| 1. |
- Agrell, Cecilia, et al.
(författare)
-
PCB congeners in precipitation, wash out ratios and depositional fluxes within the Baltic Sea region, Europe
- 2002
-
Ingår i: Atmospheric Environment. - 1352-2310. ; 36:2, s. 371-383
-
Tidskriftsartikel (refereegranskat)abstract
- Concentrations of PCB congeners were determined in precipitation and the annual and seasonal depositional fluxes were calculated for 16 (mostly rural) stations around the Baltic Sea during 1990-1993. The concentrations of individual congeners in precipitation were found to be influenced by atmospheric concentrations of PCBs, ambient temperature, precipitation volume and physico-chemical properties of the compounds. Median levels of PCBs in precipitation differed one order of magnitude between stations. When analyzing all data together to obtain regional trends, concentrations of PCBs in precipitation decreased with increasing temperature. This relationship was the same for all stations but differed in the magnitude of the slope for individual congeners. Low chlorinated PCB congeners showed steeper slopes for the temperature relationship than did high chlorinated congeners, a result explained by high atmospheric concentrations of the low chlorinated congeners during low temperatures. Annual wash out ratios were between 31 and 72 x 103 and tended to be higher for the high chlorinated congeners. Wash out ratios decreased with increasing temperature for all congeners except PCB-33. At snow scavenging events, the wash out ratio of PCBs increased with a factor of 2. Latitudinal trends for PCB concentrations in precipitation and deposition were generally not statistically significant. The calculated yearly deposition of PCBs to the Baltic Sea was 390 and 5-18 kg for individual congeners, with PCB-138 having the highest flux. Deposition of PCB congeners varied seasonally, with a factor between 2 and 3, and was generally highest during fall. Relatively higher deposition of low chlorinated congeners compared to high chlorinated congeners was found during winter. (C) 2002 Elsevier Science Ltd. All rights reserved.
|
|
| 2. |
- Backe, Cecilia, et al.
(författare)
-
Polychlorinated biphenyls in the air of southern Sweden - spatial and temporal variation
- 2000
-
Ingår i: Atmospheric Environment. - 1352-2310. ; 34:9, s. 1481-1486
-
Tidskriftsartikel (refereegranskat)abstract
- Polychlorinated biphenyls in the lower atmosphere were studied over a regional area covering approximately 11000 km(2) in southern Sweden. Sampling were performed in 1992-1993, continuously during one year, where samples from 11 sampling-sites (in all 260 samples) were analysed. PCB concentrations ranged over two order of magnitudes, 7-983 pg m(-3). Differences in PCB concentrations among the sampling sites revealed a large number of high-concentration outliers, mainly originating from one suburban site. Smaller differences in PCB concentrations between sites probably originated from varying geographical and meteorological conditions, that affected exchange processes between air and surfaces differently at the sampling sites. (C) 2000 Elsevier Science Ltd. All rights reserved.
|
|
| 3. |
- Berglund, Johan, et al.
(författare)
-
Manganese-Catalyzed Autoxidation of Dissolved Sulfur Dioxide in the Atmospheric Aqueous Phase
- 1995
-
Ingår i: Atmospheric Environment. - 1352-2310. ; 29:12, s. 1379-1391
-
Tidskriftsartikel (refereegranskat)abstract
- Autoxidation of SO2(aq) in the presence of manganese(II) is one of the important pathways for sulfuric acid formation in atmospheric clouds and fogs. Recent experimental results indicating that the catalyzed reaction takes place via a complex free-radical mechanism are discussed. Previous literature is reviewed in the light of this mechanism. Under atmospheric conditions of low total concentrations of manganese(II) ( < 2 × 10−5 M) and sulfur(IV) ( ≤ 10−5 M) and 2.5 < pH < 5, the rate law for conversion of SO2(aq) to SO3(aq) is reduced to d[S(IV)]/dt = k[Mn(II)][S(IV)], where [S(IV)] denotes the total concentration. A value of the overall rate constant k of 1.4 × 103 M−1s−1 is recommended for use in atmospheric model calculations.
|
|
| 4. |
- Brandt, Christian, et al.
(författare)
-
Role of Chromium and Vanadium in the Atmospheric Oxidation of Sulfur(IV)
- 1998
-
Ingår i: Atmospheric Environment. - 1352-2310. ; 32:4, s. 797-800
-
Tidskriftsartikel (refereegranskat)abstract
- Oxidation of HSO3- in aqueous solution has been studied in the presence of vanadium(V), chromium(III) and chromium(VI). Based on spectrophotometric kinetics data and product analysis it is concluded that the autoxidation rate of sulfur(IV) in slightly acidic solution is unaffected by the presence of vanadium(V) and chromium(III). Chromate(VI), on the other hand, oxidizes sulfur(IV) in a direct redox process in acidic solution. The overall rate of this reaction decreases with increasing pH and it becomes relatively slow in the atmospherically relevant pH range 4-6. Moreover, chromium(III) dominates strongly over chromium(VI) in the atmospheric aqueous phase. Hence, it is concluded that cations of vanadium vanadium and chromium have no significant influence on the atmospheric aqueous-phase oxidation of sulfur(IV) under most ambient atmospheric conditions. Only in very acidic droplets, direct redox between chromium(VI) and sulfite might be of some importance.
|
|
| 5. |
- Cederfelt, S. I., et al.
(författare)
-
Field validation of the droplet aerosol analyser
- 1997
-
Ingår i: Atmospheric Environment. - 1352-2310. ; 31:16, s. 2657-2670
-
Tidskriftsartikel (refereegranskat)abstract
- A new instrument for the study of cloud droplets and its relation to aerosol particles, the droplet aerosol analyser (DAA), was for the first time used in a field campaign. The DAA has the unique feature of measuring the ambient size of cloud droplets or cloud interstitial aerosol particles together with the size of its dry residue. This is obtained with a two-parameter data acquisition technique which results in a three-dimensional data set (ambient size, dry residue size, number concentration). The principle and design of the DAA is briefly described. The DAA was intercompared with differential mobility particle sizers, particulate volume monitors and a forward scattering spectrometer probe with respect to interstitial and cloud droplet dry residue size distribution as well as particle-size-dependent scavenging due to cloud droplet nucleation and for cloud droplet number concentration and size distribution and cloud liquid water concentration. Overall, the DAA showed good agreement with respect to all these six aerosol/cloud properties.
|
|
| 6. |
- Choularton, T. W., et al.
(författare)
-
The Great Dun Fell Cloud Experiment 1993 : An overview
- 1997
-
Ingår i: Atmospheric Environment. - 1352-2310. ; 31:16, s. 2393-2405
-
Tidskriftsartikel (refereegranskat)abstract
- The 1993 Ground-based Cloud Experiment on Great Dun Fell used a wide range of measurements of trace gases, aerosol particles and cloud droplets at five sites to study their sources and sinks especially those in cloud. These measurements have been interpreted using a variety of models. The conclusions add to our knowledge of air pollution, acidification of the atmosphere and the ground, eutrophication and climate change. The experiment is designed to use the hill cap cloud as a flow-through reactor, and was conducted in varying levels of pollution typical of much of the rural temperate continental northern hemisphere in spring-time.
|
|
| 7. |
- Ferrara, R, et al.
(författare)
-
Atmospheric mercury concentrations and fluxes in the Almaden District (Spain)
- 1998
-
Ingår i: Atmospheric Environment. - 1352-2310. ; 32:22, s. 3897-3904
-
Tidskriftsartikel (refereegranskat)abstract
- Atmospheric mercury levels around the world's largest mining and refining complex (Almaden, Spain) were determined during two field campaigns (September 1993 and February 1994) using both point monitors and lidar techniques. High mercury concentrations (0.1-5 mu g m(-3)) were measured over the village of Almaden in the prevailing wind direction. In the month of September the total mercury flux into the atmosphere was estimated to range from 600 to 1200 g h(-1). An attempt was made to measure the contribution from individual mercury sources. (C) 1998 Elsevier Science Ltd. All rights reserved.
|
|
| 8. |
- Gidhagen, L, et al.
(författare)
-
Model simulation of ultrafine particles inside a road tunnel
- 2003
-
Ingår i: Atmospheric Environment. - 1352-2310. ; 37:15, s. 2023-2036
-
Tidskriftsartikel (refereegranskat)abstract
- A monodispersive aerosol dynamic model, coupled to a 3D hydrodynamical grid model, has been used to study the dynamics of ultrafine particles inside a road tunnel in Stockholm, Sweden. The model results were compared to measured data of particle number concentrations, traffic intensity and tunnel ventilation rate. Coagulation and depositional losses to the tunnel walls were shown to be important processes during traffic peak hours, together contributing to losses of 77% of the particles smaller than 10nm and 41% of the particles of size 10-29nm. Particle growth due to water uptake or the presence of a micron-sized, resuspended particle fraction did not have any significant effect on the number of particles lost due to coagulation. Model simulation of particle number concentration response to temporal variations in traffic flow showed that constant emission factors could be used to reproduce the concentration variations of the particles larger than 29nm, while vehicle-speed-dependent factors are suggested to reproduce the variation of the smallest fractions. The emission factors for particle number concentrations estimated from the model simulation are in general higher and show a larger contribution from light-duty vehicles than what has been reported from a tunnel in California. The model study shows that combined measurements and model simulations in road tunnels can be used to improve the determinations of vehicle emission factors for ultrafine particles under realistic driving conditions. (C) 2003 Elsevier Science Ltd. All rights reserved.
|
|
| 9. |
- Gieray, R., et al.
(författare)
-
Phase partitioning of aerosol constituents in cloud based on single-particle and bulk analysis
- 1997
-
Ingår i: Atmospheric Environment. - 1352-2310. ; 31:16, s. 2491-2502
-
Tidskriftsartikel (refereegranskat)abstract
- Single-particle analysis, performed by laser microprobe mass spectrometry and bulk analytical techniques were used to study aerosol-cloud interactions within the third field campaign of the EUROTRAC subproject 'ground-based cloud experiments' at the Great Dun Fell, Cumbria, U.K. in spring 1993. The shape of the ridge made it possible for ground-based instrumentation to sample similar parcels of air before, during and after their transit through the cloud. A single jet five-stage minicascade impactor was used for sampling particles of the interstitial aerosol. A second impactor worked in tandem with a counter-flow virtual impactor and collected residues of cloud droplets. Considering marine conditions largest droplets nucleated on sea-salt particles, whereas smaller droplets were formed on sulphate and methane sulphonate containing particles. This clearly indicates chemical inhomogeneities in the droplet phase. Particles, which were disfavoured by droplet formation, often contained the highest amounts of water-insoluble carbonaceous matter. For the submicron size range we found that the carbonaceous matter was always internally mixed with sulphate. The fraction of carbonaceous matter increased with decreasing size. A detectable fraction of particles remained in the cloud interstitial air, although they were in size as well as in composition suitable to form cloud droplets. The findings confirm that nucleation is the most important process affecting phase partitioning in cloud, but that spatial and temporal variations of water vapour supersaturation have also an influence on the observed phase partitioning. Proton induced X-ray emission analysis and light absorption measurements of filter samples showed that the average scavenged fraction was 0.77 for sulphur and 0.57 for soot in clouds formed by continental influenced air and 0.62 and 0.44, respectively, for marine influenced clouds.
|
|
| 10. |
- Hedberg, E, et al.
(författare)
-
Chemical and physical characterization of emissions from birch wood combustion in a wood stove
- 2002
-
Ingår i: Atmospheric Environment. - 1352-2310. ; 36:30, s. 4823-4837
-
Tidskriftsartikel (refereegranskat)abstract
- The purpose of this study was to characterize the emissions of a large number of chemical compounds emitted from birch wood combustion in a wood stove. Birch wood is widely used as fuel in Swedish household appliances. The fuel load was held constant during six experiments. Particles < 2.5 mum diameter were collected and the size distribution of the particles was measured. The results were compared to the size distribution in road traffic emissions. It could be seen that the number distribution differed between the sources. In traffic exhaust, the number of particles maximized at 20 nm, while the number distribution from wood burning ranged from 20 to 300 nm. The ratio K/Ca on particles was found. to be significantly different in wood burning compared to road dust, range 30-330 for the former and 0.8+/-0.15 for the latter. The source profile of common elements emitted from wood-burning differed from that found on particles at a street-level site or in long-distance transported particles. The ratio toluene/benzene in this study was found to be in the range 0.2-0.7, which is much lower than the ratio 3.6+/-0.5 in traffic exhaust emissions. Formaldehyde and acetone were the most abundant compounds among the volatile ketones and aldehydes. The emission factor varied between 180-710mg/kg wood for formaldehyde and 5-1300mg/kg wood for acetone. Of the organic acids analyzed (3,4,5)-trimethoxy benzoic acid was the most abundant compound. Of the PAHs reported, fluorene, phenanthrene, anthracene, fluoranthene and pyrene contribute to more than 70% of the mass of PAH. Of the elements analyzed, K and Si were the most abundant elements, having emission factors of 27 and 9mg/kg wood, respectively. Although fluoranthene has a toxic equivalence factor of 5% of benzo(a)pyrene (B(a)P), it can be seen that the toxic potency of fluoranthene in wood burning emissions is of the same size as B(a)P. This indicates that the relative carcinogenic potency contribution of fluoranthene in wood smoke would be about 40% of B(a)P. (C) 2002 Elsevier Science Ltd. All rights reserved.
|
|
| 11. |
- Ketzel, M, et al.
(författare)
-
Particle and trace gas emission factors under urban driving conditions in Copenhagen based on street and roof-level observations
- 2003
-
Ingår i: Atmospheric Environment. - 1352-2310. ; 37:20, s. 2735-2749
-
Tidskriftsartikel (refereegranskat)abstract
- Simultaneous measurements of particle size distribution (size/range 10-700 nm) inside an urban street canyon and a nearby urban background location in Copenhagen in May-November 2001 were used to separate the traffic source contribution in the street canyon from the background levels. The background concentrations are highly variable due to changing contributions from long-range transport and local sources showing a diurnal pattern with a shift to smaller particle sizes during midday hours. The average ratio background/street concentration is 0.26 for NOx and 0.35, 0.42, 0.60, 0.64, respectively, for CO, total particle number (ToN), surface and volume. The particle size distribution of the traffic source shows during daytime and evening hours (6-24) a maximum at particle sizes of 20-30 nm independent of the changing heavy-duty vehicle share during the same time interval. The particle number concentration highly correlated (R > 0.83) with NOx through a wide range of particle sizes. The method of inverse modelling was applied to estimate average fleet emission factors typical of urban conditions in Denmark. Emission factors per average vehicle were estimated as (2.8 +/- 0.5) x 10(14) particles/km, (1.3 +/- 0.2) g NOx/(veh km) and (11 +/- 2) g CO/(veh km). We observe two types of 'nanoparticle events' (a) in background, probably due to photochemistry and (b) in the night hours when traffic is dominated by diesel taxis. During night hours (0-5), the maximum in the emitted particle size distribution, is shifted to smaller sizes of about 15-18 nm. This shift to smaller particle sizes is related to an increase in the average NOx and ToN emission per vehicle by a factor of 2-3 and a reduced CO emission also by a factor of 2-3. (C) 2003 Elsevier Science Ltd. All rights reserved.
|
|
| 12. |
- Martinsson, B. G., et al.
(författare)
-
Experimental determination of the connection between cloud droplet size and its dry residue size
- 1997
-
Ingår i: Atmospheric Environment. - 1352-2310. ; 31:16, s. 2477-2490
-
Tidskriftsartikel (refereegranskat)abstract
- The droplet activation process and droplet growth was studied during early stages of the formation of orographically-induced clouds. The experimental results were compared with the results obtained with a closed parcel, adiabatic cloud model. Good agreement was in most cases found between model and measurements with respect to cloud droplet number concentration, cloud droplet solute concentration and particle sizes scavenged due to cloud droplet nucleation. The experimental results were mainly obtained with a new instrument, the droplet aerosol analyser (DAA), which allows the determination of ambient sizes of cloud droplets and interstitial aerosol particles directly connected with the size of its dry residue in a two-parameter data acquisition. The resulting three-dimensional data set (ambient size, dry size, number concentration) was utilised to determine several cloud/aerosol properties, whereof some unique.
|
|
| 13. |
- Svenningsson, Birgitta, et al.
(författare)
-
Cloud droplet nucleation scavenging in relation to the size and hygroscopic behaviour of aerosol particles
- 1997
-
Ingår i: Atmospheric Environment. - 1352-2310. ; 31:16, s. 2463-2475
-
Tidskriftsartikel (refereegranskat)abstract
- The size distributions and hygroscopic growth spectra of aerosol particles were measured during the GCE cloud experiment at Great Dun Fell in the Pennine Hills in northern England. Hygroscopic growth is defined as the particle diameter at 90% RH divided by the particle diameter at 10% RH. The fraction of the aerosol particles scavenged by cloud droplets as a function of particle size was also measured. The general aerosol type was a mixture of marine and aged anthropogenic aerosols. The Aitken and accumulation mode numbers (average ± 1 S.D.) were 1543 ± 1078 and 1023 ± 682 cm-3, respectively. The mean diameters were in the range 30-100 nm and 100-330 nm. The hygroscopic growth spectra were bimodal about half the time. The less-hygroscopic particles had average growth factors of 1.06, 1.06; 1.03, 1.03, and 1.03 for particle diameters of 50, 75, 110, 165, and 265 nm, respectively. For the more-hygroscopic particles of the same sizes, the average hygroscopic growth was 1.34, 1.37, 1.43, 1.47, and 1.53. The effects of ageing on the aerosol particle size distribution and on hygroscopic behaviour are discussed. The scavenged fraction of aerosol particles was a strong function of particle diameter. The diameter with 50% scavenging was in the range 90-220 nm. No tail of smaller particles activated to cloud drops was observed. A small tail of larger particles that remained in the interstitial aerosol can be explained by there being a small fraction of less-hygroscopic particles. A weak correlation between the integral dry particle diameter and the diameter with 50% scavenging was seen.
|
|
| 14. |
- Swietlicki, Erik, et al.
(författare)
-
Source identification during the Great Dun Fell Cloud Experiment 1993
- 1997
-
Ingår i: Atmospheric Environment. - 1352-2310. ; 31:16, s. 2441-2451
-
Tidskriftsartikel (refereegranskat)abstract
- A characterisation of the sources influencing the site for the final field campaign of the EUROTRAC subproject GCE (Ground-based Cloud Experiment) at Great Dun Fell, Cumbria, Great Britain in April-May 1993 is presented. The sources were characterised mainly by means of aerosol filter and cascade impactor data, single particle analysis, gas data, data on aromatic organic compounds, cloud water ionic composition, measurements of aerosol size distributions and hygroscopic properties and various meteorological information. Receptor models applied on the aerosol filter and impactor data sets separately revealed two major source types being a marine sea spray source and a long-range transported anthropogenic pollution source. The results of the receptor models were largely consistent with the other observations used in the source identification. Periods of considerable anthropogenic pollution as well as almost pure marine air masses were clearly identified during the course of the experiment.
|
|
| 15. |
- Swietlicki, Erik, et al.
(författare)
-
Urban air pollution source apportionment using a combination of aerosol and gas monitoring techniques
- 1996
-
Ingår i: Atmospheric Environment. - : Elsevier BV. - 1352-2310. ; 30:15, s. 2795-2809
-
Tidskriftsartikel (refereegranskat)abstract
- The dominating local and regional sources of gaseous and particulate air pollution in the city of Lund (69,000 inhabitants) in southern Sweden were characterized using a combination of aerosol and gas-phase monitoring techniques. Twelve-hour samples were taken at two stations of both fine and coarse fraction urban aerosols with a stacked filter unit during the four-week measurement campaign in March/April 1993. The aerosol samples were analysed with PIXE for 14 major and trace elements. In addition, gaseous species (SO2, NO2, O-3) were measured simultaneously with the DOAS technique over two stretches, crossing each other only 300 m from the downtown aerosol sampling site. The combined results obtained by the analytical techniques PIXE and DOAS for aerosol and gas measurements, respectively, were used in an absolute receptor model in order to identify the major sources affecting the measurement sites and to apportion the measured air pollutants to the identified sources. The gases (SO2, NO2, O-3) could also be attributed to specific sources by combining the trace elemental concentration data for the fine fraction aerosol with that of the gaseous species in the receptor model. According to the absolute principal component analysis (APCA) model, the dominant sources for the measured species were resuspended road dust, automobile and diesel emissions, combustion of oil and coal, ferrous and non-ferrous smelters and sea spray. Of these, the sources related to traffic are mainly local in character while the others constitute a regional background. For a small city in southern Scandinavia like Lund with only light industry, the long-range transported air pollutants make up a significant part of the fine fraction aerosol. (C) 1996 Elsevier Science Ltd
|
|
| 16. |
- ter Schure, Arnout, et al.
(författare)
-
Polybrominated diphenyl ethers in precipitation in Southern Sweden (Skane, Lund)
- 2002
-
Ingår i: Atmospheric Environment. - 1352-2310. ; 36:25, s. 4015-4022
-
Tidskriftsartikel (refereegranskat)abstract
- The presence of polybrominated diphenyl ether (PBDE) flame retardants in total deposition (wet + dry) was assessed with the simultaneous use of three bulk samplers during a 2 week period. The particle associated and the 'dissolved' phase were separated during sampling. Volume weighted mean (VWM) concentrations of SigmaPBDE (9 congeners) in rain were 209 pg l(-1). Total deposition rates were 2 +/- 1 ng SigmaPBDE m(-2) day(-1). The total PBDE deposition was dominated by decaBDE(209) and thereafter 2,2'4,4'-tetraBDE(47) and 2,2'4,4',5-pentaBDE(99). Concentrations of particle associated and 'dissolved' PBDEs in total deposition were used to calculate filter/adsorbent ratios (F/A). We found that 65 +/- 18% of the total PBDEs were particle associated. Low F/A ratios for higher brominated congeners (Br > 5) were observed. This is contradictory with predictions based on the PBDEs' physico-chemical properties and was attributed to sampling artefacts, such as particle size distribution, and/or non-equilibrium processes. There was a negative relationship between the particulate SigmaPBDE concentration and rain volume suggesting a dilution effect and the importance of particle scavenging for wet deposition of PBDEs. (C) 2002 Elsevier Science Ltd. All rights reserved.
|
|
| 17. |
|
|
| 18. |
- Ekberg, Lars, 1962
(författare)
-
Volatile organic compounds in office buildings
- 1993
-
Ingår i: Atmospheric Environment. - 1873-2844 .- 1352-2310. ; 28:22, s. 3571-3575
-
Tidskriftsartikel (refereegranskat)abstract
- This paper concerns field measurements of volatile organic compounds (VOCs) in five office buildings. The buildings were selected to represent buildings without obvious problems with regard to the indoor air quality. The total concentrations of VOCs (TVOC) were measured using two different detection principles. Both short-term measurements and continuous monitoring were carried out. The results show that the use of continuous TVOC monitoring can provide valuable information in addition to the results obtained by sampling. The indoor TVOC concentrations obtained by gas chromatography ranged from 0.16 to 0.35 mgm−3. The indoor-outdoor TVOC concentration difference obtained by photoacoustic spectroscopy was about twice as high during working hours as during the night time. Furthermore, it is indicated that VOCs in indoor environments do not only originate from construction materials and other internal sources. Outdoor sources can also have a substantial influence on the indoor VOC concentrations.
|
|
| 19. |
- Fick, Jerker, et al.
(författare)
-
A study of the gas-phase ozonolysis of terpenes: the impact of radicals formed during the reaction
- 2002
-
Ingår i: Atmospheric Environment. - 1352-2310 .- 1873-2844. ; 36:20, s. 3299-3308
-
Tidskriftsartikel (refereegranskat)abstract
- The gas-phase ozonolysis of α-pinene, Δ3-carene and limonene was investigated at ppb levels and the impact of the ozone, relative air humidity (RH), and time was studied using experimental design. The amounts of terpene reacted varied in the different settings and were as high as 8.1% for α-pinene, 10.9% forΔ3-carene and 23.4% for limonene. The designs were able to describe almost all the variation in the experimental data and were also successful in predicting omitted values. The results described the effects of time and ozone and also showed that RH did not have a statistically significant effect on the ozonolysis. The results also showed that all three terpenes were affected by an additional oxidation of OH radicals and/or other reactive species. The results from the designs states that this additional oxidation was responsible for 40% of the total amount of α-pinene reacted, 33% of the total amount of Δ3-carene reacted and 41% of the total amount of limonene reacted at the settings 20 ppb terpene, 75 ppb ozone, 20% RH and a reaction time of 213 s. Additional experiments with 2-butanol as OH radical scavenger showed that the reaction with OH radicals was responsible for 37% of the total α-pinene reacted and 39% of the total Δ3-carene reacted at the same settings. The scavenger experiments also showed that there were no significant amounts of OH radicals formed during the ozonolysis of limonene. The results from the designs were also compared to a mathematical model in order to evaluate further the data.
|
|
| 20. |
|
|
| 21. |
- Janhäll, Sara, et al.
(författare)
-
Vertical distribution of air pollutants at the Gustavii Cathedral in Göteborg, Sweden
- 2003
-
Ingår i: Atmospheric Environment. - : Elsevier. - 1352-2310 .- 1873-2844. ; 37:2, s. 209-217
-
Tidskriftsartikel (refereegranskat)abstract
- Atmospheric trace gases and particles were measured at two heights at the Gustavii Cathedral in Göteborg, Sweden, during 7 weeks in September and October 1999. The Gustavii Cathedral is situated in the city centre of Göteborg, which is near the harbour area and encircled by heavy traffic some hundred metres away. The main body of the church is as high as the surrounding buildings, while the tower extends well above. The sampling points were placed on the west wall of the tower at 10 and 32 meter height, i.e. well below and above the roof top level of surrounding buildings, respectively.Sulphur dioxide and nitric acid were sampled using the denuder technique and analysed by Ion Chromatography, IC. Total suspended particulates (TSP) were sampled using filter cups and subsequently analysed by energy dispersive X-ray fluorescence spectroscopy (EDXRF). In addition to the diurnal sampling of species, nitrogen oxides were measured using chemiluminescence detectors. Additional data from the Environmental Office in Göteborg was used in the analysis.Differences between the concentrations measured at the upper and lower levels were calculated and their variation and dependence on meteorological factors were evaluated. On the average larger concentrations were found at the lower level for soil derived elements and TSP, while nitric acid and nitric oxide showed larger concentrations at the upper level. Sulphur dioxide and nitrogen dioxide, as well as many of the elements in the TSP, showed equal concentrations at the two levels. However, depending on wind direction the measured differences of nitrogen oxides could be both positive and negative.
|
|
| 22. |
|
|
| 23. |
- Libiseller, Claudia, 1975-, et al.
(författare)
-
Model selection for local and regional meteorological normalisation of background concentrations of tropospheric ozone
- 2003
-
Ingår i: Atmospheric Environment. - 1352-2310 .- 1873-2844. ; 37:28, s. 3923-3931
-
Tidskriftsartikel (refereegranskat)abstract
- Meteorological normalisation of time series of air quality data aims to extract anthropogenic signals by removing natural fluctuations in the collected data. We showed that the currently used procedures to select normalisation models can cause over-fitting to observed data and undesirable smoothing of anthropogenic signals. A simulation study revealed that the risk of such effects is particularly large when: (i) the observed data are serially correlated, (ii) the normalisation model is selected by leave-one-out cross-validation, and (iii) complex models, such as artificial neural networks, are fitted to data. When the size of the test sets used in the cross-validation was increased, and only moderately complex linear models were fitted to data, the over-fitting was less pronounced. An empirical study of the predictive ability of different normalisation models for tropospheric ozone in Finland confirmed the importance of using appropriate model selection strategies. Moderately complex regional models involving contemporaneous meteorological data from a network of stations were found to be superior to single-site models as well as more complex regional models involving both contemporaneous and time-lagged meteorological data from a network of stations.
|
|
| 24. |
- Molnár, Peter, 1967, et al.
(författare)
-
Roadside measurements of fine and ultrafine particles at a major road north of Gothenburg
- 2002
-
Ingår i: Atmospheric Environment. - 1352-2310 .- 1873-2844. ; 36:25, s. 4115-4123
-
Tidskriftsartikel (refereegranskat)abstract
- Particle measurements were conducted at a road site 15 km north of the city of Gothenburg for 3 weeks in June 2000. The size distribution between 10 and 368 nm was measured continuously by using a differential mobility particle sizer (DMPS) system. PM2.5 was sampled on a daily basis with subsequent elemental analysis using EDXRF-spectroscopy. The road is a straight four-lane road with a speed limit of 90 kph. The road passing the site is flat with no elevations where the vehicles run on a steady workload and with constant speed. The traffic intensity is about 20,000 cars per workday and 13,000 vehicles per day during weekends. The diesel fuel used in Sweden is low in sulphur content (< 10 ppm) and therefore the diesel vehicles passing the site contribute less to particle emissions in comparison with other studies. A correlation between PM2.5 and accumulation mode particles (100-368 nm) was observed. However, no significant correlation was found between number concentrations of ultrafine particles (10-100 nm) and PM2.5 or the accumulation mode number concentration. The particle distribution between 10 and 368 nm showed great dependency on wind speed and wind direction, where the wind speed was the dominant factor for ultrafine (10-100nm) particle concentrations. The difference in traffic intensity between workday and weekend together with wind data made it possible to single out the traffic contribution to particle emissions and measure the size distribution. The results presented in combination with previous studies show that both PM2.5 and the mass of accumulation mode particles are bad estimates for ultrafine particles. (C) 2002 Elsevier Science Ltd. All rights reserved.
|
|
| 25. |
|
|
| 26. |
- Pommer, Linda, et al.
(författare)
-
Development of a NO2 scrubber for accurate sampling of ambient levels of terpenes
- 2002
-
Ingår i: Atmospheric Environment. - 1352-2310 .- 1873-2844. ; 36:9, s. 1443-1452
-
Tidskriftsartikel (refereegranskat)abstract
- The result of pumping air containing 56 ppb NO2 through a terpene-spiked adsorbent (90–130 ng, 90–100 ml min−1), Tenax TA, for 20 min (1.8–2.0 l) was that 8% of α-pinene, 7% of β-pinene, 21% of Δ3-carene and 5% of limonene were oxidised. In similar experiments with air containing 56 ppb O3, 3% of α-pinene, 4% of β-pinene, 10% of Δ3-carene and 38% of limonene were oxidised. Sampling a mixture of a terpene and NO2 using Tenax TA can give unwanted overestimation of the amount of reaction products from the terpene–NO2 reaction or underestimation of the original terpene levels. A scrubber was needed to reduce the problems caused by interfering reactions on the adsorbent of NO2 and to reduce discrimination of reactive compounds due to their relatively fast decay on the adsorbent. Several chemicals have been tested for their ability of removing NO2 and our objective was to develop a well functioning, reusable, easy to handle, easy manufactured NO2 scrubber. The result of the experiments was a scrubber consisting of two glass fibre filters coated with Na2SO3 assembled in a dust collector. The recovery of the terpenes through the scrubber varied between 75% and 97% at 15–75% relative humidity, and the scrubber is a one-use scrubber due to memory effects. The Na2SO3 scrubber could be stored in room air for at least one month without loosing the capacity of removing NO2.
|
|
| 27. |
|
|
| 28. |
- Wingfors, Håkan, et al.
(författare)
-
Characterisation and determination of profiles of polycyclic aromatic hydrocarbons in a traffic tunnel in Gothenburg, Sweden
- 2001
-
Ingår i: Atmospheric Environment. - 1352-2310 .- 1873-2844. ; 35:36, s. 6361-6369
-
Tidskriftsartikel (refereegranskat)abstract
- The concentrations of semi-volatile polycyclic aromatic hydrocarbons (PAHs), hydrocarbons (HCs), particulate matter (PM 1, 2.5 and 10 μm) and total suspended particles (TSPs) were measured in a traffic tunnel in Gothenburg, Sweden. Emission factors (EFs) were also calculated. These variables are assumed to provide good estimates of average vehicle emissions, since all types of vehicle, using all types of fuel, pass through this tunnel. It was shown that the majority of particle-associated PAHs were found on particles with an aerodynamic diameter of <1 μm. The concentrations of PAHs were one order higher in magnitude in air samples from the tunnel than in air samples at two urban locations. However, the PAH profiles of air samples from the tunnel and the urban sites were similar. This was demonstrated using principal component analysis (PCA). Finally, and notably, there was no significant change in the total emissions when the proportion of heavy-duty vehicles (HDVs) increased from 8% to 24%. Previously, diesel vehicles had been found to release larger quantities of PAHs and related substances. Advances in fuel quality, and HDV motor and exhaust system design during the last decade may have contributed to this promising result. However, it was shown, using partial least squares regression to latent structures (PLS), that some of the parameters measured displayed correlations with the proportions of HDVs and light-duty vehicles (LDVs). Concentrations of total HCs, TSPs, dibenzothiopene, phenantrene, anthracene and monomethyl-derivatives of phenantrene and anthracene were all correlated to the proportion of HDVs. The concentrations of naphthalene, some mono- and dimethylnaphthalenes and most large PAHs (with 5–7 fused rings) were correlated to the proportion of LDVs.
|
|
| 29. |
- Adachi, Kouji, et al.
(författare)
-
Composition and mixing state of individual aerosol particles from northeast Greenland and Svalbard in the Arctic during spring 2018
- 2023
-
Ingår i: Atmospheric Environment. - 1352-2310 .- 1873-2844. ; 314
-
Tidskriftsartikel (refereegranskat)abstract
- The Arctic region is warming about four times faster than the rest of the globe, and thus it is important to understand the processes driving climate change in this region. Aerosols are a significant component of the Arctic climate system as they form ice crystals and liquid droplets that control the dynamics of clouds and also directly interact with solar radiation, depending on the compositions and mixing states of individual particles. Here, we report on the characteristics of submicron-sized aerosol particles using transmission electron microscopy obtained at two high Arctic sites, northeast Greenland (Villum Research Station) and Svalbard (Zeppelin Observatory), during spring 2018. The results showed that a dominant compound in the submicron-sized spring aerosols was sulfate, followed by sea salt particles. Both model simulations and observations at the Zeppelin Observatory showed that sea salt particles became more prevalent when low-pressure systems passed by the station. Model simulations indicate that both sampling sites were affected by diffused and diluted long-range transport of anthropogenic aerosols from lower latitudes with negligible influences of biomass burning emissions during the observation period. Overall, the composition of measured aerosol particles from the two Arctic sites was generally similar and showed no apparent variation except for the sea salt fractions. This study shows a general picture of high Arctic aerosol particles influenced by marine sources and diffused long-range transport of anthropogenic sources during the Arctic spring period. These results will contribute to a better knowledge of the aerosol composition and mixing state during the Arctic spring, which helps to understand the contributions of aerosols to the Arctic climate.
|
|
| 30. |
- Agrell, Cecilia, et al.
(författare)
-
Polybrominated diphenyl ethers (PBDES) at a solid waste incineration plant I: Atmospheric concentrations
- 2004
-
Ingår i: Atmospheric Environment. - : Elsevier BV. - 1352-2310. ; 38:30, s. 5139-5148
-
Tidskriftsartikel (refereegranskat)abstract
- In the first of two papers, the atmospheric poly brominated diphenyl ether (PBDE) concentrations at a municipal solid waste incineration (MSW) plant with electronic recycling is compared with that at an industrial urban reference site producing asphalt and concrete. In the second paper, atmospheric deposition and washout behaviour is presented (Atmos. Environ. (2004a)). PBDEs (BDE28, -47, -66, -100, -154, -153, -183, -209) in the gaseous and particulate phase were measured with high resolution in time during the colder parts of the year to minimise the influence of potential historical pollution at the sites through volatilisation. This also means that reported levels are lower compared to other reported data. Results of BDE47 (TetraBDE) and BDE209 (DecaBDE) as representatives of "old" vs. "new" PBDEs as well as SigmaPBDE, excluding BDE209, are presented. Median SigmaPBDE, BDE47 and BDE209 concentration were 6.3, 2.1 and 10.4 pg m(-3) at the MSW and 3.5, 1.7 and 6.5 pg m-3 at the reference site. The total concentrations (gaseous and particulate phase) were significantly higher at the MSW compared to the reference site for SigmaPBDE and BDE47 but not for BDE209. The same results were obtained regarding concentrations in the gaseous phase. Particle concentrations were significantly higher at the MSW for SigmaPBDE, BDE47 and BDE209. Within each site, the gaseous-phase concentration was significantly higher than the particulate-phase concentration except for BDE209 at the MSW. Thus, the proportion of BDE209 detected in the particulate phase was higher at the MSW compared to the reference site. Together with the results of the second paper, we suggest that treatment of waste is presently a source of "old" PBDEs to the environment, whereas the rather similar BDE209 concentrations at the two sites are more a result of proximity to potential diffuse sources.
|
|
| 31. |
- Ahlberg, Erik, et al.
(författare)
-
Secondary organic aerosol from VOC mixtures in an oxidation flow reactor
- 2017
-
Ingår i: Atmospheric Environment. - : Elsevier BV. - 1352-2310. ; 161, s. 210-220
-
Tidskriftsartikel (refereegranskat)abstract
- The atmospheric organic aerosol is a tremendously complex system in terms of chemical content. Models generally treat the mixtures as ideal, something which has been questioned owing to model-measurement discrepancies. We used an oxidation flow reactor to produce secondary organic aerosol (SOA) mixtures containing oxidation products of biogenic (α-pinene, myrcene and isoprene) and anthropogenic (m-xylene) volatile organic compounds (VOCs). The resulting volume concentration and chemical composition was measured using a scanning mobility particle sizer (SMPS) and a high-resolution time-of-flight aerosol mass spectrometer (HR-ToF-AMS), respectively. The SOA mass yield of the mixtures was compared to a partitioning model constructed from single VOC experiments. The single VOC SOA mass yields with no wall-loss correction applied are comparable to previous experiments. In the mixtures containing myrcene a higher yield than expected was produced. We attribute this to an increased condensation sink, arising from myrcene producing a significantly higher number of nucleation particles compared to the other precursors. Isoprene did not produce much mass in single VOC experiments but contributed to the mass of the mixtures. The effect of high concentrations of isoprene on the OH exposure was found to be small, even at OH reactivities that previously have been reported to significantly suppress OH exposures in oxidation flow reactors. Furthermore, isoprene shifted the particle size distribution of mixtures towards larger sizes, which could be due to a change in oxidant dynamics inside the reactor.
|
|
| 32. |
- Ahmed, Trifa M., et al.
(författare)
-
Native and oxygenated polycyclic aromatic hydrocarbons in ambient air particulate matter from the city of Sulaimaniyah in Iraq
- 2015
-
Ingår i: Atmospheric Environment. - : Elsevier BV. - 1352-2310 .- 1873-2844. ; 116, s. 44-50
-
Tidskriftsartikel (refereegranskat)abstract
- The concentrations of 43 polycyclic aromatic hydrocarbons (PAHs) and 4 oxygenated PAHs (OPAHs) are reported for the first time in particulate matter (PM10) sampled in the air of the city of Sulaimaniyah in Iraq. The total PAH concentration at the different sampling sites varied between 9.3 and 114 ng/m(3). The corresponding values of the human carcinogen benzotalpyrene were between 0.3 and 6.9 ng/m(3), with most samples exceeding the EU annual target value of 1 ng/m(3). The highly carcinogenic dibenzopyrene isomers dibenzo[a,l]pyrene, dibenzo[a,e]pyrene, dibenzo[a,i]pyrene and dibenzo[a,h]pyrene constituted 0.1-0.4% of the total PAH concentration. However, when scaling for relative cancer potencies using toxic equivalency factors, a benzo[a]pyrene equivalent concentration of dibenzo[a,l]pyrene equal to that of benzo[a]pyrene was obtained, indicating that the contribution of dibenzo[a,l]pyrene to the carcinogenicity of the PAHs could be similar to that of benzo[a]pyrene. A high correlation between the determined concentrations of the dibenzopyrene isomers and benzo[a]pyrene was found, which supported the use of benzo[a]pyrene as an indicator for the carcinogenicity of PAHs in ambient air. The total concentrations of the four OPAHs, 9,10-anthraquinone, 4H-cyclopenta[def]phenanthren-4-one, benzanthrone, and 7,12-benz[a]anthraquinone, varied between 0.6 and 8.1 ng/m(3), with 9,10-anthraquinone being the most abundant OPAH in all of the samples.
|
|
| 33. |
- Ahn, Seo H., et al.
(författare)
-
Relationship between cloud condensation nuclei (CCN) concentration and aerosol optical depth in the Arctic region
- 2021
-
Ingår i: Atmospheric Environment. - : Elsevier BV. - 1352-2310 .- 1873-2844. ; 267
-
Tidskriftsartikel (refereegranskat)abstract
- To determine the direct and indirect effects of aerosols on climate, it is important to know the spatial and temporal variations in cloud condensation nuclei (CCN) concentrations. Although many types of CCN measurements are available, extensive CCN measurements are challenging because of the complexity and high operating cost, especially in remote areas. As aerosol optical depth (AOD) can be readily observed by remote sensing, many attempts have been made to estimate CCN concentrations from AOD. In this study, the CCN-AOD relationship is parameterized based on CCN ground measurements from the Zeppelin Observatory (78.91 degrees N, 11.89 degrees E, 474 m asl) in the Arctic region. The AOD measurements were obtained from the Ny-Alesund site (78.923 degrees N, 11.928 degrees E) and Modern-Era Retrospective Analysis for Research and Applications, Version 2 reanalysis. Our results show a CCN-AOD correlation with a coefficient of determination R-2 of 0.59. Three additional estimation models for CCN were presented based on the following data: (i) in situ aerosol chemical composition, (ii) in situ aerosol optical properties, and (iii) chemical composition of AOD obtained from reanalysis data. The results from the model using in situ aerosol optical properties reproduced the observed CCN concentration most efficiently, suggesting that the contribution of BC to CCN concentration should be considered along with that of sulfate.
|
|
| 34. |
- Ahrens, Lutz
(författare)
-
Concentrations in air of organobromine, organochlorine and organophosphate flame retardants in Toronto, Canada
- 2014
-
Ingår i: Atmospheric Environment. - : Elsevier BV. - 1352-2310. ; 99, s. 140-147
-
Tidskriftsartikel (refereegranskat)abstract
- Concentrations of organobromine (BFRs), organochlorine (CFRs) and organophosphate esters flame retardants and plasticizers (PFRs) in air were monitored for over one year at an urban site in Toronto, Canada during 2010-2011. The mean value for polybrominated diphenyl ethers (BDEs) (gas + particle phase) was 38 pg/m(3) with BDE-47 and BDE-99 as the dominant congeners. The mean concentrations in air for Sigma non-BDE (BFRs and CFRs), was 9.6 pg/m(3) about four times lower than the BDEs. The brominated FRs: TBP-AE, BTBPE, EH-TBB, BEH-TEBP and the chlorinated syn- and anti-DP were detected frequently, ranging from 87% to 96%. Highest concentrations in air among all flame retardant classes were observed for the Sigma-PFRs. The yearly mean concentration in air for EPFRs was 2643 pg/m(3) with detection frequency higher than 80%. Except for TBP-AE and b- DBE-DBCH, non-BDEs (BFRs, CFRs and PFRs) were mainly associated with the particle phase. BDE concentrations in air were positively correlated with temperature indicating that volatilization from local sources was an important factor controlling levels in air. This correlation did not hold for most BFRs, CFRs and PFRs which were mainly on particles. For these compounds, air concentrations in Toronto are likely related to emissions from point sources and advective inputs. This study highlights the importance of urban air monitoring for FRs. Urban air can be considered a sentinel for detecting changes in the use and application of FRs in commercial products. Crown Copyright (C) 2014 Published by Elsevier Ltd. All rights reserved.
|
|
| 35. |
- Alves, C. A., et al.
(författare)
-
Physical and chemical properties of non-exhaust particles generated from wear between pavements and tyres
- 2020
-
Ingår i: Atmospheric Environment. - : Elsevier Ltd. - 1352-2310 .- 1873-2844. ; 224
-
Tidskriftsartikel (refereegranskat)abstract
- A road simulator was used to generate wear particles from the interaction between two tyre brands and a composite pavement. Particle size distributions were monitored using a scanning mobility particle sizer and an aerosol particle sizer. Continuous measurements of particle mass concentrations were also made. Collection of inhalable particles (PM10) was conducted using a high-volume sampler equipped with quartz filters, which were then analysed for organic and elemental carbon, organic constituents and elemental composition. Tyre fragments chopped into tiny chips were also subjected to detailed organic and elemental speciation. The number concentration was dominated by particles <0.5 μm, whereas most of the mass was found in particles >0.5 μm. The emission factor from wear between pavements and tyres was of the order of 2 mg km−1 veh−1. Organic carbon represented about 10% of the PM10 mass, encompassing multiple aliphatic compounds (n-alkanes, alkenes, hopanes, and steranes), PAHs, thiazols, n-alkanols, polyols, some fragrant compounds, sugars, triterpenoids, sterols, phenolic constituents, phthalate plasticisers and several types of acids, among others. The relationship between airborne particulate organic constituents and organic matter in tyre debris is discussed. The detection of compounds that have been extensively used as biomass burning tracers (e.g. retene, dehydroabietic acid and levoglucosan) in both the shredded tiny tyre chips and the wear particles from the interaction between tyres and pavement puts into question their uniqueness as markers of wood combustion. Trace and major elements accounted for about 5% of the mass of the tyre fragments but represented 15–18% of the PM10 from wear, denoting the contribution of mineral elements from the pavement. Sulphur and zinc were abundant constituents in all samples.
|
|
| 36. |
- Alves, Celia, et al.
(författare)
-
Organic compounds in aerosols from selected European sites - Biogenic versus anthropogenic sources
- 2012
-
Ingår i: Atmospheric Environment. - : Elsevier BV. - 1352-2310. ; 59, s. 243-255
-
Tidskriftsartikel (refereegranskat)abstract
- Atmospheric aerosol samples from a boreal forest (Hyytiala, April 2007), a rural site in Hungary (K-puszta, summer 2008), a polluted rural area in Italy (San Pietro Capofiume, Po Valley, April 2008), a moderately polluted rural site in Germany located on a meadow (Melpitz, May 2008), a natural park in Spain (Montseny, March 2009) and two urban background locations (Zurich, December 2008, and Barcelona, February/March 2009) were collected. Aliphatics, polycyclic aromatic hydrocarbons, carbonyls, sterols, n-alkanols, acids, phenolic compounds and anhydrosugars in aerosols were chemically characterised by gas chromatography-mass spectrometry, along with source attribution based on the carbon preference index (CPI), the rations between the unresolved and the chromatographically resolved aliphatics, the contribution of wax n-alkanes, n-alkanols and n-alkanoic acids from plants, diagnostic ratios of individual target compounds and source-specific markers to organic carbon ratios. In spite of transboundary pollution episodes, Hyytiala registered the lowest levels among all locations. CPI values close to 1 for the aliphatic fraction of the Montseny aerosol suggest that the anthropogenic input may be associated with the transport of aged air masses from the surrounding industrial/urban areas, which superimpose the locally originated hydrocarbons with biogenic origin. Aliphatic and aromatic hydrocarbons in samples from San Pietro Capofiume reveal that fossil fuel combustion is a major source influencing the diel pattern of concentrations. This source contributed to 25-45% of the ambient organic carbon (OC) at the Po Valley site. Aerosols from the German meadow presented variable contributions from both biogenic and anthropogenic sources. The highest levels of vegetation wax components and biogenic secondary organic aerosol (SOA) products were observed at K-puszta, while anthropogenic SOA compounds predominated in Barcelona. The primary vehicular emissions in the Spanish city accounted for around 25-30% of the OC in aerosols. Besides the traffic input (10% of OC), residential wood burning was found to be another dominant emission source contributing to the atmospheric aerosol (up to 38% of OC) at the Swiss urban location. It was estimated that around 10% of the OC mass in the urban sites originates from cooking emissions. Aerosols from the urban area of Zurich presented a much higher PAH content, and benzo(a)pyrene equivalent concentrations sometimes exceeding the mandatory limit. (C) 2012 Elsevier Ltd. All rights reserved.
|
|
| 37. |
- Anderson, Maria, 1983, et al.
(författare)
-
Characterization of particles from a marine engine operating at low loads
- 2015
-
Ingår i: Atmospheric Environment. - : Elsevier BV. - 1873-2844 .- 1352-2310. ; 101, s. 65-71
-
Tidskriftsartikel (refereegranskat)abstract
- Particle emissions from a marine diesel engine operating at low loads with four different fuels were characterized with respect to particle number (PN) and particle mass (PM), size distribution, volatility and chemical composition. The four different fuels used were Swedish Environmental class 1 (MK1) and class 3 diesel (MK3), heavy fuel oil (HFO, 0.12 wt% S) and marine diesel oil (MDO, 0.52 wt% S). The measurements were performed for a marine diesel engine in a test-bed engine lab and the particle emissions were measured with an Engine Exhaust Particle Sizer and a Dust Monitor, giving the number concentrations in the size range of 5.6-560 nm and 300 nm to 20 gm, respectively. To quantify the amount of solid particles a thermodenuder was used. Additionally, filter samples were taken for gravimetric, black carbon (BC) and elemental analysis. The particle emissions showed a bimodal size distribution by number and the number concentrations were dominated by nanoparticles (diameter (Dp) 50 nm generally were solid primary particles. Combustion of HFO resulted in the highest PN and PM concentrations. Emission factors (EFs) for PM and PN for both the total particle emissions and the fraction of primary, solid particles are presented for different fuels and loads. EFs for nitrogen oxides (NOx), BC and some elements (Ca, Fe, V, Ni, Zn) are presented as well. This study contributes to understanding particle emissions from potential future fuels as well as emissions in ports and coastal areas where lower engine loads are common.
|
|
| 38. |
- Andersson, August, et al.
(författare)
-
(14)C-Based source assessment of soot aerosols in Stockholm and the Swedish EMEP-Aspvreten regional background site
- 2011
-
Ingår i: Atmospheric Environment. - : Elsevier BV. - 1352-2310 .- 1873-2844. ; 45:1, s. 215-222
-
Tidskriftsartikel (refereegranskat)abstract
- Combustion-derived soot or black carbon (BC) in the atmosphere has a strong influence on both climate and human health. In order to propose effective mitigation strategies for BC emissions it is of importance to investigate geographical distributions and seasonal variations of BC emission sources. Here, a radiocarbon methodology is used to distinguish between fossil fuel and biomass burning sources of soot carbon (SC). SC is isolated for subsequent off-line (14)C quantification with the chemothermal oxidation method at 375 degrees C (CTO-375 method), which reflects a recalcitrant portion of the BC continuum known to minimize inadvertent inclusion of any non-pyrogenic organic matter. Monitored wind directions largely excluded impact from the Stockholm metropolitan region at the EMEP-Aspvreten rural station 70 km to the south-west. Nevertheless, the Stockholm city and the rural stations yielded similar relative source contributions with fraction biomass (f(biomass)) for fall and winter periods in the range of one-third to half. Large temporal variations in (14)C-based source apportionment was noted for both the 6 week fall and the 4 month winter observations. The f(biomass) appeared to be related to the SC concentration suggesting that periods of elevated BC levels may be caused by increased wood fuel combustion. These results for the largest metropolitan area in Scandinavia combine with other recent (14)C-based studies of combustion-derived aerosol fractions to suggest that biofuel combustion is contributing a large portion of the BC load to the northern European atmosphere.
|
|
| 39. |
- Andersson, Camilla, 1979-, et al.
(författare)
-
Population exposure and mortality due to regional background PM in Europe – longterm simulations of source-region and shipping contributions
- 2009
-
Ingår i: Atmospheric Environment. - : Elsevier BV. - 1352-2310 .- 1873-2844. ; 43:22-23, s. 3614-3620
-
Tidskriftsartikel (refereegranskat)abstract
- This paper presents the contribution to population exposure (PE) of regional background fine primary (PPM2.5) and secondary inorganic (SIA) particulate matter and its impact on mortality in Europe during 1997–2003 calculated with a chemistry transport model. Contributions to concentrations and PE due to emissions from shipping, Western (WEU), Eastern (EEU), and Northern Europe are compared. WEU contributes about 40% to both PPM2.5 and SIA concentrations, whereas the EEU contribution to PPM2.5 is much higher (43% of total PPM2.5) than to SIA (29% of total SIA). The population weighted average concentration (PWC) of PPM2.5 is a factor of 2.3 higher than average (non-weighted) concentrations, whereas for SIA the PWC is only a factor 1.6 higher. This is due to PPM2.5 concentrations having larger gradients and being relatively high over densely populated areas, whereas SIA is formed outside populated areas. WEU emissions contribute relatively more than EEU to PWC and mortality due to both PPM2.5 and SIA in Europe. The number of premature deaths in Europe is estimated to 301 000 per year due to PPM2.5 exposure and 245 000 due to SIA, despite 3.3 times higher average SIA concentrations. This is due to population weighting and assumed (and uncertain) higher relative risk of mortality for PPM2.5 components (2.8 times higher RR for PPM2.5). This study indicates that it might be more efficient, for the health of the European population, to decrease primary PM emissions (especially in WEU) than to decrease precursors of SIA, but more knowledge on the toxicity of different PM constituents is needed before firm conclusions can be drawn.
|
|
| 40. |
|
|
| 41. |
|
|
| 42. |
|
|
| 43. |
|
|
| 44. |
- Avagyan, Rozanna, et al.
(författare)
-
Particulate hydroxy-PAH emissions from a residential wood log stove using different fuels and burning conditions
- 2016
-
Ingår i: Atmospheric Environment. - : Elsevier BV. - 1352-2310 .- 1873-2844. ; 140, s. 1-9
-
Tidskriftsartikel (refereegranskat)abstract
- Hydroxylated polycyclic aromatic hydrocarbons are oxidation products of polycyclic aromatic hydrocarbons, but have not been studied as extensively as polycyclic aromatic hydrocarbons. Several studies have however shown that hydroxylated polycyclic aromatic hydrocarbons have toxic and carcinogenic properties. They have been detected in air samples in semi urban areas and combustion is assumed to be the primary source of those compounds. To better understand the formation and occurrence of particulate hydroxylated polycyclic aromatic hydrocarbons from residential wood log stove combustion, 9 hydroxylated polycyclic aromatic hydrocarbons and 2 hydroxy biphenyls were quantified in particles generated from four different types of wood logs (birch, spruce, pine, aspen) and two different combustion conditions (nominal and high burn rate). A previously developed method utilizing liquid chromatography photo ionization tandem mass spectrometry and pressurized liquid extraction was used. Polycyclic aromatic hydrocarbons were analyzed along with hydroxylated polycyclic aromatic hydrocarbons. The hydroxylated polycyclic aromatic hydrocarbon emissions varied significantly across different wood types and burning conditions; the highest emissions for nominal burn rate were from spruce and for high burn rate from pine burning. Emissions from nominal burn rate corresponded on average to 15% of the emissions from high burn rate, with average emissions of 218 mu g/MJ(fuel) and 32.5 mu g/MJ(fuel) for high burn rate and nominal burn rate, respectively. Emissions of the measured hydroxylated polycyclic aromatic hydrocarbons corresponded on average to 28% of polycyclic aromatic hydrocarbons emissions. This study shows that wood combustion is a large emission source of hydroxylated polycyclic aromatic hydrocarbons and that not only combustion conditions, but also wood type influences the emissions of hydroxylated polycyclic aromatic hydrocarbons and polycyclic aromatic hydrocarbons. There are few studies that have determined hydroxylated polycyclic aromatic hydrocarbons in emissions from wood combustion, and it is therefore necessary to further investigate the formation, occurrence and distribution of these compounds as they are present in significant amounts in wood smoke particles.
|
|
| 45. |
- Baduel, Christine, et al.
(författare)
-
Summer/winter variability of the surfactants in aerosols from Grenoble, France
- 2012
-
Ingår i: Atmospheric Environment. - : Elsevier BV. - 1352-2310 .- 1873-2844. ; 47, s. 413-420
-
Tidskriftsartikel (refereegranskat)abstract
- Many atmospheric aerosols seem to contain strong organic surfactants likely to enhance their cloud-forming properties. Yet, few techniques allow for the identification and characterization of these compounds. Recently, we introduced a double extraction method to isolate the surfactant fraction of atmospheric aerosol samples, and evidenced their very low surface tension (<= 30 mN m(-1)). In this work, this analytical procedure was further optimized. In addition to an optimized extraction and a reduction of the analytical time, the improved method led to a high reproducibility in the surface tension curves obtained (shapes and minimal values), illustrated by the low uncertainties on the values, +/- 10% or less. The improved method was applied to PM10 aerosols from the urban area of Grenoble, France collected from June 2009 to January 2010. Significant variability was observed between the samples. The minimum surface tension obtained from the summer samples was systematically lower (30 mN m(-1)) than that of the winter samples (35-45 mN m(-1)). Sharp transitions in the curves together with the very low surface tensions suggested that the dominating surfactants in the summer samples were biosurfactants, which would be consistent with the high biogenic activity in that season. One group of samples from the winter also displayed sharp transitions, which, together with the slightly higher surface tension, suggested the presence of weaker, possibly man-made, surfactants. A second group of curves from the winter did not display any clear transition but were similar to those of macromolecular surfactants such as polysaccharides or humic substances from wood burning. These surfactants are thus likely to originate from wood burning, the dominating source for aerosols in Grenoble in winter. These observations thus confirm the presence of surfactants from combustion processes in urban aerosols reported by other groups and illustrates the ability of our method to distinguish between different types of surfactants in atmospheric samples.
|
|
| 46. |
- Beelen, Rob, et al.
(författare)
-
Development of NO2 and NOx land use regression models for estimating air pollution exposure in 36 study areas in Europe : the ESCAPE project
- 2013
-
Ingår i: Atmospheric Environment. - : Elsevier. - 1352-2310 .- 1873-2844. ; 72, s. 10-23
-
Tidskriftsartikel (refereegranskat)abstract
- Estimating within-city variability in air pollution concentrations is important. Land use regression (LUR) models are able to explain such small-scale within-city variations. Transparency in LUR model development methods is important to facilitate comparison of methods between different studies. We therefore developed LUR models in a standardized way in 36 study areas in Europe for the ESCAPE (European Study of Cohorts for Air Pollution Effects) project.Nitrogen dioxide (NO2) and nitrogen oxides (NOx) were measured with Ogawa passive samplers at 40 or 80 sites in each of the 36 study areas. The spatial variation in each area was explained by LUR modeling. Centrally and locally available Geographic Information System (GIS) variables were used as potential predictors. A leave-one out cross-validation procedure was used to evaluate the model performance.There was substantial contrast in annual average NO2 and NOx concentrations within the study areas. The model explained variances (R2) of the LUR models ranged from 55% to 92% (median 82%) for NO2 and from 49% to 91% (median 78%) for NOx. For most areas the cross-validation R2 was less than 10% lower than the model R2. Small-scale traffic and population/household density were the most common predictors. The magnitude of the explained variance depended on the contrast in measured concentrations as well as availability of GIS predictors, especially traffic intensity data were important. In an additional evaluation, models in which local traffic intensity was not offered had 10% lower R2 compared to models in the same areas in which these variables were offered.Within the ESCAPE project it was possible to develop LUR models that explained a large fraction of the spatial variance in measured annual average NO2 and NOx concentrations. These LUR models are being used to estimate outdoor concentrations at the home addresses of participants in over 30 cohort studies.
|
|
| 47. |
- Beko, Gabriel, et al.
(författare)
-
Contribution of various microenvironments to the daily personal exposure to ultrafine particles: Personal monitoring coupled with GPS tracking
- 2015
-
Ingår i: Atmospheric Environment. - : Elsevier BV. - 1352-2310. ; 110, s. 122-129
-
Tidskriftsartikel (refereegranskat)abstract
- Exposure to ultrafine particles (UFP) may have adverse health effects. Central monitoring stations do not represent the personal exposure to UFP accurately. Few studies have previously focused on personal exposure to UFP. Sixty non-smoking residents living in Copenhagen, Denmark were asked to carry a backpack equipped with a portable monitor, continuously recording particle number concentrations (PN), in order to measure the real-time individual exposure over a period of similar to 48 h. A GPS logger was carried along with the particle monitor and allowed us to estimate the contribution of UFP exposure occurring in various microenvironments (residence, during active and passive transport, other indoor and outdoor environments) to the total daily exposure. On average, the fractional contribution of each microenvironment to the daily integrated personal exposure roughly corresponded to the fractions of the day the subjects spent in each microenvironment. The home environment accounted for 50% of the daily personal exposure. Indoor environments other than home or vehicles contributed with similar to 40%. The highest median UFP concentration was obtained during passive transport (vehicles). However, being in transit or outdoors contributed 5% or less to the daily exposure. Additionally, the subjects recorded in a diary the periods when they were at home. With this approach, 66% of the total daily exposure was attributable to the home environment. The subjects spent 28% more time at home according to the diary, compared to the GPS. These results may indicate limitations of using diaries, but also possible inaccuracy and miss-classification in the GPS data. (C) 2015 Elsevier Ltd. All rights reserved.
|
|
| 48. |
- Bengtsson, Göran, et al.
(författare)
-
Persistence of plasmid RP4 in Pseudomonas putida and loss of its expression of antibiotic resistance in a groundwater microcosm
- 2004
-
Ingår i: Atmospheric Environment. - : Elsevier BV. - 1352-2310. ; 36:6, s. 999-1008
-
Tidskriftsartikel (refereegranskat)abstract
- We examined the stability of plasmid RN and its expression of antibiotic-resistance genes in suspended and sorbed Pseudomonas putida in aquifer microcosms. Test tubes containing different proportions of sterilized aquifer soil and groundwater were inoculated with bacteria and incubated for up to 26 d. Serial dilutions were made to agar plates with or without antibiotics, to quantify the functional stability of the plasmid. The structural integrity of RN was examined by plasmid extraction, digestion with restriction enzymes, and agarose gel electrophoresis. The plasmid-borne resistance gene expression disappeared in 80-90% of the cells during day 1 of incubation in aquifer soil and then remained at that frequency throughout the experiment. The RP4 plasmid was present in cells without antibiotic-resistance gene expression, indicating that the observed loss of plasmid-encoded activity was most likely due to a reduction in expression of the resistance genes. The increased growth rate in groundwater amended with glucose and phosphate had no significant influence on plasmid loss or antibiotic-resistance expression, suggesting that plasmid loss and antibiotic-resistance expression were independent of the growth rate. Most of the reduction of resistance gene expression was associated with the presence of soil particles, and 70% of the resistance expression was retained in bacteria incubated for 1 d in groundwater alone. Bacteria sorbed to the soil particles had a lower frequency of expression of resistance genes than suspended bacteria, but the difference was not caused by sorbed inorganic or organic chemicals. Resistance gene expression was partly recovered in suspended bacteria after in vitro exposure to the antibiotics and after first isolating on agar without antibiotics and then replica plating to agar containing the antibiotics.
|
|
| 49. |
|
|
| 50. |
- Bennett, M, et al.
(författare)
-
Joint application of Doppler Lidar and differential absorption lidar to estimate the atomic mercury flux from a chlor-alkali plant
- 2006
-
Ingår i: Atmospheric Environment. - : Elsevier BV. - 1352-2310. ; 40:4, s. 664-673
-
Tidskriftsartikel (refereegranskat)abstract
- We have combined differential absorption lidar (DIAL) measurements of mercury concentrations downwind of a chloralkali plant (Rosignano Solvay) with measurements of wind profiles made with a Doppler Lidar based on modern fibreoptic technology. Since the flux of pollutant is equal to the cross-wind integral of the product of concentration and wind speed, this should permit us to make a more precise estimate of the fugitive emission of mercury from the plant than could be obtained by using anemometer measurements of the wind. The flux was estimated to be 54g Hgh(-1) using an anemometer on the plant building; 49g Hgh(-1) using an anemometer on a nearby 10m mast; and 48g Hgh(-1) using wind speed corrections estimated from the Doppler Lidar measurements. Because of difficulties with the range resolution of the Doppler Lidar, the precision of this estimate was not as good as it should have been, though the difference from the rooftop anemometer remains statistically significant. Corrections of this magnitude are irrelevant to the Rosignano plant, where the emission rate varies strongly with the meteorological conditions. Where a precise estimate of a steady flux is required, however, reliable measurements of the wind profile in the wake of the source are essential. Doppler Lidar provides a possible method for acquiring such measurements. (c) 2005 Elsevier Ltd. All rights reserved.
|
|
