| 1. |
- Lind, Lars, et al.
(författare)
-
Heterogeneous contributions of change in population distribution of body mass index to change in obesity and underweight NCD Risk Factor Collaboration (NCD-RisC)
- 2021
-
Ingår i: eLife. - : eLife Sciences Publications Ltd. - 2050-084X. ; 10
-
Tidskriftsartikel (refereegranskat)abstract
- From 1985 to 2016, the prevalence of underweight decreased, and that of obesity and severe obesity increased, in most regions, with significant variation in the magnitude of these changes across regions. We investigated how much change in mean body mass index (BMI) explains changes in the prevalence of underweight, obesity, and severe obesity in different regions using data from 2896 population-based studies with 187 million participants. Changes in the prevalence of underweight and total obesity, and to a lesser extent severe obesity, are largely driven by shifts in the distribution of BMI, with smaller contributions from changes in the shape of the distribution. In East and Southeast Asia and sub-Saharan Africa, the underweight tail of the BMI distribution was left behind as the distribution shifted. There is a need for policies that address all forms of malnutrition by making healthy foods accessible and affordable, while restricting unhealthy foods through fiscal and regulatory restrictions.
|
|
| 2. |
- Mishra, A, et al.
(författare)
-
Diminishing benefits of urban living for children and adolescents' growth and development
- 2023
-
Ingår i: Nature. - : Springer Science and Business Media LLC. - 1476-4687 .- 0028-0836. ; 615:7954, s. 874-883
-
Tidskriftsartikel (refereegranskat)abstract
- Optimal growth and development in childhood and adolescence is crucial for lifelong health and well-being1–6. Here we used data from 2,325 population-based studies, with measurements of height and weight from 71 million participants, to report the height and body-mass index (BMI) of children and adolescents aged 5–19 years on the basis of rural and urban place of residence in 200 countries and territories from 1990 to 2020. In 1990, children and adolescents residing in cities were taller than their rural counterparts in all but a few high-income countries. By 2020, the urban height advantage became smaller in most countries, and in many high-income western countries it reversed into a small urban-based disadvantage. The exception was for boys in most countries in sub-Saharan Africa and in some countries in Oceania, south Asia and the region of central Asia, Middle East and north Africa. In these countries, successive cohorts of boys from rural places either did not gain height or possibly became shorter, and hence fell further behind their urban peers. The difference between the age-standardized mean BMI of children in urban and rural areas was <1.1 kg m–2 in the vast majority of countries. Within this small range, BMI increased slightly more in cities than in rural areas, except in south Asia, sub-Saharan Africa and some countries in central and eastern Europe. Our results show that in much of the world, the growth and developmental advantages of living in cities have diminished in the twenty-first century, whereas in much of sub-Saharan Africa they have amplified.
|
|
| 3. |
|
|
| 4. |
|
|
| 5. |
|
|
| 6. |
|
|
| 7. |
|
|
| 8. |
- Callen, Michael, et al.
(författare)
-
COVID-19 vaccine acceptance and hesitancy in low- and middle-income countries
- 2021
-
Ingår i: Nature Medicine. - : Springer Nature. - 1546-170X .- 1078-8956. ; 27:8, s. 1385-1394
-
Tidskriftsartikel (refereegranskat)abstract
- Widespread acceptance of COVID-19 vaccines is crucial for achieving sufficient immunization coverage to end the global pandemic, yet few studies have investigated COVID-19 vaccination attitudes in lower-income countries, where large-scale vaccination is just beginning. We analyze COVID-19 vaccine acceptance across 15 survey samples covering 10 low- and middle-income countries (LMICs) in Asia, Africa and South America, Russia (an upper-middle-income country) and the United States, including a total of 44,260 individuals. We find considerably higher willingness to take a COVID-19 vaccine in our LMIC samples (mean 80.3%; median 78%; range 30.1 percentage points) compared with the United States (mean 64.6%) and Russia (mean 30.4%). Vaccine acceptance in LMICs is primarily explained by an interest in personal protection against COVID-19, while concern about side effects is the most common reason for hesitancy. Health workers are the most trusted sources of guidance about COVID-19 vaccines. Evidence from this sample of LMICs suggests that prioritizing vaccine distribution to the Global South should yield high returns in advancing global immunization coverage. Vaccination campaigns should focus on translating the high levels of stated acceptance into actual uptake. Messages highlighting vaccine efficacy and safety, delivered by healthcare workers, could be effective for addressing any remaining hesitancy in the analyzed LMICs. © 2021, The Author(s).
|
|
| 9. |
- Elbadawi, Mohammed, 1987-, et al.
(författare)
-
Pressure-assisted microsyringe 3D printing of oral films based on pullulan and hydroxypropyl methylcellulose
- 2021
-
Ingår i: International Journal of Pharmaceutics. - : Elsevier. - 0378-5173 .- 1873-3476. ; 595
-
Tidskriftsartikel (refereegranskat)abstract
- Oral films (OFs) continue to attract attention as drug delivery systems, particularly for pedatric and geriatric needs. However, immiscibility between different polymers limits the full potential of OFs from being explored. One example is pullulan (PUL), a novel biopolymer which often has to be blended with other polymers to reduce cost and alter its mechanical properties. In this study, the state-of-the-art in fabrication techniques, three-dimensional (3D) printing was used to produce hybrid film structures of PUL and hydroxypropyl methylcellulose (HPMC), which were loaded with caffeine as a model drug. 3D printing was used to control the spatial deposition of films. HPMC was found to increase the mean mechanical properties of PUL films, where the tensile strength, elastic modulus and elongation break increased from 8.9 to 14.5 MPa, 1.17 to 1.56 GPa and from 1.48% to 1.77%, respectively. In addition, the spatial orientation of the hybrid films was also explored to determine which orientation could maximize the mechanical properties of the hybrid films. The results revealed that 3D printing could modify the mechanical properties of PUL whilst circumventing the issues associated with immiscibility.
|
|
