| 1. |
- Loarer, T., et al.
(författare)
-
Gas balance and fuel retention in fusion devices
- 2007
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 0029-5515 .- 1741-4326. ; 47:9, s. 1112-1120
-
Tidskriftsartikel (refereegranskat)abstract
- The evaluation of hydrogenic retention in present tokamaks is of crucial importance to estimate the expected tritium (T) vessel inventory in ITER, limited from safety considerations to 350 g. In the framework of the European Task Force on Plasma Wall Interaction (EU TF on PWI) efforts are underway to investigate gas balance and fuel retention during discharges, and to compare the data obtained with those from post-mortem analysis of in-vessel components exposed over whole experimental campaigns. This paper summarizes the principal findings from coordinated studies on gas balance and fuel retention from a number of European tokamaks, namely, ASDEX-Upgrade (AUG), JET, TEXTOR and Tore Supra (TS). For most devices, the long-term retention fraction deduced from integrated particle balance is similar to 10-20%. This is larger than the similar to 3-4% deduced from post-mortem analysis of plasma facing components (PFCs). However, from the database available for tokamaks with their main PFCs made of carbon, the important conclusion is that the T inventory limit (set by the working guideline for operations) could be reached in ITER within fewer than 100 discharges. This, therefore, would seriously impact on operation of the device unless efficient T removal processes are developed.
|
|
| 2. |
- Widdowson, A., et al.
(författare)
-
Efficacy of photon cleaning of JET divertor tiles
- 2007
-
Ingår i: Journal of Nuclear Materials. - : Elsevier BV. - 0022-3115 .- 1873-4820. ; 363, s. 341-345
-
Tidskriftsartikel (refereegranskat)abstract
- Photon cleaning by means of a flash-lamp was used for in-situ detritiation of the inner wall tiles of the JET divertor in May 2004. Additional trials were also performed ex-situ in October 2004 on divertor base tiles. Early work confirmed that for pulse energies between 150 J and 300 J some deposited material was removed. To increase the amount of material removed during photon cleaning, further experiments with higher pulse energies (500 J) were performed and are reported here. Analysis of cross sections confirmed a removal rate of 0.04 mu m/pulse, removing similar to 80 mu m from 200 mu m thick deposits over a treatment area of 15 x 10(-4) m(2). During the photon cleaning tests at least 12% of the tritium inventory for the tile was removed. It was also shown that deuterium was desorbed from a depth similar to 7 mu m beyond the depth of material removed. Crown
|
|
| 3. |
- Coad, J. P., et al.
(författare)
-
Erosion and deposition in the JET MkII-SRP divertor
- 2007
-
Ingår i: Journal of Nuclear Materials. - : Elsevier BV. - 0022-3115 .- 1873-4820. ; 363, s. 287-293
-
Tidskriftsartikel (refereegranskat)abstract
- Carbon-13 labelled methane was injected into the outer divertor during a series of H-mode discharges on the last day of operations with the JET MkII-SRP divertor. Tiles from around the vessel were removed during the subsequent shutdown and surface deposits were analysed by IBA techniques and SIMS. First attempts to model the pattern of 13 C deposition using EDGE2D are reported. Erosion of W markers at the outer divertor was observed, with implications for the ITER-like wall experiment planned for JET, whilst thin film growth in the same region has been followed by the effect on infrared measurements. The composition of thick films deposited at the inner divertor during the MkII-SRP campaign, and the migration to the inner corner of the divertor observed by a quartz micro-balance, provide further information on divertor transport. Crown
|
|
| 4. |
- Hirai, T., et al.
(författare)
-
Characterization and heat flux testing of beryllium coatings on Inconel for JET ITER-like wall project
- 2007
-
Ingår i: Physica Scripta. - 0031-8949 .- 1402-4896. ; T128, s. 166-170
-
Tidskriftsartikel (refereegranskat)abstract
- In order to perform a fully integrated material test, JET has launched the ITER-like wall project with the aim of installing a full metal wall during the next major shutdown. The material foreseen for the main chamber wall is bulk Be at the limiters and Be coatings on inconel tiles elsewhere. R&D process comprises global characterization ( structure, purity etc) of the evaporated films and testing of their performance under heat loads. The major results are (i) the layers have survived energy loads of 20 MJ m(-2) which is significantly above the required level of 5 - 10 MJ m(-2), (ii) melting limit of beryllium coating would be at the energy level of 30 MJ m(-2), (iii) cyclic thermal load of 10 MJ m(-2) for up to 50 cycles have not induced any noticeable damage such as flaking or detachment.
|
|
| 5. |
- Likonen, J., et al.
(författare)
-
Structural studies of deposited layers on JET MkII-SRP inner divertor tiles
- 2007
-
Ingår i: Journal of Nuclear Materials. - : Elsevier BV. - 0022-3115 .- 1873-4820. ; 363, s. 190-195
-
Tidskriftsartikel (refereegranskat)abstract
- Deposited layers formed on JET inner divertor tiles during 1998-2004 and 2001-2004 campaigns have been investigated using secondary ion mass spectrometry (SIMS), Rutherford Backscattering (RBS) and optical microscopy. The thickness of the deposit decreases from the top of vertical tile 1 to the bottom and then increases on vertical tile 3 reaching similar to 60 mu m. There are even thicker deposits on the small sloping section of the floor tile 4 that can be accessed by the plasma at the inner divertor legs. Deposited films on divertor inner wall tiles are enriched in Be indicating chemical erosion of C and a multi-step transport of C to the shadowed area on floor tile 4. The films have generally a layered and globular structure in the areas with plasma contact.
|
|
| 6. |
- Piazza, G., et al.
(författare)
-
R&D on tungsten plasma facing components for the JET ITER-like wall project
- 2007
-
Ingår i: Journal of Nuclear Materials. - : Elsevier BV. - 0022-3115 .- 1873-4820. ; 367, s. 1438-1443
-
Tidskriftsartikel (refereegranskat)abstract
- Currently, the primary ITER materials choice is a full beryllium main wall with carbon fibre composite at the divertor strike points and tungsten on the upper vertical targets and dome. The full tungsten divertor option is a possibility for the subsequent D-T phase. Neither of the ITER material combinations of first wall and divertor materials has ever been tested in a tokamak. To collect operational experience at JET with ITER relevant material combination (Be, C and W) would reduce uncertainties and focus the preparation for ITER operations. Therefore, the ITER-like wall project has been launched to install in JET a tungsten divertor and a beryllium main wall. This paper describes the R&D activities carried out for the project to develop an inertially cooled bulk tungsten divertor tile, to fully characterise tungsten coating technologies for CFC divertor tiles and to develop erosion markers for use as diagnostics on beryllium tiles.
|
|
| 7. |
- Fortuna, E., et al.
(författare)
-
Plasma-induced damage of tungsten coatings on graphite limiters
- 2007
-
Ingår i: Physica Scripta. - 0031-8949 .- 1402-4896. ; T128, s. 162-165
-
Tidskriftsartikel (refereegranskat)abstract
- Vaccum plasma sprayed tungsten coatings with an evaporated sandwich Re - W interlayer on graphite limiter blocks were studied after the experimental campaign in the TEXTOR tokamak. The coating morphology was modified by high-heat loads and co-deposition of species from the plasma. Co-deposits contained fuel species, carbon, boron and silicon. X-ray diffractometer phase analysis indicated the coexistence of metallic tungsten and its carbides (WC and W2C) and boride (W2B). In the Re - W layer the presence of carbon was detected in a several micrometres thick zone. In the overheated part of the limiter, the Re - W layer was transformed into a sigma phase.
|
|
| 8. |
- Fortuna, E., et al.
(författare)
-
Properties of co-deposited layers on graphite high heat flux components at the TEXTOR tokamak
- 2007
-
Ingår i: Journal of Nuclear Materials. - : Elsevier. - 0022-3115 .- 1873-4820. ; 367:B, s. 1507-1511
-
Tidskriftsartikel (refereegranskat)abstract
- The objective of this work was to examine the structure, composition and properties of co-deposited films from the TEXTOR tokamak. Hydrogenated films formed on the toroidal belt pump limiter (ALT-II), and on the ICRF antenna grill were studied using a set of material analysis techniques. Plasma edge diagnostics were used to assess the parameters influencing the film formation during discharges auxiliary heated by ICRF. The essential results are summarized as follows: (i) the distribution of plasma impurities co-deposited in the films is non-uniform and (ii) the surface topography, crystallographic structure, fuel retention and composition (i.e., content of re-deposited plasma impurities) of the films show significant diversity depending on the location where they were formed. These differences are associated with the local geometry, the tokamak operation scenarios and the resulting plasma edge properties.
|
|
| 9. |
- Grisolia, C., et al.
(författare)
-
Treatment of ITER plasma facing components : Current status and remaining open issues before ITER implementation
- 2007
-
Ingår i: Fusion engineering and design. - : Elsevier BV. - 0920-3796 .- 1873-7196. ; 82:15-24, s. 2390-2398
-
Tidskriftsartikel (refereegranskat)abstract
- The in-vessel tritium inventory control is one of the most ITER challenging issues which has to be resolved to fulfil safety requirements. This is due mainly to the presence of carbon as a constituent of plasma facing components (PFCs) which leads to a high fuel permanent retention. For several years now, physics studies and technological developments have been undertaken worldwide in order to develop reliable techniques which could be used in ITER severe environment (magnetic field, vacuum, high temperature) for in situ tritium recovery. The scope of this contribution is to review the present status of these achievements and define the remaining work to be done in order to propose a dedicated work program. Different treatment techniques (chemical treatments, photonic cleaning) will be reviewed. In the frame of ITER, they will be compared in terms of fuel removal rate as well as surface accessibility, type of production (gas or particulates), ability to clean mixed material. And lastly, consequences of bulk trapping observed in tokamak on the techniques currently under development will be addressed.
|
|
| 10. |
- Hirai, T., et al.
(författare)
-
R&D on full tungsten divertor and beryllium wall for JET ITER-like wall project
- 2007
-
Ingår i: Fusion engineering and design. - : Elsevier BV. - 0920-3796 .- 1873-7196. ; 82:15-24, s. 1839-1845
-
Tidskriftsartikel (refereegranskat)abstract
- The ITER reference materials have been tested separately in tokamaks, plasma simulators, ion beams and high heat flux test beds. In order to perform a fully integrated material test JET has launched the ITER-like Wall Project with the aim of installing a full metal wall during the next major shutdown. As a result of R&D projects in 2005-2006, bulk tungsten tiles are foreseen at the outer horizontal target and tungsten coating at the other divertor tiles. In some regions of the main chamber, beryllium coated Inconel tiles and bulk beryllium tiles are utilised which include marker tiles as erosion diagnostics. This paper gives an overview of the R&D carried out in the frame of the ITER-like Wall Project on the development of an inertially cooled bulk tungsten tile design and the characterization of tungsten and beryllium coating technologies.
|
|
