| 1. |
|
|
| 2. |
- Beal, Jacob, et al.
(författare)
-
Robust estimation of bacterial cell count from optical density
- 2020
-
Ingår i: Communications Biology. - : Springer Science and Business Media LLC. - 2399-3642. ; 3:1
-
Tidskriftsartikel (refereegranskat)abstract
- Optical density (OD) is widely used to estimate the density of cells in liquid culture, but cannot be compared between instruments without a standardized calibration protocol and is challenging to relate to actual cell count. We address this with an interlaboratory study comparing three simple, low-cost, and highly accessible OD calibration protocols across 244 laboratories, applied to eight strains of constitutive GFP-expressing E. coli. Based on our results, we recommend calibrating OD to estimated cell count using serial dilution of silica microspheres, which produces highly precise calibration (95.5% of residuals <1.2-fold), is easily assessed for quality control, also assesses instrument effective linear range, and can be combined with fluorescence calibration to obtain units of Molecules of Equivalent Fluorescein (MEFL) per cell, allowing direct comparison and data fusion with flow cytometry measurements: in our study, fluorescence per cell measurements showed only a 1.07-fold mean difference between plate reader and flow cytometry data.
|
|
| 3. |
- Kristan, Matej, et al.
(författare)
-
The Visual Object Tracking VOT2016 Challenge Results
- 2016
-
Ingår i: COMPUTER VISION - ECCV 2016 WORKSHOPS, PT II. - Cham : SPRINGER INT PUBLISHING AG. - 9783319488813 - 9783319488806 ; , s. 777-823
-
Konferensbidrag (refereegranskat)abstract
- The Visual Object Tracking challenge VOT2016 aims at comparing short-term single-object visual trackers that do not apply pre-learned models of object appearance. Results of 70 trackers are presented, with a large number of trackers being published at major computer vision conferences and journals in the recent years. The number of tested state-of-the-art trackers makes the VOT 2016 the largest and most challenging benchmark on short-term tracking to date. For each participating tracker, a short description is provided in the Appendix. The VOT2016 goes beyond its predecessors by (i) introducing a new semi-automatic ground truth bounding box annotation methodology and (ii) extending the evaluation system with the no-reset experiment.
|
|
| 4. |
-
- 2019
-
Tidskriftsartikel (refereegranskat)
|
|
| 5. |
- Kristan, Matej, et al.
(författare)
-
The Visual Object Tracking VOT2015 challenge results
- 2015
-
Ingår i: Proceedings 2015 IEEE International Conference on Computer Vision Workshops ICCVW 2015. - : IEEE. - 9780769557205 ; , s. 564-586
-
Konferensbidrag (refereegranskat)abstract
- The Visual Object Tracking challenge 2015, VOT2015, aims at comparing short-term single-object visual trackers that do not apply pre-learned models of object appearance. Results of 62 trackers are presented. The number of tested trackers makes VOT 2015 the largest benchmark on short-term tracking to date. For each participating tracker, a short description is provided in the appendix. Features of the VOT2015 challenge that go beyond its VOT2014 predecessor are: (i) a new VOT2015 dataset twice as large as in VOT2014 with full annotation of targets by rotated bounding boxes and per-frame attribute, (ii) extensions of the VOT2014 evaluation methodology by introduction of a new performance measure. The dataset, the evaluation kit as well as the results are publicly available at the challenge website(1).
|
|
| 6. |
- Kristan, Matej, et al.
(författare)
-
The Visual Object Tracking VOT2017 challenge results
- 2017
-
Ingår i: 2017 IEEE INTERNATIONAL CONFERENCE ON COMPUTER VISION WORKSHOPS (ICCVW 2017). - : IEEE. - 9781538610343 ; , s. 1949-1972
-
Konferensbidrag (refereegranskat)abstract
- The Visual Object Tracking challenge VOT2017 is the fifth annual tracker benchmarking activity organized by the VOT initiative. Results of 51 trackers are presented; many are state-of-the-art published at major computer vision conferences or journals in recent years. The evaluation included the standard VOT and other popular methodologies and a new "real-time" experiment simulating a situation where a tracker processes images as if provided by a continuously running sensor. Performance of the tested trackers typically by far exceeds standard baselines. The source code for most of the trackers is publicly available from the VOT page. The VOT2017 goes beyond its predecessors by (i) improving the VOT public dataset and introducing a separate VOT2017 sequestered dataset, (ii) introducing a realtime tracking experiment and (iii) releasing a redesigned toolkit that supports complex experiments. The dataset, the evaluation kit and the results are publicly available at the challenge website(1).
|
|
| 7. |
- Liu, Tao, et al.
(författare)
-
16% efficiency all-polymer organic solar cells enabled by a finely tuned morphology via the design of ternary blend
- 2021
-
Ingår i: Joule. - : CELL PRESS. - 2542-4351. ; 5:4, s. 914-930
-
Tidskriftsartikel (refereegranskat)abstract
- A SUMMARY There is an urgent demand for all-polymer organic solar cells (AP-OSCs) to gain higher efficiency. Here, we successfully improve the performance to 16.09% by introducing a small amount of BN-T, a B <- N-type polymer acceptor, into the PM6:PY-IT blend. It has been found that BN-T makes the active layer, based on the PM6:PY-IT:BN-T ternary blend, more crystalline but meanwhile slightly reduces the phase separation, leading to enhancement of both exciton harvesting and charge transport. From a thermodynamic viewpoint, BN-T prefers to reside between PM6 and PY-IT, and the fraction of this fine-tunes the morphology. Besides, a significantly reduced nonradiative energy loss occurs in the ternary blend, along with the coexistence of energy and charge transfer between the two acceptors. The progressive performance facilitated by these improved properties demonstrates that AP-OSCs can possibly comparably efficient with those based on small molecule acceptors, further enhancing the competitiveness of this device type.
|
|
| 8. |
- Luo, Yifei, et al.
(författare)
-
Technology Roadmap for Flexible Sensors
- 2023
-
Ingår i: ACS Nano. - : American Chemical Society. - 1936-0851 .- 1936-086X. ; 17:6, s. 5211-5295
-
Forskningsöversikt (refereegranskat)abstract
- Humans rely increasingly on sensors to address grand challenges and to improve quality of life in the era of digitalization and big data. For ubiquitous sensing, flexible sensors are developed to overcome the limitations of conventional rigid counterparts. Despite rapid advancement in bench-side research over the last decade, the market adoption of flexible sensors remains limited. To ease and to expedite their deployment, here, we identify bottlenecks hindering the maturation of flexible sensors and propose promising solutions. We first analyze challenges in achieving satisfactory sensing performance for real-world applications and then summarize issues in compatible sensor-biology interfaces, followed by brief discussions on powering and connecting sensor networks. Issues en route to commercialization and for sustainable growth of the sector are also analyzed, highlighting environmental concerns and emphasizing nontechnical issues such as business, regulatory, and ethical considerations. Additionally, we look at future intelligent flexible sensors. In proposing a comprehensive roadmap, we hope to steer research efforts towards common goals and to guide coordinated development strategies from disparate communities. Through such collaborative efforts, scientific breakthroughs can be made sooner and capitalized for the betterment of humanity.
|
|
| 9. |
- Ma, Ruijie, et al.
(författare)
-
Adding a Third Component with Reduced Miscibility and Higher LUMO Level Enables Efficient Ternary Organic Solar Cells
- 2020
-
Ingår i: ACS Energy Letters. - : American Chemical Society (ACS). - 2380-8195. ; 5:8, s. 2711-2720
-
Tidskriftsartikel (refereegranskat)abstract
- It is widely known that the miscibility between donor and acceptor is a crucial factor that affects the morphology and thus device performance of nonfullerene organic solar cells (OSCs). In this Letter, we show that incorporating a third component with lower miscibility and higher lowest unoccupied molecular orbital (LUMO) level into the state-of-the-art PM6:Y6 system can significantly enhance the performance of devices. The best results of the ternary devices are achieved by adding a small molecular acceptor named ITCPTC (similar to 5% w/w), which significantly improves the power conversion efficiency (PCE) of the host system from 16.44% to 17.42%. The higher LUMO of the third component increases the open-circuit voltage (V-oc), while the low miscibility enlarges the domains and leads to improved short-circuit current density (J(sc)) and fill factor (FF). The efficacy of this strategy is supported by using other nonfullerene third components including an asymmetric small molecule (N7IT) and a polymer acceptor (PF2-DTC), which play the same role as ITCPTC and boost the PCEs to 16.96% and 17.04%, respectively. Our approach can be potentially applied to a wide range of OSC material systems and should facilitate the development of the OSC field.
|
|
| 10. |
- Aad, G, et al.
(författare)
-
- 2015
-
swepub:Mat__t
|
|
| 11. |
|
|
| 12. |
|
|
| 13. |
|
|
| 14. |
- Felsberg, Michael, 1974-, et al.
(författare)
-
The Thermal Infrared Visual Object Tracking VOT-TIR2016 Challenge Results
- 2016
-
Ingår i: Computer Vision – ECCV 2016 Workshops. ECCV 2016.. - Cham : SPRINGER INT PUBLISHING AG. - 9783319488813 - 9783319488806 ; , s. 824-849
-
Konferensbidrag (refereegranskat)abstract
- The Thermal Infrared Visual Object Tracking challenge 2016, VOT-TIR2016, aims at comparing short-term single-object visual trackers that work on thermal infrared (TIR) sequences and do not apply pre-learned models of object appearance. VOT-TIR2016 is the second benchmark on short-term tracking in TIR sequences. Results of 24 trackers are presented. For each participating tracker, a short description is provided in the appendix. The VOT-TIR2016 challenge is similar to the 2015 challenge, the main difference is the introduction of new, more difficult sequences into the dataset. Furthermore, VOT-TIR2016 evaluation adopted the improvements regarding overlap calculation in VOT2016. Compared to VOT-TIR2015, a significant general improvement of results has been observed, which partly compensate for the more difficult sequences. The dataset, the evaluation kit, as well as the results are publicly available at the challenge website.
|
|
| 15. |
- Fenstermacher, M.E., et al.
(författare)
-
DIII-D research advancing the physics basis for optimizing the tokamak approach to fusion energy
- 2022
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 0029-5515 .- 1741-4326. ; 62:4
-
Tidskriftsartikel (refereegranskat)abstract
- DIII-D physics research addresses critical challenges for the operation of ITER and the next generation of fusion energy devices. This is done through a focus on innovations to provide solutions for high performance long pulse operation, coupled with fundamental plasma physics understanding and model validation, to drive scenario development by integrating high performance core and boundary plasmas. Substantial increases in off-axis current drive efficiency from an innovative top launch system for EC power, and in pressure broadening for Alfven eigenmode control from a co-/counter-I p steerable off-axis neutral beam, all improve the prospects for optimization of future long pulse/steady state high performance tokamak operation. Fundamental studies into the modes that drive the evolution of the pedestal pressure profile and electron vs ion heat flux validate predictive models of pedestal recovery after ELMs. Understanding the physics mechanisms of ELM control and density pumpout by 3D magnetic perturbation fields leads to confident predictions for ITER and future devices. Validated modeling of high-Z shattered pellet injection for disruption mitigation, runaway electron dissipation, and techniques for disruption prediction and avoidance including machine learning, give confidence in handling disruptivity for future devices. For the non-nuclear phase of ITER, two actuators are identified to lower the L-H threshold power in hydrogen plasmas. With this physics understanding and suite of capabilities, a high poloidal beta optimized-core scenario with an internal transport barrier that projects nearly to Q = 10 in ITER at ∼8 MA was coupled to a detached divertor, and a near super H-mode optimized-pedestal scenario with co-I p beam injection was coupled to a radiative divertor. The hybrid core scenario was achieved directly, without the need for anomalous current diffusion, using off-axis current drive actuators. Also, a controller to assess proximity to stability limits and regulate β N in the ITER baseline scenario, based on plasma response to probing 3D fields, was demonstrated. Finally, innovative tokamak operation using a negative triangularity shape showed many attractive features for future pilot plant operation.
|
|
| 16. |
|
|
| 17. |
- Mishra, A, et al.
(författare)
-
Diminishing benefits of urban living for children and adolescents' growth and development
- 2023
-
Ingår i: Nature. - : Springer Science and Business Media LLC. - 1476-4687 .- 0028-0836. ; 615:7954, s. 874-883
-
Tidskriftsartikel (refereegranskat)abstract
- Optimal growth and development in childhood and adolescence is crucial for lifelong health and well-being1–6. Here we used data from 2,325 population-based studies, with measurements of height and weight from 71 million participants, to report the height and body-mass index (BMI) of children and adolescents aged 5–19 years on the basis of rural and urban place of residence in 200 countries and territories from 1990 to 2020. In 1990, children and adolescents residing in cities were taller than their rural counterparts in all but a few high-income countries. By 2020, the urban height advantage became smaller in most countries, and in many high-income western countries it reversed into a small urban-based disadvantage. The exception was for boys in most countries in sub-Saharan Africa and in some countries in Oceania, south Asia and the region of central Asia, Middle East and north Africa. In these countries, successive cohorts of boys from rural places either did not gain height or possibly became shorter, and hence fell further behind their urban peers. The difference between the age-standardized mean BMI of children in urban and rural areas was <1.1 kg m–2 in the vast majority of countries. Within this small range, BMI increased slightly more in cities than in rural areas, except in south Asia, sub-Saharan Africa and some countries in central and eastern Europe. Our results show that in much of the world, the growth and developmental advantages of living in cities have diminished in the twenty-first century, whereas in much of sub-Saharan Africa they have amplified.
|
|
| 18. |
|
|
| 19. |
- Van Asbroeck, Stephanie, et al.
(författare)
-
Lifestyle and incident dementia: A COSMIC individual participant data meta-analysis
- 2024
-
Ingår i: ALZHEIMERS & DEMENTIA. - 1552-5260 .- 1552-5279. ; 20:6, s. 3972-3986
-
Tidskriftsartikel (refereegranskat)abstract
- INTRODUCTIONThe LIfestyle for BRAin Health (LIBRA) index yields a dementia risk score based on modifiable lifestyle factors and is validated in Western samples. We investigated whether the association between LIBRA scores and incident dementia is moderated by geographical location or sociodemographic characteristics. METHODSWe combined data from 21 prospective cohorts across six continents (N = 31,680) and conducted cohort-specific Cox proportional hazard regression analyses in a two-step individual participant data meta-analysis. RESULTSA one-standard-deviation increase in LIBRA score was associated with a 21% higher risk for dementia. The association was stronger for Asian cohorts compared to European cohorts, and for individuals aged <= 75 years (vs older), though only within the first 5 years of follow-up. No interactions with sex, education, or socioeconomic position were observed. DISCUSSIONModifiable risk and protective factors appear relevant for dementia risk reduction across diverse geographical and sociodemographic groups. Highlights A two-step individual participant data meta-analysis was conducted. This was done at a global scale using data from 21 ethno-regionally diverse cohorts. The association between a modifiable dementia risk score and dementia was examined. The association was modified by geographical region and age at baseline. Yet, modifiable dementia risk and protective factors appear relevant in all investigated groups and regions.
|
|
| 20. |
|
|
| 21. |
- Winkler, TW, et al.
(författare)
-
Differential and shared genetic effects on kidney function between diabetic and non-diabetic individuals
- 2022
-
Ingår i: Communications biology. - : Springer Science and Business Media LLC. - 2399-3642. ; 5:1, s. 580-
-
Tidskriftsartikel (refereegranskat)abstract
- Reduced glomerular filtration rate (GFR) can progress to kidney failure. Risk factors include genetics and diabetes mellitus (DM), but little is known about their interaction. We conducted genome-wide association meta-analyses for estimated GFR based on serum creatinine (eGFR), separately for individuals with or without DM (nDM = 178,691, nnoDM = 1,296,113). Our genome-wide searches identified (i) seven eGFR loci with significant DM/noDM-difference, (ii) four additional novel loci with suggestive difference and (iii) 28 further novel loci (including CUBN) by allowing for potential difference. GWAS on eGFR among DM individuals identified 2 known and 27 potentially responsible loci for diabetic kidney disease. Gene prioritization highlighted 18 genes that may inform reno-protective drug development. We highlight the existence of DM-only and noDM-only effects, which can inform about the target group, if respective genes are advanced as drug targets. Largely shared effects suggest that most drug interventions to alter eGFR should be effective in DM and noDM.
|
|
| 22. |
- Wu, Zi Yi, et al.
(författare)
-
Convective transport characteristics of condensing droplets in moist air flow
- 2023
-
Ingår i: Physics of Fluids. - : AIP Publishing. - 1070-6631 .- 1089-7666. ; 35:2
-
Tidskriftsartikel (refereegranskat)abstract
- Condensation of convective moist air flow is a crucial physical process and is directly related to various industries. It is essential to understand the underlying growth mechanism of condensing droplets, while past studies have commonly considered convective transport with a negligible/simplified approach. In this work, a three-dimensional transient multiphysics coupling model was developed to investigate the transport characteristics of condensing droplets in convective moist air flow. This model typically interconnects heat transfer with vapor-liquid phase change, mass transport, and fluid flow. The results reveal that convective flow significantly dominates heat and mass transport during condensation. On the gas side, the incoming flow thins the diffusion layer at the windward part with a large concentration gradient. However, a low vapor-concentration zone behind the droplet is formed due to the resulting rear-side vortex, which presents an increased influence as the contact angle increases. By forcing molecular diffusion with convection transport, vapor transport from surroundings to the condensing interface is enhanced several times depending on the Reynolds number. Within the droplet, the flow shearing at the interface is principally responsible for the strong internal convection, while the Marangoni effect is negligible. The internal flow greatly affects the droplet temperature profile with a large gradient close to the base. Finally, convective flow contributes to over 3.3 times higher overall heat transfer coefficient than the quiescent environment. In addition, in interaction-governed growth, transport characteristics depend on not only the size and space distributions of droplets but also the interaction between droplets and convective flow.
|
|
| 23. |
|
|
| 24. |
- You, Xiaohu, et al.
(författare)
-
Towards 6G wireless communication networks: vision, enabling technologies, and new paradigm shifts
- 2021
-
Ingår i: Science China Information Sciences. - : Science Press. - 1674-733X .- 1869-1919. ; 64:1
-
Forskningsöversikt (refereegranskat)abstract
- The fifth generation (5G) wireless communication networks are being deployed worldwide from 2020 and more capabilities are in the process of being standardized, such as mass connectivity, ultra-reliability, and guaranteed low latency. However, 5G will not meet all requirements of the future in 2030 and beyond, and sixth generation (6G) wireless communication networks are expected to provide global coverage, enhanced spectral/energy/cost efficiency, better intelligence level and security, etc. To meet these requirements, 6G networks will rely on new enabling technologies, i.e., air interface and transmission technologies and novel network architecture, such as waveform design, multiple access, channel coding schemes, multi-antenna technologies, network slicing, cell-free architecture, and cloud/fog/edge computing. Our vision on 6G is that it will have four new paradigm shifts. First, to satisfy the requirement of global coverage, 6G will not be limited to terrestrial communication networks, which will need to be complemented with non-terrestrial networks such as satellite and unmanned aerial vehicle (UAV) communication networks, thus achieving a space-air-ground-sea integrated communication network. Second, all spectra will be fully explored to further increase data rates and connection density, including the sub-6 GHz, millimeter wave (mmWave), terahertz (THz), and optical frequency bands. Third, facing the big datasets generated by the use of extremely heterogeneous networks, diverse communication scenarios, large numbers of antennas, wide bandwidths, and new service requirements, 6G networks will enable a new range of smart applications with the aid of artificial intelligence (AI) and big data technologies. Fourth, network security will have to be strengthened when developing 6G networks. This article provides a comprehensive survey of recent advances and future trends in these four aspects. Clearly, 6G with additional technical requirements beyond those of 5G will enable faster and further communications to the extent that the boundary between physical and cyber worlds disappears.
|
|
| 25. |
- Yuan, Zhongcheng, et al.
(författare)
-
Approximately 800-nm-Thick Pinhole-Free Perovskite Films via Facile Solvent Retarding Process for Efficient Planar Solar Cells
- 2016
-
Ingår i: ACS APPLIED MATERIALS and INTERFACES. - : AMER CHEMICAL SOC. - 1944-8244 .- 1944-8252. ; 8:50, s. 34446-34454
-
Tidskriftsartikel (refereegranskat)abstract
- Device performance of organometal halide perovskite solar cells significantly depends on the quality and thickness of perovskite absorber films. However, conventional deposition methods often generate pinholes within similar to 300 nm-thick perovskite films, which are detrimental to the large area device manufacture. Here we demonstrated a simple solvent retarding process to deposit uniform pinhole free perovskite films with thicknesses up to similar to 800 nm. Solvent evaporation during the retarding process facilitated the components separation in the mixed halide perovskite precursors, and hence the final films exhibited pinhole free morphology and large grain sizes. In addition, the increased precursor concentration after solvent-retarding process led to thick perovskite films. Based on the uniform and thick perovskite films prepared by this convenient process, a champion device efficiency up to 16.8% was achieved. We believe that this simple deposition procedure for high quality perovskite films around micrometer thickness has a great potential in the application of large area perovskite solar cells and other optoelectronic devices.
|
|
| 26. |
- Zheng, Shao Fei, et al.
(författare)
-
Theoretical and Three-Dimensional Molecular Dynamics Study of Droplet Wettability and Mobility on Lubricant-Infused Porous Surfaces
- 2023
-
Ingår i: Langmuir. - 0743-7463. ; 39:37, s. 13371-13385
-
Tidskriftsartikel (refereegranskat)abstract
- Profiting from their slippery nature, lubricant-infused porous surfaces endow with droplets excellent mobility and consequently promise remarkable heat transfer improvement for dropwise condensation. To be a four-phase wetting system, the droplet wettability configurations and the corresponding dynamic characteristics on lubricant-infused porous surfaces are closely related to many factors, such as multiple interfacial interactions, surface features, and lubricant thickness, which keeps a long-standing challenge to promulgate the underlying physics. In this work, thermodynamically theoretical analysis and three-dimensional molecular dynamics simulations with the coarse-grained water and hexane models are carried out to explore droplet wettability and mobility on lubricant-infused porous surfaces. Combined with accessible theoretical criteria, phase diagrams of droplet configurations are constructed with a comprehensive consideration of interfacial interactions, surface structures, and lubricant thickness. Subsequently, droplet sliding and coalescence dynamics are quantitatively defined under different configurations. Finally, in terms of the promotion of dropwise condensation, a non-cloaking configuration with the encapsulated state underneath the droplet is recommended to achieve high droplet mobility owing to the low viscous drag of the lubricant and the eliminated pinning effect of the contact line. On the basis of the low oil-water and water-solid interactions, a stable lubricant layer with a relatively low thickness is suggested to construct slippery surfaces.
|
|
| 27. |
|
|
| 28. |
- Zou, Yatao, et al.
(författare)
-
Thermal-induced interface degradation in perovskite light-emitting diodes
- 2020
-
Ingår i: Journal of Materials Chemistry C. - : ROYAL SOC CHEMISTRY. - 2050-7526 .- 2050-7534. ; 8:43, s. 15079-15085
-
Tidskriftsartikel (refereegranskat)abstract
- Perovskite light-emitting diodes (PeLEDs) have experienced rapid improvements in device efficiency during the last several years. However, the operational instability of PeLEDs remains a key barrier hindering their practical applications. A fundamental understanding of the degradation mechanism is still lacking but will be important to seek ways to mitigate these unwanted processes. In this work, through comprehensive characterizations of the perovskite emitters and the interfacial contacts, we figure out that Joule heating induced interface degradation is one of the dominant factors affecting the operational stability of PeLEDs. We investigate the interfacial contacts of PeLEDs based on a commonly used device structure, with an organic electron transport layer of 1,3,5-tris(N-phenylbenzimiazole-2-yl)benzene (TPBi), and observe obvious photoluminescence quenching of the perovskite layer after device operation. Detailed characterizations of the interlayers and the interfacial contacts reveal that photoluminescence quenching is mainly due to the element inter-diffusion at the interface induced by the morphological evolution of the TPBi layers under Joule heating during the operation of PeLEDs. Our work provides direct insights into the degradation pathways and highlights the importance of exploring intrinsically stable interlayers as well as interfacial contacts beyond the state-of-the-art to further boost the operational stability of PeLEDs.
|
|
| 29. |
|
|
| 30. |
- Alström, Per, et al.
(författare)
-
Phylogeny and classification of the Old World Emberizini (Aves, Passeriformes)
- 2008
-
Ingår i: Molecular Phylogenetics and Evolution. - : Elsevier BV. - 1055-7903 .- 1095-9513. ; 47:3, s. 960-973
-
Tidskriftsartikel (refereegranskat)abstract
- The phylogeny of the avian genus Emberiza and the monotypic genera Latoucheornis, Melophus and Miliaria (collectively the Old World Emberizini), as well as representatives for the New World Emberizini, the circumpolar genera Calcarius and Plectrophertax and the four other generally recognized tribes in the subfamily Emberizinae was estimated based on the mitochondrial cytochrome b gene and introns 6-7 of the nuclear ornithine decarboxylase (ODC) gene. Our results support monophyly of the Old World Emberizini, but do not corroborate a sister relationship to the New World Emberizini. Calcarius and Plectrophenax form a clade separated from the other Emberizini. This agrees with previous studies, and we recommend the use of the name Calcariini. Latoucheornis, Melophus and Miliaria are nested within Emberiza, and we therefore propose they be synonymized with Emberiza. Emberiza is divided into four main clades, whose relative positions are uncertain, although a sister relation between a clade with six African species and one comprising the rest of the species (30, all Palearctic) is most likely. Most clades agree with traditional, morphology-based, classifications. However, four sister relationships within Emberiza, three of which involve the previously recognized Latoucheornis, Melophus and Miliaria, are unpredicted, and reveal cases of strong morphological divergence. In contrast, the plumage similarity between adult male Emberiza (formerly Latoucheornis) siemsseni and the nominate subspecies of the New World Junco hyemalis is shown to be the result of parallel evolution. A further case of parallel plumage evolution, between African and Eurasian taxa, is pointed out. Two cases of discordance between the mitochondrial and nuclear data with respect to branch lengths and genetic divergences are considered to be the result of introgressive hybridization.
|
|
| 31. |
- An, Bolun, et al.
(författare)
-
An approach to evaluate wheel-rail match properties considering the flexibility of ballastless track : Comparison of rigid and flexible track models in wheel-rail profile matching
- 2019
-
Ingår i: International Journal of COMADEM. - : COMADEM International. - 1363-7681. ; 22:3, s. 5-13
-
Tidskriftsartikel (refereegranskat)abstract
- Many different wheel/rail profiles are used in the China high-speed railway, and vehicle operation safety and comfort will decrease if the inappropriate wheel-rail profile pair is used. To solve the problem of estimating the wheel-rail match, many numerical models, including vehicle system dynamic models and wheel-rail rolling contact models, have been established to analyse the wheel-rail dynamic responses. Both methods have less consideration of the flexibility and vibration characteristics of ballastless track, leading to deviations in the calculation of middle and high frequency vibration. This paper proposes a vehicle-flexible track coupling model and compares it with the vehicle dynamic model (vehicle-rigid track model). In the rigid track model, only the track irregularities are considered in the track module; the vibrations and deformations of rails, track slab and the foundation are considered in the flexible track model. Taking Chinese CRH3 series wheel profile S1002CN and rail profile CHN60 as examples and considering different track excitations, the two models are compared. The wheel-rail interaction forces, wheel-rail wear depths, wear volumes and vehicle accelerations are chosen as analysis indices for the comparative study.The results show that the wheel-rail forces of the flexible track model are larger than the rigid track model in the frequency range from 70 to 120Hz, while they decrease obviously in the frequency range above 150Hz. The differences in wear depths and volumes between the two models exceed 10%. Therefore, the flexible track model should be considered when studying the match properties of different wheel-rail pairs.
|
|
| 32. |
- Bao, Chunxiong, 1986-, et al.
(författare)
-
A multifunctional display based on photo-responsive perovskite light-emitting diodes
- 2024
-
Ingår i: NATURE ELECTRONICS. - : NATURE PORTFOLIO. - 2520-1131.
-
Tidskriftsartikel (refereegranskat)abstract
- Current display screens are typically only used for information display, but can have a range of different sensors integrated into them for functions such as touch control, ambient light sensing and fingerprint sensing. Photo-responsive light-emitting diodes (LEDs), which can display information and respond to light excitation, could be used to develop future ultra-thin and large screen-to-body ratio screens. However, photo-response is difficult to achieve with conventional display technologies. Here, we report a multifunctional display that uses photo-responsive metal halide perovskite LEDs as pixels. The perovskite LED display can be simultaneously used as a touch screen, ambient light sensor and image sensor (including for fingerprint drawing) without integrating any additional sensors. The light-to-electricity conversion efficiency of the pixels also allow the display to act as a photovoltaic device that can charge the equipment. Photo-responsive metal halide perovskite light-emitting diodes can be used to create a multifunctional display that can function as a touch screen, ambient light sensor and image sensor.
|
|
| 33. |
- Bixby, H., et al.
(författare)
-
Rising rural body-mass index is the main driver of the global obesity epidemic in adults
- 2019
-
Ingår i: Nature. - : Springer Science and Business Media LLC. - 0028-0836 .- 1476-4687. ; 569:7755, s. 260-4
-
Tidskriftsartikel (refereegranskat)abstract
- Body-mass index (BMI) has increased steadily in most countries in parallel with a rise in the proportion of the population who live in cities(.)(1,2) This has led to a widely reported view that urbanization is one of the most important drivers of the global rise in obesity(3-6). Here we use 2,009 population-based studies, with measurements of height and weight in more than 112 million adults, to report national, regional and global trends in mean BMI segregated by place of residence (a rural or urban area) from 1985 to 2017. We show that, contrary to the dominant paradigm, more than 55% of the global rise in mean BMI from 1985 to 2017-and more than 80% in some low- and middle-income regions-was due to increases in BMI in rural areas. This large contribution stems from the fact that, with the exception of women in sub-Saharan Africa, BMI is increasing at the same rate or faster in rural areas than in cities in low- and middle-income regions. These trends have in turn resulted in a closing-and in some countries reversal-of the gap in BMI between urban and rural areas in low- and middle-income countries, especially for women. In high-income and industrialized countries, we noted a persistently higher rural BMI, especially for women. There is an urgent need for an integrated approach to rural nutrition that enhances financial and physical access to healthy foods, to avoid replacing the rural undernutrition disadvantage in poor countries with a more general malnutrition disadvantage that entails excessive consumption of low-quality calories.
|
|
| 34. |
- Chang, Haigang, et al.
(författare)
-
Continuous High Frequency Deep Brain Stimulation of the Rat Anterior Insula Attenuates the Relapse Post Withdrawal and Strengthens the Extinction of Morphine Seeking
- 2020
-
Ingår i: Frontiers in Psychiatry. - : Frontiers Media SA. - 1664-0640. ; 11
-
Tidskriftsartikel (refereegranskat)abstract
- Deep brain stimulation (DBS) modulates the neuronal activity in specific brain circuits and has been recently considered as a promising intervention for refractory addiction. The insula cortex is the hub of interoception and is known to be involved in different aspects of substance use disorder. In the present study, we investigate the effects of continuous high frequency DBS in the anterior insula (AI) on drug-seeking behaviors and examined the molecular mechanisms of DBS action in morphine-addicted rats. Sprague-Dawley rats were trained to the morphine-conditioned place preference (CPP, day 1-8) followed by bilaterally implanted with DBS electrodes in the AI (Day 10) and recovery (Day 10-15). Continuous high-frequency (HF) -DBS (130 Hz, 150 mu A, 90 mu s) was applied during withdrawal (Day 16-30) or extinction sessions. CPP tests were conducted on days 16, 30, 40 during withdrawal session and several rats were used for proteomic analysis on day 30. Following the complete extinction, morphine-CPP was reinstated by a priming dose of morphine infusion (2 mg/kg). The open field and novel objective recognition tests were also performed to evaluate the DBS side effect on the locomotion and recognition memory. Continuous HF-DBS in the AI attenuated the expression of morphine-CPP post-withdrawal (Day 30), but morphine addictive behavior relapsed 10 days after the cessation of DBS (Day 40). Continuous HF-DBS reduced the period to full extinction of morphine-CPP and blocked morphine priming-induced recurrence of morphine addiction. HF-DBS in the AI had no obvious effect on the locomotor activity and novel objective recognition and did not cause anxiety-like behavior. In addition, our proteomic analysis identified eight morphine-regulated proteins in the AI and their expression levels were reversely changed by HF-DBS. Continuous HF-DBS in the bilateral anterior insula prevents the relapse of morphine place preference after withdrawal, facilitates its extinction, blocks the reinstatement induced by morphine priming and reverses the expression of morphine-regulated proteins. Our findings suggest that manipulation of insular activity by DBS could be a potential intervention to treat substance use disorder, although future research is warranted.
|
|
| 35. |
- Chen, Hong, et al.
(författare)
-
PKU-3 : An HCI-Inclusive Aluminoborate for Strecker Reaction Solved by Combining RED and PXRD
- 2015
-
Ingår i: Journal of the American Chemical Society. - : American Chemical Society (ACS). - 0002-7863 .- 1520-5126. ; 137:22, s. 7047-7050
-
Tidskriftsartikel (refereegranskat)abstract
- A novel microporous aluminoborate, denoted as PKU-3, was prepared by the boric acid flux method. The structure of PKU-3 was determined by combining the rotation electron diffraction and synchrotron powder X-ray diffraction data with well resolved ordered Cl- ions in the channel. Composition and crystal structure analysis showed that there are both proton and chlorine ions in the channels. Part of these protons and chlorine ions can be washed away by basic solutions to activate the open pores. The washed PKU-3 can be used as an efficient catalyst in the Strecker reaction with yields higher than 90%.
|
|
| 36. |
- Chen, Peilin, et al.
(författare)
-
Fabrication of a silver nanoparticle-coated collagen membrane with anti-bacterial and anti-inflammatory activities for guided bone regeneration
- 2018
-
Ingår i: Biomedical materials. - 1748-6041. ; 13:6
-
Tidskriftsartikel (refereegranskat)abstract
- Alveolar bone loss is a common problem that affects dental implant placement. A barrier between the bone substitute and gingiva that can prevent fibro-tissue ingrowth, bacterial infection and induce bone formation is a key factor in improving the success of alveolar ridge reconstruction. This study aims to develop a bioactive collagen barrier material for guided bone regeneration, that is coupled with anti-bacterial and anti-inflammatory properties. We have evaluated two silver coating methods and found controllable and precise coating achieved by sonication compared with sputtering. The optimized AgNP-coated collagen membrane exhibited excellent anti-bacterial effects against Staphylococcus aureus (S. aureus) and Pseudomonas aeruginosa (P. aeruginosa) with limited cellular toxicity. It also displayed effective anti-inflammatory effects by reducing the expression and release of inflammatory cytokines including IL-6 and TNF-alpha. Additionally, AgNP-coated collagen membranes were able to induce osteogenic differentiation of mesenchymal stem cells that guide bone regeneration. These findings demonstrate the potential application of AgNP-coated collagen membranes to prevent infection after bone graft introduction in alveolar ridge reconstruction.
|
|
| 37. |
- Chen, Tao, et al.
(författare)
-
Comprehensive applicability evaluation of multi-source snow depth datasets over the Tibetan Plateau
- 2022
-
Ingår i: Journal of Glaciology and Geocryology. - 1000-0240. ; 44:3, s. 795-809
-
Tidskriftsartikel (refereegranskat)abstract
- Snow cover over the Tibetan Plateau has an important impact on the regional climate and water cycle. At present, the existing snow cover datasets have great uncertainty across this region, so the applicability assessment is indispensable in order to make best use of the advantages and bypass the disadvantages. In this study, a comprehensive quantitative evaluation of multiple variables and multiple evaluation indicators was carried out for three snow depth datasets over the Tibetan Plateau against the meteorological station observations（OBS）. The three snow depth datasets include one passive microwave remote sensing dataset（CHE）and two reanalysis datasets（ERA5-Land and MERRA2）. The variables are the annual mean snow depth, the annual maximum snow depth, and the annual snow cover days. In addition, the evaluation indicators are seasonal cycle, climatology, maximum value, standard deviation, interannual variation, and trend. A rank score（RS）value of 0~1 is computed for each evaluation indicator of each variable, the larger value of RS indicate relatively better performance of a snow depth dataset. Assessment results imply that, comprehensively considered, MERRA2 exhibits best agreement with OBS, followed by ERA5-Land, and finally CHE. Evaluate based on the RS of each variable, MERRA2 shows better performance on annual maximum snow depth and annual snow cover days, CHE shows better performance on annual mean snow depth. Evaluate based on the RS of each evaluation indicator, CHE shows advantages in describing trend, ERA5-Land exhibits better agreement with OBS on interannual variation, and MERRA2 show better performance on the rest of the indicators including seasonal cycle, climatology, maximum value and standard deviation. The RS statistics in terms of regional average and spatial distribution show that CHE performs better in the former, and ERA5-Land performs better in the latter. On the other hand, there are obvious deficiencies in all three snow depth datasets. MERRA2 has insufficient ability to characterize the interdecadal variation in snow cover, and its qualitative results for trend in snow cover is inconsistent with OBS, the reason for the first deficiency needs to be further studied and the second deficiency may be mainly related to its simulation capability to precipitation trend. ERA5-Land significantly overestimates the snow cover over the Tibetan Plateau, this may be mostly related to its data assimilation scheme. CHE has poor ability to characterize the spatial distribution of snow cover, coarse spatial resolution of passive microwave remote sensing may be the main reason. The conclusions are only applicable to the central and eastern part of the Tibetan Plateau due to the scarcity of meteorological station in west part of the Tibetan Plateau. Based on the remote sensing and reanalysis data, there is great uncertainty in the trend of snow cover in the western part of the Tibetan Plateau. These systematic classification evaluation of the three representative snow depth datasets provides information on data selection and data refinement.
|
|
| 38. |
- Chen, Zhishan, et al.
(författare)
-
Fine-mapping analysis including over 254 000 East Asian and European descendants identifies 136 putative colorectal cancer susceptibility genes
- 2024
-
Ingår i: Nature Communications. - : Springer Nature. - 2041-1723. ; 15:1
-
Tidskriftsartikel (refereegranskat)abstract
- Genome-wide association studies (GWAS) have identified more than 200 common genetic variants independently associated with colorectal cancer (CRC) risk, but the causal variants and target genes are mostly unknown. We sought to fine-map all known CRC risk loci using GWAS data from 100,204 cases and 154,587 controls of East Asian and European ancestry. Our stepwise conditional analyses revealed 238 independent association signals of CRC risk, each with a set of credible causal variants (CCVs), of which 28 signals had a single CCV. Our cis-eQTL/mQTL and colocalization analyses using colorectal tissue-specific transcriptome and methylome data separately from 1299 and 321 individuals, along with functional genomic investigation, uncovered 136 putative CRC susceptibility genes, including 56 genes not previously reported. Analyses of single-cell RNA-seq data from colorectal tissues revealed 17 putative CRC susceptibility genes with distinct expression patterns in specific cell types. Analyses of whole exome sequencing data provided additional support for several target genes identified in this study as CRC susceptibility genes. Enrichment analyses of the 136 genes uncover pathways not previously linked to CRC risk. Our study substantially expanded association signals for CRC and provided additional insight into the biological mechanisms underlying CRC development.
|
|
| 39. |
- Chen, Zhi, et al.
(författare)
-
Large-Area Crystalline Zeolitic Imidazolate Framework Thin Films
- 2021
-
Ingår i: Angewandte Chemie International Edition. - : Wiley. - 1433-7851 .- 1521-3773. ; 60:25, s. 14124-14130
-
Tidskriftsartikel (refereegranskat)abstract
- We report that continuous MOF films with highly controlled thickness (from 44 to 5100 nm) can be deposited over length scales greater than 80 centimeters by a facile, fast, and cost-effective spray-coating method. Such success relies on our discovery of unprecedented perfectly dispersed colloidal solutions consisting of amorphous MOF nanoparticles, which we adopted as precursors that readily converted to the crystalline films upon low-temperature in situ heating. The colloidal solutions allow for the fabrication of compact and uniform MOF films on a great deal of substrates such as fluorine-doped tin oxide, glass, SiO2, Al2O3, Si, Cu, and even flexible polycarbonate, widening their technological applications where substrates are essential. Despite the present work focuses on the fabrication of uniform cobalt-(2-methylimidazole)2 and zinc-(2-methylimidazole)2 films, our findings mark a great possibility in producing other high-quality MOF thin films on a large scale.
|
|
| 40. |
- Cheng, Shi-Ping, et al.
(författare)
-
Haplotype-resolved genome assembly and allele-specific gene expression in cultivated ginger
- 2021
-
Ingår i: Horticulture Research. - : Springer Nature. - 2052-7276. ; 8:1
-
Tidskriftsartikel (refereegranskat)abstract
- Ginger (Zingiber officinale) is one of the most valued spice plants worldwide; it is prized for its culinary and folk medicinal applications and is therefore of high economic and cultural importance. Here, we present a haplotype-resolved, chromosome-scale assembly for diploid ginger anchored to 11 pseudochromosome pairs with a total length of 3.1 Gb. Remarkable structural variation was identified between haplotypes, and two inversions larger than 15 Mb on chromosome 4 may be associated with ginger infertility. We performed a comprehensive, spatiotemporal, genome-wide analysis of allelic expression patterns, revealing that most alleles are coordinately expressed. The alleles that exhibited the largest differences in expression showed closer proximity to transposable elements, greater coding sequence divergence, more relaxed selection pressure, and more transcription factor binding site differences. We also predicted the transcription factors potentially regulating 6-gingerol biosynthesis. Our allele-aware assembly provides a powerful platform for future functional genomics, molecular breeding, and genome editing in ginger.
|
|
| 41. |
- Cui, Yong, et al.
(författare)
-
Accurate photovoltaic measurement of organic cells for indoor applications
- 2021
-
Ingår i: Joule. - : CELL PRESS. - 2542-4351. ; 5:5, s. 1016-1023
-
Tidskriftsartikel (övrigt vetenskapligt/konstnärligt)abstract
- Photovoltaic (PV) cells offer a convenient energy source to drive micropower electronic devices for indoor applications. However, it is challenging to measure the power conversion efficiency (PCE) of PV cells under indoor lighting and the PV community lacks a feasible and accurate measurement protocol. Here, we start with the fundamental parameters which determine the PCE, and carefully design a series of experiments to examine the origins which might cause measurement errors for organic PV measurements under indoor lighting. We demonstrate the critical importance of: 1, temporal stability and spatial homogeneity of the light sources, 2, calibration of the spectral irradiance and illuminations of the light sources, 3, the area of the cells (1 cm2 or large cells are preferred), 4, the aperture of the mask (an aperture slightly smaller than the cell area is preferred), and 5, stray lights from the measurement environment. Based on these careful investigations, we suggest a feasible measurement method, by which accurate measurement of the indoor PV efficiency is made possible. Our study will promote the healthy development of indoor PV technology for practical applications.
|
|
| 42. |
- Cui, Yong, et al.
(författare)
-
Over 16% efficiency organic photovoltaic cells enabled by a chlorinated acceptor with increased open-circuit voltages
- 2019
-
Ingår i: Nature Communications. - : NATURE PUBLISHING GROUP. - 2041-1723. ; 10
-
Tidskriftsartikel (refereegranskat)abstract
- Broadening the optical absorption of organic photovoltaic (OPV) materials by enhancing the intramolecular push-pull effect is a general and effective method to improve the power conversion efficiencies of OPV cells. However, in terms of the electron acceptors, the most common molecular design strategy of halogenation usually results in down-shifted molecular energy levels, thereby leading to decreased open-circuit voltages in the devices. Herein, we report a chlorinated non-fullerene acceptor, which exhibits an extended optical absorption and meanwhile displays a higher voltage than its fluorinated counterpart in the devices. This unexpected phenomenon can be ascribed to the reduced non-radiative energy loss (0.206 eV). Due to the simultaneously improved short-circuit current density and open-circuit voltage, a high efficiency of 16.5% is achieved. This study demonstrates that finely tuning the OPV materials to reduce the bandgap-voltage offset has great potential for boosting the efficiency.
|
|
| 43. |
- Cui, Yong, et al.
(författare)
-
Single-Junction Organic Photovoltaic Cells with Approaching 18% Efficiency
- 2020
-
Ingår i: Advanced Materials. - : WILEY-V C H VERLAG GMBH. - 0935-9648 .- 1521-4095. ; 32:19
-
Tidskriftsartikel (refereegranskat)abstract
- Optimizing the molecular structures of organic photovoltaic (OPV) materials is one of the most effective methods to boost power conversion efficiencies (PCEs). For an excellent molecular system with a certain conjugated skeleton, fine tuning the alky chains is of considerable significance to fully explore its photovoltaic potential. In this work, the optimization of alkyl chains is performed on a chlorinated nonfullerene acceptor (NFA) named BTP-4Cl-BO (a Y6 derivative) and very impressive photovoltaic parameters in OPV cells are obtained. To get more ordered intermolecular packing, the n-undecyl is shortened at the edge of BTP-eC11 to n-nonyl and n-heptyl. As a result, the NFAs of BTP-eC9 and BTP-eC7 are synthesized. The BTP-eC7 shows relatively poor solubility and thus limits its application in device fabrication. Fortunately, the BTP-eC9 possesses good solubility and, at the same time, enhanced electron transport property than BTP-eC11. Significantly, due to the simultaneously enhanced short-circuit current density and fill factor, the BTP-eC9-based single-junction OPV cells record a maximum PCE of 17.8% and get a certified value of 17.3%. These results demonstrate that minimizing the alkyl chains to get suitable solubility and enhanced intermolecular packing has a great potential in further improving its photovoltaic performance.
|
|
| 44. |
|
|
| 45. |
- Dorschel, Boris, et al.
(författare)
-
The International Bathymetric Chart of the Southern Ocean Version 2
- 2022
-
Ingår i: Scientific Data. - : Springer Science and Business Media LLC. - 2052-4463. ; 9:1
-
Tidskriftsartikel (refereegranskat)abstract
- The Southern Ocean surrounding Antarctica is a region that is key to a range of climatic and oceanographic processes with worldwide effects, and is characterised by high biological productivity and biodiversity. Since 2013, the International Bathymetric Chart of the Southern Ocean (IBCSO) has represented the most comprehensive compilation of bathymetry for the Southern Ocean south of 60 degrees S. Recently, the IBCSO Project has combined its efforts with the Nippon Foundation - GEBCO Seabed 2030 Project supporting the goal of mapping the world's oceans by 2030. New datasets initiated a second version of IBCSO (IBCSO v2). This version extends to 50 degrees S (covering approximately 2.4 times the area of seafloor of the previous version) including the gateways of the Antarctic Circumpolar Current and the Antarctic circumpolar frontal systems. Due to increased (multibeam) data coverage, IBCSO v2 significantly improves the overall representation of the Southern Ocean seafloor and resolves many submarine landforms in more detail. This makes IBCSO v2 the most authoritative seafloor map of the area south of 50 degrees S.
|
|
| 46. |
- Du, Hao, et al.
(författare)
-
Recovery of lithium salt from spent lithium-ion battery by less polar solvent wash and water extraction
- 2023
-
Ingår i: Carbon Neutralization. - : John Wiley & Sons. - 2769-3325 .- 2769-3325. ; 2:4, s. 416-424
-
Tidskriftsartikel (refereegranskat)abstract
- The lithium hexafluorophosphate (LiPF6) in spent lithium-ion batteries (LIBs) is a potentially valuable resource and a significant environmental pollutant. Unfortunately, most of the LiPF6 in a spent LIB is difficult to extract because the electrolyte is strongly adsorbed by the cathode, anode, and separator. Storing extracted electrolyte is also challenging because it contains LiPF6, which promotes the decomposition of the solvent. Here we show that electrolytes in spent LIBs can be collected by a less polar solvent dimethyl carbonate (DMC) wash, and LiPF6 can be concentrated by simple aqueous extraction by lowering ethylene carbonate (EC) content in the recycled electrolyte. Due to the similar dielectric constant of EC and water, reducing the content of EC in LIB electrolytes, or even eliminating it, facilitates the separation of water and electrolyte, thus enabling the lithium salts in the electrolyte to be separated from the organic solvent. The lithium salt extracting efficiency achieved in this way can be as high as 99.8%, and fluorine and phosphorus of LiPF6 can be fixed in the form of stable metal fluoride and phosphate by hydrothermal method. The same strategy can be used in industrial waste electrolyte recycling by diluting the waste with DMC and extracting the resulting solution with water. This work thus reveals a new route for waste electrolyte treatment and will also support the development of advanced EC-free electrolytes for high-performance, safe, and easily recyclable LIBs.
|
|
| 47. |
|
|
| 48. |
- Du, QQ, et al.
(författare)
-
Generation of mega brown adipose tissue in adults by controlling brown adipocyte differentiation in vivo
- 2022
-
Ingår i: Proceedings of the National Academy of Sciences of the United States of America. - : Proceedings of the National Academy of Sciences. - 1091-6490. ; 119:40, s. e2203307119-
-
Tidskriftsartikel (refereegranskat)abstract
- Brown adipose tissue (BAT) is a highly specialized adipose tissue in its immobile location and size during the entire adulthood. In response to cold exposure and other β3-adrenoreceptor stimuli, BAT commits energy consumption by nonshivering thermogenesis (NST). However, the molecular machinery in controlling the BAT mass in adults is unknown. Here, we show our surprising findings that the BAT mass and functions can be manipulated in adult animals by controlling BAT adipocyte differentiation in vivo. Platelet-derived growth factor receptor α (PDGFα) expressed in BAT progenitor cells served a signaling function to avert adipose progenitor differentiation. Genetic and pharmacological loss-of-function of PDGFRα eliminated the differentiation barrier and permitted progenitor cell differentiation to mature and functional BAT adipocytes. Consequently, an enlarged BAT mass (megaBAT) was created by PDGFRα inhibition owing to increases of brown adipocyte numbers. Under cold exposure, a microRNA-485 (miR-485) was identified as a master suppressor of the PDGFRα signaling, and delivery of miR-485 also produced megaBAT in adult animals. Noticeably, megaBAT markedly improved global metabolism, insulin sensitivity, high-fat-diet (HFD)-induced obesity, and diabetes by enhancing NST. Together, our findings demonstrate that the adult BAT mass can be increased by blocking the previously unprecedented inhibitory signaling for BAT progenitor cell differentiation. Thus, blocking the PDGFRα for the generation of megaBAT provides an attractive strategy for treating obesity and type 2 diabetes mellitus (T2DM).
|
|
| 49. |
- Fan, Qunping, 1989, et al.
(författare)
-
High-performance all-polymer solar cells enabled by a novel low bandgap non-fully conjugated polymer acceptor
- 2021
-
Ingår i: Science in China Series B. - : Springer Nature. - 1674-7291 .- 1869-1870. ; 64, s. 1380-1388
-
Tidskriftsartikel (refereegranskat)abstract
- Anon-fully conjugated polymer as a new class of acceptor materials has shown some advantages over its small molecular counterpart when used in photoactive layers for all-polymer solar cells (all-PSCs), despite a low power conversion efficiency (PCE) caused by its narrow absorption spectra. Herein, a novel non-fully conjugated polymer acceptor PFY-2TS with a low bandgap of similar to 1.40 eV was developed, via polymerizing a large pi-fused small molecule acceptor (SMA) building block (namely YBO) with a non-conjugated thioalkyl linkage. Compared with its precursor YBO, PFY-2TS retains a similar low bandgap but a higher LUMO level. Moreover, compared with the structural analog of YBO-based fully conjugated polymer acceptor PFY-DTC, PFY-2TS shows similar absorption spectrum and electron mobility, but significantly different molecular crystallinity and aggregation properties, which results in optimal blend morphology with a polymer donor PBDB-T and better device physical processes in all-PSCs. As a result, PFY-2TS-based all-PSCs achieved a PCE of 12.31% with a small energy loss of 0.56 eV enabled by the reduced non-radiative energy loss (0.24 eV), which is better than that of 11.08% for the PFY-DTC-based ones. Our work clearly demonstrated that non-fully conjugated polymers as a new class of acceptor materials are very promising for the development of high-performance all-PSCs.
|
|
| 50. |
- Finegan, Donal P., et al.
(författare)
-
Spatial dynamics of lithiation and lithium plating during high-rate operation of graphite electrodes
- 2020
-
Ingår i: Energy and Environmental Science. - : Royal Society of Chemistry (RSC). - 1754-5692 .- 1754-5706. ; 13:8, s. 2570-2584
-
Tidskriftsartikel (refereegranskat)abstract
- The principal inhibitor of fast charging lithium ion cells is the graphite negative electrode, where favorable conditions for lithium plating occur at high charge rates, causing accelerated degradation and safety concerns. The local response of graphite, both at the electrode and particle level, when exposed to fast charging conditions of around 6C is not well understood. Consequently, the conditions that lead to the onset of lithium plating, as well as the local dynamics of lithium plating and stripping, have also remained elusive. Here, we use high-speed (100 Hz) pencil-beam X-ray diffraction to repeatedly raster along the depth of a 101 µm thick graphite electrode in 3 µm steps during fast (up to 6C) charge and discharge conditions. Consecutive depth profiles from separator to current collector were each captured in 0.5 seconds, giving an unprecedented spatial and temporal description of the state of the electrode and graphite's staging dynamics during high rate conditions. The electrode is preferentially activated near the separator, and the non-uniformity increases with rate and is influenced by free-energy barriers between graphite's lithiation stages. The onset of lithium plating and stripping was quantified, occurring only within the first 15 µm from the separator. The presence of lithium plating changed the behavior of the underlying graphite, such as causing co-existence of LiC6 and graphite in the fully discharged state. Finally, the staging behavior of graphite at different rates was quantified, revealing a high dependency on rate and drastic hysteresis between lithiation and delithiation.
|
|
