| 1. |
- Adcox, K, et al.
(författare)
-
PHENIX detector overview
- 2003
-
Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - 0167-5087. ; 499:2-3, s. 469-479
-
Tidskriftsartikel (refereegranskat)abstract
- The PHENIX detector is designed to perform a broad study of A-A, p-A, and p-p collisions to investigate nuclear matter under extreme conditions. A wide variety of probes, sensitive to all timescales, are used to study systematic variations with species and energy as well as to measure the spin structure of the nucleon. Designing for the needs of the heavy-ion and polarized-proton programs has produced a detector with unparalleled capabilities. PHENIX measures electron and muon pairs, photons, and hadrons with excellent energy and momentum resolution. The detector consists of a large number of subsystems that are discussed in other papers in this volume. The overall design parameters of the detector are presented. (C) 2002 Elsevier Science B.V. All rights reserved.
|
|
| 2. |
- Adler, SS, et al.
(författare)
-
PHENIX on-line systems
- 2003
-
Ingår i: Nuclear Instruments & Methods in Physics Research. Section A: Accelerators, Spectrometers, Detectors, and Associated Equipment. - 0167-5087. ; 499:2-3, s. 560-592
-
Tidskriftsartikel (refereegranskat)abstract
- The PHENIX On-Line system takes signals from the Front End Modules (FEM) on each detector subsystem for the purpose of generating events for physics analysis. Processing of event data begins when the Data Collection Modules (DCM) receive data via fiber-optic links from the FEMs. The DCMs format and zero suppress the data and generate data packets. These packets go to the Event Builders (EvB) that assemble the events in final form. The Level-1 trigger (LVL1) generates a decision for each beam crossing and eliminates uninteresting events. The FEMs carry out all detector processing of the data so that it is delivered to the DCMs using a standard format. The FEMs also provide buffering for LVL1 trigger processing and DCM data collection. This is carried out using an architecture that is pipelined and deadtimeless. All of this is controlled by the Master Timing System (MTS) that distributes the RHIC clocks. A Level-2 trigger (LVL2) gives additional discrimination. A description of the components and operation of the PHENIX On-Line system is given and the solution to a number of electronic infrastructure problems are discussed. (C) 2002 Elsevier Science B.V. All rights reserved.
|
|
| 3. |
|
|
| 4. |
- Zhang, J. G., et al.
(författare)
-
Microstructure and mechanical properties of spray formed ultrahigh-carbon steels
- 2004
-
Ingår i: Materials Science & Engineering. - : Elsevier BV. - 0921-5093 .- 1873-4936. ; 383:1, s. 45-49
-
Tidskriftsartikel (refereegranskat)abstract
- The microstructure and mechanical properties of the spray formed 1.25C-3.0Si-1.5Cr ultrahigh-carbon steel (UHCS) were described. The 1.25C-3.0Si-1.5Cr UHCS was processed by spray forming to break up carbide networks. The fine pearlites with average interlamellar spacing of 0.20 mum was observed in the as-sprayed microstructure. The ultimate tensile strength and the pearlite spacing can be related by the Hall-Petch equation. The as-sprayed 1.25C-3.0Si-1.5Cr UHCS consisting of fine lamellar pearlites has been shown to exhibit superplastic behavior at elevated temperature. The dramatic change of microstructure from fine lamellar pearlites to equiaxed grains stabilized by spheroidized particles during superplastic deformation has been observed. The estimation on the basis of thermodynamics shows that the content of chromium of 1.54 wt.% is needed to inhibit graphite formation in the l.25C-3.OSi-1.5Cr UHCS.
|
|
| 5. |
|
|
| 6. |
|
|
| 7. |
|
|
| 8. |
|
|
| 9. |
- Borlado, CR, et al.
(författare)
-
Neutron strain scanning on bimetallic tubes
- 2000
-
Ingår i: MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING. - : ELSEVIER SCIENCE SA. - 0921-5093. ; 288:2, s. 288-292
-
Tidskriftsartikel (refereegranskat)abstract
- Neutron diffraction measurements have been carried out on the REST diffractometer (Studsvik) on curved components fabricated by cold working bimetallic tubes. The tubes consist of two layers (an outer one of austenitic steel and an inner one of ferritic s
|
|
| 10. |
|
|
