| 1. |
- Ullah, Muhammad Kaleem, et al.
(författare)
-
Tri-doped ceria (M0.2Ce0.8O2-δ, M= Sm0.1 Ca0.05 Gd0.05) electrolyte for hydrogen and ethanol-based fuel cells
- 2019
-
Ingår i: Journal of Alloys and Compounds. - : Elsevier BV. - 0925-8388. ; 773, s. 548-554
-
Tidskriftsartikel (refereegranskat)abstract
- In recent scientific research, an interest has been gained significantly by rare earth metals such as cerium (Ce), samarium (Sm) and gadolinium (Gd) due to their use in fuel cells as electrolyte and catalysts. When used in an electrolyte, these materials lower the fuel cell's operating temperature compared to a conventional electrolyte, for example, yittria-stabilized zirconia (YSZ) which operates at a high temperature (≥800 °C). In this paper, the tri-doped ceria, M0.2Ce0.8O2-δ(M = Sm0.1Ca0.05Gd0.05) electrolyte powders was synthesized using the co-precipitation method at 80 °C. These dopants were used for CeO2with a total molar ratio of 1 M. Dry-pressed powder technique was used to make fuel cell pellets from the powder and placed them in the furnace to sinter at 700 °C for 60 min. Electrical conductivity of such a pellet in air was 1.2 × 10−2S cm−1at 700 °C measured by the ProboStat-NorECs setup. The crystal structure was determined with the help of X-ray diffraction (XRD), which showed that all the dopants were successfully doped in CeO2. Raman spectroscopy and UV-VIS spectroscopy were also carried out to analyse the molecular vibrations and absorbance, respectively. The maximum open-circuit voltages (OCVs) for hydrogen and ethanol fuelled at 550 °C were observed to be 0.89 V and 0.71 V with power densities 314 mW cm−2and 52.8 mW cm−2, respectively.
|
|
| 2. |
|
|
| 3. |
- Ali, Amjad, et al.
(författare)
-
Electrochemical study of composite materials for coal-based direct carbon fuel cell
- 2018
-
Ingår i: International journal of hydrogen energy. - : Elsevier. - 0360-3199 .- 1879-3487. ; 43:28, s. 12900-12908
-
Tidskriftsartikel (refereegranskat)abstract
- The efficient conversion of solid carbon fuels into energy by reducing the emission of harmful gases is important for clean environment. In this regards, direct carbon fuel cell (DCFC) is a system that converts solid carbon directly into electrical energy with high thermodynamic efficiency (100%), system efficiency of 80% and half emission of gases compared to conventional coal power plants. This can generate electricity from any carbonaceous fuel such as charcoal, carbon black, carbon fiber, graphite, lignite, bituminous coal and waste materials. In this paper, ternary carbonate-samarium doped ceria (LNK-SDC) electrolyte has been synthesized via co-precipitation technique, while LiNi-CuZnFeO (LNCZFO) electrode has been prepared using solid state reaction method. Due to significant ionic conductivity of electrolyte LNK-SDC, it is used in DCFC. Three types of solid carbon (lignite, bituminous, sub-bituminous) are used as fuel to generate power. The X-ray diffraction confirmed the cubic crystalline structure of samarium doped ceria, whereas XRD pattern of LNCZFO showed its composite structure. The proximate and ultimate coal analysis showed that fuel (carbon) with higher carbon content and lower ash content was promising fuel for DCFC. The measured ionic conductivity of LNK-SDC is 0.0998 Scm(-1) and electronic conductivity of LNCZFO is 10.1 Scm(-1) at 700 degrees C, respectively. A maximum power density of 58 mWcm(-2) is obtained using sub bituminous fuel.
|
|
| 4. |
- Ali, Amjad, et al.
(författare)
-
Promising electrochemical study of titanate based anodes in direct carbon fuel cell using walnut and almond shells biochar fuel
- 2019
-
Ingår i: Journal of Power Sources. - : ELSEVIER. - 0378-7753 .- 1873-2755. ; 434
-
Tidskriftsartikel (refereegranskat)abstract
- The direct carbon fuel cell (DCFC) is an efficient device that converts the carbon fuel directly into electricity with 100% theoretical efficiency contrary to practical efficiency around 60%. In this paper four perovskite anode materials La0.4Sr0.6M0.09Ti0.91O3-delta (M = Ni, Fe, Co, Zn) have been prepared using sol-gel technique to measure the performance of the device using solid fuel. These materials have shown reasonable stability and conductivity at 700 degrees C. Further structural analysis of as-prepared anode material using XRD technique reveals a single cubic perovskite structure with average crystallite size roughly 47 nm. Walnut and almond shells biochar have also been examined as a fuel in DCFC at the temperature range 400-700 degrees C. In addition, Elemental analysis of walnut and almond shells has shown high carbon content and low nitrogen and sulfur contents in the obtained biochar. Subsequently, the superior stability of as-prepared anode materials is evident by thermogravimetric analysis in pure N-2 gas atmosphere. Conversely, the LSFT anode has shown the highest electronic conductivity of 7.53Scm(-1) at 700 degrees C. The obtained power density for LSFTO3-delta composite anode mixed in sub-bituminous coal, walnut and almond shells biochar is of 68, 55, 48 mWcm(-2) respectively. A significant improvement in performance of DCFC (78 mWcm(-2)) was achieved.
|
|
| 5. |
- Ullah, Kaleem, et al.
(författare)
-
Cerebral phaeohyphomycosis in liver transplant recipient : A case report
- 2022
-
Ingår i: Clinical Case Reports. - : Wiley. - 2050-0904. ; 10:12
-
Tidskriftsartikel (refereegranskat)abstract
- Cerebral phaeohyphomycosis is a fungal brain infection with a high fatality rate. It is caused by dematiaceous fungi and is increasingly recognized as a cause of serious illness in both immunocompetent and immunocompromised patients. We report cerebral phaeohyphomycosis in a liver transplant recipient. He was treated with multiple surgeries and antifungals and made a complete recovery. This report highlights that early and aggressive surgical intervention and extended antifungal coverage can have a positive outcome even in immunocompromised patients. The fungal infection in immunocompromised patients should be considered and treated aggressively.
|
|
| 6. |
- Irshad, Muneeb, et al.
(författare)
-
A Brief Description of High Temperature Solid Oxide Fuel Cell's Operation, Materials, Design, Fabrication Technologies and Performance
- 2016
-
Ingår i: Applied Sciences. - : MDPI AG. - 2076-3417. ; 6:3
-
Forskningsöversikt (refereegranskat)abstract
- Today's world needs highly efficient systems that can fulfill the growing demand for energy. One of the promising solutions is the fuel cell. Solid oxide fuel cell (SOFC) is considered by many developed countries as an alternative solution of energy in near future. A lot of efforts have been made during last decade to make it commercial by reducing its cost and increasing its durability. Different materials, designs and fabrication technologies have been developed and tested to make it more cost effective and stable. This article is focused on the advancements made in the field of high temperature SOFC. High temperature SOFC does not need any precious catalyst for its operation, unlike in other types of fuel cell. Different conventional and innovative materials have been discussed along with properties and effects on the performance of SOFC's components (electrolyte anode, cathode, interconnect and sealing materials). Advancements made in the field of cell and stack design are also explored along with hurdles coming in their fabrication and performance. This article also gives an overview of methods required for the fabrication of different components of SOFC. The flexibility of SOFC in terms fuel has also been discussed. Performance of the SOFC with varying combination of electrolyte, anode, cathode and fuel is also described in this article.
|
|
