| 1. |
- Beal, Jacob, et al.
(författare)
-
Robust estimation of bacterial cell count from optical density
- 2020
-
Ingår i: Communications Biology. - : Springer Science and Business Media LLC. - 2399-3642. ; 3:1
-
Tidskriftsartikel (refereegranskat)abstract
- Optical density (OD) is widely used to estimate the density of cells in liquid culture, but cannot be compared between instruments without a standardized calibration protocol and is challenging to relate to actual cell count. We address this with an interlaboratory study comparing three simple, low-cost, and highly accessible OD calibration protocols across 244 laboratories, applied to eight strains of constitutive GFP-expressing E. coli. Based on our results, we recommend calibrating OD to estimated cell count using serial dilution of silica microspheres, which produces highly precise calibration (95.5% of residuals <1.2-fold), is easily assessed for quality control, also assesses instrument effective linear range, and can be combined with fluorescence calibration to obtain units of Molecules of Equivalent Fluorescein (MEFL) per cell, allowing direct comparison and data fusion with flow cytometry measurements: in our study, fluorescence per cell measurements showed only a 1.07-fold mean difference between plate reader and flow cytometry data.
|
|
| 2. |
- Kristan, Matej, et al.
(författare)
-
The first visual object tracking segmentation VOTS2023 challenge results
- 2023
-
Ingår i: 2023 IEEE/CVF International conference on computer vision workshops (ICCVW). - : Institute of Electrical and Electronics Engineers Inc.. - 9798350307443 - 9798350307450 ; , s. 1788-1810
-
Konferensbidrag (refereegranskat)abstract
- The Visual Object Tracking Segmentation VOTS2023 challenge is the eleventh annual tracker benchmarking activity of the VOT initiative. This challenge is the first to merge short-term and long-term as well as single-target and multiple-target tracking with segmentation masks as the only target location specification. A new dataset was created; the ground truth has been withheld to prevent overfitting. New performance measures and evaluation protocols have been created along with a new toolkit and an evaluation server. Results of the presented 47 trackers indicate that modern tracking frameworks are well-suited to deal with convergence of short-term and long-term tracking and that multiple and single target tracking can be considered a single problem. A leaderboard, with participating trackers details, the source code, the datasets, and the evaluation kit are publicly available at the challenge website1
|
|
| 3. |
- Cao, Danyang, et al.
(författare)
-
Biolubricant
- 2023
-
Ingår i: Sustainable Production Innovations. - : John Wiley & Sons. ; , s. 1-56
-
Bokkapitel (övrigt vetenskapligt/konstnärligt)
|
|
| 4. |
- Chen, Jingjing, et al.
(författare)
-
Slippage on Porous Spherical Superhydrophobic Surface Revolutionizes Heat Transfer of Non-Newtonian Fluid
- 2022
-
Ingår i: Advanced Materials Interfaces. - : John Wiley & Sons. - 2196-7350. ; 9:34
-
Tidskriftsartikel (refereegranskat)abstract
- In this study, a new strategy to achieve high-efficient heat transfer for non-Newtonian fluids with slippage using a stably prepared superhydrophobic coating is presented. A superhydrophobic coating is prepared on the inner surface of a sleeve at specific shear stress. The slippage and heat-transfer processes of the typical non-Newtonian fluid–1% carboxymethyl cellulose solutions on the superhydrophobic coating are investigated simultaneously. A novel porous spherical type of superhydrophobic coating with a contact angle of 168° is obtained. It is found that the shear stress in electrodeposition is a key parameter to control the morphology and wetting ability of the superhydrophobic coating. The slip length and enhancement factor of heat transfer for the non-Newtonian fluid on the coating are found in a range of 20–900 µm and 1.47 experimentally. A new parameter is proposed as Reynolds number Re divided by the dimensionless slip length ls* (Re/ls*) for the heat-transfer enhancement with slippage, which can be used as the guide for designing coating and selecting the operating conditions. The Re/ls* is <4, which can enhance the heat transfer via the slippage.
|
|
| 5. |
- Wu, Jian, et al.
(författare)
-
High load capacity with Ionic liquid-lubricated tribological system
- 2016
-
Ingår i: Tribology International. - : Elsevier BV. - 0301-679X .- 1879-2464. ; 94, s. 315-322
-
Tidskriftsartikel (refereegranskat)abstract
- Engineering polymers with high glass transition temperature have been widely used in dynamic friction systems by oil or solid lubrication. However, in high-load systems, oil lubrication is less efficient due to the viscosity decrease at higher temperatures induced by friction heat. [Bmim][PF6] ionic liquid was used and compared with traditional L-HM46 oil and solid PTFE. Taking advantage of high [Bmim][PF6] viscosity, strong steel-[Bmim][PF6] but poor PEEK-[Bmim][PF6] interaction, the [Bmim][PF6] lubricated PEEK/steel slide falls in hydrodynamic lubrication and elastohydrodynamic lubrication region under 150–1500 N. While the oil and PTFE both failed to lubricate under 800 N.
|
|
| 6. |
- Zhou, Qilong, et al.
(författare)
-
Versatile Ionic Gel Driven by Dual Hydrogen Bond Networks : Toward Advanced Lubrication And Self-Healing
- 2021
-
Ingår i: ACS Applied Polymer Materials. - : American Chemical Society (ACS). - 2637-6105. ; 3:11, s. 5932-5941
-
Tidskriftsartikel (refereegranskat)abstract
- From one to more, the same raw materials giving rise to multifarious products is one of the goals of researchers to pursue industrial efficiency. Herein, we designed a formula (controlling the content of the matrix) to prepare two functional ionic gels, integrating the excellent lubrication, thermal conductivity, and self-healing ability to meet different industrial demands of the lubrication and biomedical fields. Deep eutectic solvents (DESs) of urea/choline chloride (UCC) and glycerol/choline chloride (GCC) were locked in polyacrylamide (PAM) ionic gel formed by acrylamide (AM) and a photoinitiator by freer-adical polymerization. The unique dual hydrogen bond network in the ionic gel causes the material to exhibit a low wear rate, which can effectively reduce the wear of metal contact. With the addition of PAM, the ionic gel has excellent mechanical strength and good recovery performance. Unexpectedly, this dense hydrogen bond network enhances thermal conductivity by optimizing phonon and electron transfer. The versatile ionic gel has a good application prospect as a substitute for industrial lubricants and medical device materials.
|
|
