| 1. |
- Abyaneh, Morteza Y
(författare)
-
Homogeneous and Heterogeneous Nucleation in Electrocrystallization
- 2024
-
Ingår i: Electrochimica Acta. - : Elsevier. - 0013-4686 .- 1873-3859.
-
Tidskriftsartikel (refereegranskat)abstract
- The belief amongst most electrochemists that the appropriate models, representing “homogeneous” and “heterogeneous” nucleation in the context of electrocrystallization, are spherical and spherical-cap shapes, respectively, is challenged. A proper foundation for modelling heterogeneous nucleation is introduced. The free energy required for the formation of a nucleus within an indent is derived and compared with that required for the formation of a nucleus onto a flat surface of an electrode. It is shown for the first time, using the classical theory of nucleation, that a much smaller free energy is required for nucleating within an indent on the surface of an electrode than nucleating onto a flat electrode surface. The applicability of the model, with the corresponding equations, to nucleation in the context of electrocrystallization is established.
|
|
| 2. |
- Adeniyi, Omotayo, et al.
(författare)
-
Engineering of layered iron vanadate nanostructure for electrocatalysis : simultaneous detection of methotrexate and folinic acid in blood serum
- 2023
-
Ingår i: Electrochimica Acta. - : Elsevier. - 0013-4686 .- 1873-3859.
-
Tidskriftsartikel (refereegranskat)abstract
- In this study, nanostructure kazakhstanite-like iron vanadate (FexV3xOy.H2O) was synthesized and calcined at different temperatures (100-800 °C) in a nitrogen atmosphere. The material was used to modify screen-printed carbon electrodes to achieve an electrocatalytic effect on the surface. The relationship between calcination conditions and the catalytic performance of the electrode towards the oxidation of chemotherapeutic drugs, including methotrexate (MTX) and folinic acid (FA), was studied. Various spectroscopic, microscopic, and electrochemical methods were used to characterize the synthesized materials. The results show that calcination induces changes in the electronic structure, nanostructure morphology, electroactive surface area, and electrocatalytic performance of the material. Screen-printed carbon electrode modified with FexV3xOy calcinated at 450 °C (SPC/FexV3xOy-450) was used to develop a voltammetric sensor for the determination of MTX and FA in blood serum. The response of the SPC/FexV3xOy-450 towards the electrooxidation of MTX and FA was the highest in comparison to the bare SPC and SPC/FexV3xOy calcined at other temperatures. The SPC/FexV3xOy-450 exhibited a linear relationship over a wide concentration range: 0.005-200 µM for MTX and 0.05-200 µM for FA. The detection limit was 2.85 nM for MTX and 7.79 nM for FA. Compared to conventional methods, the SPC/FexV3xOy-450 sensor had a short response time (5 min) for simultaneous detection of MTX and FA without signal interferences from coexisting electroactive compounds. The accurate and precise determination of MTX in the presence of FA confirmed the potential clinical applications of SPC/FexV3xOy-450 for therapeutic drug monitoring during chemotherapy.
|
|
| 3. |
- Ahmed, Bilal, et al.
(författare)
-
Electrochemical activation of commercial graphite sheets for supercapacitive applications
- 2022
-
Ingår i: Electrochimica Acta. - : PERGAMON-ELSEVIER SCIENCE LTD. - 0013-4686 .- 1873-3859. ; 431
-
Tidskriftsartikel (refereegranskat)abstract
- Carbon-based substrates are widely used as current collectors for high-performance energy storage materials in supercapacitors. However, these substrates exhibit negligible charge storage due to inferior electrochemical activity and small surface area. Herein, electrochemical activation is utilized to enhance the electrochemical activity of - inherently inactive - commercial graphite sheets for supercapacitive applications. The results reveal that the electrochemically activated graphite sheets render a 30-fold increase in areal capacitance, i.e., from 22 to 447 mF cm(-2), which can be ascribed to the activation of graphite oxide functional groups on the surface. Also, the influence of electrochemical activation time on electrochemical performance is explored in detail, followed by the fabrication and characterization of symmetric supercapacitors based on the optimum process parameters in single-cell and tandem configurations, demonstrating the potential of electrochemically activated graphite sheets in practical applications.
|
|
| 4. |
- Atak, Gamze, et al.
(författare)
-
Electrochromic tungsten oxide films prepared by sputtering : Optimizing cycling durability by judicious choice of deposition parameters
- 2021
-
Ingår i: Electrochimica Acta. - : Elsevier. - 0013-4686 .- 1873-3859. ; 367
-
Tidskriftsartikel (refereegranskat)abstract
- Thin films of W oxide were prepared by reactive DC magnetron sputtering (5 cm-diameter W target), and their electrochromic (EC) properties were investigated in an electrolyte of LiClO4 in propylene carbonate. The purpose of the study was to elucidate the role of critical deposition parameters-oxygen/argon gas flow ratio for the sputter plasma Gamma, total pressure in the sputter plasma p(tot) , and sputtering power P-s - on the EC performance with foci on electrochemical cycling durability and optical modulation range Delta T. Specifically, we used 0.15 <= Gamma <= 0.90, 5 <= p(tot) <= 30 mTorr, and 200 <= P-s <= 400 W and studied cycling durability for up to 500 voltammetric cycles in the range 2.0-4.0 V vs. Li/Li+ together with optical properties at a wavelength of 528 nm. Most significantly, we discovered that a judicious choice of deposition parameters could yield films with superior cycling durability. Thus a similar to 300 nm-thick film prepared at Gamma = 0.90, p(tot) = 10 mTorr, and P-s = 200 W showed Delta T approximate to 65% after an initial "training" during similar to 100 voltammetric cycles; higher values of p(tot), on the other hand, yielded films whose Delta Ts degraded by similar to 10% during the cycling, and a lower value of p(tot) led to dark films with only marginal electrochromism. Hence our work delineates a pathway towards W oxide films with excellent durability of the EC properties.
|
|
| 5. |
- Atapour, Masoud, et al.
(författare)
-
Corrosion and metal release investigations of selective laser melted 316L stainless steel in a synthetic physiological fluid containing proteins and in diluted hydrochloric acid
- 2020
-
Ingår i: Electrochimica Acta. - : Elsevier BV. - 0013-4686 .- 1873-3859. ; 354
-
Tidskriftsartikel (refereegranskat)abstract
- The corrosion and metal release characteristics of additively manufactured stainless steels are key factors for their applicability in biomedical applications. The effect of building direction on the microstructure, corrosion behavior and metal release of selective laser melted (SLM) AISI 316L stainless steel were therefore investigated in a protein-rich synthetic body fluid (PBS+BSA, pH 7.3) and in diluted hydrochloric acid (HCl, pH 1.5). A multi-analytical approach was applied to characterize SLM 316L surfaces printed in different building directions (denoted XY and XZ) and a post heat treated SLM surface (XZ-HT) compared with wrought surfaces. All SLM specimens revealed an austenitic microstructure without any amounts of delta-ferrite and without large-angled grain boundaries in contrast to the wrought 316L surface. The building direction strongly affected the grain size distribution due to the temperature gradients in the melt pools. The SLM 316L specimens released initially slightly less Fe, Cr and Ni compared with the wrought 316L specimen. Slightly less metal was released from the heat treated SLM specimen (XZ-HT) specimen compared to the other SLM specimens. Relatively high amounts of released Cr were observed in PBS+BSA, most probably attributed to protein-bound Cr, whereas substantially more Ni was released in HCl compared to PBS+BSA due to pitting corrosion and a reduced surface oxide thickness. The surface oxide composition of as-printed SLM specimens was strongly dependent on the building direction and the post heat treatment, whereas no differences were observed after abrasion either among the SLM specimens or compared with the wrought 316L specimen. Cr became in all cases enriched within the outermost surface oxide in PBS+BSA and strongly enriched in the HCl solution, coupled to a strongly reduced amount of released metals with time. The heat treated SLM specimen (XZ-HT) gained a superior charge transfer resistance, the lowest passive current density, and the highest OCP value among all specimens. In HCl, the SLM specimens showed a lower pitting susceptibility compared to the wrought specimens. No pitting was observed in PBS+BSA. No differences in corrosion or metal release characteristics were observed related to the building direction of abraded SLM specimens.
|
|
| 6. |
- Atapour, Masoud, et al.
(författare)
-
Stainless steel in simulated milk and whey protein solutions - Influence of grade on corrosion and metal release
- 2020
-
Ingår i: Electrochimica Acta. - : PERGAMON-ELSEVIER SCIENCE LTD. - 0013-4686 .- 1873-3859. ; 331
-
Tidskriftsartikel (refereegranskat)abstract
- Reactions at the biointerfaces between stainless steel and protein-rich dairy products, which contain whey proteins, are important to consider in terms of food safety and material grade selection. Changes in corrosion behavior, metal release, and surface composition of austenitic (AISI 316 L), ferritic (AISI 430), and lean duplex (LDX 2101) stainless steels in simulated milk (SMS) and whey protein solution were investigated. The amount of released metals and the corrosion susceptibility increased according to 2101 < 316 L < 430. All grades revealed low corrosion rates in the whey protein solution without any sign of active/metastable corrosion. Pitting corrosion was evident for 430 in SMS. The total amount of released metals (iron, chromium, and nickel) was significantly higher in whey protein solution compared with SMS. This suggests the metal release process to be mainly governed by complexation reactions. Nickel was preferentially released compared to its bulk composition fraction for both 316 L and 2101 in the highly complexing SMS. Reduced metal release rates with time correlated with the enrichment of chromium in the surface oxide. The extent of metal release was for all metals substantially lower than release limits of metals stipulated in health regulations related to the use of alloys and metals in food-related environments.
|
|
| 7. |
- Aung, Soe Ko Ko, et al.
(författare)
-
Reduced hysteresis and enhanced air stability of low-temperature processed carbon-based perovskite solar cells by surface modification
- 2023
-
Ingår i: Electrochimica Acta. - : Elsevier. - 0013-4686 .- 1873-3859. ; 443
-
Tidskriftsartikel (refereegranskat)abstract
- Low temperature processed carbon-based perovskite solar cells (C-PSCs) have gained great interest because of low cost and ease of fabrication. By replacing the Au electrode with carbon, stable solar cells suited for mass-production process can be made. However, power conversion efficiencies (PCEs) of C-PSCs still lag behind that of PSCs with Au contact.Here we explore low temperature (<= 150 degrees C) processed C-PSCs with, where a two-step method is used to prepare mixed-ion lead perovskite films, with tin oxide (SnO2) electron transport layer, poly(3-hexylthiophene-2,5-diyl) (P3HT) hole transport layer and carbon electrode, resulting in devices with a PCE of 14.0%. Moreover, hexyl trimethylammonium bromide (HTAB) was introduced to improve the interface between perovskite and P3HT. Perovskite grains were remarkably enlarged into micrometer-size and defects were reduced. As a result, a champion PCE of 16.1% was obtained, mainly due to enhanced fill factor from 0.67 to 0.73. The interface modification by HTAB molecule is an effective way to passivate the perovskite defects and facilitate the carrier transport at the perovskite/HTL interface. Unencapsulated devices showed excellent stability over 1500 h stored under ambient air (relative humidity -50 +/- 10%).
|
|
| 8. |
- B. Araujo, Rafael, et al.
(författare)
-
Elucidating the role of Ni to enhance the methanol oxidation reaction on Pd electrocatalysts
- 2020
-
Ingår i: Electrochimica Acta. - : Elsevier BV. - 0013-4686 .- 1873-3859. ; 360
-
Tidskriftsartikel (refereegranskat)abstract
- Amongst promising available technologies enabling the transition to renewable energy sources, electrochemical oxidation of alcohols, in a direct fuel cell or in an electrolysis reaction (H-2 production), can be an economically and sustainable alternative to currently used technologies. In this work, we highlight the advantages of a Pd-Ni bimetallic electrocatalyst for methanol electrooxidation - a convenient choice due to the low cost of Ni combined with the observed acceptable catalytic performance of Pd. We report a synergistic effort between experiments and theoretical calculations based on density functional theory to provide an in-depth understanding - at the atomistic level - of the origin of the enhanced electrochemical activity of methanol electrooxidation using the bimetallic catalysts Pd3Ni and PdNi over pure Pd. Cyclic voltammograms and High-Performance Liquid Chromatography (HPLC) demonstrate higher activity towards methanol electrooxidation with increased Ni concentration and, furthermore, higher selectivity for CO2. These effects are understood by: 1) changes in the methanol oxidation reaction mechanism. 2) Mitigation or suppression of CO poisoning on the Pd-Ni alloys as compared to the pure Pd catalyst. 3) A stronger tendency towards highly oxidized intermediates for the alloys. These findings elucidate the effects of a bimetallic electrocatalyst for alcohol electrooxidation as well as unambiguously suggest PdNi as a more cost-effective alternative electrocatalyst.
|
|
| 9. |
|
|
| 10. |
- Bertoli, Luca, et al.
(författare)
-
Combination of solid polymer electrolytes and lithiophilic zinc for improved plating/stripping efficiency in anode-free lithium metal solid-state batteries
- 2023
-
Ingår i: Electrochimica Acta. - : Elsevier BV. - 0013-4686 .- 1873-3859. ; 464
-
Tidskriftsartikel (refereegranskat)abstract
- Anode-free lithium metal batteries and solid-state batteries represent some of the most promising alternatives to the current Li-ion technology. The possibility to reach high energy density, due to the exploitation of Li-metal plating/stripping and the elimination of excess anode material, motivate the interest at both academic and in-dustrial levels. Despite these favourable properties, the use of Li-metal has always been extremely challenging and inefficient. This becomes particularly relevant in anode-free systems where no excess of lithium is introduced in the cell. The efficiency and quality of the deposition process is therefore of utmost importance. To optimize the Li-metal plating process, a combination of solid polymer electrolytes and a lithiophilic metal is applied herein, using in situ deposition of a zinc interlayer from a PEO-based SPE to modify the Cu current collector. Im-provements in specific capacity, coulombic efficiency and cyclability with the addition of zinc as lithiophilic metal is verified in full anode-free solid-state Li-batteries, while plating/stripping in half-cell configuration provides additional insights into the relevant mechanisms. The exploitation of the in situ deposited lithiophilic layer reveals an innovative and practical optimization strategy for the future of anode-free solid-state batteries.
|
|
