| 1. |
- Abbas, Ghazanfar, et al.
(författare)
-
Electrochemical investigation of mixed metal oxide nanocomposite electrode for low temperature solid oxide fuel cell
- 2017
-
Ingår i: International Journal of Modern Physics B. - : WORLD SCIENTIFIC PUBL CO PTE LTD. - 0217-9792. ; 31:27
-
Tidskriftsartikel (refereegranskat)abstract
- Zinc-based nanostructured nickel (Ni) free metal oxide electrode material Zn-0.60/CU0.20Mn0.20 oxide (CMZO) was synthesized by solid state reaction and investigated for low temperature solid oxide fuel cell (LTSOFC) applications. The crystal structure and surface morphology of the synthesized electrode material were examined by XRD and SEM techniques respectively. The particle size of ZnO phase estimated by Scherer's equation was 31.50 nm. The maximum electrical conductivity was found to be 12.567 S/cm and 5.846 S/cm in hydrogen and air atmosphere, respectively at 600 degrees C. The activation energy of the CMZO material was also calculated from the DC conductivity data using Arrhenius plots and it was found to be 0.060 and 0.075 eV in hydrogen and air atmosphere, respectively. The CMZO electrode-based fuel cell was tested using carbonated samarium doped ceria composite (NSDC) electrolyte. The three layers 13 mm in diameter and 1 mm thickness of the symmetric fuel cell were fabricated by dry pressing. The maximum power density of 728.86 mW/cm(2) was measured at 550 degrees C.
|
|
| 2. |
- Abbas, Ghazanfar, et al.
(författare)
-
Electrochemical study of nanostructured electrode for low-temperature solid oxide fuel cell (LTSOFC)
- 2014
-
Ingår i: International Journal of Energy Research. - : Hindawi Limited. - 0363-907X .- 1099-114X. ; 38:4, s. 518-523
-
Tidskriftsartikel (refereegranskat)abstract
- Zn-based nanostructured Ba0.05Cu0.25Fe0.10Zn0.60O (BCFZ) oxide electrode material was synthesized by solid-state reaction for low-temperature solid oxide fuel cell. The cell was fabricated by sandwiching NK-CDC electrolyte between BCFZ electrodes by dry press technique, and its performance was assessed. The maximum power density of 741.87 mW-cm(-2) was achieved at 550 degrees C. The crystal structure and morphology were characterized by X-ray diffractometer (XRD) and SEM. The particle size was calculated to be 25 nm applying Scherer's formula from XRD data. Electronic conductivities were measured with the four-probe DC method under hydrogen and air atmosphere. AC Electrochemical Impedance Spectroscopy of the BCFZ oxide electrode was also measured in hydrogen atmosphere at 450 degrees C.
|
|
| 3. |
- Abbas, Ghazanfar, et al.
(författare)
-
Preparation and characterization of nanocomposite calcium doped ceria electrolyte with alkali carbonates (NK-CDC) for SOFC
- 2010
-
Ingår i: ASME 2010 8th International Conference on Fuel Cell Science, Engineering and Technology, FUELCELL 2010. - : ASME Press. - 9780791844052 ; , s. 427-432
-
Konferensbidrag (refereegranskat)abstract
- The entire world's challenge is to find out the renewable energy sources due to rapid depletion of fossil fuels because of their high consumption. Solid Oxide Fuel Cells (SOFCs) are believed to be the best alternative source which converts chemical energy into electricity without combustion. Nanostructured study is required to develop highly ionic conductive electrolyte for SOFCs. In this work, the calcium doped ceria (Ce0.8Ca0.2O 1.9) coated with 20% molar ratio of two alkali carbonates (CDC-M: MCO3, where M= Na and K) electrolyte was prepared by co-precipitation method in this study. Ni based electrode was used to fabricate the cell by dry pressing technique. The crystal structure and surface morphology was characterized by X-Ray Diffractometer (XRD), Scanning Electron Microscopy (SEM) and High Resolution Transmission Electron Microscopy (HRTEM). The particle size was calculated in the range of 10-20nm by Scherrer's formula and compared with SEM and TEM results. The ionic conductivity was measured by using AC Electrochemical Impedance Spectroscopy (EIS) method. The activation energy was also evaluated. The performance of the cell was measured 0.567W/cm2 at temperature 550°C with hydrogen as a fuel.
|
|
| 4. |
- Abbas, Ghazanfar, et al.
(författare)
-
Preparation and Characterization of Nanocomposite Calcium Doped Ceria Electrolyte With Alkali Carbonates (NK-CDC) for SOFC
- 2011
-
Ingår i: Journal of Fuel Cell Science and Technology. - : ASME International. - 1550-624X .- 1551-6989. ; 8:4, s. 041013-
-
Tidskriftsartikel (refereegranskat)abstract
- The entire world's challenge is to find out the renewable energy sources due to rapid depletion of fossil fuels because of their high consumption. Solid oxide fuel cells (SOFCs) are believed to be the best alternative source, which converts chemical energy into electricity without combustion. Nanostructure study is required to develop highly ionic conductive electrolytes for SOFCs. In this work, the calcium doped ceria (Ce0.8Ca0.2O1.9) coated with 20% molar ratio of two alkali carbonates (CDC-M: MCO3, where M = Na and K) electrolyte was prepared by coprecipitation method. Ni based electrode was used to fabricate the cell by dry pressing technique. The crystal structure and surface morphology were characterized by an X-ray diffractometer, scanning electron microscopy (SEM), and high resolution transmission electron microscopy (TEM). The particle size was calculated in the range 10-20 nm by Scherer's formula and compared with SEM and TEM results. The ionic conductivity was measured by using ac electrochemical impedance spectroscopy method. The activation energy was also evaluated. The performance of the cell was measured 0.567 W/cm(2) at temperature 550 degrees C with hydrogen as a fuel.
|
|
| 5. |
- Abbas, Ghazanfar, et al.
(författare)
-
Study of CuNiZnGdCe-Nanocomposite Anode for Low Temperature SOFC
- 2012
-
Ingår i: Nanoscience and Nanotechnology Letters. - : American Scientific Publishers. - 1941-4900 .- 1941-4919. ; 4:4, s. 389-393
-
Tidskriftsartikel (refereegranskat)abstract
- Composite electrodes of Cu0.16Ni0.27Zn0.37Ce0.16Gd0.04 (CNZGC) oxides have been successfully synthesized by solid state reaction method as anode material for low temperature solid oxide fuel cell (LTSOFC). These electrodes are characterized by XRD followed by sintering at various time periods and temperatures. Particle size of optimized composition was calculated 40-85 nm and sintered at 800 degrees C for 4 hours. Electrical conductivity of 4.14 S/cm was obtained at a temperature of 550 degrees C by the 4-prob DC method. The activation energy was calculated 4 x 10(-2) eV at 550 degrees C. Hydrogen was used as fuel and air as oxidant at anode and cathode sides respectively. I-V/I-P curves were obtained in the temperature range of 400-550 degrees C. The maximum power density was achieved for 570 mW/cm(2) at 550 degrees C.
|
|
| 6. |
- Abbas, Ghazanfar, et al.
(författare)
-
Synthesize and characterization of nanocomposite anodes for low temperature solid oxide fuel cell
- 2015
-
Ingår i: International journal of hydrogen energy. - : Elsevier BV. - 0360-3199 .- 1879-3487. ; 40:1, s. 891-897
-
Tidskriftsartikel (refereegranskat)abstract
- Solid oxide fuel cells have much capability to become an economical alternative energy conversion technology having appropriate materials that can be operated at comparatively low temperature in the range of 400-600 degrees C. The nano-scale engineering has been incorporated to improve the catalytic activity of anode materials for solid oxide fuel cells. Nanostructured Al0.10NixZn0.90-xO oxides were prepared by solid state reaction, which were then mixed with the prepared Gadolinium doped Ceria GDC electrolyte. The crystal structure and surface morphology were characterized by XRD and SEM. The particle size was evaluated by XRD data and found in the range of 20-50 nm, which was then ensured by SEM pictures. The pellets of 13 mm diameter were pressed by dry press technique and electrical conductivities (DC and AC) were determined by four probe techniques and the values have been found to be 10.84 and 4.88 S/cm, respectively at hydrogen atmosphere in the temperature range of 300-600 degrees C. The Electrochemical Impedance Spectroscopy (EIS) analysis exhibits the pure electronic behavior at hydrogen atmosphere. The maximum power density of ANZ-GDC composite anode based solid oxide fuel cell has been achieved 705 mW/cm(2) at 550 degrees C.
|
|
| 7. |
- Abbas, Muhammad Ghazanfar, et al.
(författare)
-
Chemical Composition, Larvicidal and Repellent Activities of Wild Plant Essential Oils against Aedes aegypti
- 2023
-
Ingår i: Biology. - : MDPI AG. - 2079-7737. ; 12:1
-
Tidskriftsartikel (refereegranskat)abstract
- Bio-degradable and eco-friendly essential oils (EOs) extracted from Mentha longifolia, Salsola imbricata, Erigeron bonariensis, E. canadensis, Ailanthus altissima, and Zanthoxylum armatum were investigated for their repellent and larvicidal potential against Aedes aegypti mosquitoes. The EOs of M. longifolia, S. imbricata, E. bonariensis, E. canadensis, A. altissima, and Z. armatum exhibited 99.0%, 96.8%, 40.2%, 41.7%, 29.1%, and 13.2% repellency against mosquitoes at a tested dose of 33.3 μg/cm2, respectively. In time span bioassays, the EOs of M. longifolia, S. imbricata, E. bonariensis, and E. canadensis showed more than 40% repellency for 60 min at a tested dose of 330 μg/cm2. Larvicidal bioassays revealed that larvae of Ae. aegypti were the most susceptible to M. longifolia (LC50, 39.3 mg/L), E. bonariensis (LC50, 26.0 mg/L), E. canadensis (LC50, 35.7 mg/L), and Z. armatum (LC50, 35.9 mg/L) EOs upon 48 h exposure. The most abundant constituents in the EOs of M. longifolia, S. imbricata, E. bonariensis, E. canadensis and A. altissima were piperitone oxide (45.5%), carvone (39.9%), matricaria ester (43.1%), (31.7%) and eugenol (24.4%), respectively. Our study demonstrates that EOs of M. longifolia, S. imbricata, E. bonariensis, and E. canadensis might be used to control Ae. aegypti mosquitoes without harming humans or the environment.
|
|
| 8. |
- Afroz, Laila, et al.
(författare)
-
Nanocomposite Catalyst (1 – x)NiO-xCuO/yGDC for Biogas Fueled Solid Oxide Fuel Cells
- 2023
-
Ingår i: ACS Applied Energy Materials. - : American Chemical Society (ACS). - 2574-0962. ; 6:21, s. 10918-10928
-
Tidskriftsartikel (refereegranskat)abstract
- The composites of Ni–Cu oxides with gadolinium doped ceria (GDC) are emerging as highly proficient anode catalysts, owing to their remarkable performance for solid oxide fuel cells operated with biogas. In this context, the nanocomposite catalysts (1 – x)NiO-xCuO/yGDC (x = 0.2–0.8; y = 1,1.3) are synthesized using a solid-state reaction route. The cubic and monoclinic structures are observed for NiO and CuO phases, respectively, while CeO2 showed cubic fluorite structure. The scanning electron microscopic images revealed a rise in the particle size with an increase in the copper and GDC concentration. The optical band gap values are calculated in the range 2.82–2.33 eV from UV–visible analysis. The Raman spectra confirmed the presence of vibration modes of CeO2 and NiO. The electrical conductivity of the nanocomposite anodes is increased as the concentration of copper and GDC increased and reached at 9.48 S cm–1 for 0.2NiO-0.8CuO/1.3GDC composition at 650 °C. The electrochemical performance of (1 – x)NiO-xCuO/yGDC (x = 0.2–0.8; y = 1,1.3)-based fuel cells is investigated with biogas fuel at 650 °C. Among all of the as-synthesized anodes, the fuel cell with composition 0.2NiO-0.8CuO/1.3GDC showed the best performance, such as an open circuit voltage of 0.84 V and peak power density of 72 mW cm–2. However, from these findings, it can be inferred that among all other compositions, the 0.2NiO-0.8CuO/1.3GDC anode is a superior combination for the high electrochemical performance of solid oxide fuel cells fueled with biogas.
|
|
| 9. |
- Ajmal Khan, Muhammad, et al.
(författare)
-
Comparative study of the nano-composite electrolytes based on samaria-doped ceria for low temperature solid oxide fuel cells (LT-SOFCs)
- 2013
-
Ingår i: International journal of hydrogen energy. - : Elsevier BV. - 0360-3199 .- 1879-3487. ; 38:36, s. 16524-16531
-
Tidskriftsartikel (refereegranskat)abstract
- Ceria-based electrolyte materials have great potential in low and intermediate temperature solid oxide fuel cell applications. In the present study, three types of ceria-based nanocomposite electrolytes (LNK-SDC, LN-SDC and NK-SDC) were synthesized. One-step co-precipitation method was adopted and different techniques were applied to characterize the obtained ceria-based nano-composite electrolyte materials. TGA, XRD and SEM were used to analyze the thermal effect, crystal structure and morphology of the materials. Cubic fluorite structures have been observed in all composite electrolytes. Furthermore, the crystallite sizes of the LN-SDC, NK-SDC, LNK-SDC were calculated by Scherrer formula and found to be in the range 20 nm, 21 nm and 19 nm, respectively. These values emphasize a good agreement with the SEM results. The ionic conductivities were measured using EIS (Electrochemical Impedance Spectroscopy) with two-probe method and the activation energies were also calculated using Arrhenius plot. The maximum power density was achieved 484 mW/cm(2) of LNK-SDC electrolyte at 570 degrees C using the LiCuZnNi oxide electrodes.
|
|
| 10. |
- Haris, Abdullah, et al.
(författare)
-
Prolonged Repellent Activity of Plant Essential Oils against Dengue Vector, Aedes aegypti
- 2023
-
Ingår i: Molecules. - : MDPI AG. - 1431-5157 .- 1420-3049. ; 28:3
-
Tidskriftsartikel (refereegranskat)abstract
- Repellents are effective personal protective means against outdoor biting mosquitoes. Repellent formulations composed of EOs are finding increased popularity among consumers. In this study, after an initial screening of 11 essential oils (EOs) at the concentration of 33 μg/cm2, five of the most repellent EOs, Perovskia atriplicifolia, Citrus reticulata (fruit peels), C. reticulata (leaves), Mentha longifolia, and Dysphania ambrosioides were further investigated for repellent activity against Aedes aegypti mosquitoes in time span bioassays. When tested at the concentrations of 33 μg/cm2, 165 μg/cm2 and 330 μg/cm2, the EO of P. atriplicifolia showed the longest repellent effect up to 75, 90 and 135 min, respectively, which was followed by C. reticulata (peels) for 60, 90 and 120 min, M. longifolia for 45, 60 and 90 min, and C. reticulata (leaves) for 30, 45 and 75 min. Notably, the EO of P. atriplicifolia tested at the dose of 330 μg/cm2 showed complete protection for 60 min which was similar to the commercial mosquito repellent DEET. Gas chromatographic-mass spectrometric analyses of the EOs revealed camphor (19.7%), limonene (92.7%), sabinene (24.9%), carvone (82.6%), and trans-ascaridole (38.8%) as the major constituents of P. atriplicifolia, C. reticulata (peels), C. reticulata (leaves), M. longifolia, and D. ambrosioides, respectively. The results of the present study could help develop plant-based commercial repellents to protect humans from dengue mosquitoes.
|
|
| 11. |
- Hussain, Fida, et al.
(författare)
-
A modeling approach for low-temperature SOFC-based micro-combined heat and power systems
- 2019
-
Ingår i: International Journal of Modern Physics B. - : WORLD SCIENTIFIC PUBL CO PTE LTD. - 0217-9792. ; 33:4
-
Tidskriftsartikel (refereegranskat)abstract
- The world's challenge is to determine a more efficient, economical and environmental-friendly energy source to compete and replace the ongoing conventional energy resources. Solid oxide fuel cells (SOFCs) provide a highly efficient system to use divergent energy resources and have proved to provide the cleanest energy, least energy use, and lowest emissions. A techno-economic study is required to investigate the model design for SOFC-based micro-combined heat and power (m-CHP) systems for applications in terms of educational and commercial buildings. This work models and explores the optimized application of hydrogen gas-fueled SOFC-based m-CHP systems in educational buildings. Two educational departments' loads are presented and model of SOFC-based m-CHP system against the different electric power demands is performed, in order to provide a techno-economic assessment of the technology. For successful development of the technology, results are related to system rightsizing, operating strategies, thermal to electric ratios, and match between end-use, with an aim towards classifying the overall feasibility and essential application requirements.
|
|
| 12. |
- Hussain, Fida, et al.
(författare)
-
Comparative electrochemical investigation of zinc based nano-composite anode materials for solid oxide fuel cell
- 2019
-
Ingår i: Ceramics International. - : Elsevier. - 0272-8842 .- 1873-3956. ; 45:1, s. 1077-1083
-
Tidskriftsartikel (refereegranskat)abstract
- The structural and electrochemical properties of zinc based nano-composites anode materials with a composition of X0.25Ti0.5Zn0.70 (where X = Cu, Mn, Ag) have been investigated in this present study. The proposed Xo.zsTiousZno.70 oxide materials have been synthesized through sol-gel method. The doping effect of Cu, Mn, and Ag on TiZn oxides were analyzed in terms of electronic conduction and power density in hydrogen atmosphere at comparatively low temperature in the range of 650 degrees C. The crystal structure and surface morphology were examined by X-ray diffraction (XRD) and scanning electron microscopy (SEM) analysis techniques. The XRD patterns of composites depict that the average crystalline sizes lie in the range of 20-100 nm. Four -probe DC conductivity technique was used to measure the conductivity of the materials and maximum electrical conductivity of Ag0.25Ti0.05Zn0.70 oxide was found to be 7.81 S/cm at 650 degrees C. The band gap and absorption spectra were determined by ultra-violet visible (UV-Vis) and Fourier Transform Infrared spectroscopy (FTIR) techniques respectively. The maximum power density was achieved to be 354 mW/cm(2) at 650 degrees C by Ag0.25Ti0.05Zn0.70 oxide anode with SDC (electrolyte) and BSCF (conventional cathode) materials.
|
|
| 13. |
- Imran, Syed Khalid, et al.
(författare)
-
Characterization and Development of Bio-Ethanol Solid Oxide Fuel Cell
- 2011
-
Ingår i: Journal of Fuel Cell Science and Technology. - : ASME International. - 1550-624X .- 1551-6989. ; 8:6, s. 061014-
-
Tidskriftsartikel (refereegranskat)abstract
- Bio-ethanol based fuel cell is an energy source with a promising future. The low temperature solid oxide fuel cell fed by direct bio-ethanol is receiving considerable attention as a clean and highly efficient for the production of both electricity and high grade waste heat. The comparison of fuel cell performance with different metal-oxide based electrodes was investigated. The power densities of 584 mW cm(-2) and 514 mW cm(-2) at 520 degrees C and 570 degrees C respectively were found. The effect of electrode catalyst function, ethanol concentration on the electrical performance was investigated at different temperature ranged in between 300 degrees C-600 degrees C. The effect of deposited carbon on the electrode was investigated by energy-dispersive X-ray spectroscopy and scanning electron microscope after testing the cell with bio-ethanol.
|
|
| 14. |
- Khan, M. Ajmal, et al.
(författare)
-
Effect of titania concentration on the grain boundary conductivity of calcium-doped ceria electrolyte
- 2014
-
Ingår i: Ceramics International. - : Elsevier BV. - 0272-8842 .- 1873-3956. ; 40:7, s. 9775-9781
-
Tidskriftsartikel (refereegranskat)abstract
- A solid-state technique was used to synthesize ceria-based (CDC-xT, in which x=0-1 mol%) solid electrolyte ceramics. The effects of doping the ceramic solid electrolyte (CDC) with titanium oxide were studied with regard to densification, crystal structure, morphology, electro-impedance spectroscopy and fuel cell performance. TiO2 doping afforded materials a 95% relative density at 940 degrees C, approximately 200 degrees C lower than the temperature required without titanium oxide. The addition of titanium oxide (TiO2) reduced the CDC sintering temperature and significantly improved the grain boundary conduction. The minimum grain boundary resistivity was obtained at 0.8 mol% TiO2. X-ray diffraction (XRD) results showed that the lattice parameters enhanced with increased titanium oxide concentrations up to 0.8 mol%, revealing the solubility limit for Caria's fluorite structure. The optimum doping level (0.8 mol%) is provided maximum conductivity. Conductivities were measured using EIS (Electrochemical Impedance Spectroscopy) with a two-probe method, and the activation energies were calculated using the Arrhenius plots. The maximum power density (660 mW/cm(2)) was achieved with CDC 0.8T electrolyte at 650 degrees C using LiCuZnNi oxide electrodes.
|
|
| 15. |
- Khan, M. Ajmal, et al.
(författare)
-
Synthesize and characterization of ceria based nano-composite materials for low temperature solid oxide fuel cell
- 2018
-
Ingår i: International journal of hydrogen energy. - : PERGAMON-ELSEVIER SCIENCE LTD. - 0360-3199 .- 1879-3487. ; 43:12, s. 6310-6317
-
Tidskriftsartikel (refereegranskat)abstract
- The present study is focused on ceria based mixed (ionic and electronic conductor) composite Al0.05Ni0.1Ti0.05Zn0.80-SDC (ATZN-SDC) oxide material was prepared by solid state reaction, which can be used as anode materials for solid oxide fuel cell. The effect of Ti and Al oxides were analyzed on the NiZn-SDC composite with respect to its conductivity and catalytic activity in hydrogen atmosphere. The average crystallite size of the composite was found to be 40-100 nm by XRD and SEM. The DC conductivity was determined by 4-probe technique. The electrochemical impedance spectrum (EIS) was also examined in hydrogen atmosphere within a temperature range of 350-550 degrees C. The maximum power density 370 mW/cm(2) was achieved at 650 degrees C.
|
|
| 16. |
- Parveen, Amna, et al.
(författare)
-
Chemical composition of essential oils from natural populations of Artemisia scoparia collected at different altitudes : antibacterial, mosquito repellent, and larvicidal effects
- 2024
-
Ingår i: Molecules. - 1431-5157 .- 1420-3049. ; 29:6, s. 1359-
-
Tidskriftsartikel (refereegranskat)abstract
- The current study aimed to evaluate the presence of chemical variations in essential oils (EOs) extracted from Artemisia scoparia growing at different altitudes and to reveal their antibacterial, mosquito larvicidal, and repellent activity. The gas chromatographic–mass spectrometric analysis of A. scoparia EOs revealed that the major compounds were capillene (9.6–31.8%), methyleugenol (0.2–26.6%), β-myrcene (1.9–21.4%), γ-terpinene (1.5–19.4%), trans-β-caryophyllene (0.8–12.4%), and eugenol (0.1–9.1%). The EO of A. scoparia collected from the city of Attock at low elevation was the most active against Staphylococcus aureus, Bacillus subtilis, Escherichia coli, and Pseudomonas aeruginosa bacteria (minimum inhibitory concentration of 156–1250 µg/mL) and showed the best mosquito larvicidal activity (LC50, 55.3 mg/L). The EOs of A. scoparia collected from the high-altitude areas of Abbottabad and Swat were the most repellent for females of Ae. aegypti and exhibited repellency for 120 min and 165 min, respectively. The results of the study reveal that different climatic conditions and altitudes have significant effects on the chemical compositions and the biological activity of essential oils extracted from the same species.
|
|
| 17. |
- Qin, Haiying, et al.
(författare)
-
Direct biofuel low-temperature solid oxide fuel cells
- 2011
-
Ingår i: ENERGY & ENVIRONMENTAL SCIENCE. - : Royal Society of Chemistry (RSC). - 1754-5692 .- 1754-5706. ; 4:4, s. 1273-1276
-
Tidskriftsartikel (refereegranskat)abstract
- A low-temperature solid oxide fuel cell system was developed to use bioethanol and glycerol as fuels directly. This system achieved a maximum power density of 215 mW cm(-2) by using glycerol at 580 degrees C and produced a great impact on sustainable energy and the environment.
|
|
| 18. |
- Rafique, Asia, et al.
(författare)
-
Multioxide phase-based nanocomposite electrolyte (M@SDC where M = Zn2+ / Ba2+/ La2+/Zr-2/Al3+) materials
- 2020
-
Ingår i: Ceramics International. - : ELSEVIER SCI LTD. - 0272-8842 .- 1873-3956. ; 46:52, s. 6882-6888
-
Tidskriftsartikel (refereegranskat)abstract
- This paper deals with the development of a highly dense and stable electrolyte on the base of nanoionics oxide interface theory. This gives a comparative study of two-phase nanocomposite electrolytes that are developed for low temperature solid oxide fuel cells (LT-SOFCs). These nanocomposites are synthesised with different oxides, which are coated on the doped ceria that showed high oxide ion mobility for LT-SOFCs. These novel two-phase nanocomposite oxide ionic conductors (MCe0.8Sm0.2O2-MO2, where M = Zn2+/Ba2+/La3+/Zr2+/Al3+) were synthesised by a co-precipitation method. The interface study between these two phases was analysed by electrochemical impedance spectroscopy (EIS), while ionic conductivities were measured with DC conductivity (four probe method). The nanocomposite electrolytes exhibited higher conductivities with the increase of concentration of coated oxides but decreased at a certain level. The structural or morphological properties of the nanocomposite electrolytes were examined by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The thermal stability was investigated using thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The maximum performance of 590 mW/cm(2) at 550 degrees C was obtained for the Zn@SDC based cell, and the rest of the coated samples Ba@SDC, La@SDC, Zr@SDC and Al@SDC based cells showed values of 550 mW/cm(2), 540 mW/cm(2), 450 mW/cm(2), 340 mW/cm(2), respectively, with hydrogen as a fuel. Therefore, the coated-SDC based nanocomposite materials are a good approach for lowering the operating temperature to achieve the challenges of the solid oxide fuel cells (SOFC). These two-phase nanocomposite electrolytes satisfy the all requirements which one electrolyte should have, like high ionic conduction, thermodynamic stability and negligible electronic conduction.
|
|
| 19. |
- Raza, Rizwan, et al.
(författare)
-
Electrochemical study of the composite electrolyte based on samaria-doped ceria and containing yttria as a second phase
- 2011
-
Ingår i: Solid State Ionics. - : Elsevier BV. - 0167-2738 .- 1872-7689. ; 188:1, s. 58-63
-
Tidskriftsartikel (refereegranskat)abstract
- The purpose of this study is to develop new oxide ionic conductors based on nanocomposite materials for an advanced fuel cell (NANOCOFC) approach. The novel two phase nanocomposite oxide ionic conductors, Ce0.8Sm0.2O2-delta (SDC)-Y2O3 were synthesized by a co-precipitation method. The structure and morphology of the prepared electrolyte were investigated by means of X-ray diffraction (XRD) and high resolution scanning electron microscopy (HRSEM). XRD results showed a two phase composite consisting of yttrium oxide and samaria doped ceria and SEM results exhibited a nanostructure form of the sample. The yttrium oxide was used on the SDC as a second phase. The interface between two constituent phases and the ionic conductivities were studied with electrochemical impedance spectroscopy (EIS). An electrochemical study showed high oxide ion mobility and conductivity of the Y2O3-SDC two phase nanocomposite electrolytes at a low temperature (300-600 degrees C). Maximum conductivity (about 1.0 S cm(-1)) was obtained for the optimized Y2O3-SDC composite electrolyte at 600 degrees C. It is found that the nanocomposite electrolytes show higher conductivities with the increased concentration of yttrium oxides but decreases after reaching a certain level. A high fuel cell performance, 0.75 W cm(-2), was achieved at 580 degrees C.
|
|
| 20. |
- Raza, Rizwan, et al.
(författare)
-
GDC-Y2O3 Oxide Based Two Phase Nanocomposite Electrolyte
- 2011
-
Ingår i: JOURNAL OF FUEL CELL SCIENCE AND TECHNOLOGY. - : ASME International. - 1550-624X .- 1551-6989. ; 8:4, s. 041012-
-
Tidskriftsartikel (refereegranskat)abstract
- Oxide based two phase composite electrolyte (Ce0.9Gd0.1O2-Y2O3) was synthesized by coprecipitation method. The nanocomposite electrolyte showed the significant performance of power density 785 mW cm(-2) and higher conductivities at relatively low temperature 550 degrees C. Ionic conductivities were measured with ac impedance spectroscopy and four-probe dc method. The structural and morphological properties of the prepared electrolyte were investigated by scanning electron microscope (SEM). The thermal stability was determined with differential scanning calorimetry. The particle size that was calculated with Scherrer formula, 15-20 nm, is in a good agreement with the SEM and X-ray diffraction results. The purpose of this study is to introduce the functional nanocomposite materials for advanced fuel cell technology to meet the challenges of solid oxide fuel cell.
|
|
| 21. |
- Raza, Rizwan, et al.
(författare)
-
GDC-Y2O3 Oxide Based Two Phase Nanocomposite Electrolytes
- 2010
-
Ingår i: PROCEEDINGS OF THE ASME 8TH INTERNATIONAL CONFERENCE ON FUEL CELL SCIENCE, ENGINEERING, AND TECHNOLOGY 2010, VOL 1. - NEW YORK : AMER SOC MECHANICAL ENGINEERS. - 9780791844045 ; , s. 365-370
-
Konferensbidrag (refereegranskat)abstract
- An oxide based two phase nanocomposite electrolyte (Ce0.9Gd0.1O2) was synthesized by a co-precipitation method and coated with Yttrium oxide (Y2O3). The nanocomposite electrolyte showed the significant performance of power density 750mW/cm(2) and higher conductivities at relatively low temperature 550 degrees C. Ionic conductivities were measured with electrochemical impedance spectroscopy (EIS) and DC (4 probe method). The structural and morphological properties of the prepared electrolyte were investigated by means of High Resolution Scanning Electron Microscopy (HRSEM). The thermal stability was determined with Differential Scanning Calorimetry (DSC). The particle size was calculated with Scherrer formula and compare with SEM results, 15-20 nm is in a good agreement with the SEM and X-ray diffraction (XRD) results. The purpose of the study to introduce the functional nanocomposite materials, for advanced fuel cell technology (NANOCOFC) to meet the challenges of solid oxide fuel cell (SOFC).
|
|
| 22. |
- Ullah, Muhammad Kaleem, et al.
(författare)
-
Tri-doped ceria (M0.2Ce0.8O2-δ, M= Sm0.1 Ca0.05 Gd0.05) electrolyte for hydrogen and ethanol-based fuel cells
- 2019
-
Ingår i: Journal of Alloys and Compounds. - : Elsevier BV. - 0925-8388. ; 773, s. 548-554
-
Tidskriftsartikel (refereegranskat)abstract
- In recent scientific research, an interest has been gained significantly by rare earth metals such as cerium (Ce), samarium (Sm) and gadolinium (Gd) due to their use in fuel cells as electrolyte and catalysts. When used in an electrolyte, these materials lower the fuel cell's operating temperature compared to a conventional electrolyte, for example, yittria-stabilized zirconia (YSZ) which operates at a high temperature (≥800 °C). In this paper, the tri-doped ceria, M0.2Ce0.8O2-δ(M = Sm0.1Ca0.05Gd0.05) electrolyte powders was synthesized using the co-precipitation method at 80 °C. These dopants were used for CeO2with a total molar ratio of 1 M. Dry-pressed powder technique was used to make fuel cell pellets from the powder and placed them in the furnace to sinter at 700 °C for 60 min. Electrical conductivity of such a pellet in air was 1.2 × 10−2S cm−1at 700 °C measured by the ProboStat-NorECs setup. The crystal structure was determined with the help of X-ray diffraction (XRD), which showed that all the dopants were successfully doped in CeO2. Raman spectroscopy and UV-VIS spectroscopy were also carried out to analyse the molecular vibrations and absorbance, respectively. The maximum open-circuit voltages (OCVs) for hydrogen and ethanol fuelled at 550 °C were observed to be 0.89 V and 0.71 V with power densities 314 mW cm−2and 52.8 mW cm−2, respectively.
|
|
| 23. |
- Zhu, Bin, et al.
(författare)
-
An Electrolyte-Free Fuel Cell Constructed from One Homogenous Layer with Mixed Conductivity
- 2011
-
Ingår i: Advanced Functional Materials. - : Wiley. - 1616-301X .- 1616-3028. ; 21:13, s. 2465-2469
-
Tidskriftsartikel (refereegranskat)abstract
- Rather than using three layers, including an electrolyte, a working fuel cell is created that employs only one homogenous layer with mixed conductivity. The layer is a composite made from a mixture of metal oxide, Li(0.15)Ni(0.45)Zn(0.4) oxide, and an ionic conductor; ion-doped ceria. The single-component layer has a total conductivity of 0.1-1 S cm(-1) and exhibits both ionic and semiconducting properties. This homogenous one-layer device has a power output of more than 600 mW cm(-2) at 550 degrees C operating with H(2) and air. Overall conversion is completed in a similar way to a traditional fuel cell, even though the device does not include the electrolyte layer critical for traditional fuel-cell technologies using the three-component anode-electrolyte-cathode structure.
|
|
