| 1. |
- Andersson, Mattias, et al.
(författare)
-
Mixed C60/C70 based fullerene acceptors in polymer bulk-heterojunction solar cells
- 2012
-
Ingår i: Organic Electronics: physics, materials, applications. - : Elsevier BV. - 1566-1199 .- 1878-5530. ; 13:12, s. 2856-2864
-
Tidskriftsartikel (refereegranskat)abstract
- Different mixtures of identically substituted C60 and C70 based fullerens have been used as acceptors in three polymer: fullerene systems that strongly express various performance limiting aspects of bulk heterojunction solar cells. Results are correlated with, and discussed in terms of e.g. morphology, charge separation, and charge transport. In these systems, there appears to be no relevant differences in either mobility or energy level positions between the identically substituted C60 and C70 based fullerenes tested. Examples of how fullerene mixtures influence the nano-morphology of the active layer are given. An upper limit to the open circuit voltage that can be obtained with fullerenes is also suggested.
|
|
| 2. |
- Anselmo, Ana Sofia, 1980-, et al.
(författare)
-
Tuning the Vertical Phase Separation in Polyfluorene: Fullerene Blend Films by Polymer Functionalization
- 2011
-
Ingår i: Chemistry of Materials. - Washington : American Chemical Society (ACS). - 1520-5002 .- 0897-4756. ; 23:9, s. 2295-2302
-
Tidskriftsartikel (refereegranskat)abstract
- Achieving control over the nanomorphology of blend films of the fullerene derivative [6,6]-phenyl C61-butyric acid methyl ester, PCBM, with light-absorbing conjugated polymers is an important challenge in the development of efficient solution-processed photovoltaics. Here, three new polyfluorene copolymers are presented, tailored for enhanced miscibility with the fullerene through the introduction of polymer segments with modified side chains, which enhance the polymer's polar character. The composition of the spincoated polymer:PCBM films is analyzed with dynamic secondary ion mass spectrometry (dSIMS). The dSIMS depth profiles demonstrate compositional variations perpendicular to the surface plane, as a result of vertical phase separation, directed by the substrate. These variations propagate to a higher degree through the film for the polymers with a larger fraction of modified side chains. The surface composition of the films is studied by Near-edge X-ray absorption fine structure spectroscopy (NEXAFS). Quantitative analysis of the NEXAFS spectra through a linear combination fit with the spectra of the pure components yields the surface composition. The resulting blend ratios reveal polymer-enrichment of the film surface for all three blends, which also becomes stronger as the polar character of the polymer increases. Comparison of the NEXAFS spectra collected with two different sampling depths shows that the vertical composition gradient builds up already in the first nanometers underneath the surface of the films. The results obtained with this new series of polymers shed light on the onset of formation of lamellar structures in thin polymer:PCBM films prepared from highly volatile solvents.
|
|
| 3. |
- Hedman, Erik, et al.
(författare)
-
Sudden gains in internet-based cognitive behaviour therapy for severe health anxiety
- 2014
-
Ingår i: Behaviour Research and Therapy. - : Elsevier. - 0005-7967 .- 1873-622X. ; 54, s. 22-29
-
Tidskriftsartikel (refereegranskat)abstract
- OBJECTIVE: A sudden gain is defined as a large and stable individual improvement occurring between two consecutive treatment sessions. Sudden gains have been shown to predict better long-term improvement in several treatment studies, including cognitive behavioural therapy for depression and anxiety disorders, but have not been studied in the treatment of health anxiety or any form of internet-based cognitive behavioural therapy. The aim of this study was to investigate the role of sudden gains in internet-based cognitive behavioural therapy for severe health anxiety.METHOD: We examined the occurrence and significance of sudden gains in measures of health anxiety in 81 participants receiving internet-based cognitive behavioural therapy. We compared patients with sudden gains, patients without sudden gains, and patients with gradual gains.RESULTS: Thirteen participants (16%) experienced one sudden gain in health anxiety with individual sudden gains distributed across the treatment. As expected, patients with a sudden gain showed larger improvements than patients without a sudden gain at post-treatment (d = 1.04) and at one-year follow-up (d = 0.91) on measures of health anxiety.CONCLUSIONS: Consistent with previous studies, sudden gains in internet-based cognitive behavioural therapy are associated with significantly larger and stable treatment effects up to one-year follow-up.
|
|
| 4. |
- Hou, Lintao, et al.
(författare)
-
Lateral Phase Separation Gradients in Spin-Coated Thin Films of High-Performance Polymer: Fullerene Photovoltaic Blends
- 2011
-
Ingår i: Advanced Functional Materials. - : Wiley. - 1616-3028 .- 1616-301X. ; 21:16, s. 3169-3175
-
Tidskriftsartikel (refereegranskat)abstract
- In this study, it is demonstrated that a finer nanostructure produced under a rapid rate of solvent removal significantly improves charge separation in a high-performance polymer: fullerene bulk-heterojunction blend. During spin-coating, variations in solvent evaporation rate give rise to lateral phase separation gradients with the degree of coarseness decreasing away from the center of rotation. As a result, across spin-coated thin films the photocurrent at the first interference maximum varies as much as 25%, which is much larger than any optical effect. This is investigated by combining information on the surface morphology of the active layer imaged by atomic force microscopy, the 3D nanostructure imaged by electron tomography, film formation during the spin coating process imaged by optical interference and photocurrent generation distribution in devices imaged by a scanning light pulse technique. The observation that the nanostructure of organic photovoltaic blends can strongly vary across spin-coated thin films will aid the design of solvent mixtures suitable for high molecular-weight polymers and of coating techniques amenable to large area processing.
|
|
| 5. |
- Inganäs, Olle, et al.
(författare)
-
Polymer Photovoltaics with Alternating Copolymer/Fullerene Blends and Novel Device Architectures
- 2010
-
Ingår i: Advanced Materials. - : Wiley. - 0935-9648 .- 1521-4095. ; 22:20, s. E100-E116
-
Tidskriftsartikel (refereegranskat)abstract
- The synthesis of novel conjugated polymers, designed for the purpose of photovoltaic energy conversion, and their properties in polymer/fullerene materials and photovoltaic devices are reviewed. Two families of main chain polymer donors, based on fluorene or phenylene and donor-acceptor-donor comonomers in alternating copolymers, are used to absorb the high-energy parts of the solar spectrum and to give high photovoltages in combinations with fullerene acceptors in devices. These materials are used in alternative photovoltaic device geometries with enhanced light incoupling to collect larger photocurrents or to enable tandem devices and enhance photovoltage.
|
|
| 6. |
- Jarvid, Markus, 1985, et al.
(författare)
-
Evaluation of the Performance of Several Object Types for Electrical Treeing Experiments
- 2013
-
Ingår i: IEEE Transactions on Dielectrics and Electrical Insulation. - 1558-4135 .- 1070-9878. ; 20:5, s. 1712-1719
-
Tidskriftsartikel (refereegranskat)abstract
- A comparison of the efficiency of various types of object for studying the development of electrical trees in polymers is presented. Two types of newly developed wire-plane objects are investigated and compared with two versions of the traditionally used needle-needle objects. The two needle-needle objects are prepared according to ASTM standard and act as references, whereas the alternative objects rely on use of an ultra-thin tungsten wire (10 and 20 µm) in the test objects for providing the highly divergent electric stress. In one type of those object the wire extends from a semiconducting tab embedded in the tested material, while in the other type, the embedded wire is extended and connected externally by means of a copper tape. The comparison is made using cross linked polyethylene (XLPE) for the testing purposes. The wire type objects provide some promising advantages, including parallel formation of several electrical trees and an exposure of a larger material volume. Further advantages include the considerable simplification of both the manufacturing and the measuring procedures. Among the newly developed test objects, the one without the semiconducting tab is considered most advantageous as it allows for more accurate treeing initiation measurements at a lower voltage level. On the other hand the disadvantage is a formation of kinks on the wire that results from polyethylene shrink during sample preparation, which may yield some difficulties in correctly estimating the local field strength locally as well as straining the surrounding material. However the multitude of electric trees formed in each sample allows to easily discard the trees growing at such imperfections in following data analyses. Although finding a statistical method that makes good use of all the data poses a challenge, a suggested approach is presented.
|
|
| 7. |
- Johansson, Anette, 1977, et al.
(författare)
-
A Versatile System for Electrical Treeing Tests under AC and DC Stress Using Wire Electrodes
- 2011
-
Ingår i: 8th International Conference on Insulated Power Cables, Jicable’11, 19 – 23 June 2011, Versailles - France.
-
Konferensbidrag (övrigt vetenskapligt/konstnärligt)abstract
- An alternative method to evaluate electrical treeing in solid dielectric materials is presented. Here the test sample utilises a wire electrode for creating the necessary high divergent electric field. This introduces a different preparation method and several of the disadvantages with the traditional needle sample can be avoided. Together with the test object a versatile test setup for both AC and DC measurements is illustrated. This alternative method has proven successful and an evaluation thereof as well as a comparative study between the two electrode systems is included.
|
|
| 8. |
- Müller, Christian, et al.
(författare)
-
Influence of Molecular Weight on the Performance of Organic Solar Cells Based on a Fluorene Derivative
- 2010
-
Ingår i: Advanced Materials for Optics and Electronics. - : Wiley. - 1616-301X .- 1616-3028. ; 20:13, s. 2124-2131
-
Tidskriftsartikel (refereegranskat)abstract
- The performance of organic photovoltaic (OPV) bulk-heterojunction blends comprising a liquid-crystalline fluorene derivative and a small-molecular fullerene is found to increase asymptotically with the degree of polymerization of the former. Similar to various thermodynamic transition temperatures as well as the light absorbance of the fluorene moiety, the photocurrent extracted from OPV devices is found to strongly vary with increasing oligomer size up to a number average molecular weight, M-n approximate to 10 kg mol(-1), but is rendered less chain-length dependent for higher M-n as the fluorene derivative gradually adopts polymeric behavior.
|
|
| 9. |
- Tang, Zheng, et al.
(författare)
-
Interlayer for Modified Cathode in Highly Efficient Inverted ITO-Free Organic Solar Cells
- 2012
-
Ingår i: Advanced Materials. - : Wiley. - 0935-9648 .- 1521-4095. ; 24:4, s. 554-
-
Tidskriftsartikel (refereegranskat)abstract
- Inverted polymer solar cells with a bottom metal cathode modified by a conjugated polymer interlayer show considerable improvement of photocurrent and fill factor, which is due to hole blocking at the interlayer, and a modified surface energy which affects the nanostructure in the TQ1/[70]PCBM blend.
|
|
| 10. |
- Tang, Zheng, et al.
(författare)
-
Semi-Transparent Tandem Organic Solar Cells with 90% Internal Quantum Efficiency
- 2012
-
Ingår i: Advanced Energy Materials. - : Wiley. - 1614-6840 .- 1614-6832. ; 2:12, s. 1467-1476
-
Tidskriftsartikel (refereegranskat)abstract
- Semi-transparent (ST) organic solar cells with potential application as power generating windows are studied. The main challenge is to find proper transparent electrodes with desired electrical and optical properties. In this work, this is addressed by employing an amphiphilic conjugated polymer PFPA-1 modified ITO coated glass substrate as the ohmic electron-collecting cathode and PEDOT:PSS PH1000 as the hole-collecting anode. For active layers based on different donor polymers, considerably lower reflection and parasitic absorption are found in the ST solar cells as compared to solar cells in the standard geometry with an ITO/PEDOT:PSS anode and a LiF/Al cathode. The ST solar cells have remarkably high internal quantum efficiency at short circuit condition (similar to 90%) and high transmittance (similar to 50%). Hence, efficient ST tandem solar cells with enhanced power conversion efficiency (PCE) compared to a single ST solar cell can be constructed by connecting the stacked two ST sub-cells in parallel. The total loss of photons by reflection, parasitic absorption and transmission in the ST tandem solar cell can be smaller than the loss in a standard solar cell based on the same active materials. We demonstrate this by stacking five separately prepared ST cells on top of each other, to obtain a higher photocurrent than in an optimized standard solar cell.
|
|
