| 1. |
- Widdowson, A., et al.
(författare)
-
Experience of handling beryllium, tritium and activated components from JET ITER like wall
- 2016
-
Ingår i: Physica Scripta. - : Institute of Physics Publishing (IOPP). ; T167
-
Konferensbidrag (refereegranskat)abstract
- JET components are removed periodically for surface analysis to assess material migration and fuel retention. This paper describes issues related to handling JET components and procedures for preparing samples for analysis; in particular a newly developed procedure for cutting beryllium tiles is presented. Consideration is also given to the hazards likely due to increased tritium inventory and material activation from 14 MeV neutrons following the planned TT and DT operations (DTE2) in 2017. Conclusions are drawn as to the feasibility of handling components from JET post DTE2.
|
|
| 2. |
- Beal, J., et al.
(författare)
-
Deposition in the inner and outer corners of the JET divertor with carbon wall and metallic ITER-like wall
- 2016
-
Ingår i: Physica Scripta. - : IOP PUBLISHING LTD. - 0031-8949 .- 1402-4896. ; T167
-
Tidskriftsartikel (refereegranskat)abstract
- Rotating collectors and quartz microbalances (QMBs) are used in JET to provide time-dependent measurements of erosion and deposition. Rotation of collector discs behind apertures allows recording of the long term evolution of deposition. QMBs measure mass change via the frequency deviations of vibrating quartz crystals. These diagnostics are used to investigate erosion/deposition during JET-C carbon operation and JET-ILW (ITER-like wall) beryllium/tungsten operation. A simple geometrical model utilising experimental data is used to model the time-dependent collector deposition profiles, demonstrating good qualitative agreement with experimental results. Overall, the JET-ILW collector deposition is reduced by an order of magnitude relative to JET-C, with beryllium replacing carbon as the dominant deposit. However, contrary to JET-C, in JET-ILW there is more deposition on the outer collector than the inner. This reversal of deposition asymmetry is investigated using an analysis of QMB data and is attributed to the different chemical properties of carbon and beryllium.
|
|
| 3. |
- Bernardo, J., et al.
(författare)
-
Ion temperature and toroidal rotation in JET's low torque plasmas
- 2016
-
Ingår i: Review of Scientific Instruments. - : AIP Publishing. - 0034-6748 .- 1089-7623. ; 87:11
-
Tidskriftsartikel (refereegranskat)abstract
- This paper reports on the procedure developed as the best method to provide an accurate and reliable estimation of the ion temperature T-i and the toroidal velocity v(phi) from Charge-eXchange Recombination Spectroscopy (CXRS) data from intrinsic rotation experiments at the Joint European Torus with the carbon wall. The low impurity content observed in such plasmas, resulting in low active CXRS signal, alongside low Doppler shifts makes the determination of Ti and v(phi) particularly difficult. The beam modulation method will be discussed along with the measures taken to increase photon statistics and minimise errors from the absolute calibration and magneto-hydro-dynamics effects that may impact the CXRS passive emission.
|
|
| 4. |
- Figueiredo, J., et al.
(författare)
-
JET diagnostic enhancements in preparation for DT operations
- 2016
-
Ingår i: Review of Scientific Instruments. - : AMER INST PHYSICS. - 0034-6748 .- 1089-7623. ; 87:11
-
Tidskriftsartikel (refereegranskat)abstract
- In order to complete the exploitation of the JET ITER-like Wall and to take full benefit from deuterium-tritium experiments on JET, a set of diagnostic system refurbishments or upgrades is in progress. These diagnostic enhancements focus mainly on neutron, gamma, fast ions, instabilities, and operations support. These efforts intend to provide better spatial, temporal, and energy resolution while increasing measurement coverage. Also previously non-existing capabilities, such as Doppler reflectometry is now available for scientific exploitation. Guaranteeing diagnostic reliability and consistency during the expected DT conditions is also a critical objective of the work and systems being implemented. An overview of status and scope of the ongoing projects is presented.
|
|
| 5. |
- Fortuna-Zalesna, E., et al.
(författare)
-
Dust Survey Following the Final Shutdown of TEXTOR : Metal Particles and Fuel Retention
- 2016
-
Ingår i: Physica Scripta. - : Institute of Physics Publishing (IOPP). - 0031-8949 .- 1402-4896. ; T167
-
Tidskriftsartikel (refereegranskat)abstract
- The work presents results of a broad TEXTOR dust survey in terms of its composition, structure, distribution and fuel content. The dust particles were collected after final shutdown of TEXTOR in December 2013. Fuel retention, as determined by thermal desorption, varied significantly, even by two orders of magnitude, dependent on the dust location in the machine. Dust structure was examined by means of scanning electron microscopy combined with energy-dispersive X-ray spectroscopy, focused ion beam and scanning transmission electron microscopy. Several categories of dust have been identified. Carbon-based stratified and granular deposits were dominating, but the emphasis in studies was on metal dust. They were found in the form of small particles, small spheres, flakes and splashes which formed “comet”-like structures clearly indicating directional effects in the impact on surfaces of plasma-facing components. Nickel-rich alloys from the Inconel liner and iron-based ones from various diagnostic holders were the main components of metal-containing dust, but also molybdenum and tungsten debris were detected. Their origin is discussed.
|
|
| 6. |
- Garcia-Carrasco, Alvaro, et al.
(författare)
-
Impact of helium implantation and ion-induced damage on reflectivity of molybdenum mirrors
- 2016
-
Ingår i: Nuclear Instruments and Methods in Physics Research Section B. - : Elsevier. - 0168-583X .- 1872-9584.
-
Tidskriftsartikel (refereegranskat)abstract
- Molybdenum mirrors were irradiated with Mo and He ions to simulate the effect of neutron irradiation on diagnostic first mirrors in next-generation fusion devices. Up to 30 dpa were produced under molybdenum irradiation leading to a slight decrease of reflectivity in the near infrared range. After 3×1017 cm-2 of helium irradiation, reflectivity decreased by up to 20%. Combined irradiation by helium and molybdenum led to similar effects on reflectivity as irradiation with helium alone. Ion beam analysis showed that only 7% of the implanted helium was retained in the first 40nm layer of the mirror. The structure of the near-surface layer after irradiation was studied with scanning transmission electron microscopy and the extent and size distribution of helium bubbles was documented. The consequences of ion-induced damage on the performance of diagnostic components are discussed.
|
|
| 7. |
- Giacomelli, L., et al.
(författare)
-
Neutron emission spectroscopy of DT plasmas at enhanced energy resolution with diamond detectors
- 2016
-
Ingår i: Review of Scientific Instruments. - : AMER INST PHYSICS. - 0034-6748 .- 1089-7623. ; 87:11
-
Tidskriftsartikel (refereegranskat)abstract
- This work presents measurements done at the Peking University Van de Graaff neutron source of the response of single crystal synthetic diamond (SD) detectors to quasi-monoenergetic neutrons of 14-20 MeV. The results show an energy resolution of 1% for incoming 20 MeV neutrons, which, together with 1% detection efficiency, opens up to new prospects for fast ion physics studies in high performance nuclear fusion devices such as SD neutron spectrometry of deuterium-tritium plasmas heated by neutral beam injection.
|
|
| 8. |
- Hillesheim, J. C., et al.
(författare)
-
Stationary Zonal Flows during the Formation of the Edge Transport Barrier in the JET Tokamak
- 2016
-
Ingår i: Physical Review Letters. - : AMER PHYSICAL SOC. - 0031-9007 .- 1079-7114. ; 116:6
-
Tidskriftsartikel (refereegranskat)abstract
- High spatial resolution Doppler backscattering measurements in JET have enabled new insights into the development of the edge E-r. We observe fine-scale spatial structures in the edge E-r well with a wave number k(r rho i) approximate to 0.4-0.8, consistent with stationary zonal flows, the characteristics of which vary with density. The zonal flow amplitude and wavelength both decrease with local collisionality, such that the zonal flow E x B shear increases. Above the minimum of the L-H transition power threshold dependence on density, the zonal flows are present during L mode and disappear following the H-mode transition, while below the minimum they are reduced below measurable amplitude during L mode, before the L-H transition.
|
|
| 9. |
- Horacek, J., et al.
(författare)
-
Multi-machine scaling of the main SOL parallel heat flux width in tokamak limiter plasmas
- 2016
-
Ingår i: Plasma Physics and Controlled Fusion. - : Institute of Physics Publishing (IOPP). - 0741-3335 .- 1361-6587. ; 58:7
-
Tidskriftsartikel (refereegranskat)abstract
- As in many of today's tokamaks, plasma start-up in ITER will be performed in limiter configuration on either the inner or outer midplane first wall (FW). The massive, beryllium armored ITER FW panels are toroidally shaped to protect panel-to-panel misalignments, increasing the deposited power flux density compared with a purely cylindrical surface. The chosen shaping should thus be optimized for a given radial profile of parallel heat flux, q(parallel to) in the scrape-off layer (SOL) to ensure optimal power spreading. For plasmas limited on the outer wall in tokamaks, this profile is commonly observed to decay exponentially as q(parallel to) = q(0)exp (-r/lambda(omp)(q)), or, for inner wall limiter plasmas with the double exponential decay comprising a sharp near-SOL feature and a broader main SOL width, lambda(omp)(q). The initial choice of lambda(omp)(q), which is critical in ensuring that current ramp-up or down will be possible as planned in the ITER scenario design, was made on the basis of an extremely restricted L-mode divertor dataset, using infra-red thermography measurements on the outer divertor target to extrapolate to a heat flux width at the main plasma midplane. This unsatisfactory situation has now been significantly improved by a dedicated multi-machine ohmic and L-mode limiter plasma study, conducted under the auspices of the International Tokamak Physics Activity, involving 11 tokamaks covering a wide parameter range with R = 0.4-2.8 m, B-0 = 1.2-7.5T, I-p = 9-2500 kA. Measurements of lambda(omp)(q) in the database are made exclusively on all devices using a variety of fast reciprocating Langmuir probes entering the plasma at a variety of poloidal locations, but with the majority being on the low field side. Statistical analysis of the database reveals nine reasonable engineering and dimensionless scalings. All yield, however, similar predicted values of lambda(omp)(q) mapped to the outside midplane. The engineering scaling with the highest statistical significance, lambda(omp)(q) = 10(P-tot/V(W m(-3)))(-0.38)(a/R/kappa)(1.3), dependent on input power density, aspect ratio and elongation, yields lambda(omp)(q) = [7, 4, 5] cm for I-p = [2.5, 5.0, 7.5] MA, the three reference limiter plasma currents specified in the ITER heat and nuclear load specifications. Mapped to the inboard midplane, the worst case (7.5 MA) corresponds to lambda(omp)(q) similar to 57 +/- 14 imp mm, thus consolidating the 50 mm width used to optimize the FW panel toroidal shape.
|
|
| 10. |
- Kwak, Sehyun, et al.
(författare)
-
Bayesian modelling of the emission spectrum of the Joint European Torus Lithium Beam Emission Spectroscopy system
- 2016
-
Ingår i: Review of Scientific Instruments. - : American Institute of Physics (AIP). - 0034-6748 .- 1089-7623. ; 87:2
-
Tidskriftsartikel (refereegranskat)abstract
- A Bayesian model of the emission spectrum of the JET lithium beam has been developed to infer the intensity of the Li I (2p-2s) line radiation and associated uncertainties. The detected spectrum for each channel of the lithium beam emission spectroscopy system is here modelled by a single Li line modified by an instrumental function, Bremsstrahlung background, instrumental offset, and interference filter curve. Both the instrumental function and the interference filter curve are modelled with non-parametric Gaussian processes. All free parameters of the model, the intensities of the Li line, Bremsstrahlung background, and instrumental offset, are inferred using Bayesian probability theory with a Gaussian likelihood for photon statistics and electronic background noise. The prior distributions of the free parameters are chosen as Gaussians. Given these assumptions, the intensity of the Li line and corresponding uncertainties are analytically available using a Bayesian linear inversion technique. The proposed approach makes it possible to extract the intensity of Li line without doing a separate background subtraction through modulation of the Li beam.
|
|
