1. |
- Romanelli, F, et al.
(författare)
-
Overview of the JET results
- 2011
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 51:9
-
Tidskriftsartikel (refereegranskat)abstract
- Since the last IAEA Conference JET has been in operation for one year with a programmatic focus on the qualification of ITER operating scenarios, the consolidation of ITER design choices and preparation for plasma operation with the ITER-like wall presently being installed in JET. Good progress has been achieved, including stationary ELMy H-mode operation at 4.5 MA. The high confinement hybrid scenario has been extended to high triangularity, lower ρ*and to pulse lengths comparable to the resistive time. The steady-state scenario has also been extended to lower ρ*and ν*and optimized to simultaneously achieve, under stationary conditions, ITER-like values of all other relevant normalized parameters. A dedicated helium campaign has allowed key aspects of plasma control and H-mode operation for the ITER non-activated phase to be evaluated. Effective sawtooth control by fast ions has been demonstrated with3He minority ICRH, a scenario with negligible minority current drive. Edge localized mode (ELM) control studies using external n = 1 and n = 2 perturbation fields have found a resonance effect in ELM frequency for specific q95values. Complete ELM suppression has, however, not been observed, even with an edge Chirikov parameter larger than 1. Pellet ELM pacing has been demonstrated and the minimum pellet size needed to trigger an ELM has been estimated. For both natural and mitigated ELMs a broadening of the divertor ELM-wetted area with increasing ELM size has been found. In disruption studies with massive gas injection up to 50% of the thermal energy could be radiated before, and 20% during, the thermal quench. Halo currents could be reduced by 60% and, using argon/deuterium and neon/deuterium gas mixtures, runaway electron generation could be avoided. Most objectives of the ITER-like ICRH antenna have been demonstrated; matching with closely packed straps, ELM resilience, scattering matrix arc detection and operation at high power density (6.2 MW m-2) and antenna strap voltages (42 kV). Coupling measurements are in very good agreement with TOPICA modelling. © 2011 IAEA, Vienna.
|
|
2. |
- Abel, I, et al.
(författare)
-
Overview of the JET results with the ITER-like wall
- 2013
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 53:10, s. 104002-
-
Tidskriftsartikel (refereegranskat)abstract
- Following the completion in May 2011 of the shutdown for the installation of the beryllium wall and the tungsten divertor, the first set of JET campaigns have addressed the investigation of the retention properties and the development of operational scenarios with the new plasma-facing materials. The large reduction in the carbon content (more than a factor ten) led to a much lower Z(eff) (1.2-1.4) during L- and H-mode plasmas, and radiation during the burn-through phase of the plasma initiation with the consequence that breakdown failures are almost absent. Gas balance experiments have shown that the fuel retention rate with the new wall is substantially reduced with respect to the C wall. The re-establishment of the baseline H-mode and hybrid scenarios compatible with the new wall has required an optimization of the control of metallic impurity sources and heat loads. Stable type-I ELMy H-mode regimes with H-98,H-y2 close to 1 and beta(N) similar to 1.6 have been achieved using gas injection. ELM frequency is a key factor for the control of the metallic impurity accumulation. Pedestal temperatures tend to be lower with the new wall, leading to reduced confinement, but nitrogen seeding restores high pedestal temperatures and confinement. Compared with the carbon wall, major disruptions with the new wall show a lower radiated power and a slower current quench. The higher heat loads on Be wall plasma-facing components due to lower radiation made the routine use of massive gas injection for disruption mitigation essential.
|
|
3. |
|
|
4. |
- Bécoulet, A., et al.
(författare)
-
Science and technology research and development in support to ITER and the Broader Approach at CEA
- 2013
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 53:10
-
Tidskriftsartikel (refereegranskat)abstract
- In parallel to the direct contribution to the procurement phase of ITER and Broader Approach, CEA has initiated research & development programmes, accompanied by experiments together with a significant modelling effort, aimed at ensuring robust operation, plasma performance, as well as mitigating the risks of the procurement phase. This overview reports the latest progress in both fusion science and technology including many areas, namely the mitigation of superconducting magnet quenches, disruption-generated runaway electrons, edge-localized modes (ELMs), the development of imaging surveillance, and heating and current drive systems for steady-state operation. The WEST (W Environment for Steady-state Tokamaks) project, turning Tore Supra into an actively cooled W-divertor platform open to the ITER partners and industries, is presented.
|
|
5. |
- Klionsky, Daniel J., et al.
(författare)
-
Guidelines for the use and interpretation of assays for monitoring autophagy
- 2012
-
Ingår i: Autophagy. - : Informa UK Limited. - 1554-8635 .- 1554-8627. ; 8:4, s. 445-544
-
Forskningsöversikt (refereegranskat)abstract
- In 2008 we published the first set of guidelines for standardizing research in autophagy. Since then, research on this topic has continued to accelerate, and many new scientists have entered the field. Our knowledge base and relevant new technologies have also been expanding. Accordingly, it is important to update these guidelines for monitoring autophagy in different organisms. Various reviews have described the range of assays that have been used for this purpose. Nevertheless, there continues to be confusion regarding acceptable methods to measure autophagy, especially in multicellular eukaryotes. A key point that needs to be emphasized is that there is a difference between measurements that monitor the numbers or volume of autophagic elements (e.g., autophagosomes or autolysosomes) at any stage of the autophagic process vs. those that measure flux through the autophagy pathway (i.e., the complete process); thus, a block in macroautophagy that results in autophagosome accumulation needs to be differentiated from stimuli that result in increased autophagic activity, defined as increased autophagy induction coupled with increased delivery to, and degradation within, lysosomes (in most higher eukaryotes and some protists such as Dictyostelium) or the vacuole (in plants and fungi). In other words, it is especially important that investigators new to the field understand that the appearance of more autophagosomes does not necessarily equate with more autophagy. In fact, in many cases, autophagosomes accumulate because of a block in trafficking to lysosomes without a concomitant change in autophagosome biogenesis, whereas an increase in autolysosomes may reflect a reduction in degradative activity. Here, we present a set of guidelines for the selection and interpretation of methods for use by investigators who aim to examine macroautophagy and related processes, as well as for reviewers who need to provide realistic and reasonable critiques of papers that are focused on these processes. These guidelines are not meant to be a formulaic set of rules, because the appropriate assays depend in part on the question being asked and the system being used. In addition, we emphasize that no individual assay is guaranteed to be the most appropriate one in every situation, and we strongly recommend the use of multiple assays to monitor autophagy. In these guidelines, we consider these various methods of assessing autophagy and what information can, or cannot, be obtained from them. Finally, by discussing the merits and limits of particular autophagy assays, we hope to encourage technical innovation in the field.
|
|
6. |
- Pucella, G., et al.
(författare)
-
Overview of the FTU results
- 2022
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 62:4
-
Forskningsöversikt (refereegranskat)abstract
- Since the 2018 IAEA FEC Conference, FTU operations have been devoted to several experiments covering a large range of topics, from the investigation of the behaviour of a liquid tin limiter to the runaway electrons mitigation and control and to the stabilization of tearing modes by electron cyclotron heating and by pellet injection. Other experiments have involved the spectroscopy of heavy metal ions, the electron density peaking in helium doped plasmas, the electron cyclotron assisted start-up and the electron temperature measurements in high temperature plasmas. The effectiveness of the laser induced breakdown spectroscopy system has been demonstrated and the new capabilities of the runaway electron imaging spectrometry system for in-flight runaways studies have been explored. Finally, a high resolution saddle coil array for MHD analysis and UV and SXR diamond detectors have been successfully tested on different plasma scenarios.
|
|
7. |
|
|
8. |
|
|
9. |
- Demetris, A J, et al.
(författare)
-
2016 Comprehensive Update of the Banff Working Group on Liver Allograft Pathology: Introduction of Antibody-Mediated Rejection.
- 2016
-
Ingår i: American journal of transplantation : official journal of the American Society of Transplantation and the American Society of Transplant Surgeons. - : Elsevier BV. - 1600-6143. ; 16:10, s. 2816-2835
-
Tidskriftsartikel (refereegranskat)abstract
- The Banff Working Group on Liver Allograft Pathology reviewed and discussed literature evidence regarding antibody-mediated liver allograft rejection at the 11th (Paris, France, June 5-10, 2011), 12th (Comandatuba, Brazil, August 19-23, 2013), and 13th (Vancouver, British Columbia, Canada, October 5-10, 2015) meetings of the Banff Conference on Allograft Pathology. Discussion continued online. The primary goal was to introduce guidelines and consensus criteria for the diagnosis of liver allograft antibody-mediated rejection and provide a comprehensive update of all Banff Schema recommendations. Included are new recommendations for complement component 4d tissue staining and interpretation, staging liver allograft fibrosis, and findings related to immunosuppression minimization. In an effort to create a single reference document, previous unchanged criteria are also included.
|
|
10. |
- Soust-Verdaguer, B., et al.
(författare)
-
Implications of using systematic decomposition structures to organize building LCA information: A comparative analysis of national standards and guidelines- IEA EBC ANNEX 72
- 2020
-
Ingår i: IOP Conference Series: Earth and Environmental Science. - : IOP Publishing. - 1755-1307 .- 1755-1315. ; 588:2
-
Konferensbidrag (refereegranskat)abstract
- Introduction: The application of the Life Cycle Assessment (LCA) technique to a building requires the collection and organization of a large amount of data over its life cycle. The systematic decomposition method can be used to classify building components, elements and materials, overcome specific difficulties that are encountered when attempting to complete the life cycle inventory and increase the reliability and transparency of results. In this paper, which was developed in the context of the research project IEA EBC Annex 72, we demonstrate the implications of taking such approach and describe the results of a comparison among different national standards/guidelines that are used to conduct LCA for building decomposition. Methods: We initially identified the main characteristics of the standards/guidelines used by Annex participant countries. The “be2226” reference office building was used as a reference to apply the different national standards/guidelines related to building decomposition. It served as a basis of comparison, allowing us to identify the implications of using different systems/standards in the LCA practice, in terms of how these differences affect the LCI structures, LCA databases and the methods used to communicate results. We also analyzed the implications of integrating these standards/guidelines into Building Information Modelling (BIM) to support LCA. Results: Twelve national classification systems/ standards/guidelines for the building decomposition were compared. Differences were identified among the levels of decomposition and grouping principles, as well as the consequences of these differences that were related to the LCI organization. In addition, differences were observed among the LCA databases and the structures of the results. Conclusions: The findings of this study summarize and provide an overview of the most relevant aspects of using a standardized building decomposition structure to conduct LCA. Recommendations are formulated on the basis of these findings.
|
|
11. |
|
|
12. |
|
|
13. |
|
|
14. |
- Baiocchi, B., et al.
(författare)
-
Discriminating the role of rotation and its gradient in determining ion stiffness mitigation in JET
- 2013
-
Ingår i: Plasma Physics and Controlled Fusion. - : IOP Publishing. - 0741-3335 .- 1361-6587. ; 55:2, s. 025010-
-
Tidskriftsartikel (refereegranskat)abstract
- Starting from recent JET experimental results that show a significant reduction of ion stiffness in the plasma core region due to plasma rotation in the presence of low magnetic shear, an experiment was carried out at JET in order to separate the role of rotation and rotation gradient in mitigating the ion stiffness level. Enhanced toroidal field ripple (up to 1.5%) and external resonant magnetic fields are the two mechanisms used to try and decouple the rotation value from its gradient. In addition, shots with reversed toroidal field and plasma current, yielding counter-current neutral beam injection, were compared with standard co-injection cases. These tools also allowed varying the rotation independently of the injected power. Shots with high rotation gradient are found to maintain their low stiffness level even when the absolute value of the rotation was significantly reduced. Conversely, high but flat rotation yields much less peaked ion temperature profiles than a peaked rotation profile with lower values. This behaviour suggests the rotation gradient as the main player in reducing the ion stiffness level. In addition, it is found that inverting the rotation gradient sign does not suppress its effect on ion stiffness.
|
|
15. |
|
|
16. |
- Baiocchi, B., et al.
(författare)
-
Transport analysis and modelling of the evolution of hollow density profiles plasmas in JET and implication for ITER
- 2015
-
Ingår i: Nuclear Fusion. - : IOP PUBLISHING LTD. - 0029-5515 .- 1741-4326. ; 55:12
-
Tidskriftsartikel (refereegranskat)abstract
- The density evolution during the transient phase just after the L-H transition is investigated using theoretical transport models. Cases characterized by core densities which evolve in longer timescales than the edge densities, leading to hollow density profiles (R/L-n = -R del n/n < 0) are modelled. This density evolution is particularly interesting because it has been shown to be beneficial in the view of the access to burning plasma conditions in ITER (Loarte et al 2013 Nucl. Fusion 53 083031). Self-consistent simulations of the JET discharge 79676 of the density-only, and of the density and the temperatures are carried out using a quasilinear gyrokinetic code, QuaLiKiz (Bourdelle et al 2007 Phys. Plasmas 14 112501), coupled with a transport code CRONOS (Artaud et al 2010 Nucl. Fusion 50 043001). The slow evolution of the hollow density, associated with the self-consistently calculated hollow NBI particle deposition, is well reproduced in the plasma core. Indeed, QuaLiKiz is shown to reproduce nonlinear gyrokinetic heat and particle fluxes well for both positive and negative R/L-n. That gives a theoretical and general basis for the persistence of the hollowness, laying the groundwork for the extrapolation to ITER.
|
|
17. |
- Baiocchi, B., et al.
(författare)
-
Turbulent transport analysis of JET H-mode and hybrid plasmas using QuaLiKiz and Trapped Gyro Landau Fluid
- 2015
-
Ingår i: Plasma Physics and Controlled Fusion. - : IOP Publishing. - 0741-3335 .- 1361-6587. ; 57:3
-
Tidskriftsartikel (refereegranskat)abstract
- The physical transport processes at the basis of JET typical inductive H-mode scenarios and advanced hybrid regimes, with improved thermal confinement, are analyzed by means of some of the newest and more sophisticated quasi-linear transport models: trapped gyro Landau fluid (TGLF) and QuaLiKiz. The temporal evolution of JET pulses is modelled by CRONOS where the turbulent transport is modelled by either QuaLiKiz or TGLF. Both are first principle models with a more comprehensive physics than the models previously developed and therefore allow the analysis of the physics at the basis of the investigated scenarios. For H-modes, ion temperature gradient (ITG) modes are found to be dominant and the transport models are able to properly reproduce temperature profiles in self-consistent simulations. However, for hybrid regimes, in addition to ITG trapped electron modes (TEM) are also found to be important and different physical mechanisms for turbulence reduction play a decisive role. Whereas E x B flow shear and plasma geometry have a limited impact on turbulence, the presence of a large population of fast ions, quite important in low density regimes, can stabilize core turbulence mainly when the electromagnetic effects are taken into account. The TGLF transport model properly captures these mechanisms and correctly reproduces temperatures.
|
|
18. |
- Casiraghi, I, et al.
(författare)
-
Core integrated simulations for the Divertor Tokamak Test facility scenarios towards consistent core-pedestal-SOL modelling
- 2023
-
Ingår i: Plasma Physics and Controlled Fusion. - : IOP Publishing. - 0741-3335 .- 1361-6587. ; 65:3, s. 035017-
-
Tidskriftsartikel (refereegranskat)abstract
- Deuterium plasma discharges of the Divertor Tokamak Test facility (DTT) in different operational scenarios have been predicted by a comprehensive first-principle based integrated modelling activity using state-of-art quasi-linear transport models. The results of this work refer to the updated DTT configuration, which includes a device size optimisation (enlargement to R-0=2.19 a = 0.70 m) and upgrades in the heating systems. The focus of this paper is on the core modelling, but special attention was paid to the consistency with the scrape-off layer parameters required to achieve divertor plasma detachment. The compatibility of these physics-based predicted scenarios with the electromagnetic coil system capabilities was then verified. In addition, first estimates of DTT sawteeth and of DTT edge localised modes were achieved.
|
|
19. |
- Casiraghi, I, et al.
(författare)
-
First principle-based multi-channel integrated modelling in support of the design of the Divertor Tokamak Test facility
- 2021
-
Ingår i: Nuclear Fusion. - : IOP Publishing Ltd. - 0029-5515 .- 1741-4326. ; 61:11
-
Tidskriftsartikel (refereegranskat)abstract
- An intensive integrated modelling work of the main scenarios of the new Divertor Tokamak Test (DTT) facility with a single null divertor configuration has been performed using first principle quasi-linear transport models, in support of the design of the device and of the definition of its scientific work programme. First results of this integrated modelling work on DTT (R (0) = 2.14 m, a = 0.65 m) are presented here along with outcome of the gyrokinetic simulations used to validate the reduced models in the DTT range of parameters. As a result of this work, the heating mix has been defined, the size of device has been increased to R (0) = 2.19 m and a = 0.70 m, the use of pellets for fuelling has been recommended and reference profiles for diagnostic design, estimates of neutron yields and fast particle losses have been made available.
|
|
20. |
|
|
21. |
|
|
22. |
- Casiraghi, I, et al.
(författare)
-
Scenario modelling for the Divertor Tokamak Test facility
- 2022
-
Ingår i: NUOVO CIMENTO C-COLLOQUIA AND COMMUNICATIONS IN PHYSICS. - : SOC ITALIANA FISICA. - 2037-4909. ; 45:6
-
Tidskriftsartikel (refereegranskat)abstract
- The scenario integrated modelling is a top priority work during the design of a new tokamak, as the Divertor Tokamak Test facility (DTT) under construction at the ENEA Research Center in Frascati. The first simulations of the main baseline scenarios contributed to the optimization of the DTT project, particularly with regard to the machine size and heating systems, besides serving as reference for diagnostics design. In this paper we report the first simulations of the full power baseline scenario in the final configuration of the machine and heating mix.
|
|
23. |
|
|
24. |
|
|
25. |
- Di Saverio, Salomone, et al.
(författare)
-
Diagnosis and treatment of acute appendicitis: 2020 update of the WSES Jerusalem guidelines
- 2020
-
Ingår i: World Journal of Emergency Surgery. - : BMC. - 1749-7922. ; 15:1
-
Forskningsöversikt (refereegranskat)abstract
- Background and aims Acute appendicitis (AA) is among the most common causes of acute abdominal pain. Diagnosis of AA is still challenging and some controversies on its management are still present among different settings and practice patterns worldwide. In July 2015, the World Society of Emergency Surgery (WSES) organized in Jerusalem the first consensus conference on the diagnosis and treatment of AA in adult patients with the intention of producing evidence-based guidelines. An updated consensus conference took place in Nijemegen in June 2019 and the guidelines have now been updated in order to provide evidence-based statements and recommendations in keeping with varying clinical practice: use of clinical scores and imaging in diagnosing AA, indications and timing for surgery, use of non-operative management and antibiotics, laparoscopy and surgical techniques, intra-operative scoring, and peri-operative antibiotic therapy. Methods This executive manuscript summarizes the WSES guidelines for the diagnosis and treatment of AA. Literature search has been updated up to 2019 and statements and recommendations have been developed according to the GRADE methodology. The statements were voted, eventually modified, and finally approved by the participants to the consensus conference and by the board of co-authors, using a Delphi methodology for voting whenever there was controversy on a statement or a recommendation. Several tables highlighting the research topics and questions, search syntaxes, and the statements and the WSES evidence-based recommendations are provided. Finally, two different practical clinical algorithms are provided in the form of a flow chart for both adults and pediatric (< 16 years old) patients. Conclusions The 2020 WSES guidelines on AA aim to provide updated evidence-based statements and recommendations on each of the following topics: (1) diagnosis, (2) non-operative management for uncomplicated AA, (3) timing of appendectomy and in-hospital delay, (4) surgical treatment, (5) intra-operative grading of AA, (6) ,management of perforated AA with phlegmon or abscess, and (7) peri-operative antibiotic therapy.
|
|
26. |
- Mantica, P., et al.
(författare)
-
A Key to Improved Ion Core Confinement in the JET Tokamak : Ion Stiffness Mitigation due to Combined Plasma Rotation and Low Magnetic Shear
- 2011
-
Ingår i: Physical Review Letters. - 0031-9007 .- 1079-7114. ; 107:13, s. 135004-
-
Tidskriftsartikel (refereegranskat)abstract
- New transport experiments on JET indicate that ion stiffness mitigation in the core of a rotating plasma, as described by Mantica et al. [Phys. Rev. Lett. 102, 175002 (2009)] results from the combined effect of high rotational shear and low magnetic shear. The observations have important implications for the understanding of improved ion core confinement in advanced tokamak scenarios. Simulations using quasilinear fluid and gyrofluid models show features of stiffness mitigation, while nonlinear gyrokinetic simulations do not. The JET experiments indicate that advanced tokamak scenarios in future devices will require sufficient rotational shear and the capability of q profile manipulation.
|
|
27. |
- Mantica, P., et al.
(författare)
-
Ion heat transport studies in JET
- 2011
-
Ingår i: Plasma Physics and Controlled Fusion. - : IOP Publishing. - 1361-6587 .- 0741-3335. ; 53:12
-
Tidskriftsartikel (refereegranskat)abstract
- Detailed experimental studies of ion heat transport have been carried out in JET exploiting the upgrade of active charge exchange spectroscopy and the availability of multi-frequency ion cyclotron resonance heating with (3)He minority. The determination of ion temperature gradient (ITG) threshold and ion stiffness offers unique opportunities for validation of the well-established theory of ITG driven modes. Ion stiffness is observed to decrease strongly in the presence of toroidal rotation when the magnetic shear is sufficiently low. This effect is dominant with respect to the well-known omega(ExB) threshold up-shift and plays a major role in enhancing core confinement in hybrid regimes and ion internal transport barriers. The effects of T(e)/T(i) and s/q on ion threshold are found rather weak in the domain explored. Quasi-linear fluid/gyro-fluid and linear/non-linear gyro-kinetic simulations have been carried out. Whilst threshold predictions show good match with experimental observations, some significant discrepancies are found on the stiffness behaviour.
|
|
28. |
- Mantica, P, et al.
(författare)
-
Key to Improved Ion Core Confinement in the JET Tokamak : Ion Stiffness Mitigation due to Combined Plasma Rotation and Low Magnetic Shear
- 2010
-
Konferensbidrag (övrigt vetenskapligt/konstnärligt)abstract
- New experimental evidence indicates that ion stiffness mitigation in the core of rotating plasmas, observed previously in JET, results from the combined effect of high rotational shear and low magnetic shear. Ionstiffness in the outer plasma region is found to remain very high irrespective of rotation. Dedicated experimentsin plasmas with different q profiles and rotation levels point to a larger effect of rotation in reducing stiffnesswhen the core q profile is made flatter. The results have implications for the understanding of improved ion coreconfinement in hybrid plasmas or Internal Transport Barriers, both characterized by high rotation and low magnetic shear. Experimental evidence in these scenarios is discussed. Simulations indicate that the physics behindthese results may lie in the ITG/TEM turbulence behavior at the transition between fully developed turbulenceand zonal flows quenching. These findings point to the need for future devices of achieving sufficient rotationalshear and capability of q profile manipulation to reach improved ion core confinement, which is an essentialfeature of Advanced Tokamak operation.
|
|
29. |
|
|
30. |
|
|