| 1. |
- Bosse, H., et al.
(författare)
-
AdvManuNet : A networking project on metrology for advanced manufacturing
- 2020
-
Ingår i: Proceedings of the 20th International Conference of the European Society for Precision Engineering and Nanotechnology, EUSPEN 2020. - : euspen. - 9780995775176 ; , s. 357-358
-
Konferensbidrag (refereegranskat)abstract
- The networking project AdvManuNet has been started recently to accelerate the process of establishing an European Metrology Network (EMN) on Advanced Manufacturing. EMNs are intended by EURAMET, the association of metrology institutes in Europe, to provide a sustainable structure for ongoing stakeholder interaction in different thematic areas. Advanced manufacturing has been identified by the European Commission (EC) as one of six Key Enabling Technologies (KETs) with applications in multiple industries. Various EURAMET projects have partly addressed metrology needs for advanced manufacturing. However, a high-level coordination of the metrology community is currently absent and limits the impact of metrology developments on advanced manufacturing. AdvManuNet will address these limits by establishing a single hub for stakeholder consultation, a knowledge base on research results, and a strategic agenda for research and training to push forward advanced manufacturing and related KETs and strengthen Europe's position in advanced manufacturing via the EMN.
|
|
| 2. |
- Matus, M., et al.
(författare)
-
Key Comparison EURAMET.L-K1.2011 Measurement of gauge blocks by interferometry
- 2016
-
Ingår i: Metrologia. - 0026-1394 .- 1681-7575. ; 53:1A
-
Tidskriftsartikel (refereegranskat)abstract
- The key comparison EURAMET.L-K1.2011 on gauge blocks was carried out in the framework of a EURAMET project starting in 2012 and ending in 2015. It involved the participation of 24 National Metrology Institutes from Europe and Egypt, respectively. 38 gauge blocks of steel and ceramic with nominal central lengths between 0.5 mm and 500 mm were circulated. The comparison was conducted in two loops with two sets of artifacts. A statistical technique for linking the reference values was applied. As a consequence the reference value of one loop is influenced by the measurements of the other loop although they did not even see the artifacts of the others. This influence comes solely from three "linking laboratories" which measure both sets of artifacts. In total there were 44 results were not fully consistent with the reference values. This represents 10% of the full set of 420 results which is a considerable high number. At least 12 of them are clearly outliers where the participants have been informed by the pilot as soon as possible. The comparison results help to support the calibration and measurement capabilities (CMCs) of the laboratories involved in the CIPM MRA.
|
|
| 3. |
- Przyklenk, A., et al.
(författare)
-
AdvManuNet : Support for a European Metrology Network for advanced manufacturing
- 2021
-
Ingår i: Proceedings of the 21st International Conference of the European Society for Precision Engineering and Nanotechnology, EUSPEN 2021. - : euspen. - 9780995775190 ; , s. 321-322
-
Konferensbidrag (refereegranskat)abstract
- Advanced manufacturing has been identified as one of the key enabling technologies (KET) with applications in multiple industries. Advanced manufacturing requires new and enhanced metrology methods to assure the quality of manufacturing processes and resulting products. However, a high-level coordination of the metrology community in Europe is currently absent in this domain and limits the impact of metrology developments on advanced manufacturing. This gap aims to be closed through the establishment of a European Metrology Network (EMN) for advanced manufacturing. Here we report on the approach, first activities and the latest progress to establish a EMN on advanced manufacturing within EURAMET, the European Association of National Metrology Institutes (NMI). The objectives of this EMN are to set up a permanent stakeholder dialogue, to develop a Strategic Research Agenda (SRA) for metrology input needed for advanced manufacturing technologies, to create and maintain a knowledge sharing programme and to implement a web-based service desk for stakeholders involved in advanced manufacturing.
|
|
