| 1. |
- Bombarda, F., et al.
(författare)
-
Runaway electron beam control
- 2019
-
Ingår i: Plasma Physics and Controlled Fusion. - : IOP Publishing. - 1361-6587 .- 0741-3335. ; 61:1
-
Tidskriftsartikel (refereegranskat)
|
|
| 2. |
- Joffrin, E., et al.
(författare)
-
Overview of the JET preparation for deuterium-tritium operation with the ITER like-wall
- 2019
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 59:11
-
Forskningsöversikt (refereegranskat)abstract
- For the past several years, the JET scientific programme (Pamela et al 2007 Fusion Eng. Des. 82 590) has been engaged in a multi-campaign effort, including experiments in D, H and T, leading up to 2020 and the first experiments with 50%/50% D-T mixtures since 1997 and the first ever D-T plasmas with the ITER mix of plasma-facing component materials. For this purpose, a concerted physics and technology programme was launched with a view to prepare the D-T campaign (DTE2). This paper addresses the key elements developed by the JET programme directly contributing to the D-T preparation. This intense preparation includes the review of the physics basis for the D-T operational scenarios, including the fusion power predictions through first principle and integrated modelling, and the impact of isotopes in the operation and physics of D-T plasmas (thermal and particle transport, high confinement mode (H-mode) access, Be and W erosion, fuel recovery, etc). This effort also requires improving several aspects of plasma operation for DTE2, such as real time control schemes, heat load control, disruption avoidance and a mitigation system (including the installation of a new shattered pellet injector), novel ion cyclotron resonance heating schemes (such as the three-ions scheme), new diagnostics (neutron camera and spectrometer, active Alfven eigenmode antennas, neutral gauges, radiation hard imaging systems...) and the calibration of the JET neutron diagnostics at 14 MeV for accurate fusion power measurement. The active preparation of JET for the 2020 D-T campaign provides an incomparable source of information and a basis for the future D-T operation of ITER, and it is also foreseen that a large number of key physics issues will be addressed in support of burning plasmas.
|
|
| 3. |
|
|
| 4. |
|
|
| 5. |
-
- 2018
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 58:1
-
Forskningsöversikt (refereegranskat)
|
|
| 6. |
|
|
| 7. |
|
|
| 8. |
- Krasilnikov, A., et al.
(författare)
-
Evidence of 9 Be + p nuclear reactions during 2ω CH and hydrogen minority ICRH in JET-ILW hydrogen and deuterium plasmas
- 2018
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 58:2
-
Tidskriftsartikel (refereegranskat)abstract
- The intensity of 9Be + p nuclear fusion reactions was experimentally studied during second harmonic (2ω CH) ion-cyclotron resonance heating (ICRH) and further analyzed during fundamental hydrogen minority ICRH of JET-ILW hydrogen and deuterium plasmas. In relatively low-density plasmas with a high ICRH power, a population of fast H+ ions was created and measured by neutral particle analyzers. Primary and secondary nuclear reaction products, due to 9Be + p interaction, were observed with fast ion loss detectors, γ-ray spectrometers and neutron flux monitors and spectrometers. The possibility of using 9Be(p, d)2α and 9Be(p, α)6Li nuclear reactions to create a population of fast alpha particles and study their behaviour in non-active stage of ITER operation is discussed in the paper.
|
|
| 9. |
|
|
| 10. |
|
|
| 11. |
|
|
| 12. |
|
|
| 13. |
|
|
| 14. |
|
|
| 15. |
|
|
| 16. |
|
|
| 17. |
|
|
| 18. |
|
|
| 19. |
|
|
| 20. |
|
|
| 21. |
|
|
| 22. |
|
|
| 23. |
|
|
| 24. |
|
|
| 25. |
-
Overview of the JET results
- 2015
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 0029-5515 .- 1741-4326. ; 55:10
-
Tidskriftsartikel (refereegranskat)
|
|
| 26. |
|
|
| 27. |
-
- 2018
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 58:9
-
Tidskriftsartikel (refereegranskat)
|
|
| 28. |
- Abel, I, et al.
(författare)
-
Overview of the JET results with the ITER-like wall
- 2013
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 53:10, s. 104002-
-
Tidskriftsartikel (refereegranskat)abstract
- Following the completion in May 2011 of the shutdown for the installation of the beryllium wall and the tungsten divertor, the first set of JET campaigns have addressed the investigation of the retention properties and the development of operational scenarios with the new plasma-facing materials. The large reduction in the carbon content (more than a factor ten) led to a much lower Z(eff) (1.2-1.4) during L- and H-mode plasmas, and radiation during the burn-through phase of the plasma initiation with the consequence that breakdown failures are almost absent. Gas balance experiments have shown that the fuel retention rate with the new wall is substantially reduced with respect to the C wall. The re-establishment of the baseline H-mode and hybrid scenarios compatible with the new wall has required an optimization of the control of metallic impurity sources and heat loads. Stable type-I ELMy H-mode regimes with H-98,H-y2 close to 1 and beta(N) similar to 1.6 have been achieved using gas injection. ELM frequency is a key factor for the control of the metallic impurity accumulation. Pedestal temperatures tend to be lower with the new wall, leading to reduced confinement, but nitrogen seeding restores high pedestal temperatures and confinement. Compared with the carbon wall, major disruptions with the new wall show a lower radiated power and a slower current quench. The higher heat loads on Be wall plasma-facing components due to lower radiation made the routine use of massive gas injection for disruption mitigation essential.
|
|
| 29. |
- Romanelli, F, et al.
(författare)
-
Overview of the JET results
- 2011
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 51:9
-
Tidskriftsartikel (refereegranskat)abstract
- Since the last IAEA Conference JET has been in operation for one year with a programmatic focus on the qualification of ITER operating scenarios, the consolidation of ITER design choices and preparation for plasma operation with the ITER-like wall presently being installed in JET. Good progress has been achieved, including stationary ELMy H-mode operation at 4.5 MA. The high confinement hybrid scenario has been extended to high triangularity, lower ρ*and to pulse lengths comparable to the resistive time. The steady-state scenario has also been extended to lower ρ*and ν*and optimized to simultaneously achieve, under stationary conditions, ITER-like values of all other relevant normalized parameters. A dedicated helium campaign has allowed key aspects of plasma control and H-mode operation for the ITER non-activated phase to be evaluated. Effective sawtooth control by fast ions has been demonstrated with3He minority ICRH, a scenario with negligible minority current drive. Edge localized mode (ELM) control studies using external n = 1 and n = 2 perturbation fields have found a resonance effect in ELM frequency for specific q95values. Complete ELM suppression has, however, not been observed, even with an edge Chirikov parameter larger than 1. Pellet ELM pacing has been demonstrated and the minimum pellet size needed to trigger an ELM has been estimated. For both natural and mitigated ELMs a broadening of the divertor ELM-wetted area with increasing ELM size has been found. In disruption studies with massive gas injection up to 50% of the thermal energy could be radiated before, and 20% during, the thermal quench. Halo currents could be reduced by 60% and, using argon/deuterium and neon/deuterium gas mixtures, runaway electron generation could be avoided. Most objectives of the ITER-like ICRH antenna have been demonstrated; matching with closely packed straps, ELM resilience, scattering matrix arc detection and operation at high power density (6.2 MW m-2) and antenna strap voltages (42 kV). Coupling measurements are in very good agreement with TOPICA modelling. © 2011 IAEA, Vienna.
|
|
| 30. |
- Murari, A., et al.
(författare)
-
A control oriented strategy of disruption prediction to avoid the configuration collapse of tokamak reactors
- 2024
-
Ingår i: Nature Communications. - 2041-1723 .- 2041-1723. ; 15:1
-
Tidskriftsartikel (refereegranskat)abstract
- The objective of thermonuclear fusion consists of producing electricity from the coalescence of light nuclei in high temperature plasmas. The most promising route to fusion envisages the confinement of such plasmas with magnetic fields, whose most studied configuration is the tokamak. Disruptions are catastrophic collapses affecting all tokamak devices and one of the main potential showstoppers on the route to a commercial reactor. In this work we report how, deploying innovative analysis methods on thousands of JET experiments covering the isotopic compositions from hydrogen to full tritium and including the major D-T campaign, the nature of the various forms of collapse is investigated in all phases of the discharges. An original approach to proximity detection has been developed, which allows determining both the probability of and the time interval remaining before an incoming disruption, with adaptive, from scratch, real time compatible techniques. The results indicate that physics based prediction and control tools can be developed, to deploy realistic strategies of disruption avoidance and prevention, meeting the requirements of the next generation of devices.
|
|
| 31. |
|
|
| 32. |
|
|
| 33. |
|
|
| 34. |
- Meyer, H.F., et al.
(författare)
-
Overview of physics studies on ASDEX Upgrade
- 2019
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 59:11
-
Forskningsöversikt (refereegranskat)abstract
- The ASDEX Upgrade (AUG) programme, jointly run with the EUROfusion MST1 task force, continues to significantly enhance the physics base of ITER and DEMO. Here, the full tungsten wall is a key asset for extrapolating to future devices. The high overall heating power, flexible heating mix and comprehensive diagnostic set allows studies ranging from mimicking the scrape-off-layer and divertor conditions of ITER and DEMO at high density to fully non-inductive operation (q 95 = 5.5, ) at low density. Higher installed electron cyclotron resonance heating power 6 MW, new diagnostics and improved analysis techniques have further enhanced the capabilities of AUG. Stable high-density H-modes with MW m-1 with fully detached strike-points have been demonstrated. The ballooning instability close to the separatrix has been identified as a potential cause leading to the H-mode density limit and is also found to play an important role for the access to small edge-localized modes (ELMs). Density limit disruptions have been successfully avoided using a path-oriented approach to disruption handling and progress has been made in understanding the dissipation and avoidance of runaway electron beams. ELM suppression with resonant magnetic perturbations is now routinely achieved reaching transiently . This gives new insight into the field penetration physics, in particular with respect to plasma flows. Modelling agrees well with plasma response measurements and a helically localised ballooning structure observed prior to the ELM is evidence for the changed edge stability due to the magnetic perturbations. The impact of 3D perturbations on heat load patterns and fast-ion losses have been further elaborated. Progress has also been made in understanding the ELM cycle itself. Here, new fast measurements of and E r allow for inter ELM transport analysis confirming that E r is dominated by the diamagnetic term even for fast timescales. New analysis techniques allow detailed comparison of the ELM crash and are in good agreement with nonlinear MHD modelling. The observation of accelerated ions during the ELM crash can be seen as evidence for the reconnection during the ELM. As type-I ELMs (even mitigated) are likely not a viable operational regime in DEMO studies of 'natural' no ELM regimes have been extended. Stable I-modes up to have been characterised using -feedback. Core physics has been advanced by more detailed characterisation of the turbulence with new measurements such as the eddy tilt angle - measured for the first time - or the cross-phase angle of and fluctuations. These new data put strong constraints on gyro-kinetic turbulence modelling. In addition, carefully executed studies in different main species (H, D and He) and with different heating mixes highlight the importance of the collisional energy exchange for interpreting energy confinement. A new regime with a hollow profile now gives access to regimes mimicking aspects of burning plasma conditions and lead to nonlinear interactions of energetic particle modes despite the sub-Alfvénic beam energy. This will help to validate the fast-ion codes for predicting ITER and DEMO.
|
|
| 35. |
- Stroth, U., et al.
(författare)
-
Progress from ASDEX Upgrade experiments in preparing the physics basis of ITER operation and DEMO scenario development
- 2022
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 62:4
-
Tidskriftsartikel (refereegranskat)abstract
- An overview of recent results obtained at the tokamak ASDEX Upgrade (AUG) is given. A work flow for predictive profile modelling of AUG discharges was established which is able to reproduce experimental H-mode plasma profiles based on engineering parameters only. In the plasma center, theoretical predictions on plasma current redistribution by a dynamo effect were confirmed experimentally. For core transport, the stabilizing effect of fast ion distributions on turbulent transport is shown to be important to explain the core isotope effect and improves the description of hollow low-Z impurity profiles. The L-H power threshold of hydrogen plasmas is not affected by small helium admixtures and it increases continuously from the deuterium to the hydrogen level when the hydrogen concentration is raised from 0 to 100%. One focus of recent campaigns was the search for a fusion relevant integrated plasma scenario without large edge localised modes (ELMs). Results from six different ELM-free confinement regimes are compared with respect to reactor relevance: ELM suppression by magnetic perturbation coils could be attributed to toroidally asymmetric turbulent fluctuations in the vicinity of the separatrix. Stable improved confinement mode plasma phases with a detached inner divertor were obtained using a feedback control of the plasma β. The enhanced D α H-mode regime was extended to higher heating power by feedback controlled radiative cooling with argon. The quasi-coherent exhaust regime was developed into an integrated scenario at high heating power and energy confinement, with a detached divertor and without large ELMs. Small ELMs close to the separatrix lead to peeling-ballooning stability and quasi continuous power exhaust. Helium beam density fluctuation measurements confirm that transport close to the separatrix is important to achieve the different ELM-free regimes. Based on separatrix plasma parameters and interchange-drift-Alfvén turbulence, an analytic model was derived that reproduces the experimentally found important operational boundaries of the density limit and between L- and H-mode confinement. Feedback control for the X-point radiator (XPR) position was established as an important element for divertor detachment control. Stable and detached ELM-free phases with H-mode confinement quality were obtained when the XPR was moved 10 cm above the X-point. Investigations of the plasma in the future flexible snow-flake divertor of AUG by means of first SOLPS-ITER simulations with drifts activated predict beneficial detachment properties and the activation of an additional strike point by the drifts.
|
|
| 36. |
- Gonze, X., et al.
(författare)
-
Recent developments in the ABINIT software package
- 2016
-
Ingår i: Computer Physics Communications. - : Elsevier BV. - 0010-4655. ; 205, s. 106-131
-
Tidskriftsartikel (refereegranskat)abstract
- ABINIT is a package whose main program allows one to find the total energy, charge density, electronic structure and many other properties of systems made of electrons and nuclei, (molecules and periodic solids) within Density Functional Theory (DFT), Many-Body Perturbation Theory (GW approximation and Bethe-Salpeter equation) and Dynamical Mean Field Theory (DMFT). ABINIT also allows to optimize the geometry according to the DFT forces and stresses, to perform molecular dynamics simulations using these forces, and to generate dynamical matrices, Born effective charges and dielectric tensors. The present paper aims to describe the new capabilities of ABINIT that have been developed since 2009. It covers both physical and technical developments inside the ABINIT code, as well as developments provided within the ABINIT package. The developments are described with relevant references, input variables, tests and tutorials. Program summary: . Program title: ABINIT. . Catalogue identifier: AEEU_v2_0. . Program summary URL: . http://cpc.cs.qub.ac.uk/summaries/AEEU_v2_0.html . . Program obtainable from: CPC Program Library, Queen's University, Belfast, N. Ireland. . Licensing provisions: GNU General Public License, version 3. . No. of lines in distributed program, including test data, etc.: 4845789. . No. of bytes in distributed program, including test data, etc.: 71340403. . Distribution format: tar.gz. . Programming language: Fortran2003, PERL scripts, Python scripts. . Classification: 7.3, 7.8. . External routines: (all optional) BigDFT [2], ETSF_IO [3], libxc [4], NetCDF [5], MPI [6], Wannier90 [7], FFTW [8]. . Catalogue identifier of previous version: AEEU_v1_0. . Journal reference of previous version: Comput. Phys. Comm. 180 (2009) 2582. . Does the new version supersede the previous version?: Yes. The abinit-7.10.5 version is now the up to date stable version of ABINIT. . Nature of problem: . This package has the purpose of computing accurately material and nanostructure properties: electronic structure, bond lengths, bond angles, primitive cell size, cohesive energy, dielectric properties, vibrational properties, elastic properties, optical properties, magnetic properties, non-linear couplings, electronic and vibrational life-times, and others. . Solution method: . Software application based on Density Functional Theory, Many-Body Perturbation Theory and Dynamical Mean Field Theory, pseudopotentials, with plane waves or wavelets as basis functions. . Reasons for new version: . Since 2009, the abinit-5.7.4 version of the code has considerably evolved and is not yet up to date. The abinit- 7.10.5 version contains new physical and technical features that allow electronic structure calculations impossible to carry out in the previous versions. . Summary of revisions: . •new physical features: quantum effects for the nuclei treated by the Path-integral Molecular Dynamics; finding transition states using image dynamics (NEB or string methods); two component DFT for electron-positron annihilation; linear response in a Projector Augmented-Wave approach -PAW-, electron-phonon interactions and temperature dependence of the gap; Bethe Salpeter Equation -BSE-; Dynamical Mean Field Theory (DMFT).•new technical features: development of a PAW approach for a wavelet basis; parallelisation of the code on more than 10,000 processors; new build system.•new features in the ABINIT package: tests; test farm; new tutorials; new pseudopotentials and PAW atomic data tables; GUI and postprocessing tools like the AbiPy and APPA libraries. . Running time: . It is difficult to answer to the question as the use of ABINIT is very large. On one hand, ABINIT can run on 10,000 processors for hours to perform quantum molecular dynamics on large systems. On the other hand, tutorials for students can be performed on a laptop within a few minutes. . References: . 1 http://www.gnu.org/copyleft/gpl.txt 2 http://bigdft.org 3 http://www.etsf.eu/fileformats 4 http://www.tddft.org/programs/octopus/wiki/index.php/Libxc 5 http://www.unidata.ucar.edu/software/netcdf 6 https://en.wikipedia.org/wiki/Message_Passing_Interface 7 http://www.wannier.org 8M. Frigo and S.G. Johnson, Proceedings of the IEEE, 93, 216-231 (2005). . .
|
|
| 37. |
- Litaudon, X., et al.
(författare)
-
14 MeV calibration of JET neutron detectors-phase 1: Calibration and characterization of the neutron source
- 2018
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 58:2
-
Tidskriftsartikel (refereegranskat)abstract
- In view of the planned DT operations at JET, a calibration of the JET neutron monitors at 14 MeV neutron energy is needed using a 14 MeV neutron generator deployed inside the vacuum vessel by the JET remote handling system. The target accuracy of this calibration is 10% as also required by ITER, where a precise neutron yield measurement is important, e.g. for tritium accountancy. To achieve this accuracy, the 14 MeV neutron generator selected as the calibration source has been fully characterised and calibrated prior to the in-vessel calibration of the JET monitors. This paper describes the measurements performed using different types of neutron detectors, spectrometers, calibrated long counters and activation foils which allowed us to obtain the neutron emission rate and the anisotropy of the neutron generator, i.e.The neutron flux and energy spectrum dependence on emission angle, and to derive the absolute emission rate in 4π sr. The use of high resolution diamond spectrometers made it possible to resolve the complex features of the neutron energy spectra resulting from the mixed D/T beam ions reacting with the D/T nuclei present in the neutron generator target. As the neutron generator is not a stable neutron source, several monitoring detectors were attached to it by means of an ad hoc mechanical structure to continuously monitor the neutron emission rate during the in-vessel calibration. These monitoring detectors, two diamond diodes and activation foils, have been calibrated in terms of neutrons/counts within ± 5% total uncertainty. A neutron source routine has been developed, able to produce the neutron spectra resulting from all possible reactions occurring with the D/T ions in the beam impinging on the Ti D/T target. The neutron energy spectra calculated by combining the source routine with a MCNP model of the neutron generator have been validated by the measurements. These numerical tools will be key in analysing the results from the in-vessel calibration and to derive the response of the JET neutron detectors to DT plasma neutrons starting from the response to the generator neutrons, and taking into account all the calibration circumstances.
|
|
| 38. |
- Maggi, C. F., et al.
(författare)
-
Isotope identity experiments in JET-ILW with H and D L-mode plasmas
- 2019
-
Ingår i: Nuclear Fusion. - : Institute of Physics Publishing (IOPP). - 0029-5515 .- 1741-4326. ; 59:7
-
Tidskriftsartikel (refereegranskat)abstract
- NBI-heated L-mode plasmas have been obtained in JET with the Be/W ITER-like wall (JET-ILW) in H and D, with matched profiles of the dimensionless plasma parameters, rho*, nu*, beta and q in the plasma core confinement region and same T-i/T-e and Z(eff). The achieved isotope identity indicates that the confinement scale invariance principle is satisfied in the core confinement region of these plasmas, where the dominant instabilities are Ion Temperature Gradient (ITG) modes. The dimensionless thermal energy confinement time, Omega(i) tau(E,th), and the scaled core plasma heat diffusivity, A chi(eff)/B-T, are identical in H and D within error bars, indicating lack of isotope mass dependence of the dimensionless L-mode thermal energy confinement time in JET-ILW. Predictive flux driven simulations with JETTO-TGLF of the H and D identity pair is in very good agreement with experiment for both isotopes: the stiff core heat transport, typical of JET-ILW NBI heated L-modes, overcomes the local gyro-Bohm scaling of gradient-driven TGLF, explaining the lack of isotope mass dependence in the confinement region of these plasmas. The effect of E x B shearing on the predicted heat and particle transport channels is found to be negligible for these low beta and low momentum input plasmas.
|
|
| 39. |
- Pegourie, B., et al.
(författare)
-
Deuterium inventory in Tore Supra : Coupled carbon-deuterium balance
- 2013
-
Ingår i: Journal of Nuclear Materials. - : Elsevier BV. - 0022-3115 .- 1873-4820. ; 438:Suppl., s. S120-S125
-
Tidskriftsartikel (refereegranskat)abstract
- This paper presents an analysis of the carbon-deuterium circulation and the resulting balance in Tore Supra over the period 2002-2007. Carbon balance combines the estimation of carbon gross erosion from spectroscopy, net erosion and deposition using confocal microscopy, lock-in thermography and SEM, and a measure of the amount of deposits collected in the vacuum chamber. Fuel retention is determined from post-mortem (PM) analyses and gas balance (GB) measurements. Special attention was paid to the deuterium outgassed during the nights and weekends of the experimental campaign (vessel under vacuum, Plasma Facing Components at 120 degrees C) and during vents (vessel at atmospheric pressure, PFCs at room temperature). It is shown that this outgassing is the main process reconciling the PM and GB estimations of fuel retention, closing the coupled carbon-deuterium balance. In particular, it explains why the deuterium concentration in deposits decreases with increasing depth.
|
|
| 40. |
|
|
| 41. |
- Baron-Wiechec, A., et al.
(författare)
-
Global erosion and deposition patterns in JET with the ITER-like wall
- 2015
-
Ingår i: Journal of Nuclear Materials. - : Elsevier BV. - 0022-3115 .- 1873-4820. ; 463, s. 157-161
-
Tidskriftsartikel (refereegranskat)abstract
- A set of Be and W tiles removed after the first ITER-like wall campaigns (JET-ILW) from 2011 to 2012 has been analysed. The results indicate that the primary erosion site is in the main chamber (Be) as in previous carbon campaigns (JET-C). In particular the limiters tiles near the mid-plane are eroded probably during the limiter phases of discharges. W is found at low concentrations on all plasma-facing surfaces of the vessel indicating deposition via plasma transport initially from the W divertor and from main chamber W-coated tiles; there are also traces of Mo (used as an interlayer for these coatings). Deposited films in the inner divertor have a layered structure, and every layer is dominated by Be with some W and O content.
|
|
| 42. |
- Brezinsek, S., et al.
(författare)
-
Beryllium migration in JET ITER-like wall plasmas
- 2015
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 0029-5515 .- 1741-4326. ; 55:6
-
Tidskriftsartikel (refereegranskat)abstract
- JET is used as a test bed for ITER, to investigate beryllium migration which connects the lifetime of first-wall components under erosion with tokamak safety, in relation to long-term fuel retention. The (i) limiter and the (ii) divertor configurations have been studied in JET-ILW (JET with a Be first wall and W divertor), and compared with those for the former JET-C (JET with carbon-based plasma-facing components (PFCs)). (i) For the limiter configuration, the Be gross erosion at the contact point was determined in situ by spectroscopy as between 4% (E-in = 35 eV) and more than 100%, caused by Be self-sputtering (E-in = 200 eV). Chemically assisted physical sputtering via BeD release has been identified to contribute to the effective Be sputtering yield, i.e. at E-in = 75 eV, erosion was enhanced by about 1/3 with respect to the bare physical sputtering case. An effective gross yield of 10% is on average representative for limiter plasma conditions, whereas a factor of 2 difference between the gross erosion and net erosion, determined by post-mortem analysis, was found. The primary impurity source in the limiter configuration in JET-ILW is only 25% higher (in weight) than that for the JET-C case. The main fraction of eroded Be stays within the main chamber. (ii) For the divertor configuration, neutral Be and BeD from physically and chemically assisted physical sputtering by charge exchange neutrals and residual ion flux at the recessed wall enter the plasma, ionize and are transported by scrape-off layer flows towards the inner divertor where significant net deposition takes place. The amount of Be eroded at the first wall (21 g) and the Be amount deposited in the inner divertor (28 g) are in fair agreement, though the balancing is as yet incomplete due to the limited analysis of PFCs. The primary impurity source in the JET-ILW is a factor of 5.3 less in comparison with that for JET-C, resulting in lower divertor material deposition, by more than one order of magnitude. Within the divertor, Be performs far fewer re-erosion and transport steps than C due to an energetic threshold for Be sputtering, and inhibits as a result of this the transport to the divertor floor and the pump duct entrance. The target plates in the JET-ILW inner divertor represent at the strike line a permanent net erosion zone, in contrast to the net deposition zone in JET-C with thick carbon deposits on the CFC (carbon-fibre composite) plates. The Be migration identified is consistent with the observed low long-term fuel retention and dust production with the JET-ILW.
|
|
| 43. |
- Brezinsek, S., et al.
(författare)
-
Overview of experimental preparation for the ITER-Like Wall at JET
- 2011
-
Ingår i: Journal of Nuclear Materials. - : Elsevier BV. - 0022-3115 .- 1873-4820. ; 415:1, s. S936-S942
-
Tidskriftsartikel (refereegranskat)abstract
- Experiments in JET with carbon-based plasma-facing components have been carried out in preparation of the ITER-Like Wall with beryllium main chamber and full tungsten divertor. The preparatory work was twofold: (i) development of techniques, which ensure safe operation with the new wall and (ii) provision of reference plasmas, which allow a comparison of operation with carbon and metallic wall. (i) Compatibility with the W divertor with respect to energy loads could be achieved in N-2 seeded plasmas at high densities and low temperatures, finally approaching partial detachment, with only moderate confinement reduction of 10%. Strike-point sweeping increases the operational space further by re-distributing the load over several components. (ii) Be and C migration to the divertor has been documented with spectroscopy and QMBs under different plasma conditions providing a database which will allow a comparison of the material transport to remote areas with metallic walls. Fuel retention rates of 1.0-2.0 x 10(21) D s(-1) were obtained as references in accompanied gas balance studies.
|
|
| 44. |
- Cannas, Barbara, et al.
(författare)
-
Recurrence Plots for Dynamic Analysis of Type-I ELMs at JET With a Carbon Wall
- 2019
-
Ingår i: IEEE Transactions on Plasma Science. - : Institute of Electrical and Electronics Engineers (IEEE). - 0093-3813 .- 1939-9375. ; 47:4, s. 1871-1877
-
Tidskriftsartikel (refereegranskat)abstract
- In this paper, the dynamic characteristics of type-I edge-localized modes (ELM) time series from the JET tokamak, the world's largest magnetic confinement plasma physics experiment, have been investigated through recurrence plots (RPs). The analysis has been focused on RPs of pedestal temperature, line averaged electron density, and outer divertor D-alpha time series during experiments with a carbon wall. The analysis of RPS shows the patterns similar to those characteristics of signals exhibiting type-2 intermittency, in particular, a characteristic kite-like shape; this gives useful hints to model the temperature signal as well as the D-alpha radiation time series, with simple nonlinear maps capturing the nearly periodic behavior of type-I ELMs.
|
|
| 45. |
- Citrin, J., et al.
(författare)
-
Tractable flux-driven temperature, density, and rotation profile evolution with the quasilinear gyrokinetic transport model QuaLiKiz
- 2017
-
Ingår i: Plasma Physics and Controlled Fusion. - : IOP Publishing. - 1361-6587 .- 0741-3335. ; 59:12
-
Tidskriftsartikel (refereegranskat)abstract
- Quasilinear turbulent transport models are a successful tool for prediction of core tokamak plasma profiles in many regimes. Their success hinges on the reproduction of local nonlinear gyrokinetic fluxes. We focus on significant progress in the quasilinear gyrokinetic transport model QuaLiKiz (Bourdelle et al 2016 Plasma Phys. Control. Fusion 58 014036), which employs an approximated solution of the mode structures to significantly speed up computation time compared to full linear gyrokinetic solvers. Optimisation of the dispersion relation solution algorithm within integrated modelling applications leads to flux calculations x 10(6-7) faster than local nonlinear simulations. This allows tractable simulation of flux-driven dynamic profile evolution including all transport channels: ion and electron heat, main particles, impurities, and momentum. Furthermore, QuaLiKiz now includes the impact of rotation and temperature anisotropy induced poloidal asymmetry on heavy impurity transport, important for W-transport applications. Application within the JETTO integrated modelling code results in 1 s of JET plasma simulation within 10 h using 10 CPUs. Simultaneous predictions of core density, temperature, and toroidal rotation profiles for both JET hybrid and baseline experiments are
|
|
| 46. |
- Garzotti, L., et al.
(författare)
-
Scenario development for D-T operation at JET
- 2019
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 0029-5515 .- 1741-4326. ; 59:7
-
Tidskriftsartikel (refereegranskat)abstract
- The JET exploitation plan foresees D-T operations in 2020 (DTE2). With respect to the first D-T campaign in 1997 (DTE1), when JET was equipped with a carbon wall, the experiments will be conducted in presence of a beryllium-tungsten ITER-like wall and will benefit from an extended and improved set of diagnostics and higher additional heating power (32 MW neutral beam injection + 8 MW ion cyclotron resonance heating). There are several challenges presented by operations with the new wall: a general deterioration of the pedestal confinement; the risk of heavy impurity accumulation in the core, which, if not controlled, can cause the radiative collapse of the discharge; the requirement to protect the divertor from excessive heat loads, which may damage it permanently. Therefore, an intense activity of scenario development has been undertaken at JET during the last three years to overcome these difficulties and prepare the plasmas needed to demonstrate stationary high fusion performance and clear alpha particle effects. The paper describes the status and main achievements of this scenario development activity, both from an operational and plasma physics point of view.
|
|
| 47. |
- Louche, F., et al.
(författare)
-
Design of an ICRF system for plasma-wall interactions and RF plasma production studies on TOMAS
- 2017
-
Ingår i: Fusion engineering and design. - : ELSEVIER SCIENCE SA. - 0920-3796 .- 1873-7196. ; 123, s. 317-320
-
Tidskriftsartikel (refereegranskat)abstract
- Ion cyclotron wall conditioning (ICWC) is being developed for ITER and W7-X as a baseline conditioning technique in which the ion cyclotron heating and current drive system will be employed to produce and sustain the currentless conditioning plasma. The TOMAS project (TOroidal MAgnetized System, operated at the FZ-juelich, Germany) proposes to explore several key aspects of ICWC. For this purpose we have designed an ICRF system made of a single strap antenna within a metallic box, connected to a feeding port and a pre-matching system. We discuss the design work of the antenna system with the help of the commercial electromagnetic software CST Microwave Studio (R). The simulation results for a given geometry provide input impedance matrices for the two-port system. These matrices are afterwards inserted into various circuit models to assess the accessibility of the required frequency range. The sensitivity of the matching system to uncertainties on plasma loading and capacitance values is notably addressed. With a choice of three variable capacitors we show that the system can cope with such uncertainties. We also demonstrate that the system can cope as well with the high reflected power levels during the short breakdown phase of the RF discharge, but at the cost of a significantly reduced coupled power.
|
|
| 48. |
- Matthews, G. F., et al.
(författare)
-
JET ITER-like wall-overview and experimental programme
- 2011
-
Ingår i: Physica Scripta. - : Institute of Physics Publishing (IOPP). - 0031-8949 .- 1402-4896. ; T145, s. 014001-
-
Tidskriftsartikel (refereegranskat)abstract
- This paper reports the successful installation of the JET ITER-like wall and the realization of its technical objectives. It also presents an overview of the planned experimental programme which has been optimized to exploit the new wall and other JET enhancements in 2011/12.
|
|
| 49. |
- Orsitto, F. P., et al.
(författare)
-
Approximate analytic expressions using Stokes model for tokamak polarimetry and their range of validity
- 2019
-
Ingår i: Plasma Physics and Controlled Fusion. - : IOP PUBLISHING LTD. - 0741-3335 .- 1361-6587. ; 61:5
-
Tidskriftsartikel (refereegranskat)abstract
- The analysis of the polarimetry measurements has the aim of validating models (De Marco and Segre 1972 Plasma Phys. 14 245), with a careful attention to the clarification of their limits of application. In this paper a new approximation method is introduced, the so-called special constant Omega direction (SCOD), which gives an analytical solution to the polarimetry exact Stokes model equations. The available approximate solutions (including SCOD) of the polarimetry propagation equations are presented, compared and their application limits determined, using a reference tokamak configuration, which is a simplified equilibrium for a circular tokamak. The SCOD approximation is compared successfully to the Stokes model in the context also of equilibria evaluated for two JET discharges. The approximation methods are analytical or very simple mathematical expressions which can also be used in equilibrium codes for their optimization.
|
|
| 50. |
- Tsitrone, E., et al.
(författare)
-
Multi machine scaling of fuel retention in 4 carbon dominated tokamaks
- 2011
-
Ingår i: Journal of Nuclear Materials. - : Elsevier BV. - 0022-3115 .- 1873-4820. ; 415:1, s. S735-S739
-
Tidskriftsartikel (refereegranskat)abstract
- In order to benchmark predictions for the in vessel tritium inventory in ITER, a survey of fuel retention measured in 4 carbon dominated tokamaks (TEXTOR, ASDEX Upgrade in the 2002-2003 carbon configuration, Tore Supra and JET) was performed, showing retention rates from similar to 1 g D/h in TEXTOR (L mode, limiter machine) up to similar to 6-12 g D/h in AUG (H mode, divertor machine). A simple scaling used for ITER predictions is applied for comparison with experimental values: (1) estimate of wall fluxes, (2) estimate of the gross carbon erosion, (3) estimate of the net erosion/redeposition assuming a redeposition fraction and (4) estimate of the retention rate using D/C ratio scalings. The validity of each step is discussed, showing that this approach yields the right order of magnitude, but tends to underestimate the experimental values unless a high wall flux, a low local redeposition fraction and/or a high D/C ratio are used.
|
|
