pC +/- 11%, a FWHM beam divergence of 9 mrad +/- 14%, a maximum energy of 120 MeV +/- 10% and pointing fluctuations of 2.3 mrad using 10 mm long, 178 mu m diameter capillary tubes at an electron density of (10.0 +/- 1.5) x 10(18) cm(-3). Active stabilization of the laser pointing was used and laser parameters were recorded on each shot. Although the shot-to-shot laser energy fluctuations can account for a fraction of the electrons fluctuations, gas density fluctuations are suspected to be a more important source of instability. (C) 2013 Elsevier B.V. All rights reserved.
42.	DiJulio, Douglas, et al. (författare) Proton in-beam tests of the Lund (RB)-B-3 calorimeter prototype 2009 Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 612:1, s. 127-132 Tidskriftsartikel (refereegranskat)abstract A small-scale prototype of the CALIFA calorimeter, which is a subsystem of the R 3 B detector, has been constructed and tested using the 179 MeV proton beam at The Svedberg Laboratory, Uppsala, Sweden. The prototype consists of 15 Csl(Tl) elements with a size of 10 x 30 x 130 mm(3), assembled in a 3 x 5 array. Each crystal was individually tested using gamma-ray sources and the light output uniformity along the longitudinal axes was adjusted to better than 0.6%. An energy resolution of similar to 0.5% has been achieved with a technique consisting of non-uniform polishing/lapping of the crystal side facets. The performance of the prototype is evaluated using experimental data and GEANT4 simulations. Results from the experiment, including multiplicity and sum spectra, show good agreement with simulations. The quality requirements for Csl(Tl) elements for construction of a high precision calorimeter/spectrometer are summarized. (C) 2009 Elsevier B.V. All rights reserved.
43.	Edmund, J. M., et al. (författare) Optically stimulated luminescence from Al2O3 : C irradiated with 10-60 MeV protons 2007 Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 580:1, s. 210-213 Tidskriftsartikel (refereegranskat)abstract We investigated the potential use of Al2O3:C for medical proton dosimetry. Detector crystals coupled to fiber-optic cables were irradiated in proton beams with energies from 10 to 60 MeV. The key finding is that the initial intensity of the optically stimulated luminescence (OSL) signal is energy independent for small detectors (<0.5mm) and relatively small doses (<0.3Gy). This feature is related to the supralinearity of the detectors dose-response to low linear energy transfer (LET) radiation. The results show that our system can be used in medical proton dosimetry without LET-dependent correction factors in the dose and energy interval investigated. (c) 2007 Elsevier B.V. All rights reserved.
44.	Ekström, Andreas, et al. (författare) Determination of the isomeric fraction in a postaccelerated radioactive ion beam using the coupled decay-chain equations 2010 Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 614:2, s. 303-307 Tidskriftsartikel (refereegranskat)abstract A method based on the coupled decay-chain equations for extracting the isotopic and the isomeric composition of a postaccelerated radioactive ion beam is presented and demonstrated on a data set from a Coulomb excitation experiment. This is the first attempt of analyzing the content of a postaccelerated radioactive ion beam using this technique. The beam composition is required for an absolute normalization of the measurement. The strength of the method, as compared to present online-based methods, lies in the determination of the isomeric fraction of a partially isomeric beam using all data accumulated during the experiment. We discuss the limitations and sensitivity of the method with respect to the gamma-ray detection efficiency and the accumulated flux. (C) 2010 Elsevier B.V. All rights reserved.
45.	Eriksson, Mikael, et al. (författare) Some small-emittance light-source lattices with multi-bend achromats 2008 Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 587:2-3, s. 221-226 Tidskriftsartikel (refereegranskat)abstract Two examples of low-emittance light-source lattices are discussed. Both use similar building blocks consisting of 7-bend achromats. The small emittances generated by these lattices are further reduced by the introduction of insertion devices (IDs), resulting in beam emittance values ranging from 0.2 to 0.9 nm rad, depending on the number of achromats chosen. The two examples discussed here are rings with 12 and 20 achromats. The performances of any intermediate number of achromats can easily be estimated. A higher number of achromats of this type seems to result in an uncomfortably small dynamic aperture. The Touschek losses and Intra Beam Scattering (IBS) effect are calculated together with some means to reduce their impact. To calculate this impact, certain technical solutions are assumed, which are described. Other technical solutions could naturally be chosen. The impact of emittance on brilliance is also discussed and the brilliance curves for the two cases are presented and compared with the zero-emittance case ("ultimate source"). (C) 2008 Elsevier B.V. All rights reserved.
46.	Fritioff, T., et al. (författare) Purification of radioactive neutron-rich argon beams using an ion source in charge breeding mode 2006 Ingår i: Nuclear Instruments and Methods in Physics Research Section A. - : Elsevier BV. - 0168-9002 .- 1872-9576 .- 0167-5087. ; 556:1, s. 31-37 Tidskriftsartikel (refereegranskat)abstract Measurements of nuclear properties of some neutron-rich asymmetric fission isotopes at an ISOL laboratory present a severe problem when a plasma ion source is used as the primary ion-source. The problem is associated with intense multi-charged symmetric fission contaminants that cannot be mass-separated from asymmetric fission products. In this work we demonstrate how this problem can be overcome on-line by using an electron cyclotron resonance ion source (ECRIS) as a charge-breeding secondary ion-source. Mixed Ar+/Kr2+/Xe3+ radioactive beams from an plasma ion-source were injected into the PHOENIX ECRIS that currently is installed at the ISOLDE facility at CERN in order to improve the ratio of Ar to the background contaminants of Kr and Xe. The signal to noise ratio was improved by more than two orders of magnitude after charge-breeding and mass-separation of the Ar8+, Ar9+ beams. The information on the decay of the Ar-48 nucleus obtained in these tests is useful for a better understanding of the origin of the Ca-48/Ca-46 meteorite isotopic anomaly. Potential applications of the method are discussed.
47.	Ganenko, V., et al. (författare) Linearly polarized photon beam at MAX-lab 2014 Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 763, s. 137-149 Tidskriftsartikel (refereegranskat)abstract A linearly polarized photon beam has been produced at MAX-lab using the coherent bremsstrahlung of electrons with an energy of 192.6 MeV in a 0.1 mm thick diamond crystal. The intensity and shape of the coherent maxima and their dependence on the crystal orientation are similar to the features observed at higher electron energies (similar to 1 GeV) and are well described by coherent bremsstrahlung theory. The linear polarization of the uncollimated beam at the coherent peak energy approximate to 50-60 MeV is about 20% and can be increased to 40-45% if collimation of half the characteristic angle is used At present the degree of polarization is high enough to allow the study of polarization observables in photo-nuclear reactions at MAX-lab in the energy range from Giant Dipole Resonance up to approximate to 80 MeV. (C) 2014 Elsevier B.V. All rights reserved.
48.	Ghetti, Roberta, et al. (författare) Calibration of a neutron time-of-flight multidetector system for an intensity interferometry experiment 2004 Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 516:2-3, s. 492-501 Tidskriftsartikel (refereegranskat)abstract We present the details of an experiment on light particle interferometry. In particular, we focus on a time-of-flight technique which uses a cyclotron RF signal as a start and a liquid scintillator time signal as a stop, to measure neutron energy in the range of En approximate to 1.8-150 MeV. This dynamic range (up to 300 ns) is much larger than the beam bunch separation (54 ns) of the AGOR cyclotron (KVI). However, the problem of a short burst period is overcome by using the time information obtained from a fast projectile fragment phoswich detector. The complete analysis procedure to extract the final neutron kinetic energy spectra, is discussed. (C) 2003 Elsevier B.V. All rights reserved.
49.	Golubev, Pavel, et al. (författare) The Lund-York-Cologne Calorimeter (LYCCA): Concept, Design and Prototype Developments for a FAIR-NUSTAR Detector System to Discriminate Relativistic Heavy-ion Reaction Products 2013 Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 723, s. 55-66 Tidskriftsartikel (refereegranskat)abstract The concept, design and prototype developments for the Lund-York-Cologne CAlorimeter (LYCCA) is presented. LYCCA is a modular device for the NUclear STructure, Astrophysics and Reactions (NUSTAR) science pillar of the Facility for Antiproton and Ion Research (FAIR) at Darmstadt, Germany. LYCCA is designed to discriminate heavy ions produced in nuclear reactions induced by relativistic radioactive ion beams. Measurements of energy loss, total energy, and time-of-flight allow the derivation of proton number, Z, and mass number, A, of the reaction products. LYCCA-inherent tracking of the flight paths of the reaction products enables coincident High-resolution in-beam gamma-ray SPECtroscopy (HISPEC) of atomic nuclei far from the line of beta-stability. (C) 2013 Elsevier B.V. All rights reserved.
50.	Grabas, Herve, et al. (författare) RF strip-line anodes for Psec large-area MCP-based photodetectors 2013 Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - : Elsevier BV. - 0167-5087 .- 0168-9002. ; 711, s. 124-131 Tidskriftsartikel (refereegranskat)abstract We have designed and tested economical large-area RF strip-line anodes made by silk-screening silver onto inexpensive plate glass, for use in microchannel plate photodetectors to provide measurements of time, position, integrated charge, and pulse waveform shapes. The 229-mm-long anodes are modular, and can be attached in series for economy in electronics channel-count. Measurements of the anode impedance, bandwidth and cross-talk due to inter-strip coupling are presented. The analog bandwidth, a key determinant of timing resolution, decreases from 1.6 GHz to 0.4 GHz as the anode length increases from 289 mm to 916 mm. (C) 2013 Elsevier B.V. All rights reserved.

Skapa referenser, mejla, bekava och länka

Länka till träfflistan

Träfflista för sökning "L773:0168 9002 OR L773:0167 5087 "

Avgränsa träffmängd

År