| 1. |
- Antonsson, Hanna, 1979-
(författare)
-
Chefers arbete i äldreomsorgen – att hantera den svårhanterliga omvärlden : Relationen mellan arbete och organisering
- 2013
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- I avhandlingen beskrivs och analyseras chefers arbete genom att kombinera individuella perspektiv med organisatoriska och samhälleliga perspektiv vilket ger både teoretiska och praktiska implikationerReferensramen är uppbyggd av teorier kring chefers arbete och nyinstitutionell teori av Skandinaviskt slag.Flera metoder kombineras för att fånga komplexiteten i chefers arbete; skuggningar, intervjuer, observationer och dokumentstudier.Forskningsfrågorna besvaras genom att använda en kombination av teorier utvecklade för olika analysnivåer; individ, organisation och samhälle. De empiriska materialen används för att ge ett bidrag till vidare forskning om chefers arbete med en empirisk bas.Vikten av att relatera chefers arbete till den kontext som omger dem betonas. Chefers arbete i äldreomsorgen har specifika karaktäristika men också gemensamma drag med chefers arbete i andra sektorer och på andra organisatoriska nivåer. I det empiriska materialet har flera organisatoriska karaktäristika som påverkar chefers arbete identifierats. Beskrivningarna av chefers arbete bidrar också till en utveckling av en empirinära praxisteori för chefers arbete. Med hjälp av nyinstitutionell teori beskrivs hur chefer möter skilda förväntningar och krav och i organisationer, där dessa inte överensstämmer måste chefer hantera ett organisatoriskt hyckleri.
|
|
| 2. |
- Antonsson, Stefan, et al.
(författare)
-
Adding lignin derivatives to decrease the effect of mechano-sorptive creep in linerboard
- 2008
-
Ingår i: Appita journal. - 1038-6807. ; 61:6, s. 468-471
-
Tidskriftsartikel (refereegranskat)abstract
- When load is applied to any type of paper while varying the relative humidity, the paper will creep more than if the same load is applied at constant humidity. This behaviour is called mechano-sorptive creep or accelerated creep, and the reasons for its occurrence in paper are still not fully understood. However, wet strength and the addition of apolar (hydrophobic) compounds to sheets have previously been suggested as factors improving the mechano-sorptive creep performance. This work evaluates a method for improving wet strength and tests the addition of a hydrophobic compound, with particular reference to mechano-sorptive creep stiffness. Wet strength was improved by subjecting kraft liner pulp to low-molecular-weight lignin, obtained by cross-flow filtration, and to the radical initiator manganese(III). The hydrophobic compound added was a suberin-like lignin derivative. Adding the suberin-like lignin derivative significantly increased the mechano-sorptive creep stiffness, even though the stiffness at 90% rh decreased in the tested samples. This was probably because of the decrease in hygroexpansion caused by this hydrophobic additive. Even though it is possible significantly to increase the wet strength of kraft liner pulp by adding manganese(III) and cross-flow-filtered lignin, doing so has no significant effect on mechano-sorptive creep stiffness.
|
|
| 3. |
- Antonsson, Stefan, et al.
(författare)
-
Applying a novel cooking technique to produce high kappa number pulps : the effects on physical properties
- 2009
-
Ingår i: Nordic Pulp & Paper Research Journal. - : Walter de Gruyter GmbH. - 0283-2631 .- 2000-0669. ; 24:4, s. 415-420
-
Tidskriftsartikel (refereegranskat)abstract
- A recently developed kraft cooking technique, with a longer impregnation time at lower temperatures to facilitate diffusion over consumption of active cooking chemicals, makes it possible to produce kraftliner pulp without inline refining. This technique was applied to prepare two pulps with different lignin contents, which were compared with two industrial pulps from conventional kraft cooks in order to evaluate the physical properties of the pulps. It was demonstrated that pulps with lower lignin content can increase tensile stiffness, decrease hygroexpansion, and decrease the mechano-sorptive creep of handsheets. However, no difference in SCT and tensile energy absorption values due to different lignin contents was observed. It was further demonstrated that pulps made with Extended Impregnation Cooking (EIC) results in straighter pulp fibres with higher cellulose content. These pulps tended to have lower mechano-sorptive creep than conventional pulps. A higher brightness of the pulp sheets can also be obtained by choosing a higher alkali profile.
|
|
| 4. |
- Antonsson, Stefan, et al.
(författare)
-
Biomimetic synthesis of suberin for new biomaterials
- 2005
-
Ingår i: Appita Annual Conference. ; , s. 561-564
-
Konferensbidrag (refereegranskat)abstract
- Suberin is the biopolymer giving cork (oak bark) its hydrophobic and resistant characteristics. It acts as a diffusion barrier in bark and roots of plants. Similarly to lignin, it is a phenolic polymer with good affinity to cellulose and other wood polysaccharides, but it also contains polyaliphatic and strongly hydrophobic elements. In order to produce a lignin derivative similar to suberin, a desired lignin starting material should be of low molecular weight and have a high content of hydroxylic phenolic groups. By means of cross flow nanofiltration of softwood kraft pulping black liquor and pH-precipitation with diluted sulphuric acid, such a lignin has been obtained. Due to the fact that too much organics entering the recovery boiler frequently is the bottleneck for pulp production increases, a removal of part of the lignin can be economically very favourable. By using this lignin together with linola oil, a linseed oil with a large amount of unsaturated structures, an attempt was made to create a new hydrophobic lignin derivative similar tosuberin. The product was analysed with FT-IR, Fourier Transformed Infra Red Spectroscopy and GPC, Gel Permeation Chromatography. The suberin like material obtained from this lignin could be polymerised on thermo mechanical pulp fibres by means of Mn(III)-driven phenolic coupling. The ability of the suberin monomers to act as a hydrophobic paper coating was evaluated with contact angle measurements and the results indicate that this lignin derivative was potentially of interest due to its capability to interact well with wood fibres and make paper hydrophobic.
|
|
| 5. |
- Antonsson, Stefan, et al.
(författare)
-
Comparison of the physical properties between hardwood and softwood pulps
- 2009
-
Ingår i: Nordic Pulp & Paper Research Journal. - 0283-2631 .- 2000-0669. ; 24:4, s. 409-414
-
Tidskriftsartikel (refereegranskat)abstract
- High mechano-sorptive creep resistance, i.e., good creep resistance in environments with changing relative humidity, is one of the key requirements for linerboards. The aim of this study was to investigate the influence of pulp types and pulp properties on the mechano-sorptive creep of kraftliner. A high-yield softwood, kraftliner pulp, and four different hardwood pulps were investigated. The physical properties of laboratory sheets were evaluated, with emphasis on the mechano-sorptive creep properties.The results showed that the density increase due to increased beating significantly improved the tensile stiffness of all pulps, while its effect on the isocyclic creep stiffness was less pronounced. The hardwood pulps showed higher tensile stiffness, better mechano-sorptive creep properties, and lower hygroexpansion than the softwood pulp at a given density. However, the softwood pulp did exhibit better tensile strength and fracture toughness properties than the hardwood pulps.The results imply that hardwood pulps can be competitive with softwood pulps in kraftliners, provided that their tensile strength and fracture toughness properties can be improved by, for example, chemical means. Furthermore, the isocyclic creep stiffness correlates with the ratio of tensile stiffness to hygroexpansion, indicating that this ratio can be used for engineering estimates of the mechano-sorptive creep performance of paper materials.
|
|
| 6. |
- Antonsson, Stefan, et al.
(författare)
-
Low Mw-lignin fractions together with vegetable oils as available oligomers for novel paper-coating applications as hydrophobic barrier
- 2008
-
Ingår i: Industrial crops and products (Print). - : Elsevier BV. - 0926-6690 .- 1872-633X. ; 27:1, s. 98-103
-
Tidskriftsartikel (refereegranskat)abstract
- Lignin residues are available in large amounts as kraft lignin from chemical pulping processes. This lignin is mainly incinerated in recovery boilers. The recovery boilers are often the bottle-necks in the overall pulping process when pulp production increases are desired. Through cross-flow nano-filtration of the black liquor from kraft pulping, a low-molecular weight lignin fraction can be removed thus decreasing the organic load on the recovery boilers. The low-molecular weight lignin fraction furthermore exhibit different characteristics compared to other commercial kraft lignins and represents a new raw material source in novel applications. The low-molecular weight lignin was used together with a vegetable oil to produce a new hydrophobic lignin derivative similar to suberin. The lignin and the lignin derivative was analysed with FT-IR, UV-vis and SEC. The ability of the product to make paper surfaces hydrophobic was also evaluated. The results demonstrate the possibility to make a suberin-like lignin derivative that is potentially of interest in paper-coating applications due to its capability to interact well with wood fibres and make paper hydrophobic.
|
|
| 7. |
- Antonsson, Stefan, 1979-
(författare)
-
Strategies for improving kraftliner pulp properties
- 2008
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- A large part of the world paper manufacturing consists of production of corrugated board components, kraftliner and fluting, that are used in many different types of corrugated boxes. Because these boxes are stored and transported, they are often subjected to changes in relative humidity. These changes together with mechanical loads will increase the deformation of the boxes compared to the case where the same loads are applied in a static environment. This enlarged creep due to the changes in relative humidity is called mechano-sorptive or accelerated creep. Mechano-sorptive creep forces producers to use high safety factors when designing boxes, and therefore, this is one of the key properties of kraftliner boards. Different strategies to decrease mechano-sorptive creep, and to simultaneously gain more knowledge about the causes for this phenomenon in paper, are the aim of this work. Derivatised and underivatised black liquor lignins, a by-product produced in pulp mills in large quantities, have been used together with biomimetic methods, to modify the properties of kraftliner pulp. Furthermore, the properties of kraftliner pulp have been compared to other pulps in order to evaluate the influence of fibre morphological factors, such as fibre width and shape factor, on the mechano-sorptive creep. In addition the influence of the chemical composition of the kraftliner pulp has been evaluated both by means of treating a kraftliner pulp with chlorite and xylanase and by producing pulps with different chemical composition. By using lignin and biomimetic methods, to create radical coupling reactions, it has been shown that it is possible to increase the wet strength of kraftliner pulp sheets. This method of treating the pulp showed, however, no significant effects on the mechano-sorptive creep. The addition of an apolar suberin-like lignin derivative, which has been shown to be possible to produce from natural resources, did show a positive effect on mechano-sorptive creep properties, but at the expense of stiffness properties in constant climate. Different pulps were compared with a kraftliner pulp and it was observed that the ratio between tensile stiffness and hygroexpansion can be used to estimate the mechano-sorptive creep properties. The hardwood kraft pulps investigated had lower hygroexpansion, probably due to more slender and straighter fibres, and higher tensile stiffness, probably due to lower lignin content. As the lignin content was varied by different methods in kraft pulps, it was observed that increased lignin content gives an increased hygroexpansion and decreased tensile stiffness as well as an increased mechano-sorptive creep. There were also indications of increased mechano-sorptive creep due to higher xylan content.
|
|
| 8. |
- Antonsson, Stefan, et al.
(författare)
-
The influence of lignin and xylan on some kraftliner pulp properties
- 2009
-
Ingår i: Nordic Pulp & Paper Research Journal. - : Walter de Gruyter GmbH. - 0283-2631 .- 2000-0669. ; 24:4, s. 403-408
-
Tidskriftsartikel (refereegranskat)abstract
- This study investigates the influence of lignin and hemicellulose content on the mechanical and physical properties of softwood kraft liner pulp. Tensile properties, hygroexpansion, and mechano-sorptive creep properties were measured. The lignin and hemicellulose contents were modified by chlorite delignification and xylanase treatment. After treatment, the chemical composition of the pulps was 3-14% Klason lignin, 69-77% cellulose, 16-21% hemicellulose, and 4-7% xylan. In the tested pulps, low lignin content tended to decrease hygroexpansion as well as increase tensile stiffness and mechano-sorptive creep stiffness. Xylan contributed less to the pulp sheet properties, but at equal lignin contents, higher xylan content tended to give increased hygroexpansion and worse mechano-sorptive creep properties.
|
|
| 9. |
- Antonsson, Stefan, et al.
(författare)
-
The relationship between hygroexpansion, tensile stiffness, and mechano–sorptive creep in bleached hardwood kraft pulps
- 2010
-
Ingår i: Appita journal. - 1038-6807. ; 63:1, s. 231-
-
Tidskriftsartikel (refereegranskat)abstract
- Hygroexpansion coefficient and tensile stiffness are important parameters in many paper applications. This study compares several bleached industrial hardwood kraft pulps, comprising five eucalypt pulps from South America, Europe, and Africa as well as an acacia pulp from Asia and a birch pulp from Scandinavia. Refined and unrefined pulps are compared. The results indicate significant differences in hygroexpansion but smaller differences in tensile stiffness index at comparable densities. No single factor offering a reasonable explanation of these differences in hygroexpansion coefficient, such as carbohydrate composition, fibre dimensions, or fibre form, was found. However, correlation between hygroexpansion coefficient and the mechano-sorptive creep stiffness was observed. We suggest that the hygroexpansion coefficient at a given tensile stiffness level can be used to rank pulps in terms of their mechano-sorptive creep properties.
|
|
| 10. |
- Antonsson, Stefan, 1979-
(författare)
-
The Use of Lignin Derivatives to Improve Selected Paper Properties
- 2007
-
Licentiatavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Ved består huvudsakligen av tre typer av polymerer, cellulosa, hemicellulosa och lignin. Lignin bildas i naturen genom enzymatiskt initierad oxidativ koppling av tre olika typer av fenylpropan-enheter. Dessa bygger genom olika kol-kol- och kol-syre-bindningar upp en amorf tredimensionell polymer. När kemisk massa tillverkas bryts lignin ner och löses ut i kokluten. Luten innehåller de förbrukade kokkemikalierna och bränns generellt i en sodapanna för att regenerera kemikalierna och producera ånga. Sodapannan är emellertid dyr. Därför har den blivit produktionsbegränsande på många massabruk. Att avlägsna en del av ligninet från avluten vore därför önskvärt och att finna ekonomiskt intressanta produkter baserade på lignin från svartlut är därför ett viktigt forskningsområde . Ett lämpligt område för ligninprodukter vore som tillsatts i oblekt massa. Oblekt massa används till stor del för tillverkning av kraftliner, topp- och bottenskikten på wellpapp. När lådor av wellpapp lagras i containrar som färdas över haven, förändras den relativa luftfuktigheten. Detta gör att lådorna kollapsar lättare än om de skulle ha lagrats vid konstant luftfuktighet, även en hög sådan. Detta är på grund av det så kallade mekanosorptiva- eller accelererade krypfenomenet. Genom tillsatts av våtstyrkemedel till kraftliner eller behandla den med hydrofoba ämnen, finns indikatoner på att mekanosorptiva effekten skulle kunna minska. För att försöka minska den effekten har ett lågmolekylärt kraftlignin, som utvunnits med hjälp av tvärsflödesfiltrering av svartlut och svavelsyrafällning, använts. Genom derivatisering av detta lignin med linolja erhölls ett hydrofobt ligninderivat som uppvisar strukturella likheter med biopolymeren suberin. När detta suberinlika ligninderivat tillsätts till massa verkar det mekanosorptiva krypet minska. När lågmolekylärt lignin används tillsammans med ligninradikalinitiatorerna lackas eller mangan(III) i kraftlinermassa erhålls dessutom en våtstyrka på ca 5% av torrstyrkan. Efter aminering av detta lignin gav en tillsatts till kraftlinermassan en våtstyrka på upp till 10% av torrstyrkan. Det finns indikationer på att det mekanosorptiva krypet samtidigt minskar när dessa behandlingar görs som ger upphov till ökad våtstyrka.
|
|
| 11. |
|
|
| 12. |
- Elegir, Graziano, et al.
(författare)
-
Laccase-initiated cross-linking of lignocellulose fibres using a ultra-filtered lignin isolated from kraft black liquor
- 2007
-
Ingår i: Applied Microbiology and Biotechnology. - : Springer Science and Business Media LLC. - 0175-7598 .- 1432-0614. ; 77:4, s. 809-817
-
Tidskriftsartikel (refereegranskat)abstract
- In this work, the effect of Trametes pubescens laccase (TpL) used in combination with a low-molecular-weight ultra-filtered lignin (UFL) to improve mechanical properties of kraft liner pulp and chemi-thermo-mechanical pulp was studied. UFL was isolated by ultra-filtration from the kraft cooking black liquor obtained from softwood pulping. This by-product from the pulp industry contains an oligomeric lignin with almost twice the amount of free phenolic moieties than residual kraft pulp lignin. The reactivity of TpL on UFL and kraft pulp was studied by nuclear magnetic resonance spectroscopy and size exclusion chromatography. Laccase was shown to polymerise UFL and residual kraft pulp lignin in the fibres, seen by the increase in their average molecular weight and in the case of UFL as a decrease in the amount of phenolic hydroxyls. The laccase initiated cross-linking of lignin, mediated by UFL, which gives rise to more than a twofold increase in wet strength of kraft liner pulp handsheets without loosing other critical mechanical properties. Hence, this could be an interesting path to decrease mechano-sorptive creep that has been reported to lessen in extent as wet strength is given to papers. The laccase/2,2'azino-bis(3-ethylbenzothiazoline-6-sulphonic acid) (ABTS) mediator system showed a greater increase in wet tensile strength of the resulting pulp sheets than the laccase/UFL system. However, other mechanical properties such as dry tensile strength, compression strength and Scott Bond internal strength were negatively affected by the laccase/ABTS system.
|
|
| 13. |
- Wedin, Helena, et al.
(författare)
-
Influence Of Xylan Content On The Oxygen Delignification Performance Of Eucalypt Kraft Pulps As Studied Using Prehydrolysis And Xylanase Treatments
- 2012
-
Ingår i: BioResources. - : BioResources. - 1930-2126. ; 7:4, s. 5527-5541
-
Tidskriftsartikel (refereegranskat)abstract
- Common metrics for evaluating the efficiency of oxygen delignification include the kappa number and Klason lignin content. As a change in xylan content often leads to a change in HexA content, the kappa number must be corrected for the HexA contribution before evaluating the degree of oxygen delignification when trying to understand the process in detail. Questions could also be raised about the accuracy of the Klason lignin method for oxygen-delignified hardwood kraft pulps, since the amount of residual lignin is small in such pulp. This study investigates the influence of xylan content on oxygen delignification efficiency in Eucalyptus urograndis kraft pulps. Xylan content was varied using two methods: treatment with xylanase and with acid prehydrolysis for various times before kraft cooking. The degree of oxygen delignification, expressed as the HexA-corrected kappa number, indicated no significant trend with xylan removal, and no significant trend was evident when expressed as Klason lignin content.
|
|
| 14. |
- Yavari, Nazila, et al.
(författare)
-
In vitro measurements of optical properties of porcine brain using a novel compact device
- 2005
-
Ingår i: Medical and Biological Engineering and Computing. - : Springer. - 0140-0118 .- 1741-0444. ; 43:5, s. 658-666
-
Tidskriftsartikel (refereegranskat)abstract
- Knowledge of the optical properties of tissues can be applied in numerous medical and scientific fields, including cancer diagnostics and therapy. There are many different ways of determining the optical properties of turbid media. The paper describes measurements of the optical properties of porcine brain tissue using novel instrumentation for simultaneous absorption and scattering characterisation of small turbid samples. Integrating sphere measurements are widely used as a reference method for determination of the optical properties of relatively thin turbid samples. However, this technique is associated with bulky equipment, complicated measuring techniques, interference compensation techniques and inconvenient sample handling. It is believed that the sphere for some applications can be replaced by a new, compact device, called the combined angular and spatially resolved head sensor, to measure the optical properties of thin turbid samples. The results compare very well with data obtained with an integrating sphere for well-defined samples. The instrument was shown to be accurate to within 12% for μa and 1% for μ s ′ in measurements of intralipid-ink samples. The corresponding variations of data were 17% and 2%, respectively. The reduced scattering coefficient for porcine white matter was measured to be 100 cm−1 at 633 nm, and the value for coagulated brain tissue was 65 cm−1. The corresponding absorption coefficients were 2 and 3 cm−1, respectively.
|
|
| 15. |
- Yavari, Nazila, et al.
(författare)
-
Measurements of optical properties of pig brain tissue in vitro using a novel compact device
- 2005
-
Ingår i: Progress in Biomedical Optics and Imaging - Proceedings of SPIE. - : SPIE. - 1605-7422 .- 1042-4687. ; 5864, s. 1-11
-
Konferensbidrag (refereegranskat)abstract
- In numerous medical and scientific fields, knowledge of the optical properties of tissues can be applied. Among many different ways of determining the optical properties of turbid media; integrating sphere measurements are widely used. However, this technique is associated with bulky equipment, complicated measuring techniques, interference compensation techniques, and inconvenient sample handling. This paper describes measurements of the optical properties of porcine brain tissue using novel instrumentation for simultaneous absorption and scattering characterization of small turbid samples. The system used measures both angularly and spatially resolved transmission and reflection and is called Combined Angular and Spatially-resolved Head (CASH) sensor. The results compare very well with data obtained with an integrating sphere for well-defined samples. The instrument was shown to be accurate to within 12 % for μa. and 1 % for μs' in measurements of intralipid-ink samples. The corresponding variations of data were 17 %, and 2 %, respectively. The reduced scattering coefficient for porcine white matter was measured to be 100 cm-1, while the value for coagulated brain tissue was 65 cm-1. The corresponding absorption coefficients were 2 and 3 cm-1, respectively. © 2005 SPIE and OSA.
|
|
