| 1. |
- Chu, Ming, et al.
(författare)
-
Accurate capacitance-voltage characterization of organic thin films with current injection*
- 2021
-
Ingår i: Chinese Physics B. - : IOP PUBLISHING LTD. - 1674-1056. ; 30:8
-
Tidskriftsartikel (refereegranskat)abstract
- To deal with the invalidation of commonly employed series model and parallel model in capacitance-voltage (C-V) characterization of organic thin films when current injection is significant, a three-element equivalent circuit model is proposed. On this basis, the expression of real capacitance in consideration of current injection is theoretically derived by small-signal analysis method. The validity of the proposed equivalent circuit and theoretical expression are verified by a simulating circuit consisting of a capacitor, a diode, and a resistor. Moreover, the accurate C-V characteristic of an organic thin film device is obtained via theoretical correction of the experimental measuring result, and the real capacitance is 35.7% higher than the directly measured capacitance at 5-V bias in the parallel mode. This work strongly demonstrates the necessity to consider current injection in C-V measurement and provides a strategy for accurate C-V characterization experimentally.
|
|
| 2. |
- Beal, Jacob, et al.
(författare)
-
Robust estimation of bacterial cell count from optical density
- 2020
-
Ingår i: Communications Biology. - : Springer Science and Business Media LLC. - 2399-3642. ; 3:1
-
Tidskriftsartikel (refereegranskat)abstract
- Optical density (OD) is widely used to estimate the density of cells in liquid culture, but cannot be compared between instruments without a standardized calibration protocol and is challenging to relate to actual cell count. We address this with an interlaboratory study comparing three simple, low-cost, and highly accessible OD calibration protocols across 244 laboratories, applied to eight strains of constitutive GFP-expressing E. coli. Based on our results, we recommend calibrating OD to estimated cell count using serial dilution of silica microspheres, which produces highly precise calibration (95.5% of residuals <1.2-fold), is easily assessed for quality control, also assesses instrument effective linear range, and can be combined with fluorescence calibration to obtain units of Molecules of Equivalent Fluorescein (MEFL) per cell, allowing direct comparison and data fusion with flow cytometry measurements: in our study, fluorescence per cell measurements showed only a 1.07-fold mean difference between plate reader and flow cytometry data.
|
|
| 3. |
- Cai, Weidong, 1991-, et al.
(författare)
-
Chirality Induced Crystal Structural Difference in Metal Halide Composites
- 2022
-
Ingår i: Advanced Optical Materials. - : Wiley-V C H Verlag GMBH. - 2162-7568 .- 2195-1071. ; 10:16
-
Tidskriftsartikel (refereegranskat)abstract
- Incorporating chiral organic compounds into metal halide frames is a common and useful method to introduce chirality in metal halide composites. The structures of resulting racemic and chiral composites are usually considered to be nearly identical owing to similar chemical bonding. In this work, by incorporating chiral MBABr (bromide methylbenzylamine) into an inorganic frame, a significant crystallization difference between the resulting racemic and chiral metal halide composites is observed, as confirmed by both structural and spectroscopic measurements. In addition, the structural transformation in the chiral composites can also be induced by moisture, ascribed to the asymmetric hydrogen bonding in chiral materials. These results provide new insights for the future synthesis of chiral materials and open up new possibilities to advance the materials functionalities.
|
|
| 4. |
- Cai, Weidong, et al.
(författare)
-
Multicolor light emission and multifunctional applications in double perovskite-Cs 2 NaInCl 6 by Cu + /Sb 3+co-doping
- 2024
-
Ingår i: Chemical Engineering Journal. - : ELSEVIER SCIENCE SA. - 1385-8947 .- 1873-3212. ; 489
-
Tidskriftsartikel (refereegranskat)abstract
- Halide double perovskites managed by metal doping approach can exhibit dual emission colors, which have been considered as promising multicolor luminescent materials. However, an independent and stable emission at yellow region is missing owing to limited doping candidates, hindering the further commercialization of multicolor luminescence applications in double perovskites. In this work, we successfully obtain stable multicolor emission with PLQE (photoluminescence quantum yield) as high as 78% through developing the CuI doping strategy in Sb-Cs2NaInCl6. By introducing a high CuI feed ratio in airtight autoclave to compete the oxidization effect, the oxidization of CuI into CuII (detrimental factor for high PLQE due to serious quenching effect) is largely suppressed. With changing the CuI feed ratio, at least four distinct emission colors ranging from blue, purple, pink to yellow can be realized via changing the excitation wavelength. Depending on tunable multicolor emission, we further demonstrate the promise of our co-doped double perovskites in anti-counterfeiting technology and multicolor lighting devices. Our results open the way for enriching the optical applications of double perovskites based on multicolor emission.
|
|
| 5. |
- Cai, Weidong, et al.
(författare)
-
Multicolor light emission in manganese-based metal halide composites
- 2022
-
Ingår i: Applied Physics Reviews. - : AIP Publishing. - 1931-9401. ; 9:4
-
Tidskriftsartikel (refereegranskat)abstract
- Manganese-based organic-inorganic metal halide composites have been considered as promising candidates for lead-free emitters. However, in spite of their excellent luminescence properties in green and red regions, blue emission-a critical component for white light generation-from pristine manganese-based composites is currently missing. In this work, we successfully achieve blue luminescence center in manganese-based composites through selecting specific organic component methylbenzylamine (MBA). Our approach is fundamentally different from green and red emission in manganese-based composites, which result from manganese-halide frameworks. The coexistence of different luminescence centers in our manganese-based composites is confirmed by photoluminescence (PL) and photoluminescence excitation (PLE) results. As a result of different photoluminescence excitation responses of different emission centers, the resulting emission color can be tuned with selecting different excitation wavelengths. Specifically, a white light emission can be obtained with Commission Internationale de leclairage coordinates of (0.33, 0.35) upon the 330 nm excitation. We further demonstrate the promise of our manganese-based composites in the anti-counterfeiting technology and multicolor lighting. Our results provide a novel strategy for full-spectral emission in manganese-based organic-inorganic metal halide composites and lay a solid foundation for a range of new applications. (C) 2022 Author(s).
|
|
| 6. |
- Cai, Weidong, 1991-
(författare)
-
Tunning Multicolor Light Emission in Lead-free Materials
- 2023
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Perovskites are a class of compounds with the general formula ABX3 and becoming increasingly attractive recently. Because this kind of material possesses various advantages such as abundant raw materials, easy synthesis, excellent photoelectric properties, and short production process. As one of the applications for lead-based perovskites, the perovskite solar cells have quickly enhanced their PCE from 3.8% in 2009 to over 25% within a short period. However, the problems, such as instability of the ionic crystal nature and toxicity of lead, largely hinder the lead-based perovskites towards commercialization. Therefore, it is necessary to develop new lead-free materials as alternative to lead-based perovskites, where similar structures can be formed to inherit the excellent optoelectronic properties. Moreover, new properties can be achieved due to more abundant metal candidates in lead-free materials. Based on this, we develop different kinds of perovskite-structure-like lead-free materials such as organic inorganic hybrid materials, chiral materials and double perovskites. In addition to physical and chemical properties like photoluminescence, absorption, structure, etc., we further demonstrate their potential applications according to their unique properties such as multicolor light emission.We incorporate chiral MBA (methylbenzylamine) in inorganic metal system to obtain chiral lead-free organic inorganic hybrid materials, where significant crystallization difference is observed between rac and chiral halide compounds for the first time. Such difference is confirmed by spectrum and structural results. What’s more, we find that moisture can cause the structural transfer in chiral compounds, attributed to the asymmetric hydrogen bonding of chiral compounds. Our achievements open up new chance to improve our material property and provide new horizon for synthesis of chiral materials in the future.Then, we obtained blue emission center in Mn-based organic and inorganic compounds by choosing organic molecule MBA. The method has basic difference with the emissions in Mn based compounds. The coexisting two emission centers of our Mn based samples is verified by spectral results. Because two emission centers can induce different PL excitation responses, so that the excitation wavelengths are capable of manipulating the emission color. Specifically, we achieve CIE coordinates of (0.33, 0.35) with a white emission. The potential of our materials in anti-counterfeiting and multicolor lighting technology are further demonstrated. Our accomplishments explore a new approach for multicolor emission in Mn based materials.We finally obtained Sb3+/Cu+ co-doped Cs2NaInCl6 (CNIC) double perovskite by hydrothermal reaction which exhibits tunable dual emissions with PL quantum efficiency (PLQE) of 78%. Depending on different photoluminescence excitation (PLE) spectra between two emissions, multiple emission colors can be got by manipulating excitation wavelength. Interestingly, emission color gamut can be further tuned through manipulating the feeding ratio of CuI dopant, where warm color and cool color can be achieved separately. We further illustrated the application potential of our co-doped materials in the fileds of multicolor lighting devices and anti-counterfeiting. Our achievements open up a brand-new strategy for wider spectral luminescence of double perovskites and pace up the road for a series of new applications.
|
|
| 7. |
- Cai, Xia, et al.
(författare)
-
Data-driven design of high-performance MASn(x)Pb(1-x)I(3) perovskite materials by machine learning and experimental realization
- 2022
-
Ingår i: Light. - : Springer Nature. - 2095-5545 .- 2047-7538. ; 11:1
-
Tidskriftsartikel (refereegranskat)abstract
- The photovoltaic performance of perovskite solar cell is determined by multiple interrelated factors, such as perovskite compositions, electronic properties of each transport layer and fabrication parameters, which makes it rather challenging for optimization of device performances and discovery of underlying mechanisms. Here, we propose and realize a novel machine learning approach based on forward-reverse framework to establish the relationship between key parameters and photovoltaic performance in high-profile MASn(x)Pb(1-x)I(3) perovskite materials. The proposed method establishes the asymmetrically bowing relationship between band gap and Sn composition, which is precisely verified by our experiments. Based on the analysis of structural evolution and SHAP library, the rapid-change region and low-bandgap plateau region for small and large Sn composition are explained, respectively. By establishing the models for photovoltaic parameters of working photovoltaic devices, the deviation of short-circuit current and opencircuit voltage with band gap in defective-zone and low-bandgap-plateau regions from Shockley-Queisser theory is captured by our models, and the former is due to the deep-level traps formed by crystallographic distortion and the latter is due to the enhanced susceptibility by increased Sn (4+ )content. The more difficulty for hole extraction than electron is also concluded in the models and the prediction curve of power conversion efficiency is in a good agreement with Shockley-Queisser limit. With the help of search and optimization algorithms, an optimized Sn:Pb composition ratio near 0.6 is finally obtained for high-performance perovskite solar cells, then verified by our experiments. Our constructive method could also be applicable to other material optimization and efficient device development.
|
|
| 8. |
- Karlsson, Max, et al.
(författare)
-
Role of chloride on the instability of blue emitting mixed-halide perovskites
- 2023
-
Ingår i: FRONTIERS OF OPTOELECTRONICS. - : HIGHER EDUCATION PRESS. - 2095-2759. ; 16:1
-
Tidskriftsartikel (refereegranskat)abstract
- Although perovskite light-emitting diodes (PeLEDs) have seen unprecedented development in device efficiency over the past decade, they suffer significantly from poor operational stability. This is especially true for blue PeLEDs, whose operational lifetime remains orders of magnitude behind their green and red counterparts. Here, we systematically investigate this efficiency-stability discrepancy in a series of green- to blue-emitting PeLEDs based on mixed Br/Cl-perovskites. We find that chloride incorporation, while having only a limited impact on efficiency, detrimentally affects device stability even in small amounts. Device lifetime drops exponentially with increasing Cl-content, accompanied by an increased rate of change in electrical properties during operation. We ascribe this phenomenon to an increased mobility of halogen ions in the mixed-halide lattice due to an increased chemically and structurally disordered landscape with reduced migration barriers. Our results indicate that the stability enhancement for PeLEDs might require different strategies from those used for improving efficiency.
|
|
| 9. |
- Pei, Y., et al.
(författare)
-
A specialized partial discretized optimization algorithm for SLL suppression in FSS design
- 2023
-
Ingår i: AIP Advances. - : AIP Publishing. - 2158-3226. ; 13:8
-
Tidskriftsartikel (refereegranskat)abstract
- Side Lobe Level (SLL) suppression is a challenging but essential part of frequency selective surface (FSS) structural design. The SLL of the radiation pattern is a key parameter demonstrating the directional anti-interference ability and mainly depends on the geometry of the FSS. However, the correlation between SLL and FSS structural parameters is extremely complicated. A minor FSS structure change may result in a drastic diversion in the sidelobes direction or level, making the SLL the most difficult parameter to optimize. In this paper, an efficient optimization method specifically for SLL suppression is proposed. We discretized the edges of split square ring FSS structures by binary representation and generated new patterns based on the genetic algorithm. Optimization results showed that in the most optimal structure, the SLL was -23.41 dB, exhibiting a 5.17 dB reduction. Meanwhile, the center frequency variation was less than 2%. Moreover, the computation time cost was reduced by over 90% compared with that of the fully discretized pattern optimization method, showing that this novel method was truly effective in getting SLL suppressed FSS structures.
|
|
| 10. |
- Pei, Yuan, et al.
(författare)
-
Dynamic algorithm for fitness function greatly improves the optimization efficiency of frequency selective surface for better design of radar
- 2022
-
Ingår i: Scientific Reports. - : Nature Portfolio. - 2045-2322. ; 12:1
-
Tidskriftsartikel (refereegranskat)abstract
- Multiple objectives optimization of frequency selective surface (FSS) structures is challenging in electromagnetic wave filter design. For example, one of the sub-objectives, the sidelobe level (SLL), is critical to directional anti-interference, which is complicated and becomes the bottleneck for radar design. Here, we established a dynamic algorithm for fitness function to automatically adjust the weights of multiple objectives in the optimization process of FSS structures. The dynamic algorithm could efficiently evaluate the achieving probability of sub-objectives according to the statistical analysis of the latest individual distribution so that the fitness function could automatically adjusted to focus on the sub-objective difficult to optimize, such as SLL. Computational results from the dynamic algorithm showed that the efficiency of multi-objective optimization was greatly improved by 213%, as compared to the fixed-weighted algorithm of the fitness function. Specifically for SLL, the efficiency rate increased even better, up to 315%. More interestingly, the FSS structures were most improved while picking median value or golden section value as the reference value. Taken together, the current study indicated that the dynamic algorithm with fitness function might be a better choice for FSS structural optimization with SLL suppression and potentially for the better design of lower SLL radar.
|
|
| 11. |
- Qin, Jiajun, et al.
(författare)
-
Aligning Transition Dipole Moment toward Light Amplification and Polarized Emission in Hybrid Perovskites
- 2021
-
Ingår i: Advanced Optical Materials. - : Wiley-V C H Verlag GMBH. - 2162-7568 .- 2195-1071. ; 9:20
-
Tidskriftsartikel (refereegranskat)abstract
- Orientational manipulation of transition dipole moment (TDM) plays an important role in controlling the polarization of excited states in light emission as well as lasing actions. The present work discovers vertically aligned TDMs in hybrid perovskite films through angle-resolved photoluminescence (PL) measurements, which show enhanced emission through the film edge. With increasing excitation intensity, the edge emission induced by these vertically aligned TDMs becomes dominant and eventually leads to amplified spontaneous emission (ASE) through the edge view. Meanwhile, polarized emission of both PL and electroluminescence (EL) provides further evidence for vertically aligned TDMs. Surprisingly, the degree of polarization (DOP) through the film edge is increased when grain boundary defects are passivated through either stochiometric engineering or self-passivation by mobile ions under working conditions. With increasing DOP, ASE threshold of the perovskite film is reduced owing to enhanced collective behaviors of light-emitting states. This work presents a useful method to manipulate TDMs in organic-inorganic hybrid perovskites.
|
|
| 12. |
- Qin, Jiajun, et al.
(författare)
-
Carrier Dynamics and Evaluation of Lasing Actions in Halide Perovskites
- 2021
-
Ingår i: TRENDS IN CHEMISTRY. - : ELSEVIER. - 2589-5974. ; 3:1, s. 34-46
-
Forskningsöversikt (refereegranskat)abstract
- Metal halide perovskites have shown rapid development in various fields such as photovoltaics, photodetectors, light-emitting diodes (LEDs), and optically pumped lasers owing to their superior optoelectronic properties. Here, we review the basic optoelectronic properties of halide perovskites from a photophysical perspective. We highlight that halide perovskites are promising in various optoelectronic devices functioning at a wide range of carrier densities. We discuss optically and electrically generated carrier density under two different excitation modes [continuous wave (CW) and pulsed] as well as the impact of carrier density on the optoelectronic behavior of perovskites. Moreover, we discuss lasing actions at high carrier densities and summarize key rules to evaluate the lasing actions. Last, we provide an outlook on perovskite-based electrically pumped lasers.
|
|
| 13. |
- Qin, Jiajun, et al.
(författare)
-
From optical pumping to electrical pumping: the threshold overestimation in metal halide perovskites
- 2023
-
Ingår i: Materials Horizons. - : ROYAL SOC CHEMISTRY. - 2051-6347 .- 2051-6355. ; 10:4, s. 1446-1453
-
Tidskriftsartikel (refereegranskat)abstract
- The threshold carrier density, conventionally evaluated from optical pumping, is a key reference parameter towards electrically pumped lasers with the widely acknowledged assumption that optically excited charge carriers relax to the band edge through an ultrafast process. However, the characteristically slow carrier cooling in perovskites challenges this assumption. Here, we investigate the optical pumping of state-of-the-art bromide- and iodine-based perovskites. We find that the threshold decreases by one order of magnitude with decreasing excitation energy from 3.10 eV to 2.48 eV for methylammonium lead bromide perovskite (MAPbBr(3)), indicating that the low-energy photon excitation facilitates faster cooling and hence enables efficient carrier accumulation for population inversion. Our results are then interpreted due to the coupling of phonon scattering in connection with the band structure of perovskites. This effect is further verified in the two-photon pumping process, where the carriers relax to the band edge with a smaller difference in phonon momentum that speeds up the carrier cooling process. Furthermore, by extrapolating the optical pumping threshold to the band edge excitation as an analog of the electrical carrier injection to the perovskite, we obtain a critical threshold carrier density of similar to 1.9 x 10(17) cm(-3), which is one order of magnitude lower than that estimated from the conventional approach. Our work thus highlights the feasibility of metal halide perovskites for electrically pumped lasers.
|
|
| 14. |
- Shen, Tangyao, et al.
(författare)
-
Giant magneto field effect in up-conversion amplified spontaneous emission via spatially extended states in organic-inorganic hybrid perovskites
- 2022
-
Ingår i: Opto-Electronic Advances. - : Editorial Office of Opto-Electronic Advances. - 2096-4579. ; 5:2
-
Tidskriftsartikel (refereegranskat)abstract
- Up-conversion lasing actions are normally difficult to realize in light-emitting materials due to small multi-photon absorption cross section and fast dephasing of excited states during multi-photon excitation. This paper reports an easily accessible up-conversion amplified spontaneous emission (ASE) in organic-inorganic hybrid perovskites (MAPbBr(3)) films by optically exciting broad gap states with sub-bandgap laser excitation. The broad absorption was optimized by adjusting the grain sizes in the MAPbBr3 films. At low sub-bandgap pumping intensities, directly exciting the gap states leads to 2-photon, 3-photon, and 4-photon up-conversion spontaneous emission, revealing a large optical cross section of multiphoton excitation occurring in such hybrid perovskite films. At moderate pumping intensity (1.19 mJ/cm(2)) of 700 nm laser excitation, a significant spectral narrowing phenomenon was observed with the full width at half maximum (FWHM) decreasing from 18 nm to 4 nm at the peak wavelength of 550 nm, simultaneously with a nonlinear increase on spectral peak intensity, showing an up-conversion ASE realized at low threshold pumping fluence. More interestingly, the up-conversion ASE demonstrated a giant magnetic field effect, leading to a magneto-ASE reaching 120%. In contrast, the upconversion photoluminescence (PL) showed a negligible magnetic field effect (< 1%). This observation provides an evidence to indicate that the light-emitting states responsible for up-conversion ASE are essentially formed as spatially extended states. The angular dependent spectrum results further verify the existence of spatially extended states which are polarized to develop coherent in-phase interaction. Clearly, using broad gap states with spatially extended light-emitting states presents a new approach to develop up-conversion ASE in organic-inorganic hybrid perovskites.
|
|
| 15. |
- Teng, Pengpeng, et al.
(författare)
-
Degradation and self-repairing in perovskite light-emitting diodes
- 2021
-
Ingår i: Matter. - : Elsevier. - 2590-2393 .- 2590-2385. ; 4:11, s. 3710-3724
-
Tidskriftsartikel (refereegranskat)abstract
- One of the most critical challenges in perovskite light-emitting diodes (PeLEDs) lies in poor operational stability. Although field dependent ion migration is believed to play an important role in the operation of perovskite optoelectronic devices, a complete understanding of how it affects the stability of PeLEDs is still missing. Here, we report a unique self-repairing behavior that the electroluminescence of moderately degraded PeLEDs can almost completely restore to their initial performance after resting. We find that the accumulated halides within the hole transport layer undergo back diffusion toward the surface of the perovskite layer during resting, repairing the vacancies and thus resulting in electroluminescence recovery. These findings indicate that one of the dominant degradation pathways in PeLEDs is the generation of halide vacancies at perovskite/hole transport layer interface during operation. We thus further passivate this key interface, which results in a high external quantum efficiency of 22.8% and obviously improved operational stability.
|
|
| 16. |
- Wang, Heyong, et al.
(författare)
-
Dynamic Redistribution of Mobile Ions in Perovskite Light-Emitting Diodes
- 2021
-
Ingår i: Advanced Functional Materials. - : WILEY-V C H VERLAG GMBH. - 1616-301X .- 1616-3028. ; 31:8
-
Tidskriftsartikel (refereegranskat)abstract
- Despite quick development of perovskite light-emitting diodes (PeLEDs) during the past few years, the fundamental mechanisms on how ion migration affects device efficiency and stability remain unclear. Here, it is demonstrated that the dynamic redistribution of mobile ions in the emissive layer plays a key role in the performance of PeLEDs and can explain a range of abnormal behaviours commonly observed during the device measurement. The dynamic redistribution of mobile ions changes charge-carrier injection and leads to increased recombination current; at the same time, the ion redistribution also changes charge transport and results in decreased shunt resistance current. As a result, the PeLEDs show hysteresis in external quantum efficiencies (EQEs) and radiance, that is, higher EQEs and radiance during the reverse voltage scan than during the forward scan. In addition, the changes on charge injection and transport induced by the ion redistribution also well explain the rise of the EQE/radiance values under constant driving voltages. The argument is further rationalized by adding extra formamidinium iodide (FAI) into optimized PeLEDs based on FAPbI(3), resulting in more significant hysteresis and shorter operational stability of the PeLEDs.
|
|
| 17. |
- Wang, Heyong, 1989-, et al.
(författare)
-
Impacts of the Lattice Strain on Perovskite Light-Emitting Diodes
- 2023
-
Ingår i: Advanced Energy Materials. - : Wiley-V C H Verlag GMBH. - 1614-6832 .- 1614-6840. ; 13:33
-
Tidskriftsartikel (refereegranskat)abstract
- The development of perovskite light-emitting diodes (PeLEDs) with both high efficiency and excellent stability remains challenging. Herein, a strong correlation between the lattice strain in perovskite films and the stability of resulting PeLEDs is revealed. Based on high-efficiency PeLEDs, the device lifetime is optimized by rationally tailoring the lattice strain in perovskite films. A PeLED with a high peak external quantum efficiency of 18.2% and a long lifetime of 151 h (T-70, under a current density of 20 mA cm(-2)) is realized with a minimized lattice strain in the perovskite film. In addition, an increase in the lattice strain is found during the long-time device stability test, indicating that the degradation of the local perovskite lattice structure could be one of the degradation mechanisms for long-term stable PeLEDs.
|
|
| 18. |
- Weng, Zhenhua, et al.
(författare)
-
Lead-Free Cs2BiAgBr6 Double Perovskite-Based Humidity Sensor with Superfast Recovery Time
- 2019
-
Ingår i: Advanced Functional Materials. - : WILEY-V C H VERLAG GMBH. - 1616-301X .- 1616-3028. ; 29:24
-
Tidskriftsartikel (refereegranskat)abstract
- Lead halide perovskites have demonstrated outstanding achievements in photoelectric applications owing to their unique properties. However, the moisture sensitivity of lead halide perovskite has rarely been developed into an applicable humidity sensor due to the intrinsic instability and toxicity issue. Herein, as a highly stable lead-free perovskite, a Cs2BiAgBr6 thin film is chosen to be the active material for humidity sensor due to its extraordinary humidity-dependent electrical properties and good stability. This Cs2BiAgBr6 thin film humidity sensor demonstrates a superfast response time (1.78 s) and recovery time (0.45 s). The superfast response and recovery properties can be attributed to the reversible physisorption of water molecules, which can be easily adsorbed onto or desorbed from the thin film surface. Moreover, the sensor also shows an excellent reliability and stability properties as well as logarithmic linearity in a relative humidity's range of 15% to 78%. The lead-free Cs2BiAgBr6 perovskite possesses great potential for application in real-time humidity sensing.
|
|
| 19. |
- Yu, Hongling, et al.
(författare)
-
Color-Stable Blue Light-Emitting Diodes Enabled by Effective Passivation of Mixed Halide Perovskites
- 2021
-
Ingår i: The Journal of Physical Chemistry Letters. - : American Chemical Society (ACS). - 1948-7185. ; 12:26, s. 6041-6047
-
Tidskriftsartikel (refereegranskat)abstract
- Bandgap tuning through mixing halide anions is one of the most attractive features for metal halide perovskites. However, mixed halide perovskites usually suffer from phase segregation under electrical biases. Herein, we obtain high-performance and color-stable blue perovskite LEDs (PeLEDs) based on mixed bromide/ chloride three-dimensional (3D) structures. We demonstrate that the color instability of CsPb(Br1-xClx)(3) PeLEDs results from surface defects at perovskite grain boundaries. By effective defect passivation, we achieve color-stable blue electroluminescence from CsPb(Br1-xClx)(3) PeLEDs, with maximum external quantum efficiencies of up to 4.5% and high luminance of up to 5351 cd m(-2) in the sky-blue region (489 nm). Our work provides new insights into the color instability issue of mixed halide perovskites and can spur new development of high-performance and color-stable blue PeLEDs.
|
|
| 20. |
- Yu, Xianxi, et al.
(författare)
-
Memory Devices via Unipolar Resistive Switching in Symmetric Organic-Inorganic Perovskite Nanoscale Heterolayers
- 2020
-
Ingår i: ACS Applied Nano Materials. - : AMER CHEMICAL SOC. - 2574-0970. ; 3:12, s. 11889-11896
-
Tidskriftsartikel (refereegranskat)abstract
- Organic-inorganic hybrid perovskite thin films with nanostructured polycrystalline grains have shown great potential in various nanoscale optoelectrical applications. Among them, the field of electrical memory has fallen behind due to insufficient knowledge of the related resistive switching characters and mechanisms. In the present work, switching behaviors of perovskite memory devices are systematically analyzed by comparing them with organic memory devices. We found that decreasing the conductivity of a polycrystalline perovskite thin layer would lead to unipolar switching behaviors, which is supplementary to the present perovskite memory family where bipolar switching is commonly reported. Moreover, our proposed symmetrical device with a nanoscale heterolayer structure enables us not only to achieve highly reproducible unipolar switching devices but also to settle the argument whether microconducting channels exist within perovskite memory devices through characterizing the microscopic morphological homogeneity. Surprisingly, the scanning electron microscopy results show that partial 10 pm large perovskite grains would be decomposed into various 100 nm small grains under high external bias, indicating the presence of microconducting channels. Furthermore, energy-dispersive X-ray spectroscopy results together with photoluminescence results of the perovskite thin film before and after applying bias are nearly identical, demonstrating that microconducting channels are formed without any difference in compositions or optical properties. Our discoveries provide a practical strategy to achieve electrical storage via organic-inorganic hybrid perovskite thin-film devices.
|
|
| 21. |
- Zhang, Jia, et al.
(författare)
-
Revealing Charge Transfer Dynamics in Methylammonium Lead Bromide Perovskites via Transient Photoluminescence Characterization
- 2022
-
Ingår i: ACS Applied Energy Materials. - : American Chemical Society (ACS). - 2574-0962. ; 5:7, s. 8084-8091
-
Tidskriftsartikel (refereegranskat)abstract
- It is an important but difficult issue to identify charge and energy transfer processes in materials where multiple band gaps coexist. Conventional methods using transient absorption and optoelectrical characterization based on devices could not provide a clear picture of transfer dynamics. According to the bimolecular and monomolecular nature of each process, the carrier dynamics is supposed to solve this issue. In this work, we established a novel, convenient and universal strategy based on the calculation of carrier dynamics to distinguish energy/charge transfer and reveal their transfer dynamics in methylammonium lead bromide (MAPbBr3) films with mixing wide-band gap small grains and narrow-band gap large grains. A highly efficient charge transfer process is confirmed with a high negative nonradiative bimolecular recombination coefficient of -2.12 x 10(-7)cm(-3) s(-1), indicating that free carriers within small grains are efficiently transferred from small grains to large grains. As a result, emission from large grains becomes dominant when increasing the photoexcitation intensity. In addition, current-density-dependent electroluminescence results in emission only from large grains, further verifying the charge transfer process. Moreover, it is interesting to find that when decreasing the size of small grains, the charge transfer process is facilitated, leading to an increased nonradiative bimolecular recombination coefficient from -2.12 x 10(-7) to -4.01 x 10(-7) cm(-3) s(-1) in large grains. Our work provides a convenient strategy to identify and quantify energy and charge transfer in metal halide perovskites, which can be used to enrich our understanding of perovskite photophysics.
|
|
| 22. |
- Zhang, Jia, et al.
(författare)
-
Transport Layer Engineering Toward Lower Threshold for Perovskite Lasers
- 2023
-
Ingår i: Advanced Materials. - : WILEY-V C H VERLAG GMBH. - 0935-9648 .- 1521-4095. ; 35:30
-
Tidskriftsartikel (refereegranskat)abstract
- Charge-transport layers are essential for achieving electrically pumped perovskite lasers. However, their role in perovskite lasing is not fully understood. Here, the role of charge-transport layers on the lasing actions of perovskite films is explored by investigating the amplified spontaneous emission (ASE) thresholds. A largely reduced ASE threshold and enhanced ASE intensity is demonstrated by introducing an additional hole transport layer poly(triaryl amine) (PTAA). It is shown that the key role of the PTAA layer is to accelerate the hot-carrier cooling process by extracting holes in perovskites. With reduced hot holes, the Auger recombination loss is largely suppressed, resulting in decreased ASE threshold. This argument is further supported by the fact that the ASE threshold can be further reduced from 25.7 to 7.2 mu J cm(-2) upon switching the pumping wavelength from 400 to 500 nm to directly avoid excess hot-hole generation. This work exemplifies how to further reduce the ASE threshold with transport layer engineering through hot-hole manipulation. This is critical to maintaining the excellent gain properties of perovskites when integrating them into electrical devices, paving the way for electrically pumped perovskite lasers.
|
|
