SwePub
Sök i SwePub databas

  Utökad sökning

Träfflista för sökning "L773:1748 0221 "

Sökning: L773:1748 0221

  • Resultat 1-50 av 342
Sortera/gruppera träfflistan
   
NumreringReferensOmslagsbildHitta
1.
  • Blanco, A., et al. (författare)
  • Performance of timing resistive plate chambers with relativistic neutrons from 300 to 1500 MeV
  • 2015
  • Ingår i: Journal of Instrumentation. - : IOP Publishing. - 1748-0221. ; 10:2
  • Tidskriftsartikel (refereegranskat)abstract
    • A prototype composed of four resistive plate chamber layers has been exposed to quasi-monoenergetic neutrons produced from a deuteron beam of varying energy (300 to 1500 AMeV) in experiment S406 at GSI, Darmstad, Germany. Each layer, with an active area of about 2000 × 500 mm2, is made of modules containing the active gaps, all in multigap construction. Each gap is defined by 0.3 mm nylon mono-filaments positioned between 2.85 mm thick float glass electrodes. The modules are operated in avalanche mode with a non-flammable gas mixture composed of 90% C2H2F4 and 10% SF6. The signals are readout by a pick-up electrode formed by 15 copper strips (per layer), spaced at a pitch of 30 mm, connected at both sides to timing front end electronics. Measurements of the time of flight jitter of neutrons, in the mentioned energy range, point to a contribution of the resistive plate chamber in the order of 150 ps, independent of the neutron energy.
  •  
2.
  • Milstead, David A., et al. (författare)
  • Modelling radiation damage to pixel sensors in the ATLAS detector
  • 2019
  • Ingår i: Journal of Instrumentation. - : IOP PUBLISHING LTD. - 1748-0221. ; 14:6
  • Tidskriftsartikel (refereegranskat)abstract
    • Silicon pixel detectors are at the core of the current and planned upgrade of the ATLAS experiment at the LHC. Given their close proximity to the interaction point, these detectors will be exposed to an unprecedented amount of radiation over their lifetime. The current pixel detector will receive damage from non-ionizing radiation in excess of 1015 1 MeV neq/cm2, while the pixel detector designed for the high-luminosity LHC must cope with an order of magnitude larger fluence. This paper presents a digitization model incorporating effects of radiation damage to the pixel sensors. The model is described in detail and predictions for the charge collection efficiency and Lorentz angle are compared with collision data collected between 2015 and 2017 (≤ 10 1 MeV neq/cm2). © 2019 CERN for the benefit of the ATLAS collaboration. Published by IOP Publishing Ltd on behalf of Sissa Medialab. Original content from this work may be used under the terms of the Creative Commons Attribution 3.0 licence.
  •  
3.
  • Backman, Filip, 1991-, et al. (författare)
  • The development of the NNBAR experiment
  • 2022
  • Ingår i: Journal of Instrumentation. - : Institute of Physics (IOP). - 1748-0221. ; 17:10
  • Tidskriftsartikel (refereegranskat)abstract
    • The NNBAR experiment for the European Spallation Source will search for free neutrons converting to antineutrons with a sensitivity improvement of three orders of magnitude compared to the last such search. This paper describes progress towards a conceptual design report for NNBAR. The design of a moderator, neutron reflector, beamline, shielding and annihilation detector is reported. The simulations used form part of a model which will be used for optimisation of the experiment design and quantification of its sensitivity.
  •  
4.
  • An, S., et al. (författare)
  • Characterization of micro pore optics for full-field X-ray fluorescence imaging
  • 2023
  • Ingår i: Journal of Instrumentation. - 1748-0221. ; 18:1
  • Tidskriftsartikel (refereegranskat)abstract
    • Elemental mapping images can be achieved through step scanning imaging using pinhole optics or micro pore optics (MPO), or alternatively by full-field X-ray fluorescence imaging (FF-XRF). X-ray optics for FF-XRF can be manufactured with different micro-channel geometries such as square, hexagonal or circular channels. Each optic geometry creates different imaging artefacts. Square-channel MPOs generate a high intensity central spot due to two reflections via orthogonal channel walls inside a single channel, which is the desirable part for image formation, and two perpendicular lines forming a cross due to reflections in one plane only. Thus, we have studied the performance of a square-channel MPO in an FF-XRF imaging system. The setup consists of a commercially available MPO provided by Photonis and a Timepix3 readout chip with a silicon detector. Imaging of fluorescence from small metal particles has been used to obtain the point spread function (PSF) characteristics. The transmission through MPO channels and variation of the critical reflection angle are characterized by measurements of fluorescence from copper and titanium metal fragments. Since the critical angle of reflection is energy dependent, the cross-arm artefacts will affect the resolution differently for different fluorescence energies. It is possible to identify metal fragments due to the form of the PSF function. The PSF function can be further characterized using a Fourier transform to suppress diffuse background signals in the image.
  •  
5.
  • Aad, G, et al. (författare)
  • Performance of the ATLAS RPC detector and Level-1 muon barrel trigger at √s = 13 TeV
  • 2021
  • Ingår i: Journal of Instrumentation. - : Institute of Physics Publishing (IOPP). - 1748-0221. ; 16:7
  • Tidskriftsartikel (refereegranskat)abstract
    • The ATLAS experiment at the Large Hadron Collider (LHC) employs a trigger system consisting of a first-level hardware trigger (L1) and a software-based high-level trigger. The L1 muon trigger system selects muon candidates, assigns them to the correct LHC bunch crossing and classifies them into one of six transverse-momentum threshold classes. The L1 muon trigger system uses resistive-plate chambers (RPCs) to generate the muon-induced trigger signals in the central (barrel) region of the ATLAS detector. The ATLAS RPCs are arranged in six concentric layers and operate in a toroidal magnetic field with a bending power of 1.5 to 5.5 Tm. The RPC detector consists of about 3700 gas volumes with a total surface area of more than 4000 m2. This paper reports on the performance of the RPC detector and L1 muon barrel trigger using 60.8 fb-1 of proton-proton collision data recorded by the ATLAS experiment in 2018 at a centre-of-mass energy of 13 TeV. Detector and trigger performance are studied using Z boson decays into a muon pair. Measurements of the RPC detector response, efficiency, and time resolution are reported. Measurements of the L1 muon barrel trigger efficiencies and rates are presented, along with measurements of the properties of the selected sample of muon candidates. Measurements of the RPC currents, counting rates and mean avalanche charge are performed using zero-bias collisions. Finally, RPC detector response and efficiency are studied at different high voltage and front-end discriminator threshold settings in order to extrapolate detector response to the higher luminosity expected for the High Luminosity LHC. © 2021 CERN for the benefit of the ATLAS collaboration. Published by IOP Publishing Ltd on behalf of Sissa Medialab. Original content from this work may be used under the terms of the Creative Commons Attribution 4.0 licence
  •  
6.
  • Aad, G, et al. (författare)
  • ATLAS data quality operations and performance for 2015-2018 data-taking
  • 2020
  • Ingår i: Journal of Instrumentation. - : Institute of Physics Publishing (IOPP). - 1748-0221. ; 15:4
  • Tidskriftsartikel (refereegranskat)abstract
    • The ATLAS detector at the Large Hadron Collider reads out particle collision data from over 100 million electronic channels at a rate of approximately 100 kHz, with a recording rate for physics events of approximately 1 kHz. Before being certified for physics analysis at computer centres worldwide, the data must be scrutinised to ensure they are clean from any hardware or software related issues that may compromise their integrity. Prompt identification of these issues permits fast action to investigate, correct and potentially prevent future such problems that could render the data unusable. This is achieved through the monitoring of detector-level quantities and reconstructed collision event characteristics at key stages of the data processing chain. This paper presents the monitoring and assessment procedures in place at ATLAS during 2015-2018 data-taking. Through the continuous improvement of operational procedures, ATLAS achieved a high data quality efficiency, with 95.6% of the recorded proton-proton collision data collected at s=13 TeV certified for physics analysis.
  •  
7.
  • Aad, G, et al. (författare)
  • Performance of the upgraded PreProcessor of the ATLAS Level-1 Calorimeter Trigger
  • 2020
  • Ingår i: Journal of Instrumentation. - : IOP Publishing. - 1748-0221. ; 15:11
  • Tidskriftsartikel (refereegranskat)abstract
    • The PreProcessor of the ATLAS Level-1 Calorimeter Trigger prepares the analogue trigger signals sent from the ATLAS calorimeters by digitising, synchronising, and calibrating them to reconstruct transverse energy deposits, which are then used in further processing to identify event features. During the first long shutdown of the LHC from 2013 to 2014, the central components of the PreProcessor, the Multichip Modules, were replaced by upgraded versions that feature modern ADC and FPGA technology to ensure optimal performance in the high pile-up environment of LHC Run 2. This paper describes the features of the new Multichip Modules along with the improvements to the signal processing achieved. c 2020 CERN for the benefit of the ATLAS collaboration. Published by IOP Publishing Ltd on behalf of Sissa Medialab.
  •  
8.
  • Aad, G, et al. (författare)
  • Resolution of the ATLAS muon spectrometer monitored drift tubes in LHC Run 2
  • 2019
  • Ingår i: Journal of Instrumentation. - : IOP PUBLISHING LTD. - 1748-0221. ; 14:9
  • Tidskriftsartikel (refereegranskat)abstract
    • The momentum measurement capability of the ATLAS muon spectrometer relies fundamentally on the intrinsic single-hit spatial resolution of the monitored drift tube precision tracking chambers. Optimal resolution is achieved with a dedicated calibration program that addresses the specific operating conditions of the 354 000 high-pressure drift tubes in the spectrometer. The calibrations consist of a set of timing offsets and drift time to drift distance transfer relations, and result in chamber resolution functions. This paper describes novel algorithms to obtain precision calibrations from data collected by ATLAS in LHC Run 2 and from a gas monitoring chamber, deployed in a dedicated gas facility. The algorithm output consists of a pair of correction constants per chamber which are applied to baseline calibrations, and determined to be valid for the entire ATLAS Run 2. The final single-hit spatial resolution, averaged over 1172 monitored drift tube chambers, is 81.7 ± 2.2 μm. © 2019 CERN for the benefit of the ATLAS collaboration. Published by IOP Publishing Ltd on behalf of Sissa Medialab. Original content from this work may be used under the terms of the Creative Commons Attribution 3.0 licence. Any further distribution of this work must maintain attribution to the author(s) and the title of the work, journal citation and DOI.
  •  
9.
  • Andrean, Stefio Y., et al. (författare)
  • Measurements of sensor radiation damage in the ATLAS inner detector using leakage currents
  • 2021
  • Ingår i: Journal of Instrumentation. - : IOP Publishing Ltd. - 1748-0221. ; 16:8
  • Tidskriftsartikel (refereegranskat)abstract
    • Non-ionizing energy loss causes bulk damage to the silicon sensors of the ATLAS pixel and strip detectors. This damage has important implications for data-taking operations, charged-particle track reconstruction, detector simulations, and physics analysis. This paper presents simulations and measurements of the leakage current in the ATLAS pixel detector and semiconductor tracker as a function of location in the detector and time, using data collected in Run 1 (2010–2012) and Run 2 (2015–2018) of the Large Hadron Collider. The extracted fluence shows a much stronger |z|-dependence in the innermost layers than is seen in simulation. Furthermore, the overall fluence on the second innermost layer is significantly higher than in simulation, with better agreement in layers at higher radii. These measurements are important for validating the simulation models and can be used in part to justify safety factors for future detector designs and interventions.
  •  
10.
  • G., Aad, et al. (författare)
  • Electron and photon performance measurements with the ATLAS detector using the 2015-2017 LHC proton-proton collision data
  • 2019
  • Ingår i: Journal of Instrumentation. - : IOP PUBLISHING LTD. - 1748-0221. ; 14:12
  • Tidskriftsartikel (refereegranskat)abstract
    • This paper describes the reconstruction of electrons and photons with the ATLAS detector, employed for measurements and searches exploiting the complete LHC Run 2 dataset. An improved energy clustering algorithm is introduced, and its implications for the measurement and identification of prompt electrons and photons are discussed in detail. Corrections and calibrations that affect performance, including energy calibration, identification and isolation efficiencies, and the measurement of the charge of reconstructed electron candidates are determined using up to 81 fb-1 of proton-proton collision data collected at √s = 13 TeV between 2015 and 2017. © 2019 CERN for the benefit of the ATLAS collaboration. Published by IOP Publishing Ltd on behalf of Sissa Medialab.
  •  
11.
  • G., Aad, et al. (författare)
  • Performance of the ATLAS muon triggers in Run 2
  • 2020
  • Ingår i: Journal of Instrumentation. - : IOP Publishing. - 1748-0221. ; 15:9
  • Tidskriftsartikel (refereegranskat)abstract
    • The performance of the ATLAS muon trigger system is evaluated with proton-proton (pp) and heavy-ion (HI) collision data collected in Run 2 during 2015-2018 at the Large Hadron Collider. It is primarily evaluated using events containing a pair of muons from the decay of Z bosons to cover the intermediate momentum range between 26 GeV and 100 GeV. Overall, the efficiency of the single-muon triggers is about 68% in the barrel region and 85% in the endcap region. The pT range for efficiency determination is extended by using muons from decays of Jψ mesons, W bosons, and top quarks. The performance in HI collision data is measured and shows good agreement with the results obtained in pp collisions. The muon trigger shows uniform and stable performance in good agreement with the prediction of a detailed simulation. Dedicated multi-muon triggers with kinematic selections provide the backbone to beauty, quarkonia, and low-mass physics studies. The design, evolution and performance of these triggers are discussed in detail. © 2020 CERN for the benefit of the ATLAS collaboration..
  •  
12.
  • Milstead, David A., et al. (författare)
  • Comparison between simulated and observed LHC beam backgrounds in the ATLAS experiment at Ebeam=4 TeV
  • 2018
  • Ingår i: Journal of Instrumentation. - : Institute of Physics Publishing (IOPP). - 1748-0221. ; 13:12
  • Tidskriftsartikel (refereegranskat)abstract
    • Results of dedicated Monte Carlo simulations of beam-induced background (BIB) in the ATLAS experiment at the Large Hadron Collider (LHC) are presented and compared with data recorded in 2012. During normal physics operation this background arises mainly from scattering of the 4 TeV protons on residual gas in the beam pipe. Methods of reconstructing the BIB signals in the ATLAS detector, developed and implemented in the simulation chain based on the \textsc{Fluka} Monte Carlo simulation package, are described. The interaction rates are determined from the residual gas pressure distribution in the LHC ring in order to set an absolute scale on the predicted rates of BIB so that they can be compared quantitatively with data. Through these comparisons the origins of the BIB leading to different observables in the ATLAS detectors are analysed. The level of agreement between simulation results and BIB measurements by ATLAS in 2012 demonstrates that a good understanding of the origin of BIB has been reached. © 2018 CERN for the benefit of the ATLAS collaboration.
  •  
13.
  • Milstead, David A., et al. (författare)
  • Electron and photon energy calibration with the ATLAS detector using 2015-2016 LHC proton-proton collision data
  • 2019
  • Ingår i: Journal of Instrumentation. - : Institute of Physics (IOP). - 1748-0221. ; 14:3
  • Tidskriftsartikel (refereegranskat)abstract
    • This paper presents the electron and photon energy calibration obtained with the ATLAS detector using about 36 fb -1 of LHC proton-proton collision data recorded at s=13 TeV in 2015 and 2016. The different calibration steps applied to the data and the optimization of the reconstruction of electron and photon energies are discussed. The absolute energy scale is set using a large sample of Z boson decays into electron-positron pairs. The systematic uncertainty in the energy scale calibration varies between 0.03% to 0.2% in most of the detector acceptance for electrons with transverse momentum close to 45 GeV . For electrons with transverse momentum of 10 GeV the typical uncertainty is 0.3% to 0.8% and it varies between 0.25% and 1% for photons with transverse momentum around 60 GeV . Validations of the energy calibration with J/ψ → e + e - decays and radiative Z boson decays are also presented. © 2019 CERN for the benefit of the ATLAS collaboration.
  •  
14.
  • Mullier, G.A., et al. (författare)
  • Operation and performance of the ATLAS semiconductor tracker in LHC Run 2
  • 2022
  • Ingår i: Journal of Instrumentation. - : IOP Publishing Ltd. - 1748-0221. ; 17:1
  • Tidskriftsartikel (refereegranskat)abstract
    • The semiconductor tracker (SCT) is one of the tracking systems for charged particles in the ATLAS detector. It consists of 4088 silicon strip sensor modules. During Run 2 (2015-2018) the Large Hadron Collider delivered an integrated luminosity of 156 fb−1 to the ATLAS experiment at a centre-of-mass proton-proton collision energy of 13 TeV. The instantaneous luminosity and pile-up conditions were far in excess of those assumed in the original design of the SCT detector. Due to improvements to the data acquisition system, the SCT operated stably throughout Run 2. It was available for 99.9% of the integrated luminosity and achieved a data-quality efficiency of 99.85%. Detailed studies have been made of the leakage current in SCT modules and the evolution of the full depletion voltage, which are used to study the impact of radiation damage to the modules. © 2022 CERNüäβ
  •  
15.
  • Abulaiti, Yiming, et al. (författare)
  • A measurement of material in the ATLAS tracker using secondary hadronic interactions in 7 TeV p p collisions
  • 2016
  • Ingår i: Journal of Instrumentation. - : IOP PUBLISHING LTD. - 1748-0221. ; 11
  • Tidskriftsartikel (refereegranskat)abstract
    • Knowledge of the material in the ATLAS inner tracking detector is crucial in under-standing the reconstruction of charged-particle tracks, the performance of algorithms that identify jets containing b-hadrons and is also essential to reduce background in searches for exotic particles that can decay within the inner detector volume. Interactions of primary hadrons produced in pp collisions with the material in the inner detector are used to map the location and amount of this material. The hadronic interactions of primary particles may result in secondary vertices, which in this analysis are reconstructed by an inclusive vertex-finding algorithm. Data were collected using minimum-bias triggers by the ATLAS detector operating at the LHC during 2010 at centre-of-mass energy root s = 7 TeV, and correspond to an integrated luminosity of 19 nb(-1). Kinematic properties of these secondary vertices are used to study the validity of the modelling of hadronic interactions in simulation. Secondary-vertex yields are compared between data and simulation over a volume of about 0.7m(3) around the interaction point, and agreement is found within overall uncertainties.
  •  
16.
  • Milstead, David A., et al. (författare)
  • Performance of the ATLAS Transition Radiation Tracker in Run 1 of the LHC: Tracker properties
  • 2017
  • Ingår i: Journal of Instrumentation. - : Institute of Physics (IOP). - 1748-0221. ; 12:5
  • Tidskriftsartikel (refereegranskat)abstract
    • The tracking performance parameters of the ATLAS Transition Radiation Tracker (TRT) as part of the ATLAS inner detector are described in this paper for different data-taking conditions in proton-proton, proton-lead and lead-lead collisions at the Large Hadron Collider (LHC). The performance is studied using data collected during the first period of LHC operation (Run 1) and is compared with Monte Carlo simulations. The performance of the TRT, operating with two different gas mixtures (xenon-based and argon-based) and its dependence on the TRT occupancy is presented. These studies show that the tracking performance of the TRT is similar for the two gas mixtures and that a significant contribution to the particle momentum resolution is made by the TRT up to high particle densities. © CERN 2017 for the benefit of the ATLAS collaboration.
  •  
17.
  •  
18.
  • Aad, G, et al. (författare)
  • Beam-induced and cosmic-ray backgrounds observed in the ATLAS detector during the LHC 2012 proton-proton running period
  • 2016
  • Ingår i: Journal of Instrumentation. - : IOP PUBLISHING LTD. - 1748-0221. ; 11:5
  • Tidskriftsartikel (refereegranskat)abstract
    • This paper discusses various observations on beam-induced and cosmic-ray backgrounds in the ATLAS detector during the LHC 2012 proton-proton run. Building on published results based on 2011 data, the correlations between background and residual pressure of the beam vacuum are revisited. Ghost charge evolution over 2012 and its role for backgrounds are evaluated. New methods to monitor ghost charge with beam-gas rates are presented and observations of LHC abort gap population by ghost charge are discussed in detail. Fake jets from colliding bunches and from ghost charge are analysed with improved methods, showing that ghost charge in individual radio-frequency buckets of the LHC can be resolved. Some results of two short periods of dedicated cosmic-ray background data-taking are shown; in particular cosmic-ray muon induced fake jet rates are compared to Monte Carlo simulations and to the fake jet rates from beam background. A thorough analysis of a particular LHC fill, where abnormally high background was observed, is presented. Correlations between backgrounds and beam intensity losses in special fills with very high β∗ are studied. © 2016 CERN for the benefit of the ATLAS collaboration.
  •  
19.
  •  
20.
  • Becker, J., et al. (författare)
  • High speed cameras for X-rays : AGIPD and others
  • 2013
  • Ingår i: Journal of Instrumentation. - 1748-0221. ; 8:1, s. Art. no. C01042-
  • Tidskriftsartikel (refereegranskat)abstract
    • Experiments at high pulse rate Free Electron Laser (FEL) facilities require new cameras capable of acquiring 2D images at high rates, handling large signal dynamic ranges and resolving images from individual pulses. The Adaptive Gain Integrated Pixel Detector (AGIPD) will operated with pulse rates and separations of 27000/s and 220 ns, respectively at European XFEL. Si-sensors, ASICs, PCBs, and FPGA logic are developed for a 1 Mega-pixel camera with 200 μm square pixels with per-pulse occupancies 104. Data from 3520 images/s will be transferred with 80 Gbits/s to a DAQ-system. The electronics have been adapted for use in other synchrotron light source detectors. 
  •  
21.
  • Esebamen, Omeime, et al. (författare)
  • Surface State Effects on N+P Doped Electron Detector
  • 2011
  • Ingår i: Journal of Instrumentation. - 1748-0221. ; 6:12, s. Art. no. C12019-
  • Tidskriftsartikel (refereegranskat)abstract
    • Surface states and interface recombination velocity that exist between detector interfaces have always been known to affect the performance of a detector. This article describes how the detector performance varies when the doping profile is altered. When irradiated with electrons, the results show that while changes in the doping profile have an effect of the detector responsivity with respect to the interface recombination velocityVs, there is no visible effect with respect tofixed oxide chargeQfotherwise known as interface fixed charge density.
  •  
22.
  • Norlin, Börje, et al. (författare)
  • Readout cross-talk for alpha-particle measurements in a pixelated sensor system
  • 2015
  • Ingår i: Journal of Instrumentation. - : IOP. - 1748-0221. ; 10
  • Tidskriftsartikel (refereegranskat)abstract
    • Simulations in Medici are performed to quantify crosstalk and charge sharing in a hybrid pixelated silicon detector. Crosstalk and charge sharing degrades the spatial and spectral resolution of single photon processing X-ray imaging systems. For typical medical X-ray imaging applications, the process is dominated by charge sharing between the pixels in the sensor. For heavier particles each impact generates a large amount of charge and the simulation seems to over predict the charge collection efficiency. This indicates that some type of non modelled degradation of the charge transport efficiency exists, like the plasma effect where the plasma might shield the generated charges from the electric field and hence distorts the charge transport process. Based on the simulations it can be reasoned that saturation of the amplifiers in the Timepix system might generate crosstalk that increases the charge spread measured from ion impact on the sensor.
  •  
23.
  • Aad, G, et al. (författare)
  • Performance of b-jet identification in the ATLAS experiment
  • 2016
  • Ingår i: Journal of Instrumentation. - : Institute of Physics (IOP). - 1748-0221. ; 11:4
  • Tidskriftsartikel (refereegranskat)abstract
    • The identification of jets containing b hadrons is important for the physics programme of the ATLAS experiment at the Large Hadron Collider. Several algorithms to identify jets containing b hadrons are described, ranging from those based on the reconstruction of an inclusive secondary vertex or the presence of tracks with large impact parameters to combined tagging algorithms making use of multi-variate discriminants. An independent b-tagging algorithm based on the reconstruction of muons inside jets as well as the b-tagging algorithm used in the online trigger are also presented. The b-jet tagging efficiency, the c-jet tagging efficiency and the mistag rate for light flavour jets in data have been measured with a number of complementary methods. The calibration results are presented as scale factors defined as the ratio of the efficiency (or mistag rate) in data to that in simulation. In the case of b jets, where more than one calibration method exists, the results from the various analyses have been combined taking into account the statistical correlation as well as the correlation of the sources of systematic uncertainty. © CERN 2016 for the benefit of the ATLAS collaboration, published under the terms of the Creative Commons Attribution 3.0 License by IOP Publishing Ltd and Sissa Medialab srl.
  •  
24.
  • Milstead, David A., et al. (författare)
  • Study of the material of the ATLAS inner detector for Run 2 of the LHC
  • 2017
  • Ingår i: Journal of Instrumentation. - : Institute of Physics (IOP). - 1748-0221. ; 12:12
  • Tidskriftsartikel (refereegranskat)abstract
    • The ATLAS inner detector comprises three different sub-detectors: the pixel detector, the silicon strip tracker, and the transition-radiation drift-tube tracker. The Insertable B-Layer, a new innermost pixel layer, was installed during the shutdown period in 2014, together with modifications to the layout of the cables and support structures of the existing pixel detector. The material in the inner detector is studied with several methods, using a low-luminosity s=13 TeV pp collision sample corresponding to around 2.0 nb-1 collected in 2015 with the ATLAS experiment at the LHC. In this paper, the material within the innermost barrel region is studied using reconstructed hadronic interaction and photon conversion vertices. For the forward rapidity region, the material is probed by a measurement of the efficiency with which single tracks reconstructed from pixel detector hits alone can be extended with hits on the track in the strip layers. The results of these studies have been taken into account in an improved description of the material in the ATLAS inner detector simulation, resulting in a reduction in the uncertainties associated with the charged-particle reconstruction efficiency determined from simulation. © 2017 CERN.
  •  
25.
  • Aad, G, et al. (författare)
  • Electron and photon energy calibration with the ATLAS detector using LHC Run 2 data
  • 2024
  • Ingår i: Journal of Instrumentation. - : Institute of Physics. - 1748-0221. ; 19:2
  • Tidskriftsartikel (refereegranskat)abstract
    • This paper presents the electron and photon energy calibration obtained with the ATLAS detector using 140 fb−1 of LHC proton-proton collision data recorded at √s = 13 TeV between 2015 and 2018. Methods for the measurement of electron and photon energies are outlined, along with the current knowledge of the passive material in front of the ATLAS electromagnetic calorimeter. The energy calibration steps are discussed in detail, with emphasis on the improvements introduced in this paper. The absolute energy scale is set using a large sample of Z-boson decays into electron-positron pairs, and its residual dependence on the electron energy is used for the first time to further constrain systematic uncertainties. The achieved calibration uncertainties are typically 0.05% for electrons from resonant Z-boson decays, 0.4% at ET ∼ 10 GeV, and 0.3% at ET ∼ 1 TeV; for photons at ET ∼ 60 GeV, they are 0.2% on average. This is more than twice as precise as the previous calibration. The new energy calibration is validated using J/ → ee and radiative Z-boson decays. © 2024 Institute of Physics. All rights reserved.
  •  
26.
  •  
27.
  •  
28.
  •  
29.
  • Aad, G., et al. (författare)
  • The ATLAS Experiment at the CERN Large Hadron Collider
  • 2008
  • Ingår i: Journal of Instrumentation. - 1748-0221. ; 3:S08003
  • Forskningsöversikt (refereegranskat)abstract
    • The ATLAS detector as installed in its experimental cavern at point 1 at CERN is described in this paper. A brief overview of the expected performance of the detector when the Large Hadron Collider begins operation is also presented.
  •  
30.
  • Aaij, R., et al. (författare)
  • Curvature-bias corrections using a pseudomass method
  • 2024
  • Ingår i: Journal of Instrumentation. - 1748-0221. ; 19:3
  • Tidskriftsartikel (refereegranskat)abstract
    • Momentum measurements for very high momentum charged particles, such as muons from electroweak vector boson decays, are particularly susceptible to charge-dependent curvature biases that arise from misalignments of tracking detectors. Low momentum charged particles used in alignment procedures have limited sensitivity to coherent displacements of such detectors, and therefore are unable to fully constrain these misalignments to the precision necessary for studies of electroweak physics. Additional approaches are therefore required to understand and correct for these effects. In this paper the curvature biases present at the LHCb detector are studied using the pseudomass method in proton-proton collision data recorded at centre of mass energy √s = 13 TeV during 2016, 2017 and 2018. The biases are determined using Z → μ+μ- decays in intervals defined by the data-taking period, magnet polarity and muon direction. Correcting for these biases, which are typically at the 10-4 GeV-1 level, improves the Z → μ+μ- mass resolution by roughly 18% and eliminates several pathological trends in the kinematic-dependence of the mean dimuon invariant mass. © 2024 CERN.
  •  
31.
  • Aaij, R., et al. (författare)
  • Helium identification with LHCb
  • 2024
  • Ingår i: Journal of Instrumentation. - 1748-0221. ; 19:2
  • Tidskriftsartikel (refereegranskat)abstract
    • The identification of helium nuclei at LHCb is achieved using a method based on measurements of ionisation losses in the silicon sensors and timing measurements in the Outer Tracker drift tubes. The background from photon conversions is reduced using the RICH detectors and an isolation requirement. The method is developed using pp collision data at √s = 13 TeV recorded by the LHCb experiment in the years 2016 to 2018, corresponding to an integrated luminosity of 5.5 fb−1. A total of around 105 helium and antihelium candidates are identified with negligible background contamination. The helium identification efficiency is estimated to be approximately 50% with a corresponding background rejection rate of up to O(1012). These results demonstrate the feasibility of a rich programme of measurements of QCD and astrophysics interest involving light nuclei. © 2024 Institute of Physics. All rights reserved.
  •  
32.
  • Aaij, R., et al. (författare)
  • Momentum scale calibration of the LHCb spectrometer
  • 2024
  • Ingår i: Journal of Instrumentation. - 1748-0221. ; 19:2
  • Tidskriftsartikel (refereegranskat)abstract
    • For accurate determination of particle masses accurate knowledge of the momentum scale of the detectors is crucial. The procedure used to calibrate the momentum scale of the LHCb spectrometer is described and illustrated using the performance obtained with an integrated luminosity of 1.6 fb−1 collected during 2016 in pp running. The procedure uses large samples of J/ → +− and B+ → J/K+ decays and leads to a relative accuracy of 3 × 10−4 on the momentum scale. © 2024 Institute of Physics. All rights reserved.
  •  
33.
  • Aamodt, K., et al. (författare)
  • Alignment of the ALICE Inner Tracking System with cosmic-ray tracks
  • 2010
  • Ingår i: Journal of Instrumentation. - 1748-0221. ; 5
  • Konferensbidrag (refereegranskat)abstract
    • ALICE (A Large Ion Collider Experiment) is the LHC (Large Hadron Collider) experiment devoted to investigating the strongly interacting matter created in nucleus-nucleus collisions at the LHC energies. The ALICE ITS, Inner Tracking System, consists of six cylindrical layers of silicon detectors with three different technologies; in the outward direction: two layers of pixel detectors, two layers each of drift, and strip detectors. The number of parameters to be determined in the spatial alignment of the 2198 sensor modules of the ITS is about 13,000. The target alignment precision is well below 10 mu m in some cases (pixels). The sources of alignment information include survey measurements, and the reconstructed tracks from cosmic rays and from proton-proton collisions. The main track-based alignment method uses the Millepede global approach. An iterative local method was developed and used as well. We present the results obtained for the ITS alignment using about 10(5) charged tracks from cosmic rays that have been collected during summer 2008, with the ALICE solenoidal magnet switched off.
  •  
34.
  • Aamodt, K., et al. (författare)
  • The ALICE experiment at the CERN LHC
  • 2008
  • Ingår i: Journal of Instrumentation. - 1748-0221. ; 3:S08002
  • Forskningsöversikt (refereegranskat)abstract
    • ALICE (A Large Ion Collider Experiment) is a general-purpose, heavy-ion detector at the CERN LHC which focuses on QCD, the strong-interaction sector of the Standard Model. It is designed to address the physics of strongly interacting matter and the quark-gluon plasma at extreme values of energy density and temperature in nucleus-nucleus collisions. Besides running with Pb ions, the physics programme includes collisions with lighter ions, lower energy running and dedicated proton-nucleus runs. ALICE will also take data with proton beams at the top LHC energy to collect reference data for the heavy-ion programme and to address several QCD topics for which ALICE is complementary to the other LHC detectors. The ALICE detector has been built by a collaboration including currently over 1000 physicists and engineers from 105 Institutes in 30 countries, Its overall dimensions are 16 x 16 x 26 m(3) with a total weight of approximately 10 000 t. The experiment consists of 18 different detector systems each with its own specific technology choice and design constraints, driven both by the physics requirements and the experimental conditions expected at LHC. The most stringent design constraint is to cope with the extreme particle multiplicity anticipated in central Pb-Pb collisions. The different subsystems were optimized to provide high-momentum resolution as well as excellent Particle Identification (PID) over a broad range in momentum, up to the highest multiplicities predicted for LHC. This will allow for comprehensive studies of hadrons, electrons, muons, and photons produced in the collision of heavy nuclei. Most detector systems are scheduled to be installed and ready for data taking by mid-2008 when the LHC is scheduled to start operation, with the exception of parts of the Photon Spectrometer (PHOS), Transition Radiation Detector (TRD) and Electro Magnetic Calorimeter (EMCal). These detectors will be completed for the high-luminosity ion run expected in 2010. This paper describes in detail the detector components as installed for the first data taking in the summer of 2008.
  •  
35.
  • Abat, E., et al. (författare)
  • A layer correlation technique for pion energy calibration at the 2004 ATLAS Combined Beam Test
  • 2011
  • Ingår i: Journal of Instrumentation. - : Institute of Physics (IOP). - 1748-0221. ; 6
  • Tidskriftsartikel (refereegranskat)abstract
    • A new method for calibrating the hadron response of a segmented calorimeter is developed and successfully applied to beam test data. It is based on a principal component analysis of energy deposits in the calorimeter layers, exploiting longitudinal shower development information to improve the measured energy resolution. Corrections for invisible hadronic energy and energy lost in dead material in front of and between the calorimeters of the ATLAS experiment were calculated with simulated Geant4 Monte Carlo events and used to reconstruct the energy of pions impinging on the calorimeters during the 2004 Barrel Combined Beam Test at the CERN H8 area. For pion beams with energies between 20 GeV and 180 GeV, the particle energy is reconstructed within 3% and the energy resolution is improved by between 11% and 25% compared to the resolution at the electromagnetic scale.
  •  
36.
  • Abat, E., et al. (författare)
  • Combined performance studies for electrons at the 2004 ATLAS combined test-beam
  • 2010
  • Ingår i: Journal of Instrumentation. - : Institute of Physics (IOP). - 1748-0221. ; 5, s. P11006-
  • Tidskriftsartikel (refereegranskat)abstract
    • In 2004 at the ATLAS (A Toroidal LHC ApparatuS) combined test beam, one slice of the ATLAS barrel detector (including an Inner Detector set-up and the Liquid Argon calorimeter) was exposed to particles from the H8 SPS beam line at CERN. It was the first occasion to test the combined electron performance of ATLAS. This paper presents results obtained for the momentum measurement p with the Inner Detector and for the performance of the electron measurement with the LAr calorimeter (energy E linearity and resolution) in the presence of a magnetic field in the Inner Detector for momenta ranging from 20 GeV/c to 100 GeV/c. Furthermore the particle identification capabilities of the Transition Radiation Tracker, Bremsstrahlungs-recovery algorithms relying on the LAr calorimeter and results obtained for the E/p ratio and a way how to extract scale parameters will be discussed.
  •  
37.
  • Abat, E., et al. (författare)
  • Photon reconstruction in the ATLAS Inner Detector and Liquid Argon Barrel Calorimeter at the 2004 Combined Test Beam
  • 2011
  • Ingår i: Journal of Instrumentation. - 1748-0221. ; 6
  • Tidskriftsartikel (refereegranskat)abstract
    • The reconstruction of photons in the ATLAS detector is studied with data taken during the 2004 Combined Test Beam, where a full slice of the ATLAS detector was exposed to beams of particles of known energy at the CERN SPS. The results presented show significant differences in the longitudinal development of the electromagnetic shower between converted and unconverted photons as well as in the total measured energy. The potential to use the reconstructed converted photons as a means to precisely map the material of the tracker in front of the electromagnetic calorimeter is also considered. All results obtained are compared with a detailed Monte-Carlo simulation of the test-beam setup which is based on the same simulation and reconstruction tools as those used for the ATLAS detector itself.
  •  
38.
  • Abat, E., et al. (författare)
  • The ATLAS Transition Radiation Tracker (TRT) proportional drift tube: design and performance
  • 2008
  • Ingår i: Journal of Instrumentation. - 1748-0221. ; 3:2
  • Tidskriftsartikel (refereegranskat)abstract
    • A straw proportional counter is the basic element of the ATLAS Transition Radiation Tracker (TRT). Its detailed properties as well as the main properties of a few TRT operating gas mixtures are described. Particular attention is paid to straw tube performance in high radiation conditions and to its operational stability.
  •  
39.
  • Abat, E., et al. (författare)
  • The ATLAS TRT barrel detector
  • 2008
  • Ingår i: Journal of Instrumentation. - 1748-0221. ; 3
  • Tidskriftsartikel (refereegranskat)abstract
    • The ATLAS TRT barrel is a tracking drift chamber using 52,544 individual tubular drift tubes. It is one part of the ATLAS Inner Detector, which consists of three sub-systems: the pixel detector spanning the radius range 4 to 20 cm, the semiconductor tracker (SCT) from 30 to 52 cm, and the transition radiation tracker ( TRT) from 56 to 108 cm. The TRT barrel covers the central pseudo-rapidity region |eta| < 1, while the TRT endcaps cover the forward and backward eta regions. These TRT systems provide a combination of continuous tracking with many measurements in individual drift tubes ( or straws) and of electron identification based on transition radiation from fibers or foils interleaved between the straws themselves. This paper describes the recently-completed construction of the TRT Barrel detector, including the quality control procedures used in the fabrication of the detector.
  •  
40.
  • Abat, E., et al. (författare)
  • The ATLAS TRT electronics
  • 2008
  • Ingår i: Journal of Instrumentation. - 1748-0221. ; 3:6
  • Tidskriftsartikel (refereegranskat)abstract
    • The ATLAS inner detector consists of three sub-systems: the pixel detector spanning the radius range 4cm-20cm, the semiconductor tracker at radii from 30 to 52 cm, and the transition radiation tracker (TRT), tracking from 56 to 107 cm. The TRT provides a combination of continuous tracking with many projective measurements based on individual drift tubes (or straws) and of electron identification based on transition radiation from fibres or foils interleaved between the straws themselves. This paper describes the on and off detector electronics for the TRT as well as the TRT portion of the data acquisition (DAQ) system.
  •  
41.
  • Abat, E., et al. (författare)
  • The ATLAS TRT end-cap detectors
  • 2008
  • Ingår i: Journal of Instrumentation. - 1748-0221. ; 3
  • Tidskriftsartikel (refereegranskat)abstract
    • The ATLAS TRT end-cap is a tracking drift chamber using 245,760 individual tubular drift tubes. It is a part of the TRT tracker which consist of the barrel and two end-caps. The TRT end-caps cover the forward and backward pseudo-rapidity region 1.0 < vertical bar eta vertical bar < 2.0, while the TRT barrel central eta region vertical bar eta vertical bar < 1.0. The TRT system provides a combination of continuous tracking with many measurements in individual drift tubes ( or straws) and of electron identification based on transition radiation from fibers or foils interleaved between the straws themselves. Along with other two sub-systems, namely the Pixel detector and Semi Conductor Tracker (SCT), the TRT constitutes the ATLAS Inner Detector. This paper describes the recently completed and installed TRT end-cap detectors, their design, assembly, integration and the acceptance tests applied during the construction.
  •  
42.
  • Abate, E., et al. (författare)
  • Combined performance tests before installation of the ATLAS Semiconductor and Transition Radiation Tracking Detectors
  • 2008
  • Ingår i: Journal of Instrumentation. - 1748-0221. ; 3
  • Tidskriftsartikel (refereegranskat)abstract
    • The ATLAS (A Toroidal LHC ApparatuS) Inner Detector provides charged particle tracking in the centre of the ATLAS experiment at the Large Hadron Collider (LHC). The Inner Detector consists of three subdetectors: the Pixel Detector, the Semiconductor Tracker (SCT), and the Transition Radiation Tracker (TRT). This paper summarizes the tests that were carried out at the final stage of SCT+TRT integration prior to their installation in ATLAS. The combined operation and performance of the SCT and TRT barrel and endcap detectors was investigated through a series of noise tests, and by recording the tracks of cosmic rays. This was a crucial test of hardware and software of the combined tracker detector systems. The results of noise and cross-talk tests on the SCT and TRT in their final assembled configuration, using final readout and supply hardware and software, are reported. The reconstruction and analysis of the recorded cosmic tracks allowed testing of the offline analysis chain and verification of basic tracker performance parameters, such as efficiency and spatial resolution, in combined operation before installation.
  •  
43.
  • Abbas, E., et al. (författare)
  • Performance of the ALICE VZERO system
  • 2013
  • Ingår i: Journal of Instrumentation. - 1748-0221. ; 8
  • Tidskriftsartikel (refereegranskat)abstract
    • ALICE is an LHC experiment devoted to the study of strongly interacting matter in proton-proton, proton-nucleus and nucleus-nucleus collisions at ultra-relativistic energies. The ALICE VZERO system, made of two scintillator arrays at asymmetric positions, one on each side of the interaction point, plays a central role in ALICE. In addition to its core function as a trigger source, the VZERO system is used to monitor LHC beam conditions, to reject beam-induced backgrounds and to measure basic physics quantities such as luminosity, particle multiplicity, centrality and event plane direction in nucleus-nucleus collisions. After describing the VZERO system, this publication presents its performance over more than four years of operation at the LHC.
  •  
44.
  • Abdel, N. S., et al. (författare)
  • Efficient ultra-thin transmission silicon detectors for a single-ion irradiation system at the Lund Ion Beam Analysis Facility
  • 2014
  • Ingår i: Journal of Instrumentation. - 1748-0221. ; 9
  • Tidskriftsartikel (refereegranskat)abstract
    • This paper describes the fabrication of efficient ultra-thin silicon transmission detectors for use as pre-cell detectors in single-ion experiments on living cells at the Lund Ion Beam Analysis Facility. More than 40 detectors of different thicknesses down to 5 mu m have been fabricated and packaged. The main design considerations were very low leakage current (below 9 nA) and low full depletion voltage at biases less than 0.5 V at room temperature. In addition, we have shown that cooling the device can reduce the leakage current to 3 nA. The experimental testing of the pre-cell detection system is based on counting the passage of ions through the transmission (Delta E) detector before hitting the stopping (E) detector placed behind it, to ensure the accurate delivery of specific doses of radiation to the sample. Optimal detection of the fabricated detectors for the passage of an external beam of 2.2 MeV protons was obtained by cooling the device to below 2 degrees C. Cooling the Delta E detectors provides up to 20% better energy resolution and up to 98% detection efficiency for 2.2 MeV protons. The development of this kind of efficient pre-cell detector enables a range of new experiments to be conducted on thick biological samples.
  •  
45.
  • Abelev, B., et al. (författare)
  • Measurement of visible cross sections in proton-lead collisions at root s(NN)=5.02 TeV in van der Meer scans with the ALICE detector
  • 2014
  • Ingår i: Journal of Instrumentation. - 1748-0221. ; 9
  • Tidskriftsartikel (refereegranskat)abstract
    • In 2013, the Large Hadron Collider provided proton-lead and lead-proton collisions at the center-of-mass energy per nucleon pair root s(NN) = 5.02 TeV. Van der Meer scans were performed for both configurations of colliding beams, and the cross section was measured for two reference processes, based on particle detection by the T0 and V0 detectors, with pseudo-rapidity coverage 4.6 < eta < 4.9, -3.3 < eta < -3.0 and 2.8 < eta < 5.1, -3.7 < eta < -1.7, respectively. Given the asymmetric detector acceptance, the cross section was measured separately for the two configurations. The measured visible cross sections are used to calculate the integrated luminosity of the proton-lead and lead-proton data samples, and to indirectly measure the cross section for a third, configuration-independent, reference process, based on neutron detection by the Zero Degree Calorimeters.
  •  
46.
  • Acharya, S., et al. (författare)
  • ALICE luminosity determination for Pb-Pb collisions at √ s NN= 5.02 TeV
  • 2024
  • Ingår i: Journal of Instrumentation. - 1748-0221. ; 19:2
  • Tidskriftsartikel (refereegranskat)abstract
    • Luminosity determination within the ALICE experiment is based on the measurement, in van der Meer scans, of the cross sections for visible processes involving one or more detectors (visible cross sections). In 2015 and 2018, the Large Hadron Collider provided Pb-Pb collisions at a centre-of-mass energy per nucleon pair of √s NN= 5.02 TeV. Two visible cross sections, associated with particle detection in the Zero Degree Calorimeter (ZDC) and in the V0 detector, were measured in a van der Meer scan. This article describes the experimental set-up and the analysis procedure, and presents the measurement results. The analysis involves a comprehensive study of beam-related effects and an improved fitting procedure, compared to previous ALICE studies, for the extraction of the visible cross section. The resulting uncertainty of both the ZDC-based and the V0-based luminosity measurement for the full sample is 2.5%. The inelastic cross section for hadronic interactions in Pb-Pb collisions at √s NN= 5.02 TeV, obtained by efficiency correction of the V0-based visible cross section, was measured to be 7.67 ± 0.25 b, in agreement with predictions using the Glauber model. © 2024 Institute of Physics. All rights reserved.
  •  
47.
  • Acharya, S, et al. (författare)
  • Calibration of the photon spectrometer PHOS of the ALICE experiment
  • 2019
  • Ingår i: Journal of Instrumentation. - 1748-0221. ; 14:May 2019
  • Tidskriftsartikel (refereegranskat)abstract
    • The procedure for the energy calibration of the high granularity electromagnetic calorimeter PHOS of the ALICE experiment is presented. The methods used to perform the relative gain calibration, to evaluate the geometrical alignment and the corresponding correction of the absolute energy scale, to obtain the nonlinearity correction coefficients and finally, to calculate the time-dependent calibration corrections, are discussed and illustrated by the PHOS performance in proton-proton (pp) collisions at s=13 TeV. After applying all corrections, the achieved mass resolutions for π0 and η mesons for pT > 1.7 GeV/c are σm π0 = 4.56 ± 0.03 MeV/c2 and σm η = 15.3 ± 1.0 MeV/c2, respectively.
  •  
48.
  • Acharya, S., et al. (författare)
  • Data-driven precision determination of the material budget in ALICE
  • 2023
  • Ingår i: Journal of Instrumentation. - 1748-0221. ; 18:11
  • Tidskriftsartikel (refereegranskat)abstract
    • The knowledge of the material budget with a high precision is fundamental for measurements of direct photon production using the photon conversion method due to its direct impact on the total systematic uncertainty. Moreover, it influences many aspects of the charged-particle reconstruction performance. In this article, two procedures to determine data-driven corrections to the material-budget description in ALICE simulation software are developed. One is based on the precise knowledge of the gas composition in the Time Projection Chamber. The other is based on the robustness of the ratio between the produced number of photons and charged particles, to a large extent due to the approximate isospin symmetry in the number of produced neutral and charged pions. Both methods are applied to ALICE data allowing for a reduction of the overall material budget systematic uncertainty from 4.5% down to 2.5%. Using these methods, a locally correct material budget is also achieved. The two proposed methods are generic and can be applied to any experiment in a similar fashion. © 2023 CERN for the benefit of the Alice collaboration.
  •  
49.
  • Acharya, S., et al. (författare)
  • Performance of the ALICE Electromagnetic Calorimeter
  • 2023
  • Ingår i: Journal of Instrumentation. - 1748-0221. ; 18:8
  • Tidskriftsartikel (refereegranskat)abstract
    • The performance of the electromagnetic calorimeter of the ALICE experiment during operation in 2010-2018 at the Large Hadron Collider is presented. After a short introduction into the design, readout, and trigger capabilities of the detector, the procedures for data taking, reconstruction, and validation are explained. The methods used for the calibration and various derived corrections are presented in detail. Subsequently, the capabilities of the calorimeter to reconstruct and measure photons, light mesons, electrons and jets are discussed. The performance of the calorimeter is illustrated mainly with data obtained with test beams at the Proton Synchrotron and Super Proton Synchrotron or in proton-proton collisions at s = 13 TeV, and compared to simulations.
  •  
50.
  • Adolfsson, J., et al. (författare)
  • SAMPA Chip : The New 32 Channels ASIC for the ALICE TPC and MCH Upgrades
  • 2017
  • Ingår i: Journal of Instrumentation. - 1748-0221. ; 12:4
  • Tidskriftsartikel (refereegranskat)abstract
    • This paper presents the test results of the second prototype of SAMPA, the ASIC designed for the upgrade of read-out front end electronics of the ALICE Time Projection Chamber (TPC) and Muon Chamber (MCH). SAMPA is made in a 130 nm CMOS technology with 1.25 V nominal voltage supply and provides 32 channels, with selectable input polarity, and three possible combinations of shaping time and sensitivity. Each channel consists of a Charge Sensitive Amplifier, a semi-Gaussian shaper and a 10-bit ADC; a Digital Signal Processor provides digital filtering and compression capability. In the second prototype run both full chip and single test blocks were fabricated, allowing block characterization and full system behaviour studies. Experimental results are here presented showing agreement with requirements for both the blocks and the full chip.
  •  
Skapa referenser, mejla, bekava och länka
  • Resultat 1-50 av 342
Typ av publikation
tidskriftsartikel (338)
forskningsöversikt (3)
konferensbidrag (1)
Typ av innehåll
refereegranskat (338)
övrigt vetenskapligt/konstnärligt (4)
Författare/redaktör
Brenner, Richard (43)
Bohm, Christian (42)
Ekelöf, Tord (31)
Silverstein, Samuel ... (30)
Zwalinski, L. (29)
Strandberg, Jonas (27)
visa fler...
Ellert, Mattias (27)
Lund-Jensen, Bengt (26)
Moa, Torbjörn (25)
Aad, G (24)
Åkesson, Torsten (23)
Smirnova, Oxana (21)
Anghinolfi, F. (21)
Mjörnmark, Ulf (20)
Doglioni, Caterina (19)
Farthouat, P. (19)
Hedberg, Vincent (18)
Jarlskog, Göran (18)
Dam, M. (18)
Di Girolamo, B. (18)
Hakobyan, H. (18)
Catinaccio, A. (17)
Ferrere, D. (17)
Abdallah, J (16)
Ripellino, Giulia (16)
Bergeås Kuutmann, El ... (16)
Baker, O. K. (16)
Cetin, S. A. (16)
Dittus, F. (16)
Froidevaux, D. (16)
Hajduk, Z. (16)
Hance, M. (16)
Hansen, P. H. (16)
Koffas, T. (16)
Koperny, S. (16)
Lacasta, C. (16)
Lichard, P. (16)
Lucotte, A. (16)
Luehring, F. (16)
Maleev, V. P. (16)
Ogren, H. (16)
Olszowska, J. (16)
Peshekhonov, V. D. (16)
Phillips, P. W. (16)
Rembser, C. (16)
Romaniouk, A. (16)
Rousseau, D. (16)
Schegelsky, V. A. (16)
Tikhomirov, V. O. (16)
Wang, C. (16)
visa färre...
Lärosäte
Uppsala universitet (140)
Lunds universitet (88)
Stockholms universitet (83)
Mittuniversitetet (74)
Kungliga Tekniska Högskolan (69)
Linköpings universitet (16)
visa fler...
Högskolan i Gävle (10)
Chalmers tekniska högskola (9)
Karolinska Institutet (7)
Linnéuniversitetet (3)
RISE (3)
Umeå universitet (1)
Luleå tekniska universitet (1)
Karlstads universitet (1)
visa färre...
Språk
Engelska (342)
Forskningsämne (UKÄ/SCB)
Naturvetenskap (290)
Teknik (75)
Medicin och hälsovetenskap (4)

År

Kungliga biblioteket hanterar dina personuppgifter i enlighet med EU:s dataskyddsförordning (2018), GDPR. Läs mer om hur det funkar här.
Så här hanterar KB dina uppgifter vid användning av denna tjänst.

 
pil uppåt Stäng

Kopiera och spara länken för att återkomma till aktuell vy