| 1. |
|
|
| 2. |
|
|
| 3. |
|
|
| 4. |
|
|
| 5. |
|
|
| 6. |
|
|
| 7. |
|
|
| 8. |
|
|
| 9. |
|
|
| 10. |
|
|
| 11. |
- Mushtaq, I, et al.
(författare)
-
A unique amphiphilic triblock copolymer, nontoxic to human blood and potential supramolecular drug delivery system for dexamethasone
- 2021
-
Ingår i: Scientific reports. - : Springer Science and Business Media LLC. - 2045-2322. ; 11:1, s. 21507-
-
Tidskriftsartikel (refereegranskat)abstract
- The drug delivery system (DDS) often causes toxicity, triggering undesired cellular injuries. Thus, developing supramolecules used as DDS with tunable self-assembly and nontoxic behavior is highly desired. To address this, we aimed to develop a tunable amphiphilic ABA-type triblock copolymer that is nontoxic to human blood cells but also capable of self-assembling, binding and releasing the clinically used drug dexamethasone. We synthesized an ABA-type amphiphilic triblock copolymer (P2L) by incorporating tetra(aniline) TANI as a hydrophobic and redox active segment along with monomethoxy end-capped polyethylene glycol (mPEG2k; Mw = 2000 g mol−1) as biocompatible, flexible and hydrophilic part. Cell cytotoxicity was measured in whole human blood in vitro and lung cancer cells. Polymer-drug interactions were investigated by UV–Vis spectroscopy and computational analysis. Our synthesized copolymer P2L exhibited tuned self-assembly behavior with and without external stimuli and showed no toxicity in human blood samples. Computational analysis showed that P2L can encapsulate the clinically used drug dexamethasone and that drug uptake or release can also be triggered under oxidation or low pH conditions. In conclusion, copolymer P2L is nontoxic to human blood cells with the potential to carry and release anticancer/anti-inflammatory drug dexamethasone. These findings may open up further investigations into implantable drug delivery systems/devices with precise drug administration and controlled release at specific locations.
|
|
| 12. |
|
|
| 13. |
- Hafeez, Abdul, et al.
(författare)
-
Synthesis, Crystal Structures, and Spectroscopic Characterization of Bis-aldehyde Monomers and Their Electrically Conductive Pristine Polyazomethines
- 2019
-
Ingår i: Polymers. - : MDPI. - 2073-4360. ; 11:9
-
Tidskriftsartikel (refereegranskat)abstract
- Bis-aldehyde monomers 4-(4′-formyl-phenoxy)benzaldehyde (3a), 3-methoxy-4-(4′-formyl-phenoxy)benzaldehyde (3b), and 3-ethoxy-4-(4′-formyl-phenoxy)benzaldehyde (3c) were synthesized by etherification of 4-fluorobenzaldehyde (1) with 4-hydroxybenzaldehyde (2a), 3-methoxy-4-hydroxybenzaldehyde (2b), and 3-ethoxy-4-hydroxybenzaldehyde (2c), respectively. Each monomer was polymerized with p-phenylenediamine and 4,4′-diaminodiphenyl ether to yield six poly(azomethine)s. Single crystal X-ray diffraction structures of 3b and 3c were determined. The structural characterization of the monomers and poly(azomethine)s was performed by FT-IR and NMR spectroscopic techniques and elemental analysis. Physicochemical properties of polymers were investigated by powder X-ray diffraction, thermogravimetric analysis (TGA), viscometry, UV–vis, spectroscopy and photoluminescence. These polymers were subjected to electrical conductivity measurements by the four-probe method, and their conductivities were found to be in the range 4.0 × 10−5 to 6.4 × 10−5 Scm−1, which was significantly higher than the values reported so far.
|
|
| 14. |
- Jlassi, Khouloud, et al.
(författare)
-
Highly sensitive humidity sensor based on cadmium selenide quantum dots-polymer composites : synthesis, characterization, and effect of UV/ozone treatment
- 2023
-
Ingår i: Journal of Materials Science: Materials in Electronics. - 0957-4522. ; 34:21
-
Tidskriftsartikel (refereegranskat)abstract
- This work describes the rational design of thin film-based cadmium selenide quantum dots (CdSe) mixed with conductive polyvinylidene fluoride (PVDF), inducing PVDF-CdSe composite for potential resistive humidity-sensing applications. The effect of UV/ozone treatment on surface hydrophilicity and sensing properties was investigated. AFM has been performed to examine the prepared films' texture, distribution over the surface, and size. Overall, the hydrophilicity of the developed films increases with UV radiation exposure time, leading to enhanced water vapor absorption without deforming the film surface. The sensor's sensitivity is improved with increasing UV radiation exposure. The electrical response of the PVDF-CdSe humidity sensors after 30 min of UV/ozone treatment reveals that at higher humidity levels (i.e., > 80% RH), the sensors exhibit an irregular response. However, at 20 min, treatment increases sensitivity and a linear change in impedance response concerning humidity level change compared to other samples. The hysteresis response was divided into two regions: the lower region, between 30 and 60% RH—where the maximum hysteresis loss was calculated to be 3%. While the higher area between 60 and 90% RH, where the maximum estimated hysteresis loss of the PVDF-CdSe sensor is around 14%, the UV/ozone treatment of the PVDF-CdSe nanocomposite film was found to enhance the sensing film's hydrophilicity without deforming the surface of the as-prepared PVDF-CdSe as well as the UV-treated films validates a potential for novel humidity sensors.
|
|
