| 1. |
- Akram, Nadeem, 1980-, et al.
(författare)
-
Transmission of slow highly charged ions through ultra-thin carbon nano-sheets
- 2011
-
Ingår i: Proceedings of 3<sup>rd</sup> Int. Conf. on “Current developments in Atomic, Molecular, Optical and Nano Physics”.
-
Konferensbidrag (refereegranskat)abstract
- Transmission properties of slow highly charged ions through nanometer thick foils are discussed. We also report on the measurement of the energy loss and the charge states of 46.2 keV Ne10+-ions and 11.7 keV Ne3+-ions transmitted through ultra-thin carbon nano-sheets. The sheets had a thickness of 1.2 nm (single molecular layer) and 3.6 nm (three molecular layers). The measured energy loss of the transmitted ions is considerably smaller than the calculated energy loss by SRIM but it is in agreement with energy loss calculated using the Firsov model. The majority of the transmitted ions retain their initial charge state (up to 98%) contrary to prediction by the classical over-the-barrier model. The results suggest that the energy loss of slow highly charged ions in such thin sheets is only due to the electronic excitations, without charge exchange inside the target.
|
|
| 2. |
- Backes, Claudia, et al.
(författare)
-
Production and processing of graphene and related materials
- 2020
-
Ingår i: 2D Materials. - : IOP Publishing. - 2053-1583. ; 7:2
-
Tidskriftsartikel (refereegranskat)abstract
- We present an overview of the main techniques for production and processing of graphene and related materials (GRMs), as well as the key characterization procedures. We adopt a 'hands-on' approach, providing practical details and procedures as derived from literature as well as from the authors' experience, in order to enable the reader to reproduce the results. Section I is devoted to 'bottom up' approaches, whereby individual constituents are pieced together into more complex structures. We consider graphene nanoribbons (GNRs) produced either by solution processing or by on-surface synthesis in ultra high vacuum (UHV), as well carbon nanomembranes (CNM). Production of a variety of GNRs with tailored band gaps and edge shapes is now possible. CNMs can be tuned in terms of porosity, crystallinity and electronic behaviour. Section II covers 'top down' techniques. These rely on breaking down of a layered precursor, in the graphene case usually natural crystals like graphite or artificially synthesized materials, such as highly oriented pyrolythic graphite, monolayers or few layers (FL) flakes. The main focus of this section is on various exfoliation techniques in a liquid media, either intercalation or liquid phase exfoliation (LPE). The choice of precursor, exfoliation method, medium as well as the control of parameters such as time or temperature are crucial. A definite choice of parameters and conditions yields a particular material with specific properties that makes it more suitable for a targeted application. We cover protocols for the graphitic precursors to graphene oxide (GO). This is an important material for a range of applications in biomedicine, energy storage, nanocomposites, etc. Hummers' and modified Hummers' methods are used to make GO that subsequently can be reduced to obtain reduced graphene oxide (RGO) with a variety of strategies. GO flakes are also employed to prepare three-dimensional (3d) low density structures, such as sponges, foams, hydro- or aerogels. The assembly of flakes into 3d structures can provide improved mechanical properties. Aerogels with a highly open structure, with interconnected hierarchical pores, can enhance the accessibility to the whole surface area, as relevant for a number of applications, such as energy storage. The main recipes to yield graphite intercalation compounds (GICs) are also discussed. GICs are suitable precursors for covalent functionalization of graphene, but can also be used for the synthesis of uncharged graphene in solution. Degradation of the molecules intercalated in GICs can be triggered by high temperature treatment or microwave irradiation, creating a gas pressure surge in graphite and exfoliation. Electrochemical exfoliation by applying a voltage in an electrolyte to a graphite electrode can be tuned by varying precursors, electrolytes and potential. Graphite electrodes can be either negatively or positively intercalated to obtain GICs that are subsequently exfoliated. We also discuss the materials that can be amenable to exfoliation, by employing a theoretical data-mining approach. The exfoliation of LMs usually results in a heterogeneous dispersion of flakes with different lateral size and thickness. This is a critical bottleneck for applications, and hinders the full exploitation of GRMs produced by solution processing. The establishment of procedures to control the morphological properties of exfoliated GRMs, which also need to be industrially scalable, is one of the key needs. Section III deals with the processing of flakes. (Ultra)centrifugation techniques have thus far been the most investigated to sort GRMs following ultrasonication, shear mixing, ball milling, microfluidization, and wet-jet milling. It allows sorting by size and thickness. Inks formulated from GRM dispersions can be printed using a number of processes, from inkjet to screen printing. Each technique has specific rheological requirements, as well as geometrical constraints. The solvent choice is critical, not only for the GRM stability, but also in terms of optimizing printing on different substrates, such as glass, Si, plastic, paper, etc, all with different surface energies. Chemical modifications of such substrates is also a key step. Sections IV-VII are devoted to the growth of GRMs on various substrates and their processing after growth to place them on the surface of choice for specific applications. The substrate for graphene growth is a key determinant of the nature and quality of the resultant film. The lattice mismatch between graphene and substrate influences the resulting crystallinity. Growth on insulators, such as SiO2, typically results in films with small crystallites, whereas growth on the close-packed surfaces of metals yields highly crystalline films. Section IV outlines the growth of graphene on SiC substrates. This satisfies the requirements for electronic applications, with well-defined graphene-substrate interface, low trapped impurities and no need for transfer. It also allows graphene structures and devices to be measured directly on the growth substrate. The flatness of the substrate results in graphene with minimal strain and ripples on large areas, allowing spectroscopies and surface science to be performed. We also discuss the surface engineering by intercalation of the resulting graphene, its integration with Si-wafers and the production of nanostructures with the desired shape, with no need for patterning. Section V deals with chemical vapour deposition (CVD) onto various transition metals and on insulators. Growth on Ni results in graphitized polycrystalline films. While the thickness of these films can be optimized by controlling the deposition parameters, such as the type of hydrocarbon precursor and temperature, it is difficult to attain single layer graphene (SLG) across large areas, owing to the simultaneous nucleation/growth and solution/precipitation mechanisms. The differing characteristics of polycrystalline Ni films facilitate the growth of graphitic layers at different rates, resulting in regions with differing numbers of graphitic layers. High-quality films can be grown on Cu. Cu is available in a variety of shapes and forms, such as foils, bulks, foams, thin films on other materials and powders, making it attractive for industrial production of large area graphene films. The push to use CVD graphene in applications has also triggered a research line for the direct growth on insulators. The quality of the resulting films is lower than possible to date on metals, but enough, in terms of transmittance and resistivity, for many applications as described in section V. Transfer technologies are the focus of section VI. CVD synthesis of graphene on metals and bottom up molecular approaches require SLG to be transferred to the final target substrates. To have technological impact, the advances in production of high-quality large-area CVD graphene must be commensurate with those on transfer and placement on the final substrates. This is a prerequisite for most applications, such as touch panels, anticorrosion coatings, transparent electrodes and gas sensors etc. New strategies have improved the transferred graphene quality, making CVD graphene a feasible option for CMOS foundries. Methods based on complete etching of the metal substrate in suitable etchants, typically iron chloride, ammonium persulfate, or hydrogen chloride although reliable, are time- and resource-consuming, with damage to graphene and production of metal and etchant residues. Electrochemical delamination in a low-concentration aqueous solution is an alternative. In this case metallic substrates can be reused. Dry transfer is less detrimental for the SLG quality, enabling a deterministic transfer. There is a large range of layered materials (LMs) beyond graphite. Only few of them have been already exfoliated and fully characterized. Section VII deals with the growth of some of these materials. Amongst them, h-BN, transition metal tri- and di-chalcogenides are of paramount importance. The growth of h-BN is at present considered essential for the development of graphene in (opto) electronic applications, as h-BN is ideal as capping layer or substrate. The interesting optical and electronic properties of TMDs also require the development of scalable methods for their production. Large scale growth using chemical/physical vapour deposition or thermal assisted conversion has been thus far limited to a small set, such as h-BN or some TMDs. Heterostructures could also be directly grown. Section VIII discusses advances in GRM functionalization. A broad range of organic molecules can be anchored to the sp(2) basal plane by reductive functionalization. Negatively charged graphene can be prepared in liquid phase (e.g. via intercalation chemistry or electrochemically) and can react with electrophiles. This can be achieved both in dispersion or on substrate. The functional groups of GO can be further derivatized. Graphene can also be noncovalently functionalized, in particular with polycyclic aromatic hydrocarbons that assemble on the sp(2) carbon network by pi-pi stacking. In the liquid phase, this can enhance the colloidal stability of SLG/FLG. Approaches to achieve noncovalent on-substrate functionalization are also discussed, which can chemically dope graphene. Research efforts to derivatize CNMs are also summarized, as well as novel routes to selectively address defect sites. In dispersion, edges are the most dominant defects and can be covalently modified. This enhances colloidal stability without modifying the graphene basal plane. Basal plane point defects can also be modified, passivated and healed in ultra-high vacuum. The decoration of graphene with metal nanoparticles (NPs) has also received considerable attention, as it allows to exploit synergistic effects between NPs and graphene. Decoration can be either achieved chemically or in the gas phase. All LMs,
|
|
| 3. |
- Brueckner, Frank, et al.
(författare)
-
Enhanced manufacturing possibilities using multi-materials in laser metal deposition
- 2018
-
Ingår i: Journal of laser applications. - : American Institute of Physics (AIP). - 1042-346X .- 1938-1387. ; 26:2, s. 10-12
-
Tidskriftsartikel (refereegranskat)abstract
- Additive manufacturing (AM) addresses various benefits as the buildup of complex shaped parts, the possibility of functional integration, reduced lead times or the use of difficult machinable materials compared to conventional manufacturing possibilities. Beside these advantages, the use of more than one material in a component would strongly increase the field of applications in typical AM branches as energy, aerospace, or medical technology. By means of multi-material buildups, cost-intensive alloys could be only used in high-loaded areas of the part, whereas the remaining part could be fabricated with cheaper compositions. The selection of combined materials strongly depends on the requested thermophysical but also mechanical properties. Within this contribution, examples (e.g., used in the turbine business) show how alloys can be arranged to fit together, e.g., in terms of a well-chosen coefficient of thermal expansion. As can be seen in nature, the multi-material usage can be characterized by sharp intersections from one material to the other (e.g., in case of a thin corrosion protection), but also by graded structures enabling a smoother material transition (e.g., in case of dissimilar materials which are joined together without defects). The latter is shown for an example from aerospace within this paper. Another possibility is the simultaneous placement of several materials, e.g., hard carbide particles placed in a more ductile matrix composition. These particles can be varied in size (e.g., TiC versus WC). Also the ratio between carbides and matrix alloy can be adjusted depending on its application. Especially, nozzle-based free form fabrication technologies, e.g., laser metal deposition, enable the utilization of more than one material. Within this contribution, possibilities to feed more than one filler material are demonstrated. In addition, results of multi-material processes are shown. Finally, this work focuses on different (potential) applications, mainly on power generation, but also for medical technology or wear resistant components.
|
|
| 4. |
- Brueckner, Frank, et al.
(författare)
-
Fabrication of metallic multi-material components using Laser Metal Deposition
- 2017
-
Ingår i: Solid Freeform Fabrication 2017. - : The University of Texas at Austin. ; , s. 2530-2538
-
Konferensbidrag (övrigt vetenskapligt/konstnärligt)abstract
- Meanwhile, Laser Metal Deposition (LMD) is a well-known Additive Manufacturing technology used in various industrial branches as energy, tooling or aerospace. It can be used for the fabrication of new components but also repair applications. So far, volume build-ups were mostly carried out with one single material only. However, loading conditions may strongly vary and, hence, the use of more than one material in a component would yield major benefits. By means of multi-material build-ups, cost-intensive alloys could be used in highly-loaded areas of the part, whereas the remaining part could be fabricated with cheaper compositions. The selection of combined materials strongly depends on the requested thermo-physical and mechanical properties. Within this contribution, possibilities of material combinations by LMD and selected examples of beneficial multi-material use are presented.
|
|
| 5. |
- Eberle, Sebastian, et al.
(författare)
-
Additive manufacturing of an AlSi40 mirror coated with electroless nickel for cryogenic space applications
- 2018
-
Ingår i: International Conference on Space Optics—ICSO 2018. - : SPIE - International Society for Optical Engineering.
-
Konferensbidrag (refereegranskat)abstract
- Advanced Manufacturing (AM) has the potential to improve existing technologies and applications in terms of performance, light-weighting and costs. In the context of the SME4ALM initiative, launched by DLR and ESA, the company Kampf Telescope Optics GmbH (KTO) in cooperation with the Fraunhofer Institute for Material and Beam Technology (IWS) have assessed the feasibility of AM to build a high-performance optical mirror for space applications. For the assessment of the AM potentials, a mirror design concept for cryogenic instruments for observations in the IR and NIR range was baselined. In a second step, Nickel-Phosphorus (NiP) was selected as optical coating. The combination of coating and mirror material is a primary design driver for optical performance. Both materials must have a very similar CTE as well as be compliant to modern optical manufacturing (diamond turning, polishing). As a promising candidate for NiP coating the AlSi40 was selected for the mirror structure. The potential advantages of AM for optical mirrors in terms of mechanical performance, cost, and manufacturing time were exploited. The achievement of those objectives was / will be demonstrated by:1. verifying AM material properties and manufacturability of AM mirrors by material sample tests and subcomponent tests2. designing AM mirror demonstrator by structural, thermal, and optical performance analysis3. applying and elaborating AM specific design methods (topology optimization, sandwich structures with internal microstructures, monolithic design, etc.)4. manufacturing, assembling, and testing AM mirror demonstrator to verify manufacturability and optical performance5. comparing optical and mechanical performance of the AM mirror demonstrator to a conventional mirror by numerical analysis to exploit potential advantages of AM
|
|
| 6. |
- Lopez, Elena, et al.
(författare)
-
Evaluation of 3D-printed parts by means of high-performance computer tomography
- 2018
-
Ingår i: Journal of laser applications. - : American Institute of Physics (AIP). - 1042-346X .- 1938-1387. ; 30:3
-
Tidskriftsartikel (refereegranskat)abstract
- Conventional tactile and optical testing methods are not capable to detect complex inner geometries or complex surface shapes. Detecting porosities in parts is also not possible with those nondestructive methods. Among other material parameters, geometrical accuracy is essential to determine part's quality. Additive manufacturing processes also have to be optimized regarding geometry deviations caused by distortion or unfavorable orientation in the build chamber. For additive manufactured parts that incorporate previously mentioned features, high-performance computer tomography is the more suitable nondestructive testing method. Components of different materials such as plastics, ceramics, composites, or metals can be completely characterized. This nondestructive testing method was used for porosity analysis regarding the shape and local distribution of pores in an additive manufactured part to find correlations concerning the most suitable process conditions. The measured part data were also compared to original CAD files to determine zones of deviation and apply specific process strategies to avoid distortion. This paper discusses the results of integrating high-performance computer tomography (power: 500 W, max. part size: Ø 300 mm, 300 × 430 mm2) in a productionlike environment of additively manufactured parts for a wide range of technologies (i.e., electron beam melting and selective laser melting). I. INTRODUCTION
|
|
| 7. |
- Mueller, Michael, et al.
(författare)
-
Microstructural, mechanical, and thermo-physical characterization of hypereutectic AlSi40 fabricated by selective laser melting
- 2019
-
Ingår i: Journal of laser applications. - : Laser Institute of America. - 1042-346X .- 1938-1387. ; 31:2
-
Tidskriftsartikel (refereegranskat)abstract
- The powder bed additive manufacturing process selective laser melting (SLM) enables designers and engineers to overcome restrictions of conventional manufacturing technologies. The potential of fabricating complex lightweight structures and processing advanced materials is a key feature for enhancing further development of high performance components for space applications. Due to a high specific stiffness and a thermal expansion coefficient very close to electroless nickel, which is an advantageous optical coating material, the hypereutectic aluminum-silicon alloy AlSi40 shows great potential for the manufacturing of optical mirrors for space applications. In prior investigations, Hilpert et al.showed the feasibility to process AlSi40 by SLM [E. Hilpert and S. Risse, Materials Science & Technology Conference and Exhibition MS&T'15, Columbus, Ohio, 4–8 October 2015(Association for Iron & Steel Technology, Warrendale, PA, 2015) and E. Hilpert, “Struktur und Eigenschaften von additiv gefertigten hypereutektischen Aluminum-Siliciumlegierungen,” in Werkstoffwoche 2017, Dresden, Germany, 28 September 2017 (Deutsche Gesellschaft für Materialkunde e.V., Berlin, 2017)]. Nevertheless, in order to qualify this material for space applications, the manufacturing process and fabricated samples need to be thoroughly investigated in terms of microstructural, mechanical, as well as thermo-physical characterization. The authors present results of the SLM process development for manufacturing dense AlSi40 samples with a relative density above 99.50%. The effect of various process parameters, such as hatch distance, preheating, and scanning strategy, on the formation of defects was investigated by destructive [e.g., optical microscopy (OM)] and nondestructive (e.g., computed tomography) testing. In addition, the effect of several thermal post-treatments on the AlSi40 microstructure was profoundly analyzed by multiple methods such as OM, scanning electron microscopy, and energy dispersive x-ray spectroscopy analysis. Moreover, mechanical and thermo-physical testing of manufactured specimens was conducted to provide material characteristics for component design. In conclusion, the determined material properties of AlSi40 samples fabricated by SLM were compared to bulk material properties. The gained knowledge and testing data were evaluated in order to identify correlations and dependencies.
|
|
| 8. |
- Seidel, André, et al.
(författare)
-
Added value by hybrid additive manufacturing and advanced manufacturing approaches
- 2018
-
Ingår i: Journal of laser applications. - : American Institute of Physics (AIP). - 1042-346X .- 1938-1387. ; 26:2, s. 6-8
-
Tidskriftsartikel (refereegranskat)abstract
- In order to lead to a competitive advantage, there is the need to carefully consider the pros and cons of state-of-the-art manufacturing techniques. This is frequently carried out in a competitive manner, but can also be done in a complementary way. This complementary approach is often used for the processing of difficult-to-machine materials with particular regard to high-tech parts or components. Hybrid machining processes or, more general, advanced machining processes can be brought to the point that the results would not be possible with the individual constituent processes in isolation [Hybrid Machining Processes Perspectives on Machining and Finishing (Springer International Publishing AG, 2016)]. Hence, the controlled interaction of process mechanisms and/or energy sources is frequently applied for a significant increase of the process performance [Advanced Machining Processes of Metallic Materials: Theory, Modelling, and Applications, 2nd ed. (2016)] and will be addressed within the present paper. A via electron beam melting manufactured gamma titanium aluminide nozzle is extended and adapted. This is done via hybrid laser metal deposition. The presented approach considers critical impacts like processing temperatures, temperature gradients, and solidification conditions with particular regard to crucial material properties like the phenomena of lamellar interface cracking [Laser-Based Manufacturing of Components using Materials with High Cracking Susceptibility (Laser Institute of America–LIA), pp. 586–592; Ti-2015: The 13th World Conference on Titanium, Symposium 5]. Furthermore, selected destructive and non-destructive testing is performed in order to prove the material properties. Finally, the results will be evaluated. This will also be done in the perspective of other applications.
|
|
