| 1. |
|
|
| 2. |
- Herstad-Svärd, S., et al.
(författare)
-
Ramprogram – Åtgärder för samtidig minimering av alkalirelaterade driftproblem, Etapp 2
- 2007
-
Rapport (övrigt vetenskapligt/konstnärligt)abstract
- Combustion of an increasing amount of biofuel and waste woods has resulted in certainenvironmental advantages, including decreased emissions of fossil CO2, SO2 andmetals. On the other hand, a number of chloride and alkali related operational problemshave occurred which are related to combustion of these fuels.Alkali related operational problems have been studied in a project consisting of twoparts. The overall scope has been to characterise the operational problems and to studymeasures to minimise them. The first part was reported in Värmeforsk report 997 wherethe results were summarised in a table of different measures. In part two, additionalmeasures have been included in the test plan and initial corrosion has been studiedlinked to the different measures. The tests have also in part two been carried out at the12 MW CFB boiler at Chalmers. The effect of the selected measures has beeninvestigated concerning both deposit formation and bed agglomeration, and at the sametime emissions and other operational conditions were characterised.The second part of the project has among other things focused on:• To investigate measures which decrease the content of alkali and chloride in thedeposits, and consequently decrease the risk for corrosion (by investigating theinitial corrosion). Focus was also on trying to explain favourable effects.• To investigate if it is possible to combine a rather low dosage of kaolin and injectionof ammonium sulphate. This was done in order to reduce both bed agglomerationand problems from deposits during combustion of fuels rich in chlorine.• To investigate if co-combustion with sewage sludge, de-inking sludge or peat withhigh ash content, could give similar advantages as conventional additives.• Investigate if ash from PFBC is possible to use as an alternative bed material.By comparing the different measures in part two, it could be concluded that cocombustionof sewage sludge gave the best overall effect. The judgement was based onthe effects concerning bed agglomeration, level of alkali chloride in the flue gas,deposits and initial corrosion. Simultaneous addition of kaolin and ammonia sulphatealso had a favourable impact both in the bed and on the alkali chlorides in the gas phase.Dosage of kaolin did not reduce the effect of injected ammonium sulphate. Cocombustionof peat could also be a very attractive alternative, but it is critical to select asuitable peat type. It is of special concern to avoid peat with a high content of calcium,since it can increase the level of alkali chlorides by reacting with available sulphur.Change of bed material to ash from PFBC can decrease problems with bedagglomeration, but there is a risk of increased deposit formation and corrosion. A boileroperated with high steam data should consequently combine the change of bed materialwith injection of ammonium sulphate or another source of sulphur.Co-combustion of de-inking sludge from pulp and paper production can reduceproblems with bed agglomeration. There is, however, an increased chance of corrosiondue to the high content of calcium. Injection of sulphates may improve the situationconcerning corrosion. The results also showed that low potassium chlorine content in the flue gas decreasesthe risk of corrosion. Increased amount of potassium chlorine content in the flue gaswill not necessary give a high amount of chlorine content in the deposits if there is sulphur in the system.Key words: agglomeration, deposits, corrosion, alkali, kaolin, ammonium sulphate,sludge
|
|
| 3. |
- Kassman, H., et al.
(författare)
-
Influence of air-staging on the concentration profiles of NH3 and HCN in the combustion chamber of a CFB boiler burning coal
- 1999
-
Ingår i: 15th Int. Conf. on Fluidized Bed Combustion / Reuther, R.B..
-
Konferensbidrag (refereegranskat)abstract
- The characterisation of the concentration profiles of NH3 and HCN are of great importance for increasing the knowledge of the formation and destruction pathways of NO and N2O in a fluidized bed boiler. Further improvements of the sampling methods for the determination of both NH3 and HCN in the combustion chamber in full-scale CFB boilers are also needed. A gas-sampling probe connected to a Fourier Transform Infra Red (FTIR) instrument and a gas-quenching (GQ) probe in which the sample is quenched directly in the probe tip by a circulating trapper solution were used. The FTIR technique is based on analysis of hot combustion gases, whereas the trapper solutions from the GQ probe were analysed by means of wet chemistry.The tests were performed during coal combustion in a 12 MW CFB boiler, which was operated at three air-staging cases with the addition of limestone for sulphur capture. The concentration profiles of NH3 and HCN in the combustion chamber showed a different pattern concerning the influence of air-staging. The highest levels of NH3 were observed during reducing conditions (severe air-staging), and the lowest were found under oxidising conditions (no air-staging). The levels of HCN were much lower than those measured for NH3. The highest levels of HCN were observed for reversed air-staging and severe air-staging showed almost no HCN. The potential reactions involving NH3 and HCN in the combustion chamber as well as the potential measurement errors in each sampling technique are discussed for the three air-staging cases.
|
|
| 4. |
|
|
| 5. |
- Öberg, Å., et al.
(författare)
-
Conductive nanocomposite ceramics as tribological and electrical contact materials
- 2010
-
Ingår i: European Physical Journal. - : EDP Sciences. - 1286-0042 .- 1286-0050. ; 49:2, s. 22902-
-
Tidskriftsartikel (refereegranskat)abstract
- Conductive ceramics have widespread use in many industrial applications. One important application for such materials is electrical contact technology. Over the last few years, a new class of nanocomposite ceramic thin film materials has been developed with contact coatings as one key objective. This family of materials has proven to combine the favorable contact properties of metals, such as low electrical and thermal resistivity, and high ductility, with those of ceramics such as low friction and wear rate, high chemical integrity and good high-temperature properties. Furthermore, it is also found that the tribological properties of such materials can be tailored by alloying thus creating a triboactive system. The technology is now industrialized, and a practical example of a contact system utilizing a nanocomposite coating for improved performance is given.
|
|
