| 1. |
- Stolen, Reidar, et al.
(författare)
-
Solcelleteknologi og brannsikkerhet
- 2018
-
Rapport (övrigt vetenskapligt/konstnärligt)abstract
- Bruken av solcelleteknologi er i stor vekst i Norge. I denne studien er branntekniske utfordringer ved bruk av solcelleteknologi undersøkt, med hensyn på brannstart, brannspredning og brannslokking. Studien danner et kunnskapsgrunnlag for å ivareta brannsikkerheten under montering, drift og under slokkeinnsats, samt for å utforme et enhetlig og tydelig regelverk. Resultatene fra studien viser:Brannstart: Solcelleinstallasjoner inneholder mange koblingspunkt, som kan være potensielle tennkilder, og en liten mengde brennbare materialer. Dermed er det som trengs til stede for å starte en brann. Det er viktig at alle kontaktpunkter i solcelleinstallasjonen er robuste og tåler den påkjenningen de blir utsatt for gjennom sin levetid uten at det oppstår dårlig kontakt som kan føre til brann.Brannspredning: For utenpåmonterte solcellemoduler er det ofte en åpen luftspalte mellom modul og bygning. Dersom det er en brann i denne luftspalten, vil varmen kunne bli akkumulert, noe som kan føre til raskere og større brannspredning enn om bygningsoverflaten ikke hadde vært tildekket. I fullskalaforsøk med solcellemoduler montert på tak spredte brannen seg under hele arealet som var dekket av moduler, men stoppet da den nærmet seg kanten av dette arealet. Dette illustrerer viktigheten av at områder med solceller utenpå en bygning blir seksjonert for å unngå brannspredning. Eventuelt kan det benyttes mindre brennbare materialer på taket under solcellemodulene for å motvirke den økte varmepåkjenningen som solcellemodulene gir. Luftspalten mellom modul og bygning kan potensielt også gi endringer i luftstrømningen langs bygget, som igjen kan påvirke brannspredningen.Brannslokking: Brannvesenet har behov for informasjon om det er solcelleinstallasjon i bygget og hvilke deler av det elektriske anlegget som kan være spenningssatt. Under slokkeinnsats må brannvesenet ta hensyn til berøringsfare, og fare for at det kan oppstå lysbuer og andre feil som kan føre til nye antennelsespunkt. Ferskvann kan brukes som slokkemiddel, dette må spyles fra minimum 1 meters avstand med spredt stråle og minimum 5 meters avstand med samlet stråle. Solcellemoduler kan komplisere brannslokking ved at de danner en fysisk barriere mellom brannvesenet og brannen, samt fordi det må tas hensyn til plassering av spenningssatte komponenter. Når disse punktene er tatt høyde for, bør ikke utenpåmonterte solcelleinstallasjoner være et problem.Videre arbeid: For utenpåmonterte solcelleinstallasjoner, er det lite forskning på vertikal montering (på fasader), og hvordan en eventuell endret branndynamikk kan påvirke brannspredning og slokking. Videre er det i dag økende bruk av bygningsintegrerte solcelleinstallasjoner, noe som gir mange mulige nye utfordringer for brannsikkerheten og for regelverk, ettersom solcellen da er en del av bygningskroppen, samtidig som den er en elektrisk komponent. Tysk statistikk tyder på at brannrisiko for slike installasjoner kan være større enn for utenpåmonterte solcelleinstallasjoner, og dette vil det derfor være viktig å undersøke nærmere.
|
|
| 2. |
- Eivazihollagh, Alireza, et al.
(författare)
-
On chelating surfactants : Molecular perspectives and application prospects
- 2019
-
Ingår i: Journal of Molecular Liquids. - : Elsevier BV. - 0167-7322 .- 1873-3166. ; 278, s. 688-705
-
Tidskriftsartikel (refereegranskat)abstract
- Chelating agents, molecules that very strongly coordinates certain metal ions, are used industrially as well as in consumer products to minimize disturbances and increase performance of reactions and applications. The widely used sequestering agents, nitrilotriacetic acid (NTA), ethylenediaminetetraacetic acid (EDTA) and diethylenetriaminepentaacetic acid (DTPA) belong to this branch of readily water-soluble compounds. When these chemical structures also have hydrophobic parts, they are prone to adsorb at air-water interfaces and to self-assemble. Such bifunctional molecules can be called chelating surfactants and will have more extended utilization prospects than common chelating agents or ordinary ionic surfactants. The present review attempts to highlight the fundamental behavior of chelating surfactants in solution and at interfaces, and their very specific interactions with metal ions. Methods to recover chelating surfactants from metal chelates are also described. Moreover, utilization of chelating surfactants in applications for metal removal in environmental engineering and mineral processing, as well as for metal control in the fields of biology, chemistry and physics, is exemplified and discussed.
|
|
| 3. |
- André, Hampus, 1989
(författare)
-
Resource and Environmental Impacts of Resource-Efficiency Measures Applied to Electronic Products
- 2018
-
Licentiatavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Natural resources such as ecosystems, land, water and metals underpin the functioning of economies and human well-being, and are becoming increasingly scarce due to growth in population and affluence. Metals are increasingly demanded for their specific properties as modern technology develops. The dependence on metals is of growing concern due to the environmental impacts related, for example, to energy use and local impacts from mining, as well as the scarcity risks posed by socio-economic, geological and geopolitical constraints. Thus, there is a clear need to use metals and other natural resources more efficiently. The vision of a circular economy has been proposed as a way to do this, for example by improving durability, reusing, repairing and recycling. Such so-called resource-efficiency (RE) measures are commonly assumed to be environmentally beneficial, although the evidence is not plentiful. It is plausible that focusing on recirculating products and materials could shift burdens to other environmental impacts or life cycle stages. It has therefore been argued that a life cycle-based approach, such as in life cycle assessment (LCA), is useful to critically assess the environmental implications of RE measures. LCA aims to quantify the environmental impacts of products over their entire life cycles - from cradle to grave - assessing a wide range of impacts such as toxicity, climate change and metal resource use. For metal resource use, however, there are a number of perspectives as to what constitutes the actual environmental problem. These perspectives are represented in a variety of life cycle impact assessment methods (LCIA) which have previously been shown to give diverging results. Electronic products are emblematic of metal resource use challenges since they deploy a broad spectrum of scarce metals. This thesis aims to provide knowledge on the potential for RE measures to reduce the environmental impacts of electronic products, by addressing the following research questions: (1) What resource-efficiency measures result in reduced potential environmental impacts and resource use – for what types of products and under what conditions? (2) How does extended use of electronic products through design for increased technical lifetime, reuse and repair affect environmental impacts, particularly metal resource use? (3) How does the application of different LCIA methods for metal resource use influence interpretations of resource-efficiency measures applied to electronic products? This thesis builds on three appended papers which are all based on comparative assessments of resource efficiency, studied as resource use and environmental impacts per function delivered, using LCA and material flow analysis. The results indicate that extended use of electronic products through increasing technical lifetimes, reusing and repairing, is generally resource-efficient. Exceptions may occur, however, if extended use is insufficient to motivate impacts from producing more durable products or spare parts. Use extension of electronic products leads to resource efficiency in two distinct ways: through the intended use extension and by increasingly steering material flows into recycling. Further resource efficiency could be realised by combining RE measures over the entire life cycles of products. With regards to metal resource use, the choice of LCIA method can influence the interpretation of the results of RE measures for electronic products. Therefore, it is advisable to use several complementary LCIA methods to minimise the risks of overlooking potentially important resources issues. Furthermore, better understanding and transparency of such issues is valuable in order to provide more comprehensive information to decision-makers.
|
|
| 4. |
- Ahrné, Karin, et al.
(författare)
-
Tillstånd och trender för arter och deras livsmiljöer – rödlistade arter i Sverige 2015
- 2015
-
Rapport (övrigt vetenskapligt/konstnärligt)abstract
- 2015 års upplaga av den svenska rödlistan är den fjärde i ordningen. Den är baserad på IUCN:s rödlistningskriterier och revideras vart femte år. I rödlistan bedöms risken som enskilda arter av djur, växter och svampar löper att försvinna från Sverige. Bedömningen utförs av ArtDatabankens medarbetare i samverkan med över 100 externa experter, indelade i 14 expertkommittéer för olika organismgrupper. Under arbetet med 2015 års rödlista har tillstånd och trender bedömts för 21 600 arter och 1 318 lägre taxa (apomiktiska arter, underarter och varieteter), sammanlagt ca 22 900 taxa. Av de bedömda arterna klassificerades 2 029 som hotade (kategorierna CR, EN och VU) och 4 273 som rödlistade (inkluderar även kategorierna NT, RE och DD). Förhållandet mellan antalet rödlistade och antalet bedömda arter ar 19,8 %, vilket är ungefär samma värde som 2010 och 2005. I denna rapport jämförs antalet och andelen rödlistade arter mellan olika organismgrupper, biotoper, substrat och påverkansfaktorer. Texten ar indelad i en allmän del och åtta kapitel inriktade på olika landskapstyper. Landskapstyperna utgör en grov indelning av landets miljöer enligt följande kategorier: Skog, Jordbrukslandskap, Urbana miljöer, Fjäll, Våtmarker, Sötvatten, Havsstränder och Havsmiljöer. Skogen och jordbrukslandskapet är de artrikaste landskapstyperna med 1 800 respektive 1 400 arter som har en stark anknytning dit, och ytterligare flera hundra arter som förekommer där mer sporadiskt. De faktorer som påverkar flest rödlistade arter i Sverige är skogsavverkning och igenväxning, som båda utgör ett hot mot vardera ca 30 % av de rödlistade arterna. Avverkning minskar arealen av skog där naturliga strukturer och naturlig dynamik upprätthålls, och den orsakar därmed förlust av livsmiljöer. Igenväxning orsakas av ett antal faktorer, bland annat upphörande hävd (bete och slåtter), gödsling, trädplantering och brist på naturliga störningsregimer som t.ex. regelbundna översvämningar kring vattendrag och sjöar. Andra viktiga påverkansfaktorer är fiske, torrläggning av våtmarker, tillbakagång hos värdarter (främst alm och ask som drabbats av invasiva svampsjukdomar), klimatförändringar och konkurrens från invasiva arter. IUCN:s rödlisteindex beräknas för ett urval av de bedömda organismgrupperna. Rödlisteindex visar att skillnaderna mellan rödlistorna från 2000, 2005, 2010 och 2015 är små. Ett par undantag finns dock. Groddjur och stora däggdjur har fått en något förbättrad situation sedan 2000. Totalt förefaller det ändå som att trycket mot Sveriges artstock har förblivit relativt konstant under de senaste 15 åren.
|
|
| 5. |
- Johansson, Björn, 1975, et al.
(författare)
-
Power Level Sampling of Metal Cutting Machines for Data Representation in Discrete Event Simulation
- 2015
-
Ingår i: International Journal of Production Research. - : Informa UK Limited. - 0020-7543 .- 1366-588X. ; 53:23, s. 7060-7070
-
Tidskriftsartikel (refereegranskat)abstract
- An extension to the application area for discrete event simulation (DES) has been ongoing since the last decade and focused only on economic aspects to include ecologic sustainability. With this new focus, additional input parameters, such as electrical power consumption of machines, are needed. This paper aim at investigating how NC machine power consumption should be represented in simulation models of factories. The study includes data-sets from three different factories. One factory producing truck engine blocks, one producing brake disc parts for cars and one producing forklift components. The total number of data points analysed are more than 2,45,000, where of over 1,11,000 on busy state for 11 NC machines. The low variability between busy cycles indicates that statistical representations are not adding significant variability. Furthermore, results show that non-value-added activities cause a substantial amount of the total energy consumption, which can be reduced by optimising the production flow using dynamic simulations such as DES.
|
|
| 6. |
- Skagestad, Ragnhild, 1978, et al.
(författare)
-
GCCSI Webinar: Cutting Cost of CO2 Capture in Process Industry (CO2stCap) Project overview & first results for partial CO2 capture at integrated steelworks
- 2017
-
Annan publikation (övrigt vetenskapligt/konstnärligt)abstract
- GCCSI Webinar: Cutting Cost of CO2 Capture in Process Industry (CO2stCap) Project overview & first results for partial CO2 capture at integrated steelworks This publication has the format of a webinar: The CO2StCap project is a four year initiative carried out by industry and academic partners with the aim of reducing capture costs from CO2 intensive industries (more information here). The project, led by Tel-Tek, is based on the idea that cost reduction is possible by capturing only a share of the CO2 emissions from a given facility, instead of striving for maximized capture rates. This can be done in multiple ways, for instance by capturing only from the largest CO2 sources at individual multi-stack sites utilising cheap waste heat or adapting the capture volumes to seasonal changes in operations. The main focus of this research is to perform techno-economic analyses for multiple partial CO2 capture concepts in order to identify economic optimums between cost and volumes captured. In total for four different case studies are developed for cement, iron & steel, pulp & paper and ferroalloys industries. The first part of the webinar gave an overview of the project with insights into the cost estimation method used. The second part presented the iron & steel industry case study based on the Lulea site in Sweden, for which waste-heat mapping methodology has been used to assess the potential for partial capture via MEA-absorption. Capture costs for different CO2 sources were discussed, demonstrating the viability of partial capture in an integrated steelworks.
|
|
| 7. |
- de Klijn-Chevalerias, M., et al.
(författare)
-
The Dutch approach for assessing and reducing environmental impacts of building materials
- 2017
-
Ingår i: Building and Environment. - : Elsevier BV. - 0360-1323. ; 111, s. 147-159
-
Tidskriftsartikel (refereegranskat)abstract
- Buildings are one of the largest consumers of energy and materials, and hence they are also one of the largest contributors to negative environmental impacts. Traditionally, energy consumed by buildings during their operation phase was the most significant in their lifecycles and far exceeded the embodied energy. However, in contemporary low-energy buildings, the embodied energy is proportionally higher because of the prevalent use of energy-intensive materials. To determine the embodied energy and environmental impacts of building materials, the Dutch have developed an assessment method, which has also been adapted by BREEAM-NL. This paper offers an overview of the Dutch approach for assessing the environmental impacts of building materials and demonstrates its practical application. The use of the Dutch Assessment Method to identify, and quantify materials-related design improvements has been demonstrated through an exemplifying case study. It has been identified that the environmental impact of a building is largely influenced by the material choices made at the early design stage of the project.
|
|
| 8. |
- Salzer, Corinna, 1984, et al.
(författare)
-
Innovation for Low-Rise Construction in the Urban Tropics: Utilization of Structural Bamboo for Cost-Efficient Housing
- 2015
-
Ingår i: 8th Conference of the International Forum on Urbanism (IFoU). - Basel, Switzerland : MDPI.
-
Konferensbidrag (refereegranskat)abstract
- This paper deals with a cost-efficient construction technology using load bearing bamboo for urban low-rise housing in tropical Asia-Pacific. The potential of the technology to be applied at larger scale is discussed at the example of the Philippines as pilot country for its application. The assessment of alternative construction methods such as this one is motivated by a tremendous need for more affordable, sustainable and resilient housing around the globe. The urban poor, being the most underserved group in need of housing, often cannot afford conventional building technologies offered by the formal industry. Using locally available bamboo as structural component within the introduced standardized and quality controlled construction method is an entry point to provide performing and safe housing at lower cost. The paper highlights, however, that cost-efficiency and technical performance are not the only requirements for innovations to succeed on a market, especially due to the complex challenge of urban poor housing. Through learnings from the construction of 50 houses in the Philippines and interviews with various stakeholders along the value chain of the technology, barriers and opportunities for a scale-up are retrieved. For this paper, a conflated none-exhaustive overview of the identified aspects is documented. It was found that both barriers and opportunities directly linked to this technology are closely tied to a complex local value chain which ranges from upstream supply of raw material to downstream customer acceptance. The pilot application has shown further, that participatory product development reduces the acceptance barrier significantly by directly addressing the needs of low income customers. Material and skills availability, enabling policies and approval by legal entities as well as sustainability in supply of the organic raw material play important roles too. This complex set of interlinked aspects needs to be addressed according to targets in implementation-pace, and -scale as well as its intended social value creation. While multi-stakeholder participation is required for a successful up-scaling, a facilitating social enterprise, providing knowledge and services around the technology, can guide through the up-scaling.
|
|
| 9. |
- Liu, Qianyun, et al.
(författare)
-
Roadside assessment of a modern city bus fleet: Gaseous and particle emissions
- 2019
-
Ingår i: Atmospheric Environment: X. - : Elsevier BV. - 2590-1621. ; 3
-
Tidskriftsartikel (refereegranskat)abstract
- © 2019 The Authors In many cities worldwide, modern fleets have been introduced to reduce gaseous and particle emissions from city buses. To date, most emission studies are limited to a few vehicles, making a statistically significant assessment of control options difficult, especially under real-world driving conditions. Exhaust emissions of 234 individual city buses were measured under real-world stop-and-go traffic conditions at a bus stop in Gothenburg, Sweden. The buses comprised models fulfilling Euro III-VI and EEV (Enhanced Environmentally Friendly Vehicle) standards with different engine technologies, fuels, and exhaust after-treatment systems, and also included hybrid-electric buses (HEV). Both gaseous (NOx, CO, HC, and SO2) and size-resolved particle number (PN) and mass (PM) emission factors (EF) were calculated for vehicles using compressed natural gas (CNG), diesel (DSL), Rapeseed Methyl Ester (RME) and Hydro-treated Vegetable Oil (HVO) equipped with various after-treatment technologies, e.g., diesel particulate filter (DPF), selective catalytic reduction (SCR) and exhaust gas recirculation (EGR) systems. The highest median EFPN was obtained from Euro VHEV-HVO-SCR buses (MdEFPN = 18×1014 # kg-1) when their combustion engines were used though 53% of their accelerations were below detection limits indicating the use of their electrical engine. The highest MdEFPM was obtained from the Euro V-DSL-SCR buses (MdEFPM = 150 mg kg-1) and the lowest from EEV-CNG buses (below detection threshold) and Euro VIHEV-HVO- SCR+EGR+DPF buses (MdEFPM = 19 mg kg-1). The highest MdEFNOx was obtained from the Euro V-RME-SCR (MdEFNOx = 30 g kg-1) and Euro VHEV-HVO-SCR buses (MdEFNOx = 24 g kg-1), and the lowest from CNG buses (MdEFNOx = 4.8 g kg-1) and Euro VIHEV-HVO-SCR+EGR+DPF buses (MdEFNOx = 7.4 g kg-1). Hybrid buses can give higher PN emissions compared to traditional diesel engines, likely due to downsized combustion engines. Replacing diesel by biodiesel fuel reduced MdEFPM significantly but increased MdEFNOx which may be due to the higher combustion temperature and oxygen contents of the fuel (for RME). Overall, the EEV-CNG buses performed the best regarding both the MdEF and low contribution to the high emitters. It was also found that a small (5%) proportion of the buses contributed significantly (14-30%) to the total emissions. Identification and monitoring the maintenance of the high emitters in the fleets should be considered for the improvement of air quality.
|
|
| 10. |
- Shahbazi, Sasha, et al.
(författare)
-
Material efficiency in manufacturing: swedish evidence on potential, barriers and strategies
- 2016
-
Ingår i: Journal of Cleaner Production. - : Elsevier BV. - 0959-6526 .- 1879-1786. ; 127, s. 438-450
-
Tidskriftsartikel (refereegranskat)abstract
- Improved material efficiency is a key to improve the circular economy and capturing value in industry. Material efficiency reduces the generation of industrial waste, the extraction and consumption of resources, and energy demands and carbon emissions. However, material efficiency in the manufacturing sector, as a means of improving the recyclability, reusability, reduction and prevention of industrial waste, is little understood. This study aims to investigate, on a micro-level, further material efficiency improvement opportunities, barriers and strategies in selected manufacturing companies in Sweden, focusing on increasing waste segregation into high quality circulated raw material. Improvement opportunities at large global manufacturing companies are investigated; barriers hindering material efficiency improvement are identified and categorized at two levels; and strategies that have been deployed at manufacturing companies are reviewed. Empirical findings reveal (1) further potential for improving material efficiency through higher segregation of residual material from mixed and low quality fractions (on average, 26% of the content of combustible waste, in weight, was plastics; 8% and 6% were paper and cardboard, respectively); (2) the most influential barriers are within budgetary, information, management, employee, engineering, and communication clusters; (3) a lack of actual material efficiency strategy implementation in the manufacturing companies. According to our analysis, the majority of barriers are internal and originate within the manufacturing companies, therefore they can be managed (and eradicated if possible) with sufficient resources in terms of man hours, education and investment, better operational and environmental (waste) management, better internal communication and information sharing, and deployment of material efficiency strategies.
|
|
