| 1. |
- Sarfraz, Amina, et al.
(författare)
-
Catalytic Effect of Silicon Carbide on the Composite Anode of Fuel Cells
- 2021
-
Ingår i: ACS Applied Energy Materials. - : AMER CHEMICAL SOC. - 2574-0962. ; 4:7, s. 6436-6444
-
Tidskriftsartikel (refereegranskat)abstract
- High efficiency, fuel flexibility, and sustainable energy conversion make fuel cells attractive compared to conventional energy systems. The direct ethanol fuel cells have attracted much attention because of the direct utilization of ethanol fuel. Anode materials are required to enhance the catalytic activity of the liquid fuel, which oxidize the fuel at lower operating temperature. Therefore, the catalytic effect using silicon carbide has been investigated in the LiNiO2-delta anode. The material has been characterized, and it is found that SiC shows a cubic structure and LiNiO2-delta exhibits a hexagonal structure, while the LiNiO2-delta-SiC composite exhibits a mixed cubic and hexagonal phase. Scanning electron microscopy depicts that the material is porous. The Fourier transform infrared spectroscopy analysis shows the presence of Si-O-Si, Si-C, C=O, and Si-OH bonding. The LiNiO2-delta-SiC composite (1:0.3) exhibited a maximum electrical conductivity of 1.34 S cm(-1) at 650 degrees C with an electrical band gap of 0.84 eV. The fabricated cell with the LiNiO2-delta-SiC anode exhibits a power density of 0.20 W cm(-2) at 650 degrees C with liquid ethanol fuel. The results show that there is a promising catalytic activity of SiC in the fuel cell anode.
|
|
| 2. |
- Irshad, Muneeb, et al.
(författare)
-
Evaluation of BaCo0.Fe-4(0).4Zr0.2-xNixO3-delta perovskite cathode using nickel as a sintering aid for IT-SOFC
- 2021
-
Ingår i: RSC Advances. - : Royal Society of Chemistry. - 2046-2069. ; 11:24, s. 14475-14483
-
Tidskriftsartikel (refereegranskat)abstract
- In this research work, BaCo0.Fe-4(0).4Zr0.2-xNixO3-delta (x = 0, 0.01, 0.02, 0.03, 0.04) perovskite cathode material for IT-SOFC is synthesized successfully using a combustion method and sintered at low temperature. The effects of nickel as a sintering aid on the properties of BaCo0.Fe-4(0).Zr-4(0).O-2(3-delta) are investigated through different characterization methods. The addition of nickel increased the densification and grain growth at a lower sintering temperature 1200 degrees C. XRD analysis confirms a single phase of BaCo0.Fe-4(0).Zr-4(0).O-2(3-delta), and an increase in crystalline size is observed. SEM micrographs show formation of dense microstructure with increased nickel concentration. TGA analysis revealed that BaCo0.Fe-4(0).4Zr0.2-xNix cathode materials are thermally stable within the SOFC temperature range, and negligible weight loss of 2.3% is observed. The bonds of hydroxyl groups and metal oxides are confirmed for all samples through FTIR analysis. The highest electrical properties are observed for BaCo0.Fe-4(0).4Zr0.2-xNix (x = 0.04) due to increased densification and electronic defects compared to other compositions. The maximum power density of 0.47 W cm(-2) is obtained for a cell having cathode material BaCo0.Fe-4(0).4Zr0.2-xNix (x = 0.02) owing to its permeable and well-connected structure compared to others.
|
|
| 3. |
- Ullah, Muhammad Kaleem, et al.
(författare)
-
Tri-doped ceria (M0.2Ce0.8O2-δ, M= Sm0.1 Ca0.05 Gd0.05) electrolyte for hydrogen and ethanol-based fuel cells
- 2019
-
Ingår i: Journal of Alloys and Compounds. - : Elsevier BV. - 0925-8388. ; 773, s. 548-554
-
Tidskriftsartikel (refereegranskat)abstract
- In recent scientific research, an interest has been gained significantly by rare earth metals such as cerium (Ce), samarium (Sm) and gadolinium (Gd) due to their use in fuel cells as electrolyte and catalysts. When used in an electrolyte, these materials lower the fuel cell's operating temperature compared to a conventional electrolyte, for example, yittria-stabilized zirconia (YSZ) which operates at a high temperature (≥800 °C). In this paper, the tri-doped ceria, M0.2Ce0.8O2-δ(M = Sm0.1Ca0.05Gd0.05) electrolyte powders was synthesized using the co-precipitation method at 80 °C. These dopants were used for CeO2with a total molar ratio of 1 M. Dry-pressed powder technique was used to make fuel cell pellets from the powder and placed them in the furnace to sinter at 700 °C for 60 min. Electrical conductivity of such a pellet in air was 1.2 × 10−2S cm−1at 700 °C measured by the ProboStat-NorECs setup. The crystal structure was determined with the help of X-ray diffraction (XRD), which showed that all the dopants were successfully doped in CeO2. Raman spectroscopy and UV-VIS spectroscopy were also carried out to analyse the molecular vibrations and absorbance, respectively. The maximum open-circuit voltages (OCVs) for hydrogen and ethanol fuelled at 550 °C were observed to be 0.89 V and 0.71 V with power densities 314 mW cm−2and 52.8 mW cm−2, respectively.
|
|
| 4. |
- Afroz, Laila, et al.
(författare)
-
Nanocomposite Catalyst (1 – x)NiO-xCuO/yGDC for Biogas Fueled Solid Oxide Fuel Cells
- 2023
-
Ingår i: ACS Applied Energy Materials. - : American Chemical Society (ACS). - 2574-0962. ; 6:21, s. 10918-10928
-
Tidskriftsartikel (refereegranskat)abstract
- The composites of Ni–Cu oxides with gadolinium doped ceria (GDC) are emerging as highly proficient anode catalysts, owing to their remarkable performance for solid oxide fuel cells operated with biogas. In this context, the nanocomposite catalysts (1 – x)NiO-xCuO/yGDC (x = 0.2–0.8; y = 1,1.3) are synthesized using a solid-state reaction route. The cubic and monoclinic structures are observed for NiO and CuO phases, respectively, while CeO2 showed cubic fluorite structure. The scanning electron microscopic images revealed a rise in the particle size with an increase in the copper and GDC concentration. The optical band gap values are calculated in the range 2.82–2.33 eV from UV–visible analysis. The Raman spectra confirmed the presence of vibration modes of CeO2 and NiO. The electrical conductivity of the nanocomposite anodes is increased as the concentration of copper and GDC increased and reached at 9.48 S cm–1 for 0.2NiO-0.8CuO/1.3GDC composition at 650 °C. The electrochemical performance of (1 – x)NiO-xCuO/yGDC (x = 0.2–0.8; y = 1,1.3)-based fuel cells is investigated with biogas fuel at 650 °C. Among all of the as-synthesized anodes, the fuel cell with composition 0.2NiO-0.8CuO/1.3GDC showed the best performance, such as an open circuit voltage of 0.84 V and peak power density of 72 mW cm–2. However, from these findings, it can be inferred that among all other compositions, the 0.2NiO-0.8CuO/1.3GDC anode is a superior combination for the high electrochemical performance of solid oxide fuel cells fueled with biogas.
|
|
| 5. |
- Ali Ahmad, Syed Ossama, et al.
(författare)
-
Application of two-dimensional materials in perovskite solar cells: recent progress, challenges, and prospective solutions
- 2021
-
Ingår i: Journal of Materials Chemistry C. - : ROYAL SOC CHEMISTRY. - 2050-7526 .- 2050-7534. ; 9:40, s. 14065-14092
-
Forskningsöversikt (refereegranskat)abstract
- Perovskite solar cells (per-SCs) with high performance and cost-effective solution processing have been the center of interest for researchers in the past decade. Power conversion efficiencies (PCEs) have been gradually improved up to 25.2% with relatively improved stability, which is an unparalleled progress in all generations of solar cell (SC) technology. However, there are still some prevailing challenges regarding the stability and upscaling of these promising devices. Recently, 2D layered materials (LMs) have been extensively explored to overcome the prevailing challenges of poor stability (under moisture, light soaking and high temperature), halide segregation, hysteresis, involvement of toxic materials (i.e., lead), and upscaling of devices. A critical review addressing the recent developments in the use of 2D materials, especially transition metal dichalcogenides (TMDCs), is hence necessary. The development of novel synthesis and deposition techniques including liquid-metal synthesis and ultrasonic assisted spray pyrolysis has offered more efficient fabrication of 2D-LMs with controlled thickness and morphology. Effective functionalization approaches to increase the dispersability of 2D-LMs in non-polar solvents has boosted their potential application in solar cell technology as well. Moreover, compositing 2D TMDCs with suitable organic/inorganic compounds has enabled superior charge kinetics in all functional parts of per-SCs. In addition, newly developed materials such as graphyne and graphdyine along with 2D metal organic frameworks (MOFs) and covalent organic frameworks (COFs) have been employed in per-SCs to achieve PCEs up to 20%. This review summarizes the recent progress and challenges in the application of 2D-LMs in per-SCs and outlines the future pathways to further extend the PCE of per-SCs beyond 25%. This review particularly focuses on 2D-LMs as electrode materials and additives, the underlying charge (electron-hole) transport phenomenon in the functional layers, and their chemical and structural stability.
|
|
| 6. |
- Asim, Muhammad, et al.
(författare)
-
Techno-economic assessment of energy and environmental impact of waste-to-energy electricity generation
- 2023
-
Ingår i: Energy Reports. - : Elsevier. - 2352-4847. ; 9:Suppl 1, s. 1087-1097
-
Tidskriftsartikel (refereegranskat)abstract
- This study explored cumulative 127.5MW waste to energy (WtE) potential in five populous cities of Pakistan based on local waste characterization profiles and global standards. The 50MW WtE plant in Lahore using National electricity regulator codes and practices resulted in an attractive Levelized cost of electricity (LCOE) of US¢ 7.86/kWh over 25 years with a $151.5 million investment cost. The net savings to Lahore Waste Management Company can be $103.4 and $137.7 million respectively with and without tipping fees on account of waste disposal cost, bricks revenue using bottom ash, and waste fee. The project developers can get net savings of $16.9 and $51.5 million respectively with and without tipping fees other than LCOE. Furthermore, the greenhouse gas emissions of 216.6 million tons of CO2eq can be saved throughout plant life against 279 GWh/year energy generation, in terms of grid emission factor and current methane release into the atmosphere from the dumping site.
|
|
| 7. |
- Majeed, Khaliq, et al.
(författare)
-
Shuffled Complex Evolution-Based Performance Enhancement and Analysis of Cascade Liquefaction Process for Large-Scale LNG Production
- 2020
-
Ingår i: Energies. - : MDPI. - 1996-1073. ; 13:10
-
Tidskriftsartikel (refereegranskat)abstract
- Among all large-scale natural gas (NG) liquefaction processes, the mixed fluid cascade (MFC) process is recognized as a best-alternative option for the LNG production, mainly due its competitive performance. However, from a thermodynamic point of view, the MFC process is still far from its potential maximum energy efficiency due to non-optimal execution of design variables. Therefore, the energy efficiency enhancement of the MFC process remains an ongoing issue. The design optimization after fixing the main configuration of the process is one of the most economic, but challenging exercises during the design stages. In this study, shuffled complex evolution (SCE) is studied to find the optimal design of the MFC process corresponding to minimal energy consumption in refrigeration cycles. The MFC process is simulated using Aspen Hysys((R)) v10 and then coupled with the SCE approach, which is coded in MATLAB((R)) 2019a. The refrigerant composition and operating pressures for each cycle of the MFC process were optimized considering the approach temperature inside the LNG heat exchanger as a constraint. The resulting optimal MFC process saved 19.76% overall compression power and reduced the exergy destruction up to 28.76%. The thermodynamic efficiency (figure of merit) of the SCE-optimized process was 25% higher than that of the published base case. Furthermore, the optimization results also imply that there is a trade-off between the thermodynamic performance improvement and the computational cost (no. of iterations). In conclusion, SCE exhibited potential to improve the performance of highly nonlinear and complex processes such as LNG processes.
|
|
| 8. |
- Rafique, Asia, et al.
(författare)
-
Multioxide phase-based nanocomposite electrolyte (M@SDC where M = Zn2+ / Ba2+/ La2+/Zr-2/Al3+) materials
- 2020
-
Ingår i: Ceramics International. - : ELSEVIER SCI LTD. - 0272-8842 .- 1873-3956. ; 46:52, s. 6882-6888
-
Tidskriftsartikel (refereegranskat)abstract
- This paper deals with the development of a highly dense and stable electrolyte on the base of nanoionics oxide interface theory. This gives a comparative study of two-phase nanocomposite electrolytes that are developed for low temperature solid oxide fuel cells (LT-SOFCs). These nanocomposites are synthesised with different oxides, which are coated on the doped ceria that showed high oxide ion mobility for LT-SOFCs. These novel two-phase nanocomposite oxide ionic conductors (MCe0.8Sm0.2O2-MO2, where M = Zn2+/Ba2+/La3+/Zr2+/Al3+) were synthesised by a co-precipitation method. The interface study between these two phases was analysed by electrochemical impedance spectroscopy (EIS), while ionic conductivities were measured with DC conductivity (four probe method). The nanocomposite electrolytes exhibited higher conductivities with the increase of concentration of coated oxides but decreased at a certain level. The structural or morphological properties of the nanocomposite electrolytes were examined by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The thermal stability was investigated using thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The maximum performance of 590 mW/cm(2) at 550 degrees C was obtained for the Zn@SDC based cell, and the rest of the coated samples Ba@SDC, La@SDC, Zr@SDC and Al@SDC based cells showed values of 550 mW/cm(2), 540 mW/cm(2), 450 mW/cm(2), 340 mW/cm(2), respectively, with hydrogen as a fuel. Therefore, the coated-SDC based nanocomposite materials are a good approach for lowering the operating temperature to achieve the challenges of the solid oxide fuel cells (SOFC). These two-phase nanocomposite electrolytes satisfy the all requirements which one electrolyte should have, like high ionic conduction, thermodynamic stability and negligible electronic conduction.
|
|
| 9. |
- Wilkinson, John L., et al.
(författare)
-
Pharmaceutical pollution of the world's rivers
- 2022
-
Ingår i: Proceedings of the National Academy of Sciences of the United States of America. - : Proceedings of the National Academy of Sciences. - 0027-8424 .- 1091-6490. ; 119:8
-
Tidskriftsartikel (refereegranskat)abstract
- Environmental exposure to active pharmaceutical ingredients (APIs) can have negative effects on the health of ecosystems and humans. While numerous studies have monitored APIs in rivers, these employ different analytical methods, measure different APIs, and have ignored many of the countries of the world. This makes it difficult to quantify the scale of the problem from a global perspective. Furthermore, comparison of the existing data, generated for different studies/regions/continents, is challenging due to the vast differences between the analytical methodologies employed. Here, we present a global-scale study of API pollution in 258 of the world's rivers, representing the environmental influence of 471.4 million people across 137 geographic regions. Samples were obtained from 1,052 locations in 104 countries (representing all continents and 36 countries not previously studied for API contamination) and analyzed for 61 APIs. Highest cumulative API concentrations were observed in sub-Saharan Africa, south Asia, and South America. The most contaminated sites were in low- to middle-income countries and were associated with areas with poor wastewater and waste management infrastructure and pharmaceutical manufacturing. The most frequently detected APIs were carbamazepine, metformin, and caffeine (a compound also arising from lifestyle use), which were detected at over half of the sites monitored. Concentrations of at least one API at 25.7% of the sampling sites were greater than concentrations considered safe for aquatic organisms, or which are of concern in terms of selection for antimicrobial resistance. Therefore, pharmaceutical pollution poses a global threat to environmental and human health, as well as to delivery of the United Nations Sustainable Development Goals.
|
|
| 10. |
- Yaseen, Azeema, et al.
(författare)
-
Dimensionality Reduction for Internet of Things Using the Cuckoo Search Algorithm : Reduced Implications of Mesh Sensor Technologies
- 2020
-
Ingår i: Wireless Communications & Mobile Computing. - : WILEY-HINDAWI. - 1530-8669 .- 1530-8677. ; 2020
-
Tidskriftsartikel (refereegranskat)abstract
- The internet of things is used as a demonstrative keyword for evolution of the internet and physical realms, by means of pervasive distributed commodities with embedded identification, sensing, and actuation abilities. Imminent intellectual technologies are subsidizing internet of things for information transmission within physical and autonomous digital entities to provide amended services, leading towards a new communication era. Substantial amounts of heterogeneous hardware devices, e.g., radio frequency identification (RFID) tags, sensors, and various network protocols are exploited to support object identification and network communication. Data generated by these digital objects is termed as "Big Data" and incorporates high dimensional space with noisy, irrelevant, and redundant features. Direct execution of mining techniques onto such kind of high dimensionality attribute space can increase cost and complexity. Data analytic mechanisms are embedded into internet of things to permit intelligent decision-making capabilities. These notions have raised new challenges regarding internet of things from a data and algorithm perspective. The proposed study identifies the problem in the internet of things network and proposes a novel cuckoo search-based outdoor data management. The technique of the feature extraction is used for the extraction of expedient information from raw and high-dimensional data. After the implementation for the cuckoo search-based feature extraction, few test benchmarks are introduced to evaluate the performance of mutated cuckoo search algorithms. The consequential low-dimensional data optimizes classification accuracy along with reduced complexity and cost.
|
|
| 11. |
- Zheng, Xiaoxiao, et al.
(författare)
-
Graphene-Oxide-Based Fluoro- and Chromo-Genic Materials and Their Applications
- 2022
-
Ingår i: Molecules. - : MDPI AG. - 1431-5157 .- 1420-3049. ; 27:6
-
Tidskriftsartikel (refereegranskat)abstract
- Composite materials and their applications constitute a hot field of research nowadays due to the fact that they comprise a combination of the unique properties of each component of which they consist. Very often, they exhibit better performance and properties compared to their combined building blocks. Graphene oxide (GO), as the most widely used derivative of graphene, has attracted widespread attention because of its excellent properties. Abundant oxygen-containing functional groups on GO can provide various reactive sites for chemical modification or functionalization of GO, which in turn can be used to develop novel GO-based composites. This review outlines the most recent advances in the field of novel dyes and pigments encompassing GO as a key ingredient or as an important cofactor. The interactions of graphene with other materials/compounds are highlighted. The special structure and unique properties of GO have a great effect on the performance of fabricated hybrid dyes and pigments by enhancing the color performance of dyes, the anticorrosion properties of pigments, the viscosity and rheology of inks, etc., which further expands the applications of dyes and pigments in dyeing, optical elements, solar-thermal energy storage, sensing, coatings, and microelectronics devices. Finally, challenges in the current development as well as the future prospects of GO-based dyes and pigments are also discussed. This review provides a reference for the further exploration of novel dyes and pigments.
|
|
| 12. |
- Ahmad, Muhammad Ashfaq, et al.
(författare)
-
Structural and electrical characterisation of nanostructure electrodes for SOFCs
- 2014
-
Ingår i: International journal of hydrogen energy. - : Elsevier BV. - 0360-3199 .- 1879-3487. ; 39:30, s. 17487-17491
-
Tidskriftsartikel (refereegranskat)abstract
- This paper reports the effects of sintering temperature on structure, particle size and conductivity of electrodes (Sn0.2Zn0.8Fe0.2O & Sn0.8Zn0.2Fe0.2O). The electrode material was prepared by the chemical method combining a solid state reaction. Structural analyses were performed using X-ray diffraction and scanning electron microscopy. The particle size of the material obtained using Scherrer's formula was 50-60 nm and the nanostructure's surface was studied using electrochemical characterisations tools. Electrical conductivity was determined using the 4-probe DC method, which was compared with the 4-probe AC method. These results suggest a promising substitute for the conventional electrodes of solid oxide fuel cells (SOFCs). It is known that a sintering temperature above 1000 degrees C causes an increase in density and a reduction of porosity. Therefore, we optimised the sintering temperature at 1000 degrees C and obtained electrical conductivity of about 5 S Thus, this electrode could play a vital role in the development of high performance SOFCs at intermediate temperatures.
|
|
| 13. |
- Javaid, Nadeem, et al.
(författare)
-
An Enhanced Energy Balanced Data Transmission Protocol for Underwater Acoustic Sensor Networks
- 2016
-
Ingår i: Sensors. - : MDPI AG. - 1424-8220. ; 16:4
-
Tidskriftsartikel (refereegranskat)abstract
- This paper presents two new energy balanced routing protocols for Underwater Acoustic Sensor Networks (UASNs); Efficient and Balanced Energy consumption Technique (EBET) and Enhanced EBET (EEBET). The first proposed protocol avoids direct transmission over long distance to save sufficient amount of energy consumed in the routing process. The second protocol overcomes the deficiencies in both Balanced Transmission Mechanism (BTM) and EBET techniques. EBET selects relay node on the basis of optimal distance threshold which leads to network lifetime prolongation. The initial energy of each sensor node is divided into energy levels for balanced energy consumption. Selection of high energy level node within transmission range avoids long distance direct data transmission. The EEBET incorporates depth threshold to minimize the number of hops between source node and sink while eradicating backward data transmissions. The EBET technique balances energy consumption within successive ring sectors, while, EEBET balances energy consumption of the entire network. In EEBET, optimum number of energy levels are also calculated to further enhance the network lifetime. Effectiveness of the proposed schemes is validated through simulations where these are compared with two existing routing protocols in terms of network lifetime, transmission loss, and throughput. The simulations are conducted under different network radii and varied number of nodes.
|
|
| 14. |
- Rafique, Asia, et al.
(författare)
-
An efficient carbon resistant composite Ni0.6Zn0.4O2-delta-GDC anode for biogas fuelled solid oxide fuel cell
- 2019
-
Ingår i: Journal of Power Sources. - : ELSEVIER. - 0378-7753 .- 1873-2755. ; 438
-
Tidskriftsartikel (refereegranskat)abstract
- This paper describes the fabrication of Ni0.6Zn0.4-Gd0.2Ce0.8O2-delta (NiZn-GDC) via a two-step wet chemical synthesis technique. This composite was found to be more thermally stable and carbon resistive under the intense reducing environment of biogas. This was confirmed by different characterization techniques. The maximum power density P-max, was achieved at 600 degrees C as 820 mW/cm(2) and 548 mW/cm(2) with hydrogen and biogas, respectively. Different characterization techniques have been performed, such as X-ray diffractometry (XRD), scanning electron microscopy (SEM/EDX), UV visible spectroscopy, and Raman spectroscopy. The XRD pattern by Rietveld refinement showed two-phase structures of the anode composite with an average crystallite size of 25 35 nm before and after reduction with methane. The optical band gap (E-g(opt)) of NiZn-GDC was calculated to be 2.24eV from the Tauc plot using absorbance data. The Nyquist plot was also drawn to study the AC electrochemical impedance spectra (EIS) of the nanocomposite anode from 450 degrees C to 600 degrees C in air. The maximum DC conductivity of 1.37 S/cm was observed at a temperature of 600 degrees C using the four-probe DC technique.
|
|
