| 11. |
- Ryttberg, Kristina, 1977, et al.
(författare)
-
Microstructural evolution during fracture induced by high strain rate deformation of 100Cr6 steel
- 2009
-
Ingår i: Journal of Materials Processing Technology. - : Elsevier BV. - 0924-0136. ; 209:7, s. 3325-3334
-
Tidskriftsartikel (refereegranskat)abstract
- This paper investigates the influence on parting-off mechanisms of a significantly higher impact velocity compared to commercial methods. A specially developed method, allowing for parting-off velocities ranging from 38 to 285 m/s has been applied to 100Cr6 steel bars. Two different heat treatments; spheroidise annealing (SA) and quench and tempering (QT) were employed to produce two different microstructures of a hardness of 255 and 310HV, respectively. It appears that the failure mechanisms active in the current process are virtually identical to failure occurring during high-velocity parting-off using commercially available machines, which displays shear fracture and adiabatic shear banding. It was also concluded that the estimated energy consumed during parting-off is not dependent on microstructure. Prior to parting-off, impact results in shear localisation, which is somewhat increased with increased impact speed. Furthermore, shear strains at fracture also increaseswith impact speed, from a value of about 2.2 at the lowest impact velocity to almost 3.5 at an impact velocity of 285 m/s. The heavy deformation causes a grain refinement. Right below the fracture surface three subzones can be found in the microstructure; a white etching band (WEB) (only present on some locations), equiaxed grains and then elongated subgrains. The grain size within these zones varies between 50 and 150 nm. The findings of elongated subgrains of a mutual orientation, adjacent subgrains having {110} type of planes in parallel, support the theory of formation of white etching bands being a mechanically rate controlled process.
|
|
| 12. |
- Ryttberg, Kristina, 1977, et al.
(författare)
-
Microstructure and texture development during ring rolling of 100Cr6
- 2008
-
Ingår i: Ceramic Transactions. - 1042-1122. - 9781574982961 ; 200, s. 301-309
-
Konferensbidrag (refereegranskat)abstract
- Pre-turned 100Cr6 steel rings with spheroidised annealed microstructure have been cold ring rolled to two levels: expanding the outer diameter by 10 and 20%. The final microstructure was shown to be varying throughout the cross-section of the ring, where the largest deformation was found close to the surface of the inner diameter. This was reflected in the hardness profile showing the highest hardness values close to the inner surface. Scanning electron microscopy showed that the microstructure below the surface of the outer diameter consisted of a greatly refined ferrite. Close to the surface of the inner diameter the structure was even more refined. Electron back scatter diffraction together with X-ray diffractometry showed that cold ring rolling changed the existing texture of the ring blanks, where {110}-planes were parallel to the axial direction of the rings, towards {110}-planes becoming parallel to the rolling direction. This resulted in a weak {110}-texture. Close to the surface of the outer diameter the greatly refined ferrite had decomposed into a more random orientation distribution.
|
|
| 13. |
|
|
| 14. |
- Ryttberg, Kristina, 1977, et al.
(författare)
-
The effect of cold ring rolling on the evolution of microstructure and texture in 100Cr6 steel
- 2010
-
Ingår i: Materials Science & Engineering A: Structural Materials: Properties, Microstructure and Processing. - : Elsevier BV. - 0921-5093. ; 527:9, s. 2431-2436
-
Tidskriftsartikel (refereegranskat)abstract
- This paper concerns the development of microstructure and texture during cold ring rolling of 100Cr6 steel rings with starting rectangular cross-sections. By interrupting the rolling process at pre-defined intervals expansion ratios ranging from 1.05 to 1.5 were achieved resulting in varying degrees of deformation of the rings. Results for rings with a simple rectangular cross-section were compared with results for a cold rolled ring with a more complex cross-section. By combining results from optical and scanning electron microscopy with hardness measurements the two different ring shapes were shown to display similar material flow during cold ring rolling. The deformation was most severe near the inner diameterof the rings decreasing towards the area of the outer diameter. By employing electron back scatter diffraction (EBSD) the ring rolling process was shown to change the {111}-fibre texture of the ring blanks to a {110} texture. This implies a mixture of both shear and compressive deformation during rolling.
|
|
