| 1. |
- Krakhmalev, Pavel, 1973-, et al.
(författare)
-
Microstructure, solidification texture, and thermal stability of 316 L stainless steel manufactured by laser powder bed fusion
- 2018
-
Ingår i: Metals. - : MDPI AG. - 2075-4701. ; 8:8, s. 1-18
-
Tidskriftsartikel (refereegranskat)abstract
- This article overviews the scientific results of the microstructural features observed in 316 L stainless steel manufactured by the laser powder bed fusion (LPBF) method obtained by the authors, and discusses the results with respect to the recently published literature. Microscopic features of the LPBF microstructure, i.e., epitaxial nucleation, cellular structure, microsegregation, porosity, competitive colony growth, and solidification texture, were experimentally studied by scanning and transmission electron microscopy, diffraction methods, and atom probe tomography. The influence of laser power and laser scanning speed on the microstructure was discussed in the perspective of governing the microstructure by controlling the process parameters. It was shown that the three-dimensional (3D) zig-zag solidification texture observed in the LPBF 316 L was related to the laser scanning strategy. The thermal stability of the microstructure was investigated under isothermal annealing conditions. It was shown that the cells formed at solidification started to disappear at about 800 °C, and that this process leads to a substantial decrease in hardness. Colony boundaries, nevertheless, were quite stable, and no significant grain growth was observed after heat treatment at 1050 °C. The observed experimental results are discussed with respect to the fundamental knowledge of the solidification processes, and compared with the existing literature data.
|
|
| 2. |
|
|
| 3. |
- Åsberg, Mikael, et al.
(författare)
-
Influence of post treatment on microstructure, porosity and mechanical properties of additive manufactured H13 tool steel
- 2019
-
Ingår i: Materials Science & Engineering. - : Elsevier BV. - 0921-5093 .- 1873-4936. ; 742, s. 584-589
-
Tidskriftsartikel (refereegranskat)abstract
- Additive manufacturing (AM) is an attractive manufacturing technology in tooling applications. It provides unique opportunities to manufacture tools with complex shapes, containing inner channels for conformal cooling. In this investigation, H13, a widely used tool steel, was manufactured using a laser powder bed fusion method. Microstructure, tensile mechanical properties, hardness, and porosity of the AM H13 after stress relieve (SR), standard hardening and tempering (SR + HT), and hot isostatic pressing (SR + HIP + HT) were investigated. It was found that the microstructure of directly solidified colonies of prior austenite, which is typical for AM, disappeared after austenitizing at the hardening heat treatment. In specimens SR + HT and SR + HIP + HT, a microstructure similar to the conventional but finer was observed. Electron microscopy showed that SR and SR + HT specimens contained lack of fusion, and spherical gas porosity, which resulted in remarkable scatter in the observed elongation to break values. Application of HIP resulted in the highest strength values, higher than those observed for conventional H13 heat treated in the same way. The conclusion is that HIP promotes reduction of porosity and lack of fusion defects and can be efficiently used to improve the mechanical properties of AM H13 tool steel.
|
|
| 4. |
|
|
| 5. |
- Hentschel, Oliver, et al.
(författare)
-
Influence of the in-situ heat treatment during manufacturing on the microstructure and properties of DED-LB/M manufactured maraging tool steel
- 2023
-
Ingår i: Journal of Materials Processing Technology. - : Elsevier. - 0924-0136 .- 1873-4774. ; 315
-
Tidskriftsartikel (refereegranskat)abstract
- Due to high productivity, additive manufacturing (AM), and especially Directed Energy Deposition using laser and metallic powder (DED-LB/M) is attractive for manufacturing tools with integrated functionalities. This investigation was dedicated to DED-LB/M manufacturing of experimental maraging tool steel, characterization of the build microstructure with advanced electron microscopy and evaluation of hardness properties. High printability and low porosity of the final builds were observed, relative density was not lower than 99.5% for specimens manufactured with 600 W and 800 W, but microstructure and properties of the build had a gradient along the height. The characteristic hardness profile and microstructure, which were dependent on the manufacturing parameters, were observed. The top layers of manufactured maraging steel samples had a structure of martensite with precipitates presumably formed during solidification. The top layers were therefore softer to the depth of the austenitization isotherm. The higher hardness was measured in the inner regions which was a result of an in-situ heat treatment that the manufactured material was subjected to during layer-by-layer manufacturing. Thermal cycles during manufacturing resulted in precipitation hardening effect in the inner regions. Scanning and transmission electron microscopy confirmed the formation film-like and round particles in the as-build material, in top and inner regions. However, the quasicrystalline nano-sized R′-phase precipitates were observed only in the inner regions. The formation of the R′-phase precipitated during manufacturing as a result of the in-situ heat treatment was discussed as a reason for higher hardness (440 – 450 HV1) measured in the inner regions.
|
|
| 6. |
- Kazantseva, Natalia, et al.
(författare)
-
Twins in SLM Ti alloy
- 2017
-
Ingår i: Titan. - : Mezhgosudarstvennaya Assotsyatsiya Titan. - 2075-2903. ; :2, s. 8-15
-
Tidskriftsartikel (refereegranskat)
|
|
| 7. |
|
|
| 8. |
|
|
| 9. |
|
|
| 10. |
- Krakhmalev, Pavel, 1973-, et al.
(författare)
-
Influence of heat treatment under hot isostatic pressing (HIP) on microstructure of intermetallic-reinforced tool steel manufactured by laser powder bed fusion
- 2020
-
Ingår i: Materials Science & Engineering A: Structural Materials: Properties, Microstructure and Processing. - : Elsevier BV. - 0921-5093 .- 1873-4936. ; 772
-
Tidskriftsartikel (refereegranskat)abstract
- Microstructure and properties of as-built laser powder bed fusion (LPBF) steels differ from the conventional ones, and they may contain some porosity and lack of fusion. Therefore, post-treatments, including hot isostatic pressing (HIP), are used to density the material, and tailor the properties of the final product. Usually, HIP is performed as an operation separate from heat treatment. In the present investigation a new approach was used, in which the whole cycle of the heat treatment was carried out in HIP under pressure, and the influence of HIP on microstructure of an advanced stainless maraging tool steel manufactured by LPBF was investigated. For a comparison, a conventional steel grade of the same chemical composition, after a heat treatment at the same temperature-time conditions, was also characterized. The microstructure of the steel was investigated by means of advanced microscopy and atom probe tomography. The influence of the manufacturing route, heat treatment and HIP on microstructure, austenitic phase fraction and size distribution of precipitates was investigated, and the role of high pressure in stabilization of austenite in the microstructure was discussed. It was concluded that since HIP influences phase transformations, a fundamental understanding of the influence of HIP on microstructure is nececcary, and development of new post processing regimes guaranteeing the best performance of the material is required.
|
|
