| 1. |
|
|
| 2. |
- Carpman, Nicole
(författare)
-
Resource characterization and variability studies for marine current power
- 2017
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Producing electricity from marine renewable resources is a research area that develops continuously. The field of tidal energy is on the edge to progress from the prototype stage to the commercial stage. However, tidal resource characterization, and the effect of tidal turbines on the flow, is still an ongoing research area in which this thesis aims to contribute.In this thesis, measurements of flow velocities have been performed at three kinds of sites. Firstly, a tidal site has been investigated for its resource potential in a fjord in Norway. Measurements have been performed with an acoustic Doppler current profiler to map the spatial and temporal characteristics of the flow. Results show that currents are in the order of 2 m/s in the center of the channel. Furthermore, the flow is highly bi-directional between ebb and flood flows. The site thus has potential for in-stream energy conversion. Secondly, a river site serves as an experimental site for a marine current energy converter that has been designed at Uppsala University and deployed in Dalälven, Söderfors. The flow rate at the site is regulated by an upstream hydro power plant, making the site suitable for experiments on the performance of the vertical axis turbine in a natural environment. The turbine was run in steady discharge flows and measurements were performed to characterize the extent of the wake. Lastly, at an ocean current site, the effect that transiting ferries may have on submerged devices was investigated. Measurements were conducted with two sonar systems to obtain an underwater view of the wake caused by a propeller and a water jet thruster respectively.Furthermore, the variability of the intermittent renewable sources wind, solar, wave and tidal energy was investigated for the Nordic countries. All of the sources have distinctly different variability features, which is advantageous when combining power generated from them and introducing it on the electricity grid. Tidal variability is mainly due to four aspects: the tidal regime, the tidal cycle, local bathymetry causing turbulence, asymmetries etc. and weather effects. Models of power output from the four sources was set up and combined in different energy mixes for a “highly renewable” and a “fully renewable” scenario. By separating the resulting power time series into different frequency bands (long-, mid-, mid/short-, and short-term components) it was possible to minimize the variability on different time scales. It was concluded that a wise combination of intermittent renewable sources may lower the variability on short and long time scales, but increase the variability on mid and mid/short time scales.The tidal power variability in Norway was then investigated separately. The predictability of tidal currents has great advantages when planning electricity availability from tidal farms. However, the continuously varying tide from maximum power output to minimum output several times per day increases the demand for backup power or storage. The phase shift between tidal sites introduces a smoothing effect on hourly basis but the tidal cycle, with spring and neap tide simultaneously in large areas, will inevitably affect the power availability.
|
|
| 3. |
- Chatzigiannakou, Maria Angiliki, et al.
(författare)
-
Offshore Deployments of Wave Energy Converters by Seabased Industry AB
- 2017
-
Ingår i: Journal of Marine Science and Engineering. - : MDPI AG. - 2077-1312. ; 5:2
-
Tidskriftsartikel (refereegranskat)abstract
- Since 2008, Seabased Industry AB (SIAB) has manufactured and deployed several units of wave energy converters (WECs) of different design. The WECs are linear generators with point absorber buoy systems that are placed on the seabed, mounted on a gravitation concrete foundation. These deployments have taken place in different areas, using different deployment vessels. Offshore deployments of WECs and underwater substations have so far been complicated procedures, that were both expensive and time-consuming. The focus of this paper is to discuss these deployments in terms of economy and time efficiency, as well as safety. Because seven vessels have been used to facilitate the deployments, an evaluation on the above basis is carried out for them. The main conclusions and certain solutions are presented for the various problems encountered during these deployments and the vessel choice is discussed. It is found that the offshore deployment process can be optimized in terms of cost, time efficiency and safety with a careful vessel choice, use of the latest available technologies and detailed planning and organizing.
|
|
| 4. |
- Chen, WenChuang, et al.
(författare)
-
Numerical modelling of a point-absorbing wave energy converter in irregular and extreme waves
- 2017
-
Ingår i: Applied Ocean Research. - : Elsevier BV. - 0141-1187 .- 1879-1549. ; 63, s. 90-105
-
Tidskriftsartikel (refereegranskat)abstract
- Based on the Navier-Stokes (RANS) equations, a three-dimensional (3-D) mathematical model for the hydrodynamics and structural dynamics of a floating point-absorbing wave energy converter (WEC) with a stroke control system in irregular and extreme waves is presented. The model is validated by a comparison of the numerical results with the wave tank experiment results of other researchers. The validated model is then utilized to examine the effect of wave height on structure displacements and connection rope tension. In the examined cases, the differences in WEC’s performance exhibited by an inviscid fluid and a viscous fluid can be neglected. Our results also reveal that the differences in behavior predicted by boundary element method (BEM) and the RANS-based method can be significant and vary considerably, depending on wave height.
|
|
| 5. |
|
|
| 6. |
- Eklund, Petter, 1989-, et al.
(författare)
-
Magnetic End LeakageFlux in a Spoke Type Rotor Permanent Magnet SynchronousGenerator
- 2017
-
Konferensbidrag (övrigt vetenskapligt/konstnärligt)abstract
- The spoke type rotor can be used to obtain magnetic flux concentration in permanent magnet machines. This allows the air gap magnetic flux density to exceed the remanent flux density of the permanent magnets but gives problems with leakage fluxes in the magnetic circuit. The end leakage flux of one spoke type permanent magnet rotor design is studied through measurements and finite element simulations. The measurements are performed in the end regions of a 12 kW prototype generator for a vertical axis wind turbine. The simulations are made using three dimensional finite elements to calculate the magnetic field distribution in the end regions of the machine. Also two dimensional finite element simulations are performed and the impact of the two dimensional approximation is studied. It is found that the magnetic leakage flux in the end regions of the machine is equal to about 20 % of the flux in the permanent magnets. The overestimation of the performance by the two dimensional approximation is quantified and a curve-fitted expression for its behavior is suggested.
|
|
| 7. |
- Elamalayil Soman, Deepak, et al.
(författare)
-
Cross-Regulation Assessment of DIDO Buck-Boost Converter for Renewable Energy Application
- 2017
-
Ingår i: Energies. - : MDPI AG. - 1996-1073. ; 10:7
-
Tidskriftsartikel (refereegranskat)abstract
- When medium- or high-voltage power conversion is preferred for renewable energy sources, multilevel power converters have received much of the interest in this area as methods for enhancing the conversion efficiency and cost effectiveness. In such cases, multilevel, multi-input multi-output (MIMO) configurations of DC-DC converters come to the scenario for integrating several sources together, especially considering the stringent regulatory needs and the requirement of multistage power conversion systems. Considering the above facts, a three-level dual input dual output (DIDO) buck-boost converter, as the simplest form of MIMO converter, is proposed in this paper for DC-link voltage regulation. The capability of this converter for cross regulating the DC-link voltage is analyzed in detail to support a three-level neutral point clamped inverter-based grid connection in the future. The cross-regulation capability is examined under a new type of pulse delay control (PDC) strategy and later compared with a three-level boost converter (TLBC). Compared to conventional boost converters, the high-voltage three-level buck boost converter (TLBBC) with PDC exhibits a wide controllability range and cross regulation capability. These enhanced features are extremely important for better regulating variable output renewable energy sources such as solar, wind, wave, marine current, etc. The simulation and experimental results are provided to validate the claim.
|
|
| 8. |
- Elamalayil Soman, Deepak, 1984-
(författare)
-
Multilevel Power Converters with Smart Control for Wave Energy Conversion
- 2017
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- The main focus of this thesis is on the power electronic converter system challenges associated with the grid integration of variable-renewable-energy (VRE) sources like wave, marine current, tidal, wind, solar etc. Wave energy conversion with grid integration is used as the key reference, considering its high energy potential to support the future clean energy requirements and due the availability of a test facility at Uppsala University. The emphasis is on the DC-link power conditioning and grid coupling of direct driven wave energy converters (DDWECs). The DDWEC reflects the random nature of its input energy to its output voltage wave shape. Thereby, it demands for intelligent power conversion techniques to facilitate the grid connection.One option is to improve and adapt an already existing, simple and reliable multilevel power converter technology, using smart control strategies. The proposed WECs to grid interconnection system consists of uncontrolled three-phase rectifiers, three-level boost converter(TLBC) or three-level buck-boost converter (TLBBC) and a three-level neutral point clamped (TLNPC) inverter. A new method for pulse delay control for the active balancing of DC-link capacitor voltages by using TLBC/TLBBC is presented. Duty-ratio and pulse delay control methods are combined for obtaining better voltage regulation at the DC-link and for achieving higher controllability range. The classic voltage balancing problem of the NPC inverter input, is solved efficiently using the above technique. A synchronous current compensator is used for the NPC inverter based grid coupling. Various results from both simulation and hardware testing show that the required power conditioning and power flow control can be obtained from the proposed multilevel multistage converter system.The entire control strategies are implemented in Xilinx Virtex 5 FPGA, inside National Instruments’ CompactRIO system using LabVIEW. A contour based dead-time harmonic analysis method for TLNPC and the possibilities of having various interconnection strategies of WEC-rectifier units to complement the power converter efforts for stabilizing the DC-link, are also presented. An advanced future AC2AC direct power converter system based on Modular multilevel converter (MMC) structure developed at Siemens AG is presented briefly to demonstrate the future trends in this area.
|
|
| 9. |
- Engström, Jens, et al.
(författare)
-
Buoy geometry and its influence on survivability for apoint absorbing wave energy converter : Scaleexperiment and CFD simulations
- 2017
-
Konferensbidrag (refereegranskat)abstract
- For wave energy to be an economically viable energysource, the technology has to withstand power levelsduring storms that can be close to 50 times higher thanduring normal operating conditions, and withstandmany years of wear. The impact of high wave loads isstudied not only within the field of wave energy, buthas long been a subject of study for ships, platformsand other offshore structures.To model the force on the device under extreme and/orovertopping waves is a difficult task. Experiments areexpensive and difficult to implement, and numerical meth-ods are either very computationally demanding CFD-methods, or less accurate approximative methods. Inaddition, the performance and experienced forces during extreme waves are model dependent, and differentoffshore structures must be studied independently.Here, a 1:20 scale model of the Uppsala Universitypoint-absorber type wave energy converter (WEC) has been tested in extreme wave conditions at the COASTLaboratory Ocean Basin at Plymouth University. The WEC consists of a linear generator connected to a buoyat the sea surface, and performance of two differentbuoys is studied: a cylinder and cylinder with moon-pool. Two types of wave sets have been used: focusedwaves embedded into regular waves, and irregular waves. The focus of this paperis on comparing the performance of the two buoys, and on analysing the experimental data using a numerical model. A fully non-linear computational fluid dynamics(CFD) model based on OpenFOAM is presented and validated.
|
|
| 10. |
- Forslund, Johan, 1985-, et al.
(författare)
-
Power And Energy Needed For Starting A Vertical Axis Marine Current Turbine
- 2017
-
Konferensbidrag (refereegranskat)abstract
- A marine current power station has been deployed in Söderfors, Sweden. It comprises a five bladed fixed pitch vertical axis H-rotor turbine directly connected to a permanent magnet synchronous generator. The turbine is rated for 1.3 m/s, but at lower water speeds the turbine is generally not self starting. This paper investigates the energy and power needed to at low speeds start the turbine electrically with a BrushLess DC (BLDC) motor until he turbines gives a net positive torque to the generator. A range of startup BLDC powers have been investigated. It is shown that for three water speeds (0.98 m/s, 1.04 m/s and 1.16 m/s) the energy needed for start up is equivalent to less than 1.2 s of power production at maximum power capture of the turbine. The startup time is mostly dependent on BLDC power setting, not on water speed. A BLDC power of 1/7th of rated power of the machine is enough to start the machine within 2 seconds. The results suggest that a higher BLDC power than that will not significantly reduce the startup time nor reduce the energy needed (increase the efficiency of the startup process). The water speed has the highest impact on the time it takes to recover the energy needed for startup once the BLDC power is well above the losses in the system.
|
|
