| 1. |
- Alsved, M., et al.
(författare)
-
Temperature-controlled airflow ventilation in operating rooms compared with laminar airflow and turbulent mixed airflow
- 2018
-
Ingår i: Journal of Hospital Infection. - : W B SAUNDERS CO LTD. - 0195-6701 .- 1532-2939. ; 98:2, s. 181-190
-
Tidskriftsartikel (refereegranskat)abstract
- Aim: To evaluate three types of ventilation systems for operating rooms with respect to air cleanliness [in colony-forming units (cfu/m(3))], energy consumption and comfort of working environment (noise and draught) as reported by surgical team members. Methods: Two commonly used ventilation systems, vertical laminar airflow (LAF) and turbulent mixed airflow (TMA), were compared with a newly developed ventilation technique, temperature-controlled airflow (T(c)AF). The cfu concentrations were measured at three locations in an operating room during 45 orthopaedic procedures: close to the wound (<40 cm), at the instrument table and peripherally in the room. The operating team evaluated the comfort of the working environment by answering a questionnaire. Findings: LAF and T(c)AF, but not TMA, resulted in less than 10 cfu/m(3) at all measurement locations in the room during surgery. Median values of cfu/m(3) close to the wound (250 samples) were 0 for LAF, 1 for T(c)AF and 10 for TMA. Peripherally in the room, the cfu concentrations were lowest for T(c)AF. The cfu concentrations did not scale proportionally with airflow rates. Compared with LAF, the power consumption of T(c)AF was 28% lower and there was significantly less disturbance from noise and draught. Conclusion: T(c)AF and LAF remove bacteria more efficiently from the air than TMA, especially close to the wound and at the instrument table. Like LAF, the new T(c)AF ventilation system maintained very low levels of cfu in the air, but T(c)AF used substantially less energy and provided a more comfortable working environment than LAF. This enables energy savings with preserved air quality.
|
|
| 2. |
- Nordin, E. Z., et al.
(författare)
-
Secondary organic aerosol formation from idling gasoline passenger vehicle emissions investigated in a smog chamber
- 2013
-
Ingår i: Atmospheric Chemistry and Physics. - : Copernicus GmbH. - 1680-7316 .- 1680-7324. ; 13:12, s. 6101-6116
-
Tidskriftsartikel (refereegranskat)abstract
- Gasoline vehicles have recently been pointed out as potentially the main source of anthropogenic secondary organic aerosol (SOA) in megacities. However, there is a lack of laboratory studies to systematically investigate SOA formation in real-world exhaust. In this study, SOA formation from pure aromatic precursors, idling and cold start gasoline exhaust from three passenger vehicles (EURO2-EURO4) were investigated with photo-oxidation experiments in a 6 m(3) smog chamber. The experiments were carried out down to atmospherically relevant organic aerosol mass concentrations. The characterization instruments included a high-resolution aerosol mass spectrometer and a proton transfer mass spectrometer. It was found that gasoline exhaust readily forms SOA with a signature aerosol mass spectrum similar to the oxidized organic aerosol that commonly dominates the organic aerosol mass spectra downwind of urban areas. After a cumulative OH exposure of similar to 5 x 10(6) cm(-3) h, the formed SOA was 1-2 orders of magnitude higher than the primary OA emissions. The SOA mass spectrum from a relevant mixture of traditional light aromatic precursors gave f(43) (mass fraction at m/z = 43), approximately two times higher than to the gasoline SOA. However O:C and H:C ratios were similar for the two cases. Classical C-6-C-9 light aromatic precursors were responsible for up to 60% of the formed SOA, which is significantly higher than for diesel exhaust. Important candidates for additional precursors are higher-order aromatic compounds such as C-10 and C-11 light aromatics, naphthalene and methyl-naphthalenes. We conclude that approaches using only light aromatic precursors give an incomplete picture of the magnitude of SOA formation and the SOA composition from gasoline exhaust.
|
|
| 3. |
|
|
| 4. |
|
|
| 5. |
- Nordin, E. Z., et al.
(författare)
-
Secondary organic aerosol formation from gasoline passenger vehicle emissions investigated in a smog chamber
- 2012
-
Ingår i: Atmospheric Chemistry and Physics Discussions. - : Copernicus Publications. - 1680-7367 .- 1680-7375. ; 12:12, s. 31725-31765
-
Tidskriftsartikel (refereegranskat)abstract
- Gasoline vehicles have elevated emissions of volatile organic compounds during cold starts and idling and have recently been pointed out as potentially the main source of anthropogenic secondary organic aerosol (SOA) in megacities. However, there is a lack of laboratory studies to systematically investigate SOA formation in real-world exhaust. In this study, SOA formation from pure aromatic precursors, idling and cold start gasoline exhaust from one Euro II, one Euro III and one Euro IV passenger vehicles were investigated using photo-oxidation experiments in a 6 m3 smog chamber. The experiments were carried out at atmospherically relevant organic aerosol mass concentrations. The characterization methods included a high resolution aerosol mass spectrometer and a proton transfer mass spectrometer. It was found that gasoline exhaust readily forms SOA with a signature aerosol mass spectrum similar to the oxidized organic aerosol that commonly dominates the organic aerosol mass spectra downwind urban areas. After 4 h aging the formed SOA was 1–2 orders of magnitude higher than the Primary OA emissions. The SOA mass spectrum from a relevant mixture of traditional light aromatic precursors gave f43 (mass fraction at m/z = 4 3) approximately two times higher than to the gasoline SOA. However O : C and H : C ratios were similar for the two cases. Classical C6–C9 light aromatic precursors were responsible for up to 60% of the formed SOA, which is significantly higher than for diesel exhaust. Important candidates for additional precursors are higher order aromatic compounds such as C10, C11 light aromatics, naphthalene and methyl-naphthalenes.
|
|
| 6. |
|
|
| 7. |
|
|
| 8. |
- Berg, N O, et al.
(författare)
-
Bronchocarcinogenic Properties of Welding and Thermal Spraying Fumes Containing Chromium in the Rat
- 1987
-
Ingår i: American Journal of Industrial Medicine. - : Wiley. - 0271-3586 .- 1097-0274. ; 11, s. 39-54
-
Tidskriftsartikel (refereegranskat)abstract
- The possible bronchocarcinogenic effects of fumes released during the shielded metal arc welding of stainless steel and the thermal spraying of chromium oxide (Cr2O3) have been studied on the rat. The fume particles were shown to contain tri- and hexavalent chromium in soluble and low soluble forms; they were collected and implanted as pellets in the bronchi of groups of 100 rats by the method of Laskin et al. A negative control group of 100 rats was included, as well as positive controls receiving pellets containing benz(a)pyrene. The experiment was continued for 34 months; no differences of biological significance were noted between the growth rates, survival times, and terminal organ weights of the test and negative control groups. At autopsy, the macroscopic and microscopic appearance of the organs in the three groups, including the local reaction to the implanted pellet, were similar. No precancerous changes were observed at the implantation sites; one rat, who received a pellet containing welding fumes, showed squamous cell carcinoma remote from the implantation site and not associated with the bronchus. It had the appearance of a metastasis. All three benz(a)pyrene control rats developed cancer at the implantation site. The occupational health implications of these findings are discussed.
|
|
| 9. |
|
|
| 10. |
|
|
| 11. |
- Bohgard, Mats, et al.
(författare)
-
Designing work and technology on human terms
- 2009. - 1:1
-
Ingår i: Work and technology on human terms. - Stockholm : Prevent. - 9789173650588 ; , s. 9-18
-
Bokkapitel (populärvet., debatt m.m.)
|
|
| 12. |
|
|
| 13. |
- Isaxon, Christina, et al.
(författare)
-
Realistic indoor nano-aerosols for a human exposure facility
- 2013
-
Ingår i: Journal of Aerosol Science. - : Elsevier BV. - 0021-8502. ; 60, s. 55-66
-
Tidskriftsartikel (refereegranskat)abstract
- The aim of this study was to achieve realistic levels of two different types of aerosols commonly abundant in indoor environments in an experimental chamber intended for human exposure studies and aerosol characterization. The aerosols chosen were particles from candle lights (in particle number dominated by inorganic water soluble particles) and from ozone-terpene reactions (organic particles). The aerosol generation and characterization system consisted of a controlled air tight stainless steel 22 m(3) chamber, to which the generation set-ups were connected. No air could enter or leave the chamber except through a conditioning system by which temperature, relative humidity and air exchange rate could be controlled. Candle smoke aerosol was generated from ten candles burning in a 1.33 m(3) glass and stainless steel chamber. The aerosol was diluted by clean air from the conditioning system before entering the chamber. Terpene vapor was generated by passing pure nitrogen through a glass bottle containing limonene oil. Ozone was generated by a spark discharge using pure O-2, and was added to the ventilation air flow downstream the inlet for terpene vapors and upstream the inlet to the chamber. Both aerosols were characterized with respect to number and mass concentrations, size distribution and chemical composition. Particle number concentration in the size range 10-650 nm could be varied from <10 cm(-3) to more than 900,000 cm(-3) (for candle smoke) or to more than 30,000 cm(-3) (for particles formed in a 160 ppb terpene/40 ppb ozone mixture). Furthermore, the set-ups were evaluated by, for each source, repeating the generation at six three-hour long events. For both aerosols repeatable generations at pre-determined concentration levels, that were stable over time, could be achieved. The results show that realistic concentrations of aerosols from real-world environments could be reproduced in a well-controlled manner and that this set-up could be used both for aerosol characterization and for human exposures. (C) 2013 Elsevier Ltd. All rights reserved.
|
|
| 14. |
|
|
| 15. |
|
|
| 16. |
|
|
| 17. |
- Schneider, T, et al.
(författare)
-
'EUROPART'. Airborne particles in the indoor environment. A European interdisciplinary review of scientific evidence on associations between exposure to particles in buildings and health effects
- 2003
-
Ingår i: Indoor Air. - : Hindawi Limited. - 0905-6947. ; 13:1, s. 38-48
-
Tidskriftsartikel (refereegranskat)abstract
- The relevance of particle mass, surface area or number concentration as risk indicators for health effects in non-industrial buildings has been assessed by a European interdisciplinary group of researchers (called EUROPART) by reviewing papers identified in Medline, Toxline, and OSH. Studies dealing with dermal effects or cancer or specifically addressing environmental tobacco smoke, house dust-mite, cockroach or animal allergens, microorganisms and pesticides were excluded. A total of 70 papers were reviewed, and eight were identified for the final review: Five experimental studies involving mainly healthy subjects, two cross-sectional office studies and one longitudinal study among elderly on cardiovascular effects. From most studies, no definite conclusions could be drawn. Overall, the group concluded that there is inadequate scientific evidence that airborne, indoor particulate mass or number concentrations can be used as generally applicable risk indicators of health effects in non-industrial buildings and consequently that there is inadequate scientific evidence for establishing limit values or guidelines for particulate mass or number concentrations.
|
|
| 18. |
|
|
| 19. |
- Strand, M, et al.
(författare)
-
Laboratory and field test of a sampling method for characterization of combustion aerosols at high temperatures
- 2004
-
Ingår i: Aerosol Science and Technology. - : Informa UK Limited. - 1521-7388 .- 0278-6826. ; 38:8, s. 757-765
-
Tidskriftsartikel (refereegranskat)abstract
- The objective of this study was to design and experimentally examine a sampling method for high-temperature aerosols from biomass combustion, in which nucleation and condensation from fly ash forming vapors is controlled. The sampling method includes a high-temperature probe in which the hot gas is diluted and then cooled. Laboratory results from sampling a model aerosol with known concentrations of SiO2 particles and KCl vapor showed that when using a high dilution ratio, the KCl vapor was effectively separated from the aerosol by deposition onto the probe walls. When a lower dilution ratio was used, the KCl vapor generated a distinct nucleation mode when cooled in the probe. The sampling method was also used for sampling flue gas from a circulating fluidized bed boiler fired with forest residues. The results suggest that the major fractions of Ca, K, S, and Zn were present as particles at 780degreesC, whereas most of the Cl and Pb were present as gases. The field results are consistent with results previously reported and indicate that the method can be used for efficient and precise characterization of high-temperature combustion aerosols containing inorganic vapors.
|
|
| 20. |
- Svensson, Christian, et al.
(författare)
-
Characteristics of airborne gold aggregates generated by spark discharge and high temperature evaporation furnace: Mass-mobility relationship and surface area
- 2015
-
Ingår i: Journal of Aerosol Science. - : Elsevier BV. - 0021-8502. ; 87, s. 38-52
-
Tidskriftsartikel (refereegranskat)abstract
- The properties of gas-borne aggregates are important in nano-technology and for potential health effects. Gold aggregates from three generators (one commercial and one custom built spark discharge generator and one high-temperature furnace) have been characterized. The aggregate surface areas were determined using five approaches - based on aggregation theory and/or measured aggregate properties. The characterization included mass-mobility relationships, effective densities (assessed by an Aerosol Particles Mass analyzer), primary particle analysis (based on Transmission Electron Microscopy), as well as total mass and number concentration outputs. The relationships between mass and mobility are well described by power-law functions with exponents of 2.18-2.35. For all generators, the primary particles of the aggregates were fused together by a bridge with a diameter typically similar to 60-70% of the primary particle diameter (5-10 nm). The total mass outputs were 6.1-48.1 mg/m3 and the predicted surface area outputs in the range 0.9 x 10(-3)-17 x 10(-3) cm(2)/cm(3). The aggregate effective densities differed considerably between generators. The difference could partly be explained by the differences in primary particle diameter, but not fully. This in turn may be explained either by a varying primary particle size with aggregate size, or by that there are slight differences in the morphology of the aggregates from the generators. (C) 2015 The Authors. Published by Elsevier Ltd.
|
|
| 21. |
|
|
| 22. |
|
|
