| 1. |
- Albinsson, Anton, 1989, et al.
(författare)
-
Evaluation of vehicle-based tyre testing methods
- 2019
-
Ingår i: Proceedings of the Institution of Mechanical Engineers. Part D, Transport engineering. - : SAGE Publications. - 2041-2991 .- 0954-4070. ; 233:1, s. 4-17
-
Tidskriftsartikel (refereegranskat)abstract
- The demand for reduced development time and cost for passenger cars increases the strive to replace physical testing with simulations. This leads to requirements on the accuracy of the simulation models used in the development process. The tyres, the only components transferring forces from the road to the vehicle, are a challenge from a modelling and parameterization perspective. Tests are typically performed on flat belt tyre testing machines. Flat belt machines offers repeatable and reliable measurements. However, differences between the real world road surface and the flat belt can be expected. Hence, when using a tyre model based on flat belt measurements in full vehicle simulations, differences between the simulations and real prototype testing can be expected as well. Vehicle-based tyre testing can complement flat belt measurements by allowing reparameterization of tyre models to a new road surface. This paper describes an experimental vehicle-based tyre testing approach that aims to parameterize force and moment tyre models compatible with the standard tyre interface. Full-vehicle tests are performed, and the results are compared to measurements from a mobile tyre testing rig on the same surface and to measurements on a flat belt machine. The results show that it is feasible to measure the inputs and outputs to the standard tyre interface on a flat road surface with the used experimental setup. The flat belt surface and the surface on the test track show similar characteristics. The maximum lateral force is sensitive to the chosen manoeuvres, likely due to temperature differences and to vibrations at large slip angles. For tyre models that do not model these effects, it is vital to test the tyres in a manoeuvre that creates comparable conditions for the tyres as the manoeuvre in which the tyre model will be used.
|
|
| 2. |
- Albinsson, Anton, 1989, et al.
(författare)
-
Tire Lateral Vibration Considerations in Vehicle-Based Tire Testing
- 2019
-
Ingår i: Tire Science and Technology. - : The Tire Society. - 0090-8657 .- 1945-5852. ; 47:3, s. 211-231
-
Tidskriftsartikel (refereegranskat)abstract
- Vehicle-based tire testing can potentially make it easier to reparametrize tire models for different road surfaces. A passenger car equipped with external sensors was used to measure all input and output signals of the standard tire interface during a ramp steer maneuver at constant velocity. In these measurements, large lateral force vibrations are observed for slip angles above the lateral peak force with clear peaks in the frequency spectrum of the signal at 50 Hz and at multiples of this frequency. These vibrations can lower the average lateral force generated by the tires, and it is therefore important to understand which external factors influence these vibrations. Hence, when using tire models that do not capture these effects, the operating conditions during the testing are important for the accuracy of the tire model in a given maneuver. An Ftire model parameterization of tires used in vehicle-based tire testing is used to investigate these vibrations. A simple suspension model is used together with the tire model to conceptually model the effects of the suspension on the vibrations. The sensitivity of these vibrations to different operating conditions is also investigated together with the influence of the testing procedure and testing equipment (i.e., vehicle and sensors) on the lateral tire force vibrations. Note that the study does not attempt to explain the root cause of these vibrations. The simulation results show that these vibrations can lower the average lateral force generated by the tire for the same operating conditions. The results imply that it is important to consider the lateral tire force vibrations when parameterizing tire models, which does not model these vibrations. Furthermore, the vehicle suspension and operating conditions will change the amplitude of these vibrations and must therefore also be considered in maneuvers in which these vibrations occur.
|
|
| 3. |
- Albinsson, Anton, 1989, et al.
(författare)
-
Validation of vehicle-based tyre testing methods
- 2019
-
Ingår i: Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering. - : SAGE Publications. - 2041-2991 .- 0954-4070. ; 233:1, s. 18-27
-
Tidskriftsartikel (refereegranskat)abstract
- The development process for passenger cars is both time- and resource-consuming. Full vehicle testing is an extensive part of the development process that consumes large amount of resources, especially within the field of vehicle dynamics and active safety. By replacing physical testing with complete vehicle simulations, both the development time and cost can potentially be reduced. This requires accurate simulation models that represent the real vehicle. One major chal- lenge with full vehicle simulation models is the representation of tyres in terms of force and moment generation. The force and moment generation of the tyres is affected by both operating conditions and road surface. Vehicle-based tyre testing offers a fast and efficient way to rescale force and moment tyre models to different road surfaces, in this study the Pacejka 2002 model. The resulting tyre model is sensitive to both the operating conditions during testing and the road surface used. This study investigates the influence of the slip angle sweep rate and road surface on the lateral tyre force characteristics of the fitted tyre model. Tyre models fitted to different manoeuvres are compared and the influence on the full vehicle behaviour is investigated in IPG Carmaker. The results show that by using the wrong road surface, the resulting tyre model can end up outside the tolerances specified by the ISO standard for vehicle simulation model verifi- cation in steady-state cornering. The use of Pacejka 2002 models parameterized in a steady-state manoeuvre to simulate the vehicle behaviour in sine-with-dwell manoeuvres is also discussed.
|
|
