| 1. |
- Bladh, Henrik, et al.
(författare)
-
Influence of Soot Particle Aggregation on Time-Resolved Laser-Induced Incandescence Signals
- 2011
-
Ingår i: Applied Physics B. - : Springer Science and Business Media LLC. - 0946-2171 .- 1432-0649. ; 104:2, s. 331-341
-
Tidskriftsartikel (refereegranskat)abstract
- Laser-induced incandescence (LII) is a versatile technique for quantitative soot measurements in flames and exhausts. When used for particle sizing, the time-resolved signals are analysed as these will show a decay rate dependent on the soot particle size. Such an analysis has traditionally been based on the assumption of isolated primary particles. However, soot particles in flames and exhausts are usually aggregated, which implies loss of surface area, less heat conduction and hence errors in estimated particle sizes. In this work we present an experimental investigation aiming to quantify this effect. A soot generator, based on a propane diffusion flame, was used to produce a stable soot stream and the soot was characterised by transmission electron microscopy (TEM), a scanning mobility particle sizer (SMPS) and an aerosol particle mass analyzer coupled in series after a differential mobility analyzer (DMA-APM). Despite nearly identical primary particle size distributions for three selected operating conditions, LII measurements resulted in signal decays with significant differences in decay rate. However, the three cases were found to have quite different levels of aggregation as shown both in TEM images and mobility size distributions, and the results agree qualitatively with the expected effect of diminished heat conduction from aggregated particles resulting in longer LII signal decays. In an attempt to explain the differences quantitatively, the LII signal dependence on aggregation was modelled using a heat and mass transfer model for LII given the primary particle and aggregate size distribution data as input. Quantitative agreement was not reached and reasons for this discrepancy are discussed.
|
|
| 2. |
- Dutcher, Dabrina D., et al.
(författare)
-
Emissions from soy biodiesel blends: A single particle perspective
- 2011
-
Ingår i: Atmospheric Environment. - : Elsevier BV. - 1352-2310. ; 45:20, s. 3406-3413
-
Tidskriftsartikel (refereegranskat)abstract
- Biodiesel has recently reemerged as a common fuel. However, emissions from biodiesel combustion have been studied in much less detail than those from traditional petroleum-based diesel. In this experiment, emissions from the combustion of different fuel blends (BOO, B02, B20, B99, where the number after B indicates the percentage, by volume, of biodiesel in the fuel) in a VW TDi engine were analyzed by aerosol time-of-flight mass spectrometers (ATOFMS) for single-particle composition and vacuum aerodynamic size. The ATOFMS results show that the PAH molecular weight distribution is not significantly affected by the fuel composition, and that sulfates are reduced by increased biodiesel content. Octanedioic acid (a carbonyl species) is increased with increased biodiesel concentration. Clustering results from the single-particle spectra show that the particles fall in five main types by chemical composition. The aerodynamic size distribution of these individual clusters was also determined. These results also show that methods used to identify diesel particle emissions for source apportionment are not applicable when significant concentrations of biodiesel are used in fuels. (C) 2011 Elsevier Ltd. All rights reserved.
|
|
| 3. |
- Eriksson, Axel, et al.
(författare)
-
Particulate PAH Emissions from Residential Biomass Combustion : Time-Resolved Analysis with Aerosol Mass Spectrometry
- 2014
-
Ingår i: Environmental Science and Technology. - : American Chemical Society (ACS). - 0013-936X .- 1520-5851. ; 48:12, s. 7143-7150
-
Tidskriftsartikel (refereegranskat)abstract
- Time-resolved emissions of particulate polycyclic aromatic hydrocarbons (PAHs) and total organic particulate matter (OA) from a wood log stove and an adjusted pellet stove were investigated with high-resolution time-of-flight aerosol mass spectrometry (AMS). The highest OA emissions were found during the addition of log wood on glowing embers, that is, slow burning pyrolysis conditions. These emissions contained about 1% PAHs (of OA). The highest PAH emissions were found during fast burning under hot air starved combustion conditions, in both stoves. In the latter case, PAHs contributed up to 40% of OA, likely due to thermal degradation of other condensable species. The distribution of PAHs was also shifted toward larger molecules in these emissions. AMS signals attributed to PAHs were found at molecular weights up to 600 Da. The vacuum aerodynamic size distribution was found to be bimodal with a smaller mode (Dva ~ 200 nm) dominating under hot air starved combustion and a larger sized mode dominating under slow burning pyrolysis (Dva ~ 600 nm). Simultaneous reduction of PAHs, OA and total particulate matter from residential biomass combustion may prove to be a challenge for environmental legislation efforts as these classes of emissions are elevated at different combustion conditions.
|
|
| 4. |
- Hagerman, Inger, et al.
(författare)
-
Effects on heart rate variability by artificially generated indoor nano-sized particles in a chamber study
- 2014
-
Ingår i: Atmospheric Environment. - : Elsevier BV. - 1352-2310. ; 88, s. 165-171
-
Tidskriftsartikel (refereegranskat)abstract
- Background: Airborne particles are associated with increased morbidity and mortality due to respiratory and cardiovascular diseases in polluted areas. There is a growing interest in nano-sized particles with diameter < 100 nm and their potential health effects. Heart rate variability (HRV) is a noninvasive method for cardiovascular risk prediction in high prevalent groups. Aim of study: The aim was to evaluate the impact of nano-sized indoor air particles on HRV for healthy and adult females. Methods: All exposures were performed as controlled chamber experiments with particle exposure from burning candles, terpene + ozone reactions or filtered air in a double-blind cross over design. Twenty-two healthy females were investigated during 10 min periods at different exposures and the reactivity in high frequency (HF) spectral band of HRV were computed. Results: Heart rate was unchanged from baseline values in all groups during all experimental settings. HF power of HRV tended to increase during exposure to particles from burning candle while particles from terpene + ozone reactions tended to decrease HF power. Conclusions: Exposure to nano-sized particles of burning candles or terpene + ozone reactions results in different patterns of heart rate variability, with signs of altered autonomic cardiovascular control. Practical implications: This study indicates that the HRV method may be used for information on physiological responses of exposure to different nano-sized particles and contribute to the understanding of mechanisms behind health effects of particle exposures. (C) 2014 The Authors. Published by Elsevier Ltd.
|
|
| 5. |
- Hedmer, Maria, et al.
(författare)
-
Exposure and Emission Measurements During Production, Purification, and Functionalization of Arc-Discharge-Produced Multi-walled Carbon Nanotubes.
- 2014
-
Ingår i: Annals of Occupational Hygiene. - : Oxford University Press (OUP). - 1475-3162. ; 58:3, s. 355-379
-
Tidskriftsartikel (refereegranskat)abstract
- Background: The production and use of carbon nanotubes (CNTs) is rapidly growing. With increased production, there is potential that the number of occupational exposed workers will rapidly increase. Toxicological studies on rats have shown effects in the lungs, e.g. inflammation, granuloma formation, and fibrosis after repeated inhalation exposure to some forms of multi-walled CNTs (MWCNTs). Still, when it comes to health effects, it is unknown which dose metric is most relevant. Limited exposure data for CNTs exist today and no legally enforced occupational exposure limits are yet established. The aim of this work was to quantify the occupational exposures and emissions during arc discharge production, purification, and functionalization of MWCNTs. The CNT material handled typically had a mean length <5 μm. Since most of the collected airborne CNTs did not fulfil the World Health Organization fibre dimensions (79% of the counted CNT-containing particles) and since no microscopy-based method for counting of CNTs exists, we decided to count all particle that contained CNTs. To investigate correlations between the used exposure metrics, Pearson correlation coefficient was used.
|
|
| 6. |
- Isaxon, Christina, et al.
(författare)
-
A Novel System for Source Characterization and Controlled Human Exposure to Nanoparticle Aggregates Generated During Gas–Metal Arc Welding
- 2013
-
Ingår i: Aerosol Science and Technology. - : Informa UK Limited. - 1521-7388 .- 0278-6826. ; 47:1, s. 52-59
-
Tidskriftsartikel (refereegranskat)abstract
- Abstract in Undetermined The aim of this study was to achieve a method to perform detailed characterization and human exposure studies of nanosized and nanostructured aerosol particles. The source chosen was mild steel, active gas, arc welding fume. The setup consisted of a generation chamber, where welding can be performed, connected to an airtight stainless steel 22 m(3) exposure chamber. Instrumentation, consisting of a tapered element oscillating microbalance, a scanning mobility particle sizer, and a sampler for electron microscopy and particle-induced X-ray emission analysis was connected to the stainless steel chamber. The feasibility of the system for human exposure studies was evaluated by exposing 31 human volunteers, in groups of three, to a test aerosol containing 1 mg/m(3) welding fumes and to conditioned, filtered air. The results show that an aerosol that accurately represents dilute welding fume exposures that occur in workplaces can be produced in a controlled manner, and that the experimental setup can be used for 6 h, double-blind, exposures of human subjects. Particle mass concentration levels could be varied from <5 mu g/m(3) to more than 1000 mu g/m(3). Fumes from metal active gas welding showed a unimodal size distribution with a mean mobility diameter of 160 nm, transmission electron microscopy showed aggregates with a clearly nanosized structure.
|
|
| 7. |
- Isaxon, Christina, et al.
(författare)
-
Realistic indoor nano-aerosols for a human exposure facility
- 2013
-
Ingår i: Journal of Aerosol Science. - : Elsevier BV. - 0021-8502. ; 60, s. 55-66
-
Tidskriftsartikel (refereegranskat)abstract
- The aim of this study was to achieve realistic levels of two different types of aerosols commonly abundant in indoor environments in an experimental chamber intended for human exposure studies and aerosol characterization. The aerosols chosen were particles from candle lights (in particle number dominated by inorganic water soluble particles) and from ozone-terpene reactions (organic particles). The aerosol generation and characterization system consisted of a controlled air tight stainless steel 22 m(3) chamber, to which the generation set-ups were connected. No air could enter or leave the chamber except through a conditioning system by which temperature, relative humidity and air exchange rate could be controlled. Candle smoke aerosol was generated from ten candles burning in a 1.33 m(3) glass and stainless steel chamber. The aerosol was diluted by clean air from the conditioning system before entering the chamber. Terpene vapor was generated by passing pure nitrogen through a glass bottle containing limonene oil. Ozone was generated by a spark discharge using pure O-2, and was added to the ventilation air flow downstream the inlet for terpene vapors and upstream the inlet to the chamber. Both aerosols were characterized with respect to number and mass concentrations, size distribution and chemical composition. Particle number concentration in the size range 10-650 nm could be varied from <10 cm(-3) to more than 900,000 cm(-3) (for candle smoke) or to more than 30,000 cm(-3) (for particles formed in a 160 ppb terpene/40 ppb ozone mixture). Furthermore, the set-ups were evaluated by, for each source, repeating the generation at six three-hour long events. For both aerosols repeatable generations at pre-determined concentration levels, that were stable over time, could be achieved. The results show that realistic concentrations of aerosols from real-world environments could be reproduced in a well-controlled manner and that this set-up could be used both for aerosol characterization and for human exposures. (C) 2013 Elsevier Ltd. All rights reserved.
|
|
| 8. |
- Lutic, Doina, et al.
(författare)
-
Detection of Soot Using a Resistivity Sensor Device Employing Thermophoretic Particle Deposition
- 2010
-
Ingår i: Journal of Sensors. - : Hindawi. - 1687-725X .- 1687-7268. ; 2010:421072
-
Tidskriftsartikel (refereegranskat)abstract
- Results are reported for thermophoretic deposition of soot particles on resistivity sensors as a monitoring technique for diesel exhaust particles with the potential of improved detection limit and sensitivity. Soot with similar characteristics as from diesel exhausts was generated by a propane flame and diluted in stages. The soot in a gas flow at 240–270C∘ was collected on an interdigitated electrode structure held at a considerably lower temperature, 105–125C∘. The time delay for reaching measurable resistance values, the subsequent rate, and magnitude of resistance decrease were a function of the distance between the fingers in the electrodes and the degree of dilution of the soot containing flow. Soot deposition and subsequent removal by heating the sensor support was also performed in a real diesel exhaust. Good similarities between the behavior in our laboratory system and the real diesel exhaust were noticed.
|
|
| 9. |
- Malik, Azhar, et al.
(författare)
-
A Potential Soot Mass Determination Method from Resistivity Measurement of Thermophoretically Deposited Soot
- 2011
-
Ingår i: AEROSOL SCIENCE AND TECHNOLOGY. - : Taylor and Francis. - 0278-6826 .- 1521-7388. ; 45:2, s. 284-294
-
Tidskriftsartikel (refereegranskat)abstract
- Miniaturized detection systems for nanometer-sized airborne particles are in demand, for example in applications for onboard diagnostics downstream particulate filters in modern diesel engines. A soot sensor based on resistivity measurements was developed and characterized. This involved generation of soot particles using a quenched co-flow diffusion flame; depositing the particles onto a sensor substrate using thermophoresis and particle detection using a finger electrode structure, patterned on thermally oxidized silicon substrate. The generated soot particles were characterized using techniques including Scanning Mobility Particle Sizer for mobility size distributions, Differential Mobility Analyzer-Aerosol Particle Mass analyzer for the mass-mobility relationship, and Transmission Electron Microscopy for morphology. The generated particles were similar to particles from diesel engines in concentration, mobility size distribution, and mass fractal dimension. The primary particle size, effective density and organic mass fraction were slightly lower than values reported for diesel engines. The response measured with the sensors was largely dependent on particle mass concentration, but increased with increasing soot aggregate mobility size. Detection down to cumulative mass as small as 20-30 mu g has been demonstrated. The detection limit can be improved by using a more sensitive resistance meter, modified deposition cell, larger flow rates of soot aerosol and modifying the sensor surface.
|
|
| 10. |
- Malik, Azhar, et al.
(författare)
-
Methodology for Sampling and Characterizing Internally Mixed Soot-Tar Particles Suspended in the Product Gas from Biomass Gasification Processes
- 2011
-
Ingår i: Energy & Fuels. - : American Chemical Society (ACS). - 0887-0624 .- 1520-5029. ; 25:4, s. 1751-1758
-
Tidskriftsartikel (refereegranskat)abstract
- When biomass is used to produce fuels and green products by thermochemical conversion, the ability to handle or remove the fine particle phase in the product gas is crucial. The product gas from biomass gasification contains relatively volatile organic compounds (“tar”) condensed on nonvolatile cores of, for example, aggregated soot particles and char. The problems are, for example, that particles will poison catalysts used for upgrading of the gas and loss of thermal energy occurs when carbonaceous particles are being formed. The aim of the work is to design and use novel methodologies to characterize the particles in the product gas stream. A methodology has been developed to sample and characterize fine particles by a sampling probe connected to either a denuder or a packed bed device. The system was designed to avoid condensation of organic compounds when diluting the sample and decreasing the temperature. A flame soot generator connected to a condensation−evaporation unit was used to produce internally mixed model particles, i.e., particles consisting of a core of soot with an outer layer of condensed volatile compounds. A scanning mobility particle sizer (SMPS) and a differential mobility analyzer followed by an aerosol particle mass analyzer (APM) were used to characterize the particles. Because of the agglomerated structure of soot, the SMPS system was not adequate to fully characterize the mass of volatiles condensed onto the soot core, and therefore the DMA-heater-APM technique was used to determine the mass fraction of the condensed phase on the soot particles. The two different configurations were studied, and the sampling system was shown to work at a high load of organic mass. In both cases, the organic removal efficiency was >99.5%. Minor condensation of organics on the sampled soot was found for the denuder but not the packed bed. On the other hand, the particle losses were substantially higher for the packed bed compared to the denuder. The results showed that the tested sampling methodology can be used to get sufficient characterization of particles in the product gas and to evaluate the performance of biomass product gas cleaning systems at high temperature.
|
|
