| 1. |
- Meyer, H.F., et al.
(författare)
-
Overview of physics studies on ASDEX Upgrade
- 2019
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 59:11
-
Forskningsöversikt (refereegranskat)abstract
- The ASDEX Upgrade (AUG) programme, jointly run with the EUROfusion MST1 task force, continues to significantly enhance the physics base of ITER and DEMO. Here, the full tungsten wall is a key asset for extrapolating to future devices. The high overall heating power, flexible heating mix and comprehensive diagnostic set allows studies ranging from mimicking the scrape-off-layer and divertor conditions of ITER and DEMO at high density to fully non-inductive operation (q 95 = 5.5, ) at low density. Higher installed electron cyclotron resonance heating power 6 MW, new diagnostics and improved analysis techniques have further enhanced the capabilities of AUG. Stable high-density H-modes with MW m-1 with fully detached strike-points have been demonstrated. The ballooning instability close to the separatrix has been identified as a potential cause leading to the H-mode density limit and is also found to play an important role for the access to small edge-localized modes (ELMs). Density limit disruptions have been successfully avoided using a path-oriented approach to disruption handling and progress has been made in understanding the dissipation and avoidance of runaway electron beams. ELM suppression with resonant magnetic perturbations is now routinely achieved reaching transiently . This gives new insight into the field penetration physics, in particular with respect to plasma flows. Modelling agrees well with plasma response measurements and a helically localised ballooning structure observed prior to the ELM is evidence for the changed edge stability due to the magnetic perturbations. The impact of 3D perturbations on heat load patterns and fast-ion losses have been further elaborated. Progress has also been made in understanding the ELM cycle itself. Here, new fast measurements of and E r allow for inter ELM transport analysis confirming that E r is dominated by the diamagnetic term even for fast timescales. New analysis techniques allow detailed comparison of the ELM crash and are in good agreement with nonlinear MHD modelling. The observation of accelerated ions during the ELM crash can be seen as evidence for the reconnection during the ELM. As type-I ELMs (even mitigated) are likely not a viable operational regime in DEMO studies of 'natural' no ELM regimes have been extended. Stable I-modes up to have been characterised using -feedback. Core physics has been advanced by more detailed characterisation of the turbulence with new measurements such as the eddy tilt angle - measured for the first time - or the cross-phase angle of and fluctuations. These new data put strong constraints on gyro-kinetic turbulence modelling. In addition, carefully executed studies in different main species (H, D and He) and with different heating mixes highlight the importance of the collisional energy exchange for interpreting energy confinement. A new regime with a hollow profile now gives access to regimes mimicking aspects of burning plasma conditions and lead to nonlinear interactions of energetic particle modes despite the sub-Alfvénic beam energy. This will help to validate the fast-ion codes for predicting ITER and DEMO.
|
|
| 2. |
- Stroth, U., et al.
(författare)
-
Progress from ASDEX Upgrade experiments in preparing the physics basis of ITER operation and DEMO scenario development
- 2022
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 62:4
-
Tidskriftsartikel (refereegranskat)abstract
- An overview of recent results obtained at the tokamak ASDEX Upgrade (AUG) is given. A work flow for predictive profile modelling of AUG discharges was established which is able to reproduce experimental H-mode plasma profiles based on engineering parameters only. In the plasma center, theoretical predictions on plasma current redistribution by a dynamo effect were confirmed experimentally. For core transport, the stabilizing effect of fast ion distributions on turbulent transport is shown to be important to explain the core isotope effect and improves the description of hollow low-Z impurity profiles. The L-H power threshold of hydrogen plasmas is not affected by small helium admixtures and it increases continuously from the deuterium to the hydrogen level when the hydrogen concentration is raised from 0 to 100%. One focus of recent campaigns was the search for a fusion relevant integrated plasma scenario without large edge localised modes (ELMs). Results from six different ELM-free confinement regimes are compared with respect to reactor relevance: ELM suppression by magnetic perturbation coils could be attributed to toroidally asymmetric turbulent fluctuations in the vicinity of the separatrix. Stable improved confinement mode plasma phases with a detached inner divertor were obtained using a feedback control of the plasma β. The enhanced D α H-mode regime was extended to higher heating power by feedback controlled radiative cooling with argon. The quasi-coherent exhaust regime was developed into an integrated scenario at high heating power and energy confinement, with a detached divertor and without large ELMs. Small ELMs close to the separatrix lead to peeling-ballooning stability and quasi continuous power exhaust. Helium beam density fluctuation measurements confirm that transport close to the separatrix is important to achieve the different ELM-free regimes. Based on separatrix plasma parameters and interchange-drift-Alfvén turbulence, an analytic model was derived that reproduces the experimentally found important operational boundaries of the density limit and between L- and H-mode confinement. Feedback control for the X-point radiator (XPR) position was established as an important element for divertor detachment control. Stable and detached ELM-free phases with H-mode confinement quality were obtained when the XPR was moved 10 cm above the X-point. Investigations of the plasma in the future flexible snow-flake divertor of AUG by means of first SOLPS-ITER simulations with drifts activated predict beneficial detachment properties and the activation of an additional strike point by the drifts.
|
|
| 3. |
- Aaltonen, T., et al.
(författare)
-
Combination of CDF and D0 measurements of the W boson helicity in top quark decays
- 2012
-
Ingår i: Physical Review D. - 1550-7998 .- 1550-2368. ; 85:7, s. 071106-
-
Tidskriftsartikel (refereegranskat)abstract
- We report the combination of recent measurements of the helicity of the W boson from top quark decay by the CDF and D0 collaborations, based on data samples corresponding to integrated luminosities of 2.7-5.4 fb(-1) of p (p) over bar collisions collected during Run II of the Fermilab Tevatron collider. Combining measurements that simultaneously determine the fractions of W bosons with longitudinal (f(0)) and right-handed (f(+)) helicities, we find f(0) = 0.722 +/- 0.081[+/- 0.062(stat) +/- 0.052(syst)] and f(+) = -0.033 +/- 0.046[+/- 0.034(stat) +/- 0.031(syst)]. Combining measurements where one of the helicity fractions is fixed to the value expected in the standard model, we find f(0) = 0.682 +/- 0.057[+/- 0.035(stat) +/- 0.046(syst)] for fixed f(+) and f(+) = -0.015 +/- 0.035[+/- 0.018(stat) +/- 0.030(syst)] for fixed f(0). The results are consistent with standard model expectations.
|
|
| 4. |
- Aaltonen, T., et al.
(författare)
-
Combination of CDF and D0 W-Boson mass measurements
- 2013
-
Ingår i: Physical Review D. - 1550-7998 .- 1550-2368. ; 88:5, s. 052018-
-
Tidskriftsartikel (refereegranskat)abstract
- We summarize and combine direct measurements of the mass of the W boson in root s = 1.96 TeV proton-antiproton collision data collected by CDF and D0 experiments at the Fermilab Tevatron Collider. Earlier measurements from CDF and D0 are combined with the two latest, more precise measurements: a CDF measurement in the electron and muon channels using data corresponding to 2.2 fb(-1) of integrated luminosity, and a D0 measurement in the electron channel using data corresponding to 4.3 fb(-1) of integrated luminosity. The resulting Tevatron average for the mass of the W boson is M-W = 80387 +/- 16 MeV. Including measurements obtained in electron-positron collisions at LEP yields the most precise value of M-W = 80385 +/- 15 MeV.
|
|
| 5. |
- Aaltonen, T., et al.
(författare)
-
Combination of measurements of the top-quark pair production cross section from the Tevatron Collider
- 2014
-
Ingår i: Physical Review D. - 1550-7998 .- 1550-2368. ; 89:7
-
Tidskriftsartikel (refereegranskat)abstract
- We combine six measurements of the inclusive top-quark pair (t(sic)) production cross section (sigma(t)(sic)) from data collected with the CDF and D0 detectors at the Fermilab Tevatron with proton-antiproton collisions at root s = 1.96 TeV. The data correspond to integrated luminosities of up to 8.8 fb(-1). We obtain a value of sigma tt = 7.60 +/- 0.41 pb for a top-quark mass of m(t) = 172.5 GeV. The contributions to the uncertainty are 0.20 pb from statistical sources, 0.29 pb from systematic sources, and 0.21 pb from the uncertainty on the integrated luminosity. The result is in good agreement with the standard model expectation of 7.35(-0.33)(+0.28) pb at next-to-next-to-leading order and next-to-next-to leading logarithms in perturbative QCD.
|
|
| 6. |
- Aaltonen, T., et al.
(författare)
-
Combination of Tevatron Searches for the Standard Model Higgs Boson in the W+W- Decay Mode
- 2010
-
Ingår i: Physical Review Letters. - 0031-9007 .- 1079-7114. ; 104:6, s. 061802-
-
Tidskriftsartikel (refereegranskat)abstract
- We combine searches by the CDF and D0 Collaborations for a Higgs boson decaying to W+W-. The data correspond to an integrated total luminosity of 4.8 (CDF) and 5.4 (D0) fb(-1) of p (p) over bar collisions at root s = 1.96 TeV at the Fermilab Tevatron collider. No excess is observed above background expectation, and resulting limits on Higgs boson production exclude a standard model Higgs boson in the mass range 162-166 GeV at the 95% C.L.
|
|
| 7. |
- Aaltonen, T., et al.
(författare)
-
Evidence for a Particle Produced in Association with Weak Bosons and Decaying to a Bottom-Antibottom Quark Pair in Higgs Boson Searches at the Tevatron
- 2012
-
Ingår i: Physical Review Letters. - 0031-9007 .- 1079-7114. ; 109:7, s. 071804-
-
Tidskriftsartikel (refereegranskat)abstract
- We combine searches by the CDF and D0 Collaborations for the associated production of a Higgs boson with a W or Z boson and subsequent decay of the Higgs boson to a bottom-antibottom quark pair. The data, originating from Fermilab Tevatron p (p) over bar collisions at root s = 1.96 TeV, correspond to integrated luminosities of up to 9.7 fb(-1). The searches are conducted for a Higgs boson with mass in the range 100-150 GeV/c(2). We observe an excess of events in the data compared with the background predictions, which is most significant in the mass range between 120 and 135 GeV/c(2). The largest local significance is 3.3 standard deviations, corresponding to a global significance of 3.1 standard deviations. We interpret this as evidence for the presence of a new particle consistent with the standard model Higgs boson, which is produced in association with a weak vector boson and decays to a bottom-antibottom quark pair.
|
|
| 8. |
- Aaltonen, T., et al.
(författare)
-
Higgs boson studies at the Tevatron
- 2013
-
Ingår i: Physical Review D. - 1550-7998 .- 1550-2368. ; 88:5, s. 052014-
-
Tidskriftsartikel (refereegranskat)abstract
- We combine searches by the CDF and D0 Collaborations for the standard model Higgs boson with mass in the range 90-200 GeV/c(2) produced in the gluon-gluon fusion, WH, ZH, t (t) over barH, and vector boson fusion processes, and decaying in the H -> b (b) over bar, H -> W+W-, H -> ZZ, H -> tau(+)tau(-), and H -> gamma gamma modes. The data correspond to integrated luminosities of up to 10 fb(-1) and were collected at the Fermilab Tevatron in p (p) over bar collisions at root s = 1.96 TeV. The searches are also interpreted in the context of fermiophobic and fourth generation models. We observe a significant excess of events in the mass range between 115 and 140 GeV/c(2). The local significance corresponds to 3.0 standard deviations at m(H) = 125 GeV/c(2), consistent with the mass of the Higgs boson observed at the LHC, and we expect a local significance of 1.9 standard deviations. We separately combine searches for H -> b (b) over bar, H -> W+W-, H -> tau(+)tau(-), and H -> gamma gamma. The observed signal strengths in all channels are consistent with the presence of a standard model Higgs boson with a mass of 125 GeV/c(2).
|
|
| 9. |
- Aaltonen, T., et al.
(författare)
-
Observation of s-Channel Production of Single Top Quarks at the Tevatron
- 2014
-
Ingår i: Physical Review Letters. - 0031-9007 .- 1079-7114. ; 112:23
-
Tidskriftsartikel (refereegranskat)abstract
- We report the first observation of single-top-quark production in the s channel through the combination of the CDF and D0 measurements of the cross section in proton-antiproton collisions at a center-of-mass energy of 1.96 TeV. The data correspond to total integrated luminosities of up to 9.7 fb(-1) per experiment. The measured cross section is sigma(s) = 1.29(-0.24)(+0.26) pb. The probability of observing a statistical fluctuation of the background to a cross section of the observed size or larger is 1.8 x 10(-10), corresponding to a significance of 6.3 standard deviations for the presence of an s-channel contribution to the production of single-top quarks.
|
|
| 10. |
- Aaltonen, T., et al.
(författare)
-
Tevatron Combination of Single-Top-Quark Cross Sections and Determination of the Magnitude of the Cabibbo-Kobayashi-Maskawa Matrix Element V-tb
- 2015
-
Ingår i: Physical Review Letters. - 0031-9007 .- 1079-7114. ; 115:15
-
Tidskriftsartikel (refereegranskat)abstract
- We present the final combination of CDF and D0 measurements of cross sections for single-top-quark production in proton-antiproton collisions at a center-of-mass energy of 1.96 TeV. The data correspond to total integrated luminosities of up to 9.7 fb(-1) per experiment. The t-channel cross section is measured to be sigma(t) = 2.25(-0.31)(+0.29) pb. We also present the combinations of the two-dimensional measurements of the s- vs t-channel cross section. In addition, we give the combination of the s + t channel cross section measurement resulting in sigma(s+t) = 3.30(-0.40)(+0.52) pb, without assuming the standard model value for the ratio sigma(s)/sigma(t). The resulting value of the magnitude of the top-to-bottom quark coupling is vertical bar V-tb vertical bar = 1.02(-0.05)(+0.06), corresponding to vertical bar V-tb vertical bar > 0.92 at the 95% C. L.
|
|
| 11. |
- Aaltonen, T., et al.
(författare)
-
Tevatron Constraints on Models of the Higgs Boson with Exotic Spin and Parity Using Decays to Bottom-Antibottom Quark Pairs
- 2015
-
Ingår i: Physical Review Letters. - 0031-9007 .- 1079-7114. ; 114:15
-
Tidskriftsartikel (refereegranskat)abstract
- Combined constraints from the CDF and D0 Collaborations on models of the Higgs boson with exotic spin J and parity P are presented and compared with results obtained assuming the standard model value J(P) = 0(+). Both collaborations analyzed approximately 10 fb(-1) of proton-antiproton collisions with a center-of-mass energy of 1.96 TeV collected at the Fermilab Tevatron. Two models predicting exotic Higgs bosons with J(P) = 0(-) and J(P) = 2(+) are tested. The kinematic properties of exotic Higgs boson production in association with a vector boson differ from those predicted for the standard model Higgs boson. Upper limits at the 95% credibility level on the production rates of the exotic Higgs bosons, expressed as fractions of the standard model Higgs boson production rate, are set at 0.36 for both the J(P) = 0(-) hypothesis and the J(P) = 2(+) hypothesis. If the production rate times the branching ratio to a bottom-antibottom pair is the same as that predicted for the standard model Higgs boson, then the exotic bosons are excluded with significances of 5.0 standard deviations and 4.9 standard deviations for the J(P) = 0(-) and J(P) = 2(+) hypotheses, respectively.
|
|
| 12. |
- Abel, I, et al.
(författare)
-
Overview of the JET results with the ITER-like wall
- 2013
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 53:10, s. 104002-
-
Tidskriftsartikel (refereegranskat)abstract
- Following the completion in May 2011 of the shutdown for the installation of the beryllium wall and the tungsten divertor, the first set of JET campaigns have addressed the investigation of the retention properties and the development of operational scenarios with the new plasma-facing materials. The large reduction in the carbon content (more than a factor ten) led to a much lower Z(eff) (1.2-1.4) during L- and H-mode plasmas, and radiation during the burn-through phase of the plasma initiation with the consequence that breakdown failures are almost absent. Gas balance experiments have shown that the fuel retention rate with the new wall is substantially reduced with respect to the C wall. The re-establishment of the baseline H-mode and hybrid scenarios compatible with the new wall has required an optimization of the control of metallic impurity sources and heat loads. Stable type-I ELMy H-mode regimes with H-98,H-y2 close to 1 and beta(N) similar to 1.6 have been achieved using gas injection. ELM frequency is a key factor for the control of the metallic impurity accumulation. Pedestal temperatures tend to be lower with the new wall, leading to reduced confinement, but nitrogen seeding restores high pedestal temperatures and confinement. Compared with the carbon wall, major disruptions with the new wall show a lower radiated power and a slower current quench. The higher heat loads on Be wall plasma-facing components due to lower radiation made the routine use of massive gas injection for disruption mitigation essential.
|
|
| 13. |
|
|
| 14. |
|
|
| 15. |
- Agostoni, C, et al.
(författare)
-
Enteral nutrient supply for preterm infants : commentary from the European society of paediatric gastroenterology, hepatology and nutrition committee on nutrition
- 2010
-
Ingår i: Journal of Pediatric Gastroenterology and Nutrition - JPGN. - New York : Raven P.. - 0277-2116 .- 1536-4801. ; 50:1, s. 85-91
-
Tidskriftsartikel (refereegranskat)abstract
- The number of surviving children born prematurely has increased substantially during the last 2 decades. The major goal of enteral nutrient supply to these infants is to achieve growth similar to foetal growth coupled with satisfactory functional development. The accumulation of knowledge since the previous guideline on nutrition of preterm infants from the Committee on Nutrition of the European Society of Paediatric Gastroenterology and Nutrition in 1987 has made a new guideline necessary. Thus, an ad hoc expert panel was convened by the Committee on Nutrition of the European Society of Paediatric Gastroenterology, Hepatology, and Nutrition in 2007 to make appropriate recommendations. The present guideline, of which the major recommendations are summarised here (for the full report, see http://links.lww.com/A1480), is consistent with, but not identical to, recent guidelines from the Life Sciences Research Office of the American Society for Nutritional Sciences published in 2002 and recommendations from the handbook Nutrition of the Preterm Infant. Scientific Basis and Practical Guidelines, 2nd ed, edited by Tsang et al, and published in 2005. The preferred food for premature infants is fortified human milk from the infant's own mother, or, alternatively, formula designed for premature infants. This guideline aims to provide proposed advisable ranges for nutrient intakes for stable-growing preterm infants up to a weight of approximately 1800 g, because most data are available for these infants. These recommendations are based on a considered review of available scientific reports on the subject, and on expert consensus for which the available scientific data are considered inadequate.
|
|
| 16. |
|
|
| 17. |
|
|
| 18. |
|
|
| 19. |
|
|
| 20. |
|
|
| 21. |
- Arnalds, Unnar B., et al.
(författare)
-
A new look on the two-dimensional Ising model : thermal artificial spins
- 2016
-
Ingår i: New Journal of Physics. - : IOP Publishing. - 1367-2630. ; 18
-
Tidskriftsartikel (refereegranskat)abstract
- We present a direct experimental investigation of the thermal ordering in an artificial analogue of an asymmetric two-dimensional Ising system composed of a rectangular array of nano-fabricated magnetostatically interacting islands. During fabrication and below a critical thickness of the magnetic material the islands are thermally fluctuating and thus the system is able to explore its phase space. Above the critical thickness the islands freeze-in resulting in an arrested thermalized state for the array. Determining the magnetic state we demonstrate a genuine artificial two-dimensional Ising system which can be analyzed in the context of nearest neighbor interactions.
|
|
| 22. |
- Asimakopoulou, Eleni Myrto, et al.
(författare)
-
Development towards high-resolution kHz-speed rotation-free volumetric imaging
- 2024
-
Ingår i: Optics Express. - 1094-4087. ; 32:3, s. 4413-4426
-
Tidskriftsartikel (refereegranskat)abstract
- X-ray multi-projection imaging (XMPI) has the potential to provide rotation-free 3D movies of optically opaque samples. The absence of rotation enables superior imaging speed and preserves fragile sample dynamics by avoiding the centrifugal forces introduced by conventional rotary tomography. Here, we present our XMPI observations at the ID19 beamline (ESRF, France) of 3D dynamics in melted aluminum with 1000 frames per second and 8 µm resolution per projection using the full dynamical range of our detectors. Since XMPI is a method under development, we also provide different tests for the instrumentation of up to 3000 frames per second. As the high-brilliance of 4th generation light-sources becomes more available, XMPI is a promising technique for current and future X-ray imaging instruments.
|
|
| 23. |
- Baskurt, Oguz, et al.
(författare)
-
New guidelines for hemorheological laboratory techniques
- 2009
-
Ingår i: Clinical hemorheology and microcirculation. - 1386-0291 .- 1875-8622. ; 42:2, s. 75-97
-
Tidskriftsartikel (refereegranskat)abstract
- This document, supported by both the International Society for Clinical Hemorheology and the European Society for Clinical Hemorheology and Microcirculation, proposes new guidelines for hemorheological methods used in experimental and clinical studies. It is based on a similar document entitled: "Guidelines for measurement of blood viscosity and erythrocyte deformability" published in 1986 by the Expert Panel on Blood Rheology of the International Committee for Standardization in Hematology. Recent methods techniques and instruments, as well as new approaches to interpretation of results, are added to these new guidelines; wide spread adoption should improve comparability between hemorheological laboratories and increase the reliability of rheological tests.
|
|
| 24. |
- Bert, Valérie, et al.
(författare)
-
How to manage plant biomass originated from phytotechnologies? : Gathering perceptions from end-users
- 2017
-
Ingår i: International journal of phytoremediation. - : Taylor & Francis. - 1522-6514 .- 1549-7879. ; 19:10, s. 947-954
-
Tidskriftsartikel (refereegranskat)abstract
- A questionnaire survey was carried out in 4 European countries to gather end-user's perceptions of using plants from phytotechnologies in combustion and anaerobic digestion (AD). 9 actors of the wood energy sector from France, Germany and Sweden, and 11 AD platform operators from France, Germany and Austria were interviewed. Questions related to installation, input materials, performed analyses, phytostabilization and phytoextraction. Although the majority of respondents did not know phytotechnologies, results suggested that plant biomass from phytomanaged areas could be used in AD and combustion, under certain conditions. As a potential advantage, these plants would not compete with plants grown on agricultural lands, contaminated lands being not suitable for agriculture production. Main limitations would be related to additional controls in process' inputs and end-products and installations that might generate additional costs. In most cases, price of phytotechnologies biomass was mentioned as a driver to potentially use plants from metal-contaminated soils. Plants used in phytostabilisation or phytoexclusion were thought to be less risky and, consequently, benefited from a better theoretical acceptance than those issued from phytoextraction. Results were discussed according to national regulations. One issue related to the regulatory gap concerning the status of the plant biomass produced on contaminated land.
|
|
| 25. |
- Beurskens, M, et al.
(författare)
-
L-H power Threshold, Pedestal Stability and Confinement in JET with a Metallic Wall
- 2012
-
Ingår i: 24th IAEA Fusion Energy Conference, 8-13 October 2012. ; , s. EX/P4-23-
-
Konferensbidrag (refereegranskat)abstract
- After the change-over from the Carbon-Fibre Composite (CFC) wall to an ITER-like metallic wall (ILW) the baseline type I ELMy H-mode scenario has been re-established in JET with the new plasma-facing materials Be and W. A key finding for ITER is that the power required to enter H-mode has reduced with respect to that in JET with the CFC wall. In JET with the ILW the power threshold to enter H-mode (PL-H) is below the international L-H power threshold scaling P_Martin-08. The minimum threshold is P_L-H=1.8MW compared to P_Martin-08=4MW with a pedestal density of nped=2x10^19m^-3 in plasmas with I_p=2.0 MA, B_t=2.4T. However the threshold depends strongly on density; using slow ion cyclotron heating (ICRH) power ramps P_L-H varies from 1.8 to 4.5MW in a range of lower and upper plasma triangularity (delta_L=0.32-0.4, delta_U =0.19-0.38). Stationary Type I ELMy H-mode operation has been re-established at both low and high triangularity with I_p≤ 2.5MA, q_95=2.8-3.6 and H_98≤1. The achieved plasma collisionality is relatively high, in the range of 1< nu_eff<4 due to the required strong gas dosing. Stability analysis with the linear MHD stability code ELITE show that the pedestal is marginally unstable with respect to the Peeling Ballooning boundary. Due to the stabilising effect of the global pressure Beta_N on the pedestal stability, a strong coupling between core and edge confinement is expected. Indeed in an H-mode profile database comparison with 119 CFC- (0.1< nu_eff<1) and 40 ILW-H-modes a strong coupling of the core versus edge confinement is found, independent of wall material. In addition, the pedestal predictions using the EPED predictive pedestal code coincide with the measured pedestal height over a wide range of normalised pressure 1.5< Beta_N<3.5. Due to the strong core-edge coupling, beneficial effects of core profile peaking on confinement are weak in the database comparison. However, differences in the individual temperature and density profile peaking occur across the database. When collisionality is increased from nu_eff=0.1 to 4, the density peaking decreases from R/L_ne=4 to 0.5 but is compensated by an increase in temperature peaking from R/L_Te = 5-8, offering a challenge for micro turbulence-transport models.
|
|
| 26. |
- Beurskens, M. N. A., et al.
(författare)
-
Global and pedestal confinement in JET with a Be/W metallic wall
- 2014
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 0029-5515 .- 1741-4326. ; 54:4, s. 043001-
-
Tidskriftsartikel (refereegranskat)abstract
- Type I ELMy H-mode operation in JET with the ITER-like Be/W wall (JET-ILW) generally occurs at lower pedestal pressures compared to those with the full carbon wall (JET-C). The pedestal density is similar but the pedestal temperature where type I ELMs occur is reduced and below to the so-called critical type I-type III transition temperature reported in JET-C experiments. Furthermore, the confinement factor H-98(y,H- 2) in type I ELMy H-mode baseline plasmas is generally lower in JET-ILWcompared to JET-C at low power fractions Ploss/P-thr,(08)< 2 (where P-loss is (P-in-dW/dt), and P-thr,(08) the L-H power threshold from Martin et al 2008 (J. Phys. Conf. Ser. 123 012033)). Higher power fractions have thus far not been achieved in the baseline plasmas. At Ploss/P-thr,P- 08 > 2, the confinement in JET-ILW hybrid plasmas is similar to that in JET-C. A reduction in pedestal pressure is the main reason for the reduced confinement in JET-ILW baseline ELMy H-mode plasmas where typically H-98((y, 2)) = 0.8 is obtained, compared to H-98((y, 2)) = 1.0 in JET-C. In JET-ILW hybrid plasmas a similarly reduced pedestal pressure is compensated by an increased peaking of the core pressure profile resulting in H-98((y, 2)) <= 1.25. The pedestal stability has significantly changed in high triangularity baseline plasmas where the confinement loss is also most apparent. Applying the same stability analysis for JET-C and JET-ILW, the measured pedestal in JET-ILW is stable with respect to the calculated peeling-ballooning stability limit and the ELM collapse time has increased to 2ms from typically 200 mu s in JET-C. This indicates that changes in the pedestal stability may have contributed to the reduced pedestal confinement in JET-ILW plasmas. A comparison of EPED1 pedestal pressure prediction with JET-ILW experimental data in over 500 JET-C and JET-ILW baseline and hybrid plasmas shows a good agreement with 0.8 < (measured p(ped))/(predicted p(ped), EPED) < 1.2, but that the role of triangularity is generally weaker in the JET-ILW experimental data than in the model predictions.
|
|
| 27. |
|
|
| 28. |
- Beurskens, M. N. A., et al.
(författare)
-
The effect of a metal wall on confinement in JET and ASDEX Upgrade
- 2013
-
Ingår i: Plasma Physics and Controlled Fusion. - : IOP Publishing. - 0741-3335 .- 1361-6587. ; 55:12, s. 124043-
-
Tidskriftsartikel (refereegranskat)abstract
- In both JET and ASDEX Upgrade (AUG) the plasma energy confinement has been affected by the presence of a metal wall by the requirement of increased gas fuelling to avoid tungsten pollution of the plasma. In JET with a beryllium/tungsten wall the high triangularity baseline H-mode scenario (i.e. similar to the ITER reference scenario) has been the strongest affected and the benefit of high shaping to give good normalized confinement of H-98 similar to 1 at high Greenwald density fraction of f(GW) similar to 0.8 has not been recovered to date. In AUG with a full tungsten wall, a good normalized confinement H-98 similar to 1 could be achieved in the high triangularity baseline plasmas, albeit at elevated normalized pressure beta(N) > 2. The confinement lost with respect to the carbon devices can be largely recovered by the seeding of nitrogen in both JET and AUG. This suggests that the absence of carbon in JET and AUG with a metal wall may have affected the achievable confinement. Three mechanisms have been tested that could explain the effect of carbon or nitrogen (and the absence thereof) on the plasma confinement. First it has been seen in experiments and by means of nonlinear gyrokinetic simulations (with the GENE code), that nitrogen seeding does not significantly change the core temperature profile peaking and does not affect the critical ion temperature gradient. Secondly, the dilution of the edge ion density by the injection of nitrogen is not sufficient to explain the plasma temperature and pressure rise. For this latter mechanism to explain the confinement improvement with nitrogen seeding, strongly hollow Z(eff) profiles would be required which is not supported by experimental observations. The confinement improvement with nitrogen seeding cannot be explained with these two mechanisms. Thirdly, detailed pedestal structure analysis in JET high triangularity baseline plasmas have shown that the fuelling of either deuterium or nitrogen widens the pressure pedestal. However, in JET-ILW this only leads to a confinement benefit in the case of nitrogen seeding where, as the pedestal widens, the obtained pedestal pressure gradient is conserved. In the case of deuterium fuelling in JET-ILW the pressure gradient is strongly degraded in the fuelling scan leading to no net confinement gain due to the pedestal widening. The pedestal code EPED correctly predicts the pedestal pressure of the unseeded plasmas in JET-ILW within +/- 5%, however it does not capture the complex variation of pedestal width and gradient with fuelling and impurity seeding. Also it does not predict the observed increase of pedestal pressure by nitrogen seeding in JET-ILW. Ideal peeling ballooning MHD stability analysis shows that the widening of the pedestal leads to a down shift of the marginal stability boundary by only 10-20%. However, the variations in the pressure gradient observed in the JET-ILW fuelling experiment is much larger and spans a factor of more than two. As a result the experimental points move from deeply unstable to deeply stable on the stability diagram in a deuterium fuelling scan. In AUG-W nitrogen seeded plasmas, a widening of the pedestal has also been observed, consistent with the JET observations. The absence of carbon can thus affect the pedestal structure, and mainly the achieved pedestal gradient, which can be recovered by seeding nitrogen. The underlying physics mechanism is still under investigation and requires further understanding of the role of impurities on the pedestal stability and pedestal structure formation.
|
|
| 29. |
|
|
| 30. |
- Bilger, R, et al.
(författare)
-
Spectator tagging in quasi-free pn-reactions on deuterium at PROMICE/WASA, CELSIUS
- 2000
-
Ingår i: Nuclear Physics A. - : Elsevier Science B.V. Holland. ; , s. 1053c-1056c
-
Konferensbidrag (refereegranskat)abstract
- A set of silicon detectors has been added to the PROMICE/WASA (P/W) experiment at CELSIUS. These detectors have been used for spectator-proton tagging in proton deuteron collisions to investigate proton-neutron reactions at intermediate energies. The perf
|
|
| 31. |
|
|
| 32. |
|
|
| 33. |
|
|
| 34. |
- Busse, Christian, 1989-
(författare)
-
Modelling of Crack Growth in Single-Crystal Nickel-Base Superalloys
- 2019
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- This dissertation was produced at the Division of Solid Mechanics at Linköping University and is part of a research project, which comprises modelling, microstructure investigations and material testing of cast nickel-base superalloys. The main objective of this work was to deepen the understanding of the fracture behaviour of single-crystal nickel-base superalloys and to develop a model to predict the fatigue crack growth behaviour. Frequently, crack growth in these materials has been observed to follow one of two distinct cracking modes; Mode I like cracking perpendicular to the loading direction or crystallographic crack growth on the octahedral {111}-planes, where the latter is associated with an increased fatigue crack growth rate. Thus, it is of major importance to account for this behaviour in component life prediction. Consequently, a model for the prediction of the transition of cracking modes and the correct active crystallographic plane, i.e. the crack path, and the crystallographic crack growth rate has been developed. This model is based on the evaluation of appropriate crack driving forces using three-dimensional finite-element simulations. A special focus was given towards the influence of the crystallographic orientation on the fracture behaviour. Further, a model to incorporate residual stresses in the crack growth modelling is presented. All modelling work is calibrated and validated by experiments on different specimen geometries with different crystallographic orientations. This dissertation consists of two parts, where Part I gives an introduction and background to the field of research, while Part II consists of six appended papers.
|
|
| 35. |
- Callahan, Emily A., et al.
(författare)
-
Assessing the safety of bioactive ingredients in infant formula that affect the immune system : recommendations from an expert panel
- 2022
-
Ingår i: American Journal of Clinical Nutrition. - : Oxford University Press. - 0002-9165 .- 1938-3207. ; 115:2, s. 570-587
-
Tidskriftsartikel (refereegranskat)abstract
- Bioactive ingredients for infant formula have been sought to reduce disparities in health outcomes between breastfed and formula-fed infants. Traditional food safety methodologies have limited ability to assess some bioactive ingredients. It is difficult to assess the effects of nutrition on the infant immune system because of coincident developmental adaptations to birth, establishment of the microbiome and introduction to solid foods, and perinatal environmental factors. An expert panel was convened to review information on immune system development published since the 2004 Institute of Medicine report on evaluating the safety of new infant formula ingredients and to recommend measurements that demonstrate the safety of bioactive ingredients intended for that use. Panel members participated in a 2-d virtual symposium in November 2020 and in follow-up discussions throughout early 2021. Key topics included identification of immune system endpoints from nutritional intervention studies, effects of human milk feeding and human milk substances on infant health outcomes, ontologic development of the infant immune system, and microbial influences on tolerance. The panel explored how "nonnormal" conditions such as preterm birth, allergy, and genetic disorders could help define developmental immune markers for healthy term infants. With consideration of breastfed infants as a reference, ensuring proper control groups, and attention to numerous potential confounders, the panel recommended a set of standard clinical endpoints including growth, response to vaccination, infection and other adverse effects related to inflammation, and allergy and atopic diseases. It compiled a set of candidate markers to characterize stereotypical patterns of immune system development during infancy, but absence of reference ranges, variability in methods and populations, and unreliability of individual markers to predict disease prevented the panel from including many markers as safety endpoints. The panel's findings and recommendations are applicable for industry, regulatory, and academic settings, and will inform safety assessments for immunomodulatory ingredients in foods besides infant formula.
|
|
| 36. |
- Coenen, J. W., et al.
(författare)
-
Long-term evolution of the impurity composition and impurity events with the ITER-like wall at JET
- 2013
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 0029-5515 .- 1741-4326. ; 53:7, s. 073043-
-
Tidskriftsartikel (refereegranskat)abstract
- This paper covers aspects of long-term evolution of intrinsic impurities in the JET tokamak with respect to the newly installed ITER-like wall (ILW). At first the changes related to the change over from the JET-C to the JET-ILW with beryllium (Be) as the main wall material and tungsten (W) in the divertor are discussed. The evolution of impurity fluxes in the newly installed W divertor with respect to studying material migration is described. In addition, a statistical analysis of transient impurity events causing significant plasma contamination and radiation losses is shown. The main findings comprise a drop in carbon content (x20) (see also Brezinsek et al (2013 J. Nucl. Mater. 438 S303)), low oxygen content (x10) due to the Be first wall (Douai et al 2013 J. Nucl. Mater. 438 S1172-6) as well as the evolution of the material mix in the divertor. Initially, a short period of repetitive ohmic plasmas was carried out to study material migration (Krieger et al 2013 J. Nucl. Mater. 438 S262). After the initial 1600 plasma seconds the material surface composition is, however, still evolving. With operational time, the levels of recycled C are increasing slightly by 20% while the Be levels in the deposition-dominated inner divertor are dropping, hinting at changes in the surface layer material mix made of Be, C and W. A steady number of transient impurity events, consisting of W and constituents of inconel, is observed despite the increase in variation in machine operation and changes in magnetic configuration as well as the auxiliary power increase.
|
|
| 37. |
- Coenen, J. W., et al.
(författare)
-
Tungsten erosion in the all-metal tokamaks JET and ASDEX Upgrade
- 2012
-
Ingår i: 39th EPS Conference on Plasma Physics 2012, EPS 2012 and the 16th International Congress on Plasma Physics. - 9781622769810 ; , s. 253-256
-
Konferensbidrag (refereegranskat)abstract
- The tungsten source in the all W outer divertor and Be main wall configuration has been quantified mainly during L-mode plasmas and compared to AUG Data both gained from local spectroscopy. Results so far show differences between AUG and JET based on impurities in the plasma changing the sputter behavior. This stresses the need for detailed analysis of the divertor impurity composition and detailed molding in the future analysis. The H-Mode examples indicate at ELM dominated sputtering and a rather low averaged sputtering yield in general. Nitrogen seeding can change the divertor conditions significantly either increasing W sputtering or suppressing it due to local cooling, JET and AUG behave similarly. All together it is clear that by having low divertor temperature or a beneficial impurity composition sputtering can be controlled and is rather low as expected in an all metal environment.
|
|
| 38. |
- de Beaufort, Carine E., et al.
(författare)
-
Metabolic outcomes in young children with type 1 diabetes differ between treatment centers : the Hvidoere Study in Young Children 2009
- 2013
-
Ingår i: Pediatric Diabetes. - : Hindawi Limited. - 1399-543X .- 1399-5448. ; 14:6, s. 422-428
-
Tidskriftsartikel (refereegranskat)abstract
- Objective: To investigate whether center differences in glycemic control are present in prepubertal children <11yr with type 1 diabetes mellitus. Research Design and Methods: This cross-sectional study involved 18 pediatric centers worldwide. All children, <11 y with a diabetes duration 12months were invited to participate. Case Record Forms included information on clinical characteristics, insulin regimens, diabetic ketoacidosis (DKA), severe hypoglycemia, language difficulties, and comorbidities. Hemoglobin A1c (HbA1c) was measured centrally by liquid chromatography (DCCT aligned, range: 4.4-6.3%; IFFC: 25-45mmol/mol). Results: A total of 1133 children participated (mean age: 8.0 +/- 2.1 y; females: 47.5%, mean diabetes duration: 3.8 +/- 2.1 y). HbA1c (overall mean: 8.0 +/- 1.0%; range: 7.3-8.9%) and severe hypoglycemia frequency (mean 21.7 events per 100 patient-years), but not DKA, differed significantly between centers (p<0.001 resp. p=0.179). Language difficulties showed a negative relationship with HbA1c (8.3 +/- 1.2% vs. 8.0 +/- 1.0%; p = 0.036). Frequency of blood glucose monitoring demonstrated a significant but weak association with HbA1c (r=-0.17; p<0.0001). Although significant different HbA1c levels were obtained with diverse insulin regimens (range: 7.3-8.5%; p<0.001), center differences remained after adjusting for insulin regimen (p<0.001). Differences between insulin regimens were no longer significant after adjusting for center effect (p=0.199). Conclusions: Center differences in metabolic outcomes are present in children <11yr, irrespective of diabetes duration, age, or gender. The incidence of severe hypoglycemia is lower than in adolescents despite achieving better glycemic control. Insulin regimens show a significant relationship with HbA1c but do not explain center differences. Each center's effectiveness in using specific treatment strategies remains the key factor for outcome.
|
|
| 39. |
|
|
| 40. |
|
|
| 41. |
|
|
| 42. |
|
|
| 43. |
- Fellinger, Joris, et al.
(författare)
-
Tungsten based divertor development for Wendelstein 7-X
- 2023
-
Ingår i: Nuclear Materials and Energy. - 2352-1791. ; 37
-
Tidskriftsartikel (refereegranskat)abstract
- Wendelstein 7-X, the world’s largest superconducting stellarator in Greifswald (Germany), started plasma experiments with a water-cooled plasma-facing wall in 2022, allowing for long pulse operation. In parallel, a project was launched in 2021 to develop a W based divertor, replacing the current CFC divertor, to demonstrate plasma performance of a stellarator with a reactor relevant plasma facing materials with low tritium retention. The project consists of two tasks: Based on experience from the previous experimental campaigns and improved physics modelling, the geometry of the plasma-facing surface of the divertor and baffles is optimized to prevent overloads and to improve exhaust. In parallel, the manufacturing technology for a W based target module is qualified. This paper gives a status update of project. It focusses on the conceptual design of a W based target module, the manufacturing technology and its qualification, which is conducted in the framework of the EUROfusion funded WPDIV program. A flat tile design in which a target module is made of a single target element is pursued. The technology must allow for moderate curvatures of the plasma-facing surface to follow the magnetic field lines. The target element is designed for steady state heat loads of 10 MW/m2 (as for the CFC divertor). Target modules of a similar size and weight as for the CFC divertor are assumed (approx. < 0.25 m2 and < 60 kg) using the existing water cooling infrastructure providing 5 l/s and roughly maximum 15 bar pressure drop per module. The main technology under qualification is based on a CuCrZr heat sink made either by additive manufacturing using laser powder bed fusion (LPBF) or by uniaxial diffusion welding of pre-machined forged CuCrZr plates. After heat treatment, the plasma-facing side of the heat sink is covered by W or if feasible by the more ductile WNiFe, preferably by coating or alternatively by hot isostatic pressing W based tiles with a soft OFE-Cu interlayer. Last step is a final machining of the plasma-exposed surface and the interfaces to the water supply lines and supports to correct manufacturing deformations.
|
|
| 44. |
- Fleming, Stephen A., et al.
(författare)
-
An expert panel on the adequacy of safety data and physiological roles of dietary bovine osteopontin in infancy
- 2024
-
Ingår i: Frontiers in Nutrition. - : Frontiers Media S.A.. - 2296-861X. ; 11
-
Forskningsöversikt (refereegranskat)abstract
- Human milk, due to its unique composition, is the optimal standard for infant nutrition. Osteopontin (OPN) is abundant in human milk but not bovine milk. The addition of bovine milk osteopontin (bmOPN) to formula may replicate OPN’s concentration and function in human milk. To address safety concerns, we convened an expert panel to assess the adequacy of safety data and physiological roles of dietary bmOPN in infancy. The exposure of breastfed infants to human milk OPN (hmOPN) has been well-characterized and decreases markedly over the first 6 months of lactation. Dietary bmOPN is resistant to gastric and intestinal digestion, absorbed and cleared from circulation within 8–24 h, and represents a small portion (<5%) of total plasma OPN. Label studies on hmOPN suggest that after 3 h, intact or digested OPN is absorbed into carcass (62%), small intestine (23%), stomach (5%), and small intestinal perfusate (4%), with <2% each found in the cecum, liver, brain, heart, and spleen. Although the results are heterogenous with respect to bmOPN’s physiologic impact, no adverse impacts have been reported across growth, gastrointestinal, immune, or brain-related outcomes. Recombinant bovine and human forms demonstrate similar absorption in plasma as bmOPN, as well as effects on cognition and immunity. The panel recommended prioritization of trials measuring a comprehensive set of clinically relevant outcomes on immunity and cognition to confirm the safety of bmOPN over that of further research on its absorption, distribution, metabolism, and excretion. This review offers expert consensus on the adequacy of data available to assess the safety of bmOPN for use in infant formula, aiding evidence-based decisions on the formulation of infant formula.
|
|
| 45. |
|
|
| 46. |
- Frassinetti, Lorenzo, et al.
(författare)
-
Effect of nitrogen seeding on the energy losses and on the time scales of the electron temperature and density collapse of type-I ELMs in JET with the ITER-like wall
- 2015
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 0029-5515 .- 1741-4326. ; 55:2
-
Tidskriftsartikel (refereegranskat)abstract
- The baseline type-I ELMy H-mode scenario has been re-established in JET with the new tungsten MKII-HD divertor and beryllium on the main wall (hereafter called the ITER-like wall, JET-ILW). The first JET-ILW results show that the confinement is degraded by 20-30% in the baseline scenarios compared to the previous carbon wall JET (JET-C) plasmas. The degradation is mainly driven by the reduction in the pedestal temperature. Stored energies and pedestal temperature comparable to the JET-C have been obtained to date in JET-ILW baseline plasmas only in the high triangularity shape using N-2 seeding. This work compares the energy losses during ELMs and the corresponding time scales of the temperature and density collapse in JET-ILWbaseline plasmas with and without N-2 seeding with similar JET-C baseline plasmas. ELMs in the JET-ILW differ from those with the carbon wall both in terms of time scales and energy losses. The ELM time scale, defined as the time to reach the minimum pedestal temperature soon after the ELM collapse, is similar to 2ms in the JET-ILW and lower than 1 ms in the JET-C. The energy losses are in the range Delta W-ELM/W-ped approximate to 7-12% in the JET-ILWand Delta W-ELM/W-ped approximate to 10-20% in JET-C, and fit relatively well with earlier multi-machine empirical scalings of Delta W-ELM/W-ped with collisionality. The time scale of the ELM collapse seems to be related to the pedestal collisionality. Most of the non-seeded JET-ILW ELMs are followed by a further energy drop characterized by a slower time scale similar to 8-10 ms (hereafter called slow transport events), that can lead to losses in the range Delta W-slow/W-ped approximate to 15-22%, slightly larger than the losses in JET-C. The N-2 seeding in JET-ILW significantly affects the ELMs. The JET-ILW plasmas with N-2 seeding are characterized by ELM energy losses and time scales similar to the JET-C and by the absence of the slow transport events.
|
|
| 47. |
|
|
| 48. |
|
|
| 49. |
|
|
| 50. |
- García-Moreno, Francisco, et al.
(författare)
-
Using X-ray tomoscopy to explore the dynamics of foaming metal
- 2019
-
Ingår i: Nature Communications. - : Springer Science and Business Media LLC. - 2041-1723. ; 10:1
-
Tidskriftsartikel (refereegranskat)abstract
- The complex flow of liquid metal in evolving metallic foams is still poorly understood due to difficulties in studying hot and opaque systems. We apply X-ray tomoscopy –the continuous acquisition of tomographic (3D) images– to clarify key dynamic phenomena in liquid aluminium foam such as nucleation and growth, bubble rearrangements, liquid retraction, coalescence and the rupture of films. Each phenomenon takes place on a typical timescale which we cover by obtaining 208 full tomograms per second over a period of up to one minute. An additional data processing algorithm provides information on the 1 ms scale. Here we show that bubble coalescence is not only caused by gravity-induced drainage, as experiments under weightlessness show, and by stresses caused by foam growth, but also by local pressure peaks caused by the blowing agent. Moreover, details of foam expansion and phenomena such as rupture cascades and film thinning before rupture are quantified. These findings allow us to propose a way to obtain foams with smaller and more equally sized bubbles.
|
|
