| 1. |
- Okda, Sherif, et al.
(författare)
-
Testing of the Aerodynamic Characteristics of an Inflatable Airfoil Section
- 2020
-
Ingår i: Journal of Aerospace Engineering. - 1943-5525 .- 0893-1321. ; 33:5
-
Tidskriftsartikel (refereegranskat)abstract
- Inflatable structures are characterized by being light and easy to manufacture and deploy. Hence, they find many applications in aerospace and aeronautical engineering. In this paper, an inflatable segment with a The National Advisory Committee for Aeronautics (NACA) 0021 airfoil cross-section is designed, fabricated, and tested. The geometrical accuracy of the manufactured inflatable segment is measured using laser scanning. Measurements show that the average normalized error of the chord length and thickness are 2.97% and 0.554%, respectively. The aerodynamic behavior of the inflatable segment is then tested in a wind tunnel at different wind speeds and angles of attack. Lift forces are measured using a six-component balance, while the drag forces are calculated from the wake measurements. The lift and drag coefficients of the inflatable section are compared to those of a standard NACA 0021 airfoil. Finally, flow visualization is examined at different angles of attack using two methods: smoke and tufts. Both methods show that flow separation starts at 15° and full stall occurs at 25°. Results indicate that inflatables can find more applications in the design and construction of aerodynamic structures, such as wings.
|
|
| 2. |
- Wadekar, Sandip, 1989
(författare)
-
Large-Eddy Simulation of Gasoline Fuel Spray Injection at Ultra-High Injection Pressures
- 2021
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Gasoline direct injection is a state-of-the-art technique that reduces hydrocarbon and particulate emissions. However, further improvement is needed to meet current as well as future emission regulations. A prominent solution is to increase the fuel injection pressure which allows faster fuel droplet atomization, quick evaporation and improves fuel-air mixture formation under realistic engine conditions. In this work, the gasoline fuel injection process at ultra-high injection pressures ranging from 200 to 1500 bar was analyzed using numerical models. In particular, the Large-Eddy Simulation (LES) method, with the standard Smagorinsky turbulence model, was utilized using the Eulerian formulation for the continuous phase. The discrete droplet phase was treated using a Lagrangian formulation together with spray sub-models. In the first part of study, spray was injected into an initially quiescent constant volume chamber using two different nozzle hole shape geometries: divergent and convergent. The numerical results were calibrated by reproducing experimentally observed liquid penetration length and efforts were made to understand the influence of ultra-high injection pressures on spray development. The calibrated models were then used to investigate the impact of ultra-high injection pressures on mean droplet sizes, droplet size distribution, spray-induced large-scale eddies and entrainment rate. The results showed that, at ultra-high injection pressures, the mean droplet sizes were significantly reduced and the droplets achieving very high velocities. Integral length scales of spray-induced turbulence and air entrainment rate were better for the divergent-shaped injector, and considerably larger at higher injection pressures compared to lower ones. In the second part of the study, four consecutive full-cycle cold flow LES simulations were carried out to generate realistic turbulence inside the engine cylinder. The first three cycles were ignored, with the fourth cycle being used to model the injection of the fuel using the divergent-shaped injector only (which was found to be better in the previous part of this study) at different injection pressures. In addition to the continuous gas phase (Eulerian) and the dispersed liquid (Lagrangian), the liquid film feature (Finite-Area) was used to model the impingement of fuel spray on the engine walls and subsequent liquid film formation. The simulation results were used to evaluate spray-induced turbulence, fuel-air mixing efficiency and the amount of liquid mass deposited on the walls. The limitation of the high-pressure injection technique with respect to liquid film formation was optimized using a start of injection (SOI) sweep. Overall results showed that the mixing efficiency increased at high injection pressure and that SOI should occur between early injection and late injection to optimize the amount of mass being deposited on the engine walls.
|
|
| 3. |
- Etikyala, Sreelekha, 1991
(författare)
-
Particulate Formation in GDI Engines
- 2022
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- The need to comply with stringent emission regulations while improving fuel economy and reducing criteria pollutant emissions from transportation presents a major challenge in the design of gasoline Direct Injection (DI) engines because of the adverse effects of ultrafine Particulate Number (PN) emissions on human health and other environmental concerns. With upcoming advances in vehicle electrification, it may be the case that electric vehicles completely replace all current vehicles powered by internal combustion engines ensuring zero emissions. In the meantime, Gasoline Direct Injection (GDI) engines have become the primary mode of transportation using gasoline as they offer better fuel economy while also providing low CO2 emissions. However, GDI engines tend to produce relatively high PN emissions when compared to conventional Port Fuel Injection (PFI) engines, largely because of challenges associated with in-cylinder liquid fuel injection. Cold-starts, transients, and high load operation generate a disproportionate share of PN emissions from GDI engines over a certification cycle. The mechanisms of PN formation during these stages must therefore be understood to identify solutions that reduce overall PN emissions in order to comply with increasingly strict emissions standards. This work presents experimental studies on particulate emissions from a naturally aspirated single cylinder metal gasoline engine run in a homogeneous configuration. The engine was adapted to enable operation in both DI and PFI modes. In PFI mode, injection was performed through a custom inlet manifold about 50 cm from the cylinder head to maximize the homogeneity of the fuel-air mixture. The metal head was eventually modified by incorporating an endoscope that made it possible to visualize the combustion process inside the cylinder. The experimental campaigns were structured to systematically isolate and clarify PN formation mechanisms. Tests were initially performed in steady state mode to obtain preliminary insights and to screen operating conditions before conducting transient tests. Particulate emissions were measured and correlated with the images obtained through endoscope visualization where possible. Key objectives of these studies were to find ways of reducing PN formation by increasing combustion stability. It was found that by avoiding conditions that cause wall wetting with liquid fuel, PN emissions can be substantially reduced during both steady state operation and transients. Warming the coolant and injecting fuel at later timings reduced PN emissions during warmup and cold transient conditions. Additionally, experiments using fuel blends with different oxygenate contents showed that the chemical composition of the fuel strongly influences particulate formation under steady state and transient conditions, and that this effect is load-dependent. Overall, the results obtained in this work indicate that wall wetting is the dominant cause of particulate formation inside the cylinder and that fuel-wall interactions involving the piston, cylinder walls, and valves during fuel injection account for a significant proportion of PN emissions in the engine raw exhaust.
|
|
| 4. |
- Li, Xiaojian, 1991, et al.
(författare)
-
Installation effects on engine design
- 2020
-
Konferensbidrag (övrigt vetenskapligt/konstnärligt)abstract
- Increasing the engine bypass ratio is one way to improve propulsive efficiency. However, an increase in the bypass ratio (BPR) has usually been associated with an increase in the fan diameter. Consequently, there can be a notable increase in the impact of the engine installation on the overall aircraft performance. In order to achieve a better balance between those factors, it requires novel nacelle and engine design concepts. This report mainly reviews installation effects on engine design. Firstly, the installation effects assessment methods are introduced. Then, the installation effects on engine cycle design, intake design and exhaust design are sequentially reviewed.
|
|
| 5. |
- Tillig, Fabian, 1984, et al.
(författare)
-
Design, operation and analysis of wind-assisted cargo ships
- 2020
-
Ingår i: Ocean Engineering. - : Elsevier BV. - 0029-8018. ; 211:1, s. 1-23
-
Tidskriftsartikel (refereegranskat)abstract
- This study presents a novel approach to analytically capture aero- and hydrodynamic interaction effects on wind-assisted ships. Low aspect ratio wing theory is applied and modified to be used for the prediction of lift and drag forces of hulls sailing at drift angles. Aerodynamic interaction effects are captured by analytically solving the Navier-Stokes equation for incompressible, potential flow. The developed methods are implemented to a 4 degrees-of-freedom performance prediction model called “ShipCLEAN”, including a newly developed method for rpm control of Flettner rotors on a ship to maximize fuel savings. The accuracy of the model is proven by model- and full-scale verification. To present the variability of the model, two case study ships, a tanker and a RoRo, are equipped with a total of 11 different arrangements of Flettner rotors. The fuel savings and payback times are assessed using realistic weather from ships traveling on a Pacific Ocean route (tanker) and Baltic Sea route (RoRo). The results verify the importance of using a 4 degrees-of-freedom ship performance model, aero- and hydrodynamic interaction and the importance of controlling the rpm of each rotor individually. Fuel savings of 30% are achieved for the tanker, and 14% are achieved for the RoRo.
|
|
| 6. |
- Ottersten, Martin, 1981, et al.
(författare)
-
Inlet Gap Influence on Low-Frequency Flow Unsteadiness in a Centrifugal Fan
- 2022
-
Ingår i: Aerospace. - : MDPI AG. - 2226-4310. ; 9:12
-
Tidskriftsartikel (refereegranskat)abstract
- In this study, unsteady low-frequency characteristics in a voluteless low-speed centrifugal fan operating at a high mass flow rate are studied with improved delayed detached eddy simulation (IDDES). This study is motivated by a recent finding that the non-uniformly distributed pressure inside this type of fan could be alleviated by improving the gap geometry. The present simulation results show that the velocity magnitudes of the gap have distinct low and high regions. Intensive turbulent structures are developed in the low-velocity regions and are swept downstream along the intersection between the blade and shroud, on the pressure side of the blade. Eventually, the turbulence gives rise to a high-pressure region near the blade’s trailing edge. This unsteady flow behavior revolves around the fan rotation axis. Additionally, its period is 5% of the fan rotation speed, based on the analysis of the time history of the gap velocity magnitudes and the evolution of the high-pressure region. The same frequency of high pressure was also found in previous experimental measurements. To the authors’ knowledge, this is the first time that the trigger of the gap turbulence, i.e., the unsteady local low velocity, has been determined.
|
|
| 7. |
- Hadadpour, Ahmad
(författare)
-
Spray combustion with multiple-injection in modern engine conditions
- 2020
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Combustion of fuel in diesel engines emits substances harmful to the environment such as soot. These emissions can be reduced by either in-cylinder treatments or after-treatments. One of the common in-cylinder treatments is multiple-injection, which divides a single fuel injection to multiple smaller injections. There are many open questions on the physical processes of the ignition, combustion and emissions of diesel spray flame with multiple injections. The current PhD project aims at studying these processes using large-eddy simulations (LES) and strives to answer some of the open questions. To develop a fast and robust LES tool for this study, a new method is formulated for spray combustion simulation. This method is developed based on the flamelet-generated manifold (FGM) method and the Eulerian stochastic fields (ESF) method. The new ESF/FGM method relaxes some of the substantial assumptions in conventional FGM, while it still keeps the computational costs at a reasonable level for engineering applications. Additionally in this work, a new reaction progress variable for FGM models is proposed by using local oxygen consumption, and the advantages and limitations of this progress variable are explored. Spray-A from Engine Combustion Network (ECN) which is designed to mimic modern engine conditions is chosen as the baseline case for simulations. In this case, liquid n-dodecane, which is a diesel surrogate, is injected into a high-pressure constant-volume vessel. The comparison of simulation results with experimental measurements shows that the ESF/FGM method with the new progress variable can predict the spray combustion characteristics such as ignition delay time, ignition location, lift-off length, pressure rise and thermochemical structure of the spray flame, accurately. After validation of simulation results against experimental measurements, the new ESF/FGM and other available turbulence-combustion simulation tools are applied to simulate multiple-injection spray combustion. Different multiple-injection strategies are investigated by systematically changing the injection timing. The effects of applying each strategy on the ignition, combustion, mixing and emissions are investigated. The results show that in split-injection and post-injection strategies the major physical reason for reduction of soot is better air entrainment and lower local equivalence ratio. It is shown that increasing the dwell time and retarding it toward the end of injection can enhance this effect. On the contrary, for the pre-injection strategies, shortening the ignition delay time of the main injection reduces its pre-mixing and increases its soot formation. In these strategies, the high-temperature region from the pre-injection combustion can increase soot oxidation of the main injection fuel, only if this region is not cooled down as a result of air entrainment during dwell time. Therefore, in such cases shortening the dwell time decreases net soot emissions.
|
|
| 8. |
- Li, Xiaojian, 1991, et al.
(författare)
-
A New Method for Impeller Inlet Design of Supercritical CO2 Centrifugal Compressors in Brayton Cycles
- 2020
-
Ingår i: Energies. - : MDPI AG. - 1996-1073 .- 1996-1073. ; 13:19
-
Tidskriftsartikel (refereegranskat)abstract
- Supercritical Carbon Dioxide (SCO2) is considered as a potential working fluid in next generation power and energy systems. The SCO2 Brayton cycle is advantaged with higher cycle efficiency, smaller compression work, and more compact layout, as compared with traditional cycles. When the inlet total condition of the compressor approaches the critical point of the working fluid, the cycle efficiency is further enhanced. However, the flow acceleration near the impeller inducer causes the fluid to enter two-phase region, which may lead to additional aerodynamic losses and flow instability. In this study, a new impeller inlet design method is proposed to achieve a better balance among the cycle efficiency, compressor compactness, and inducer condensation. This approach couples a concept of the maximum swallowing capacity of real gas and a new principle for condensation design. Firstly, the mass flow function of real gas centrifugal compressors is analytically expressed by non-dimensional parameters. An optimal inlet flow angle is derived to achieve the maximum swallowing capacity under a certain inlet relative Mach number, which leads to the minimum energy loss and a more compact geometry for the compressor. Secondly, a new condensation design principle is developed by proposing a novel concept of the two-zone inlet total condition for SCO2 compressors. In this new principle, the acceptable acceleration margin (AAM) is derived as a criterion to limit the impeller inlet condensation. The present inlet design method is validated in the design and simulation of a low-flow-coefficient compressor stage based on the real gas model. The mechanisms of flow accelerations in the impeller inducer, which form low-pressure regions and further produce condensation, are analyzed and clarified under different operating conditions. It is found that the proposed method is efficient to limit the condensation in the impeller inducer, keep the compactness of the compressor, and maintain a high cycle efficiency.
|
|
| 9. |
- Sarkar, Saptarshi, 1992, et al.
(författare)
-
Transient torque reversals in indirect drive wind turblnes
- 2023
-
Ingår i: Wind Energy. - 1099-1824 .- 1095-4244. ; 26, s. 691-716
-
Tidskriftsartikel (refereegranskat)abstract
- The adverse effect of transient torque reversals (TTRs) оп wind turЬine gearboxes сап Ье severe due to their magnitude and rapid occurrence compared with other equipment. The primary damage is caused to the bearings as the bearing loaded zone rapidly changes its direction. Other components are also affected Ьу TTRs (such as gear tooth); however, its impact оп bearings is the largest. While the occurrence and severity of TTRs are acknowledged in the industry, there is а lack of academic literature оп their initiation, propagation and the associated risk of damage. Furthermore, in the wide range of operation modes of а wind turЬine, it is not known which modes сап lead to TTRs. Further, the interdependence of TTRs оп environmental loading like the wind is also not reported. This paper aims to address these unknowns Ьу expanding оп the understanding of TTRs using а high-fidelity numerical model of an indirect drive wind turЬine with а douЬly fed induction generator (DFIG). То this end, а multibody model of the drivetrain is developed in SIMPACK. The model of the drivetrain is explicitly coupled to state-of-the-art wind turЬine simulator OpenFAST and а grid-connected DFIG developed in MATLAB®'s Simulink® allowing а coupled analysis of the electromechanical system. А metric termed slip risk duration is proposed in this paper to quantify the risk associated with the TTRs. The paper first investigates а wide range of IEC design load cases to uncover which load cases сап lead to TTRs. lt was found that emergency stops and symmetric grid voltage drops сап lead to TTRs. Next, the dependence of the TTRs оп inflow wind parameters is investigated using а sensitivity analysis. lt was found that the instantaneous wind speed at the onset of the grid fault or emergency shutdown was the most influential factor in the slip risk duration. The investigation enaЫes the designer to predict the occurrence of TTRs and quantify the associated risk of damage. The paper concludes with recommendations for utility-scale wind turЬines and directions for future research.
|
|
| 10. |
- Shahroozi, Zahra, 1992-
(författare)
-
Survivability control using data-driven approaches and reliability analysis for wave energy converters
- 2024
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- Wave energy, with five times the energy density of wind and ten times the power density of solar, offers a compelling carbon-free electricity solution. Despite its advantages, ongoing debates surround the reliability and economic feasibility of wave energy converters (WECs). To address these challenges, this doctoral thesis is divided into four integral parts, focusing on optimizing the prediction horizon for power maximization, analyzing extreme waves' impact on system dynamics, ensuring reliability, and enhancing survivability in WECs.Part I emphasizes the critical importance of the prediction horizon for maximal power absorption in wave energy conversion. Using generic body shapes and modes, it explores the effect of dissipative losses, noise, filtering, amplitude constraints, and real-world wave parameters on the prediction horizon. Findings suggest achieving optimal power output may be possible with a relatively short prediction horizon, challenging traditional assumptions.Part II shifts focus to WEC system dynamics, analyzing extreme load scenarios. Based on a 1:30 scaled wave tank experiment, it establishes a robust experimental foundation, extending into numerical assessment of the WEC. Results underscore the importance of damping to alleviate peak forces. Investigating various wave representations highlights conservative characteristics of irregular waves, crucial for WEC design in extreme sea conditions.Part III explores the computational intricacies of environmental design load cases and fatigue analyses for critical mechanical components of the WEC. The analysis is conducted for hourly sea state damage and equivalent two-million-cycle loads. Finally, a comparison of safety factors between the ultimate limit state and fatigue limit state unfolds, illustrating the predominant influence of the ultimate limit state on point-absorber WEC design.Part IV, centers on elevating survivability strategies for WECs in extreme wave conditions. Three distinct controller system approaches leverage neural networks to predict and minimize the line force. Distinct variations emerge in each approach, spanning from rapid detection of optimal damping to integrating advanced neural network architectures into the control system with feedback. The incorporation of a controller system, refined through experimental data, showcases decreases in the line force, providing a practical mechanism for real-time force alleviation.This thesis aims to contribute uniquely to the goal of advancing wave energy conversion technology through extensive exploration.
|
|
