| 1. |
- Martel, I., et al.
(författare)
-
An innovative Superconducting Recoil Separator for HIE-ISOLDE
- 2023
-
Ingår i: Nuclear Instruments and Methods in Physics Research, Section B: Beam Interactions with Materials and Atoms. - : ELSEVIER. - 0168-583X .- 1872-9584. ; 541, s. 176-179
-
Tidskriftsartikel (refereegranskat)abstract
- The ISOLDE Scientific Infrastructure at CERN offers a unique range of post-accelerated radioactive beams. The scientific program can be improved with the “Isolde Superconducting Recoil Separator” (ISRS), an innovative spectrometer able to deliver unprecedented (A, Z) resolution. In this paper we present an overview of the physics and ongoing technical developments.
|
|
| 2. |
- Rossi, L., et al.
(författare)
-
A European Collaboration to Investigate Superconducting Magnets for Next Generation Heavy Ion Therapy
- 2022
-
Ingår i: IEEE transactions on applied superconductivity (Print). - : Institute of Electrical and Electronics Engineers (IEEE). - 1051-8223 .- 1558-2515. ; 32:4
-
Tidskriftsartikel (refereegranskat)abstract
- Next generation ion therapy magnets both for gantry and for accelerator (synchrotron) are under investigation in a recently launched European collaboration that, in the frame of the European H2020 HITRIplus and I.FAST programmes, has obtained some funding for work packages on superconducting magnets. Design and technology of superconducting magnets will be developed for ion therapy synchrotron and -especially- gantry, taking as reference beams of 430 MeV/nucleon ions (C-ions) with 10(10) ions/pulse. The magnets are about 60-90 mm diameter, 4 to 5 T peak field with a field change of about 0.3 T/s and good field quality. The paper will illustrate the organization of the collaboration and the technical program. Various superconductor options (LTS, MgB2 or HTS) and different magnet shapes, like classical CosTheta or innovative Canted CosTheta (CCT), with curved multifunction (dipole and quadrupole), are under evaluation, CCT being the baseline. These studies should provide design inputs for a new superconducting gantry design for existing facilities and, on a longer time scale, for a brand-new hadron therapy centre to be placed in the South East Europe (SEEIIST project).
|
|
| 3. |
|
|
| 4. |
- Bagni, Tommaso, et al.
(författare)
-
Investigating the effect of rolling deformation on the electro-mechanical limits of Nb3Sn wires produced by RRP® and PIT technologies
- 2024
-
Ingår i: Superconductors Science and Technology. - : Institute of Physics (IOP). - 0953-2048 .- 1361-6668. ; 37:9
-
Tidskriftsartikel (refereegranskat)abstract
- Future high-field magnets for particle accelerators hinge on the crucial development of advanced Nb3Sn wires engineered to withstand the large stresses generated during magnet assembly and operation. The superconducting properties of Nb3Sn enable the design of compact accelerator-quality magnets above 10 T, but at the same time the brittleness and strain sensitivity of the material impose careful consideration of the mechanical limits. In addition, accelerator magnets are wound using Rutherford cables and the cabling process generates deformations in the wire that can affect its electro-mechanical performance. This paper reports on the impact of the rolling deformation on the transverse stress tolerance of high-performance restacked-rod-process (RRP (R)) and powder-in-tube (PIT) Nb3Sn wires. Rolling deformation was used to mimic the effect of cabling on the wire shape. Deformed samples were compared to reference round wires in term of stress dependence and irreversible limit (sigma(irr)) of the critical current (I-c) under transverse compressive loads up to 240 MPa. Experiments were performed at 4.2 K, 19 T, on resin-impregnated single wires that imitate the operating conditions in a Rutherford cable of an accelerator magnet. The results show that rolling deformation has a detrimental effect on the initial I-c of PIT wires, but it does not influence the behavior of the wire under stresses above 70 MPa. On the other hand, the deformation of RRP (R) wires leads to an improved sigma(irr) without affecting the initial I-c. Additionally, a 2D-mechanical finite element method model of the RRP (R) wire was developed to investigate the impact of the wire geometry on the plastic deformation of the copper matrix, which induces residual stresses on Nb3Sn and is the main cause for the permanent reduction of I-c. Based on the model results, an alternative layout of the wire was proposed that improves its stress tolerance without affecting its electrical transport properties.
|
|
| 5. |
|
|
| 6. |
- Lonardo, F., et al.
(författare)
-
Influence of the Heat Treatment on the Layer JC of Internal-Sn Nb3Sn Wires With Internally Oxidized Nanoparticles
- 2024
-
Ingår i: IEEE transactions on applied superconductivity (Print). - : Institute of Electrical and Electronics Engineers (IEEE). - 1051-8223 .- 1558-2515. ; 34:5
-
Tidskriftsartikel (refereegranskat)abstract
- We evaluated various heat treatments (HT) for maximizing the Nb 3 Sn layer thickness while retaining a refined grain microstructure in low filament count internal-Sn Nb 3 Sn Rod-In-Tube wires with internally oxidized nanoparticles. These wires were manufactured in our laboratory using SnO 2 as oxygen source and Nb alloys containing Ta and Zr or Hf. By reacting the wires at 650 °C for 200 hours we obtained relatively thin reaction layers but high layer critical current densities (layer J C ) of ∼3000 A/mm 2 for Hf-containing wires and ∼2700 A/mm 2 for Zr-containing wires, both at 4.2 K and 16 T. Notably, both of these values are over the layer J C threshold of 2500 A/mm 2 , which is estimated to be necessary for attaining the corresponding Future Circular Collider (FCC) target non-Cu J C of 1500 A/mm 2 . Following this heat treatment, the fine-grained Nb 3 Sn area occupies only ∼35% of the filament area for Hf-containing wires and ∼20% for Zr-containing wires. After heat treatments with a reaction step at 700 °C these values increase to 70–80% and ∼60%, respectively, with only a minor increase of the grain size. However, we observed a noticeable decrease in the layer J C for these HT. Magnetic measurements show that the high J C wires exhibit a point defect contribution from precipitates to the pinning force, which is missing in wires with depressed J C values. The higher heat treatment temperatures may have caused excessive coarsening of the oxide precipitates, to sizes unsuitable for flux pinning. Reaction heat treatment temperatures in the range of 650 °C to 700 °C and durations between 50 and 200 hours may provide a better compromise between the Nb 3 Sn layer thickness, its grain size and nanoparticle size.
|
|
| 7. |
|
|
| 8. |
|
|
