| 1. |
- Täuber, Daniela, et al.
(författare)
-
Macroscopic Domains within an Oriented TQ1 Film Visualized Using 2D Polarization Imaging
- 2017
-
Ingår i: ACS Omega. - : American Chemical Society (ACS). - 2470-1343. ; 2:1, s. 32-40
-
Tidskriftsartikel (refereegranskat)abstract
- Large-area self-assembly of functional conjugated polymers holds a great potential for practical applications of organic electronic devices. We obtained well-aligned films of poly[2,3-bis(3-octyloxyphenyl)quinoxaline-5,8-diyl-alt-thiophene-2,5-diyl] (TQ1) using the floating film transfer method. Thereby, a droplet of the TQ1 solution was injected on top of the surface of an immiscible liquid substrate, at the meniscus formed at the edge of a Petri dish, from where the polymer solution and the film spread in one direction. Characterization of the TQ1 film using the recently developed two-dimensional polarization imaging (2D POLIM) revealed large, millimeter-sized domains of oriented polymer chains. The irregular shape of the contact line at the droplet source induced the appearance of disordered stripes perpendicular to the spreading direction. A correlation of polarization parameters measured using 2D POLIM revealed the microstructure of such stripes, providing valuable information for further improvement and possible upscaling of this promising method.
|
|
| 2. |
- Bergqvist, Jonas, et al.
(författare)
-
Asymmetric photocurrent extraction in semitransparent laminated flexible organic solar cells
- 2018
-
Ingår i: npj Flexible Electronics. - : Springer Science and Business Media LLC. - 2397-4621. ; 2:1
-
Tidskriftsartikel (refereegranskat)abstract
- Scalable production methods and low-cost materials with low embodied energy are key to success for organic solar cells. PEDOT(PSS) electrodes meet these criteria and allow for low-cost and all solution-processed solar cells. However, such devices are prone to shunting. In this work we introduce a roll-to-roll lamination method to construct semitransparent solar cells with a PEDOT(PSS) anode and an polyethyleneimine (PEI) modified PEDOT(PSS) cathode. We use the polymer:PCBM active layer coated on the electrodes as the lamination adhesive. Our lamination method efficiently eliminates any shunting. Extended exposure to ambient degrades the laminated devices, which manifests in a significantly reduced photocurrent extraction when the device is illuminated through the anode, despite the fact that the PEDOT(PSS) electrodes are optically equivalent. We show that degradation-induced electron traps lead to increased trap-assisted recombination at the anode side of the device. By limiting the exposure time to ambient during production, degradation is significantly reduced. We show that lamination using the active layer as the adhesive can result in device performance equal to that of conventional sequential coating.
|
|
| 3. |
- Cai, Wanzhu, et al.
(författare)
-
Self-doped conjugated polyelectrolyte with tuneable work function for effective hole transport in polymer solar cells
- 2016
-
Ingår i: Journal of Materials Chemistry A. - : Royal Society of Chemistry. - 2050-7488 .- 2050-7496. ; 4:40, s. 15670-15675
-
Tidskriftsartikel (refereegranskat)abstract
- A water-soluble conjugated polyelectrolyte (CPE), PEDOT-S (poly(4-(2,3-dihydrothieno[3,4-b][1,4]dioxin-2-yl-methoxy)-1-butanesulfonic acid)), is demonstrated to be an excellent hole transport material in several polymer solar cells with different donor's HOMO (highest occupied molecular orbital). With a P3TI:PC71BM (poly[6,6′-bis(5′-bromo-3,4′-dioctyl-[2,2′-bithiophen]-5-yl)-1,1′-bis(2-hexyldecyl)-[3,3′-biindolinylidene]-2,2′-dione]:[6,6]-phenyl C71 butyric acid methyl ester) active layer, the device using PEDOT-S as a hole transport layer (HTL) outperforms the PEDOT:PSS-based devices due to an increased FF (fill factor). The devices' current density–voltage characteristics (J–V) show that a PEDOT-S layer can operate well with a wide range of thicknesses as well, helped by its high conductivity and decent transparency. With UV-ozone treatment, the work function of the PEDOT-S can increase from 4.9 eV to 5.2 eV. In TQ1:PC71BM (poly[[2,3-bis(3-octyloxyphenyl)-5,8-quinoxalinediyl]-2,5-thiophenediyl]:PC71BM) devices, which have a deeper donor HOMO than P3TI, Voc is improved from 0.81 V to 0.92 V by 7 min UV-ozone treatment, along with a suppressed reverse injection current and increased Jsc (short-circuit current density) and FF. Topography study shows the excellent coating ability of PEDOT-S. Conductive atomic force microscopy (C-AFM) shows the out-of-plane current in PEDOT-S film is one thousand times higher than that in PEDOT:PSS PH 4083 film under the same electric field and has much more uniformly distributed current pathways.
|
|
| 4. |
- Elfwing, Anders, et al.
(författare)
-
DNA Based Hybrid Material for Interface Engineering in Polymer Solar Cells
- 2018
-
Ingår i: ACS Applied Materials and Interfaces. - : AMER CHEMICAL SOC. - 1944-8244 .- 1944-8252. ; 10:11, s. 9579-9586
-
Tidskriftsartikel (refereegranskat)abstract
- A new solution processable electron transport material (ETM) is introduced for use in photovoltaic devices, which consists of a metallic conjugated polyelectrolyte, poly(4-(2,3-dihydrothieno[3,4-b]-[1,4]dioxin-2-yl-methoxy)-1-butanesulfonic acid (PEDOT-S), and surfactant-functionalized deoxyribonucleic acid (DNA) (named DNA:CTMA:PEDOT-S). This ETM is demonstrated to effectively work for bulk-heterojunction organic photovoltaic devices (OPV) based on different electron acceptor materials. The fill factor, the open circuit voltage, and the overall power conversion efficiency of the solar cells with a DNA:CTMA:PEDOT-S modified cathode are comparable to those of devices with a traditional lithium fluoride/aluminum cathode. The new electron transport layer has high optical transmittance, desired work function and selective electron transport. A dipole effect induced by the use of the surfactant cetyltrimethylammonium chloride (CTMA) is responsible for lowering the electrode work function. The DNA:CTMA complex works as an optical absorption dilutor, while PEDOT-S provides the conducting pathway for electron transport, and allows thicker layer to be used, enabling printing. This materials design opens a new pathway to harness and optimize the electronic and optical properties of printable interface materials.
|
|
| 5. |
- Jiang, Haiying, et al.
(författare)
-
A Highly Crystalline Wide-Band-Gap Conjugated Polymer toward High-Performance As-Cast Nonfullerene Polymer Solar Cells
- 2017
-
Ingår i: ACS Applied Materials and Interfaces. - : AMER CHEMICAL SOC. - 1944-8244 .- 1944-8252. ; 9:41, s. 36061-36069
-
Tidskriftsartikel (refereegranskat)abstract
- A new wide-band-gap conjugated polymer PBODT was successfully synthesized that showed high crystallinity and was utilized as, the active material in nonfullerene bulk-heterojunction, polymer solar cells (PSCs). The photovoltaic devices based on the as-cast blend films of PBODT with ITIC and IDIC acceptors showed notable power conversion efficiencies (PCEs) of 7.06% and 9:09%, with high open-circuit voltages of 1.00 and 0.93 V that correspond to low energy losses of 0.59 and 0.69 eV, respectively. In the case of PBODT:ITIC, lower exciton quenching efficiency and monomolecular recombination are found for devices with small driving force. On the other hand, the relatively higher driving force and suppressed monomolecular recombination for PBODT:IDIC devices are identified to be the reason for their higher short-circuit current density (J(sc)) and higher PCEs. In addition, when processed with the nonchlorinated solvent 1,2,4-trimethylbenzene, a good, PCE of 8.19% was still, achieved for the IDIC-based device. Our work shows that such wide-band-gap polymers have great potential for the environmentally friendly fabrication of highly efficient PSCs.
|
|
| 6. |
- Li, Yaohui, et al.
(författare)
-
An n-n Heterojunction Configuration for Efficient Electron Transport in Organic Photovoltaic Devices
- 2023
-
Ingår i: Advanced Functional Materials. - : WILEY-V C H VERLAG GMBH. - 1616-301X .- 1616-3028. ; 33:9
-
Tidskriftsartikel (refereegranskat)abstract
- Selective electron transport and extraction are essential to the operation of photovoltaic devices. Electron transport layer (ETL) is therefore critical to organic photovoltaics (OPV). Herein, an ETL configuration is presented comprising a solution-processed n-n organic heterojunction to enhance electron transport and hole blocking, and boost power conversion efficiency (PCE) in OPV. Specifically, the n-n heterojunction is constructed by stacking a narrow-band n-type conjugated polymer layer (PNDIT-F3N) and a wide-band n-type conjugated molecule layer (Phen-NaDPO). Based on the ultraviolet photoelectron spectroscopy measurement and numerical simulation of current density-voltage characteristics, the formation of the built-in potential is investigated. In three OPVs with different active layers, substantial improvements are observed in performance following the introduction of this ETL configuration. The performance enhancement arises from the combination of selective carrier transport properties and reduced recombination. Another contributing factor is the good film-forming quality of the new ETL configuration, where the surface energies of the related materials are well-matched. The n-n organic heterojunction represents a viable and promising ETL construction strategy for efficient OPV devices.
|
|
| 7. |
- Li, Yaohui, et al.
(författare)
-
Improved efficiency of organic solar cell using MoS2 doped poly (3,4-ethylenedioxythiophene)(PEDOT) as hole transport layer
- 2022
-
Ingår i: Applied Surface Science. - : ELSEVIER. - 0169-4332 .- 1873-5584. ; 590
-
Tidskriftsartikel (refereegranskat)abstract
- We report an efficient hole transporting layer (HTL) for organic solar cell (OSC) based on solution-processed organic-inorganic hybrid composed of ultrasonic-exfoliated MoS2 nanosheets and dopamine-copolymerized poly(3,4-ethylenedioxythiophene) (PEDOT) derivative (DA-P). The OSCs based on this new hybrid HTL show a marked performance improvement over those with single-component HTLs, and they retain up to 80% of their original power conversion efficiency after 35 days. Our investigations reveal that the boost in performance is due to a synergistic effect that improves both hole transport and extraction ability. This effect is mainly due to the doping of exfoliated-MoS2 nanosheets on DA-P. We employ a comprehensive range of spectroscopies to uncover that the dopant is derived from the oxidation products of MoS2 nanosheets during the ultrasonic exfoliation. Our work demonstrates an efficient hybrid HTL and offers new insights into the interaction of exfoliated-MoS2 nanosheets and the PEDOT derivatives.
|
|
| 8. |
- Lin, Y. B., et al.
(författare)
-
Energy-effectively printed all-polymer solar cells exceeding 8.61% efficiency
- 2018
-
Ingår i: Nano Energy. - : Elsevier BV. - 2211-2855. ; 46, s. 428-435
-
Tidskriftsartikel (refereegranskat)abstract
- All-polymer solar cells (all-PSCs) have attracted tremendous attention in the past few years due to their unique advantages. However, up to now most of high-efficiency all-PSCs are processed by spin-coating with complicated post treatment processes, which is ill-suited to a large-area roll-to-roll (R2R) technique. In this work, high-efficiency all-PSCs based on PTB7-Th and PNDI-T10 are achieved by one of R2R compatible printing techniques, i.e. doctor-blading, without any annealing treatment. It was found that incorporating an additive into all polymer blends solution can prolong the drying time of all polymer nanocomposites from 120 to 1000 s to form a better bulk heterojunction morphology and a higher crystallinity, which thus reduce charge recombination and show much better electrical impedance spectroscopy parameters. Record-breaking power conversion efficiencies (PCEs) of 8.61% and high fill factors (FF) of 0.71 are achieved by doctor-blading under an extremely process-simple and energy-effective conditions. Moreover, large-area (2.03 cm 2 ) flexible ITO-free all-PSCs by doctor-blading with record-breaking PCEs of 6.65% and FF of 0.65 are realized, which are much higher than conventional fullerene-based ones under the same condition, demonstrating that all-PSCs are more suitable for the flexible device structure and have a bright future towards practical application with R2R manufacture.
|
|
| 9. |
- Lin, Yuze, et al.
(författare)
-
Balanced Partnership between Donor and Acceptor Components in Nonfullerene Organic Solar Cells with > 12% Efficiency
- 2018
-
Ingår i: Advanced Materials. - : WILEY-V C H VERLAG GMBH. - 0935-9648 .- 1521-4095. ; 30:16
-
Tidskriftsartikel (refereegranskat)abstract
- Relative to electron donors for bulk heterojunction organic solar cells (OSCs), electron acceptors that absorb strongly in the visible and even near-infrared region are less well developed, which hinders the further development of OSCs. Fullerenes as traditional electron acceptors have relatively weak visible absorption and limited electronic tunability, which constrains the optical and electronic properties required of the donor. Here, high-performance fullerene-free OSCs based on a combination of a medium-bandgap polymer donor (FTAZ) and a narrow-bandgap nonfullerene acceptor (IDIC), which exhibit complementary absorption, matched energy levels, and blend with pure phases on the exciton diffusion length scale, are reported. The single-junction OSCs based on the FTAZ:IDIC blend exhibit power conversion efficiencies up to 12.5% with a certified value of 12.14%. Transient absorption spectroscopy reveals that exciting either the donor or the acceptor component efficiently generates mobile charges, which do not suffer from recombination to triplet states. Balancing photocurrent generation between the donor and nonfullerene acceptor removes undesirable constraints on the donor imposed by fullerene derivatives, opening a new avenue toward even higher efficiency for OSCs.
|
|
| 10. |
- Liu, Alei, et al.
(författare)
-
Manipulate Micrometer Surface and Nanometer Bulk Phase Separation Structures in the Active Layer of Organic Solar Cells via Synergy of Ultrasonic and High-Pressure Gas Spraying
- 2019
-
Ingår i: ACS Applied Materials and Interfaces. - : AMER CHEMICAL SOC. - 1944-8244 .- 1944-8252. ; 11:11, s. 10777-10784
-
Tidskriftsartikel (refereegranskat)abstract
- For organic solar cells, the vertical and lateral micro-/nanometer-scale structure in the active layer largely determines the device performance. In this work, the surface and bulk domain size of the photoactive layer are successfully manipulated with a facile two-step spraying method, that is, an ultrathin active layer by high-pressure spraying is deliberately stacked on top of the thick active layer by ultrasonic spraying. Thus, the morphology is effectively optimized with the comprehensive study of optical and electrical characteristics, such as photon absorption, exciton dissociation efficiency, and bimolecular recombination. Moreover, the novel method can be used not only in the fullerene system but also in the nonfullerene system, demonstrating the remarkable universality through this synergy method. This work provides an easy and reliable strategy to improve photovoltaic device performance in the industrial large-area spray-coating process.
|
|
| 11. |
- Luo, Xuhao, et al.
(författare)
-
Intrinsic polarization-sensitive organic photodetector with self-assembled all-polymer heterojunction
- 2022
-
Ingår i: Applied Physics Letters. - : AIP Publishing. - 0003-6951 .- 1077-3118. ; 121:23
-
Tidskriftsartikel (refereegranskat)abstract
- Intrinsic polarization-sensitive photodetectors (IPPDs) have attracted considerable attention in recent years due to their simplicity in configuration, making them ideal candidates for compact and integrated polarization-sensitive sensing and imaging systems. Photoactive films with intrinsic optical anisotropy are necessary for IPPDs. This study reports an achievement of photoactive films based on all-polymer heterojunction films with in-plane optical anisotropy using a simple bottom-up self-assembly method. Both the donor (TQ1) and acceptor (N2200) polymers have the same spatial orientation with distinct anisotropy, approaching a dichroic ratio (DR) of 8. Polarization-sensitive light absorption is due to the uniaxially oriented polymer chains, which are dominated by lamellar packing with edge-on orientation. For IPPDs based on this anisotropic all-polymer heterojunction film, a photocurrent anisotropy was found with a polarized photocurrent ratio of 2.6. The detectivity of these IPPDs was found to be 1.9 × 1011 Jones (@ ∼600 nm, 0 V bias). Our work shows that oriented polymer donor-acceptor films fabricated using bottom-up self-assembly have great potential in applications, such as polarization detection.
|
|
| 12. |
|
|
| 13. |
- Ouyang, Liangqi, et al.
(författare)
-
The contraction of PEDOT films formed on a macromolecular liquid-like surface
- 2018
-
Ingår i: Journal of Materials Chemistry C. - : ROYAL SOC CHEMISTRY. - 2050-7526 .- 2050-7534. ; 6:3, s. 654-660
-
Tidskriftsartikel (refereegranskat)abstract
- Vapour phase polymerized (VPP) PEDOT obtained using triblock copolymer PEG-PPG-PEG: Fe(III) tosylate polymeric oxidative layers has shown record-high conductivity and unique thermoelectric properties. These properties are related to the molecular weight, morphology and doping of PEDOT. Here we show that in its unwashed condition, the PEDOT chain adopts a neutral benzenoid conformation. The polymer chain converts into the charged quinoid structure after the removal of oxidizers with solvent washing. X-ray diffraction results suggest that the dopant is also incorporated into the packed polymer after the washing process. The changes in the chain structure and doping lead to the characteristic polaron and bipolaron absorption in the 800 and 1200 nm range. We observed a large contraction of the film after washing that is likely due to these changes, along with the removal of excessive polymer: oxidizer trapped in the PEDOT matrix. The contraction of films can be completely suppressed by mechanical clamping. PEDOT films without contraction show both a higher conductivity and higher optical transparency.
|
|
| 14. |
- Tang, Zheng, et al.
(författare)
-
Relating open-circuit voltage losses to the active layer morphology and contact selectivity in organic solar cells
- 2018
-
Ingår i: Journal of Materials Chemistry A. - : Royal Society of Chemistry (RSC). - 2050-7488 .- 2050-7496. ; 6:26, s. 12574-12581
-
Tidskriftsartikel (refereegranskat)abstract
- We demonstrate that voltage losses due to both radiative and non-radiative recombination of charge carriers are strongly dependent on D/A phase separation. By processing the active layer with various solvent additives, we create distinct morphologies that lead to significantly different device open-circuit voltages (VOC), even though the charge transfer state energy (ECT) of the D/A blend remains rather constant. We find that radiative recombination losses are significantly increased for a finely intermixed morphology, due to the large D/A interface area. This leads to a total recombination loss of ECT - qVOC ≈ 0.7 eV. However, considerably smaller losses (0.5 eV), due to suppressed non-radiative recombination, are possible in solar cells where the D/A materials are organized to only allow for selective charge carrier extraction. Using a drift diffusion model, we show that the origin of the reduced non-radiative recombination losses is related to an effect which has not been considered for 'optimized' solar cells-the suppression of minority carrier diffusion to the 'wrong' contact. Our results suggest that the built-in field is not sufficiently strong even in 'optimized' organic solar cells and that selective carrier extraction is critical for further improvements in VOC.
|
|
| 15. |
- Wanzhu, Cai, et al.
(författare)
-
Dedoping-induced interfacial instability of poly(ethylene imine)s-treated PEDOT:PSS as a low-work-function electrode
- 2020
-
Ingår i: Journal of Materials Chemistry C. - : ROYAL SOC CHEMISTRY. - 2050-7526 .- 2050-7534. ; 8:1, s. 328-336
-
Tidskriftsartikel (refereegranskat)abstract
- Transparent organic electrodes printed from high-conductivity PEDOT:PSS have become essential for upscaling all-carbon based, low-cost optoelectronic devices. In the printing process, low-work-function PEDOT:PSS electrodes (cathode) are achieved by coating an ultra-thin, non-conjugated polyelectrolyte that is rich in amine groups, such as poly(ethylene imine) (PEI) or its ethoxylated derivative (PEIE), onto PEDOT:PSS surfaces. Here, we mapped the physical and chemical processes that occur at the interface between thin PEIx (indicating either PEI or PEIE) and PEDOT:PSS during printing. We identify that there is a dedoping effect of PEDOT induced by the PEIx. Using infrared spectroscopy, we found that the amine-rich PEIx can form chemical bonds with the dopant, PSS. At lower PSS concentration, PEIx also shows an electron-transfer effect to the charged PEDOT chain. These interface reactions lock the surface morphology of PEDOT:PSS, preventing the redistribution of PSS, and reduce the work function. Subsequent exposure to oxygen during the device fabrication process, on the other hand, can result in redoping of the low-work-function PEDOT:PSS interface, causing problems for printing reproducible devices under ambient conditions.
|
|
| 16. |
- Yang, Junyu, et al.
(författare)
-
Roll-to-Roll Slot-Die-Printed Polymer Solar Cells by Self-Assembly
- 2018
-
Ingår i: ACS Applied Materials and Interfaces. - : AMER CHEMICAL SOC. - 1944-8244 .- 1944-8252. ; 10:26, s. 22485-22494
-
Tidskriftsartikel (refereegranskat)abstract
- Extremely simplified one-step roll-to-roll slot-die-printed flexible indium tin oxide (ITO)-free polymer solar cells (PSCs) are demonstrated based on the ternary blends of electron-donor polymer thieno[3,4-b]thiophene/benzodithiophene, electron-acceptor fullerene [6,6]-phenyl-C-71-butyric acid methyl ester, and electron-extracting polymer poly[(9,9-bis(3-(N,N-dimethylamino)propyl)-2,7-fluorene)-alt-2,7-(9,9-dioctylfluorene)] (PFN) at room temperature (RT) in ambient air. The flexible ITO-free PSC exhibits a comparable power conversion efficiency (PCE) with the device employing complicated two-step slot-die printing (5.29% vs 5.41%), which indicates that PFN molecules can migrate from the ternary nanocomposite toward the Ag cathode via vertical self-assembly during the one-step slot-die printing process in air. To confirm the migration of PFN, the morphology and elemental analysis as well as charge transport of different active layers are investigated by the in situ transient film drying process, transmission electron microscopy, atomic force microscopy, contact angle and surface energy, X-ray photoelectron spectroscopy, scanning electron microscopy, impedance spectroscopy, transient photovoltage and transient photocurrent, and laser-beam-induced current. Moreover, the good air and mechanical stability of the flexible device with a decent PCE achieved in 1 cm(2) PSCs at RT in air suggests the feasibility of energy-saving and time-saving one-step slot-die printing to large-scale roll-to-roll manufacture in the future.
|
|
