| 1. |
- Thomas, HS, et al.
(författare)
-
- 2019
-
swepub:Mat__t
|
|
| 2. |
- Ademuyiwa, Adesoji O., et al.
(författare)
-
Determinants of morbidity and mortality following emergency abdominal surgery in children in low-income and middle-income countries
- 2016
-
Ingår i: BMJ Global Health. - : BMJ Publishing Group Ltd. - 2059-7908. ; 1:4
-
Tidskriftsartikel (refereegranskat)abstract
- Background: Child health is a key priority on the global health agenda, yet the provision of essential and emergency surgery in children is patchy in resource-poor regions. This study was aimed to determine the mortality risk for emergency abdominal paediatric surgery in low-income countries globally.Methods: Multicentre, international, prospective, cohort study. Self-selected surgical units performing emergency abdominal surgery submitted prespecified data for consecutive children aged <16 years during a 2-week period between July and December 2014. The United Nation's Human Development Index (HDI) was used to stratify countries. The main outcome measure was 30-day postoperative mortality, analysed by multilevel logistic regression.Results: This study included 1409 patients from 253 centres in 43 countries; 282 children were under 2 years of age. Among them, 265 (18.8%) were from low-HDI, 450 (31.9%) from middle-HDI and 694 (49.3%) from high-HDI countries. The most common operations performed were appendectomy, small bowel resection, pyloromyotomy and correction of intussusception. After adjustment for patient and hospital risk factors, child mortality at 30 days was significantly higher in low-HDI (adjusted OR 7.14 (95% CI 2.52 to 20.23), p<0.001) and middle-HDI (4.42 (1.44 to 13.56), p=0.009) countries compared with high-HDI countries, translating to 40 excess deaths per 1000 procedures performed.Conclusions: Adjusted mortality in children following emergency abdominal surgery may be as high as 7 times greater in low-HDI and middle-HDI countries compared with high-HDI countries. Effective provision of emergency essential surgery should be a key priority for global child health agendas.
|
|
| 3. |
- Holmes, Natalie P., et al.
(författare)
-
Engineering Two-Phase and Three-Phase Microstructures from Water-Based Dispersions of Nanoparticles for Eco-Friendly Polymer Solar Cell Applications
- 2018
-
Ingår i: Chemistry of Materials. - : American Chemical Society (ACS). - 0897-4756 .- 1520-5002. ; 30:18, s. 6521-6531
-
Tidskriftsartikel (refereegranskat)abstract
- Nanoparticle organic photovoltaics, a subfield of organic photovoltaics (OPV), has attracted increasing interest in recent years due to the eco-friendly fabrication of solar modules afforded by colloidal ink technology. Importantly, using this approach it is now possible to engineer the microstructure of the light absorbing/charge generating layer of organic photovoltaics; decoupling film morphology from film deposition. In this study, single-component nanoparticles of poly(3-hexylthiophene) (P3HT) and phenyl-C61 butyric acid methyl ester (PC61BM) were synthesized and used to generate a two-phase microstructure with control over domain size prior to film deposition. Scanning transmission X-ray microscopy (STXM) and electron microscopy were used to characterize the thin film morphology. Uniquely, the measured microstructure was a direct input for a nanoscopic kinetic Monte Carlo (KMC) model allowing us to assess exciton transport properties that are experimentally inaccessible in these single-component particles. Photoluminescence, UV-vis spectroscopy measurements, and KMC results of the nanoparticle thin films enabled the calculation of an experimental exciton dissociation efficiency (ηED) of 37% for the two-phase microstructure. The glass transition temperature (Tg) of the materials was characterized with dynamic mechanical thermal analysis (DMTA) and thermal annealing led to an increase in ηED to 64% due to an increase in donor-acceptor interfaces in the thin film from both sintering of neighboring opposite-type particles in addition to the generation of a third mixed phase from diffusion of PC61BM into amorphous P3HT domains. As such, this study demonstrates the higher level of control over donor-acceptor film morphology enabled by customizing nanoparticulate colloidal inks, where the optimal three-phase film morphology for an OPV photoactive layer can be designed and engineered.
|
|
| 4. |
- Holmes, Natalie P., et al.
(författare)
-
Unravelling donor–acceptor film morphologyformation for environmentally-friendly OPV inkformulations
- 2019
-
Ingår i: Green Chemistry. - : Royal Society of Chemistry. - 1463-9262 .- 1463-9270. ; 21:18, s. 5090-5103
-
Tidskriftsartikel (refereegranskat)abstract
- The challenge of coating organic photovoltaics (OPV) from green solvents is to achieve the requirednanostructured interpenetrating network of donor and acceptor domains based on a rational choice ofsolvent approach as opposed to the usual trial-and-error methods. We demonstrate here that we canachieve a bicontinuous interpenetrating network with nanoscale phase separation for the chosen donor–acceptor material system poly[2,3-bis-(3-octyloxyphenyl)quinoxaline-5,8-diyl-alt-thiophene-2,5-diyl]:phenyl-C61 butyric acid methyl ester (TQ1:PC61BM) when processing from green solvent ink formulations.This structure is achieved by first calculating the Hansen solubility parameters (HSP) of the donor andacceptor materials, followed by careful choice of solvents with selective relative solubilities for the twomaterials based on the desired order of precipitation necessary for forming a nanostructured interdigitatednetwork morphology. We found that the relative distances in Hansen space (Ra) between TQ1 andthe primary solvent, on the one hand, and PC61BM and the primary solvent, on the other hand, could becorrelated to the donor–acceptor morphology for the formulations based on the solvents d-limonene,anisole, and 2-methyl anisole, as well as the halogenated reference solvent o-dichlorobenzene. Thisnanostructured blend film morphology was characterised with scanning transmission X-ray microscopy(STXM) and transmission electron microscopy (TEM), and the film surface composition was analysed bynear edge X-ray absorption fine structure (NEXAFS) spectroscopy. Hansen solubility theory, based onsolution thermodynamics, has been used and we propose an HSP-based method that is a general platformfor the rational design of ink formulations for solution-based organic electronics, in particular facilitatingthe green solvent transition of organic photovoltaics. Our results show that the bulk heterojunctionmorphology for a donor–acceptor system processed from customised solvent mixtures can be predictedby the HSP-based method with good reliability.
|
|
