| 1. |
|
|
| 2. |
- Berg, Magnus, et al.
(författare)
-
Förbränning av utsorterade avfallsfraktioner
- 2005
-
Rapport (övrigt vetenskapligt/konstnärligt)abstract
- Projektet har visat på möjligheter och problem vid förbränning av utsorterade avfallsfraktioner bestående av papper, trä och plast i fluidbädd. Denna typ av bränslen kan antingen samförbrännas eller användas som enda bränsle i en avfallspanna. I båda fallen bör gällande gränsvärden för emissioner till luft kunna klaras men man får däremot räkna med ökade drift- och underhållskostnader, främst beroende på ökade problem med påslag och korrosion. Dessa problem är starkt kopplade till bränslets innehåll av oönskade ämnen såsom klor, alkali och vissa andra metaller. Innehållet av dessa ämnen varierar kraftigt mellan olika bränslefraktioner och därmed blir omfattningen av problemen beroende både av inblandningsgrad och av bränslets ursprung. Projektet har även visat att mängden påslag kan minskas genom tillsats av svaveladditiv samtidigt som den kemiska samansättningen i påslagen förändras på ett sådant sätt att även risken för korrosion bör minska.
|
|
| 3. |
- Broström, Markus, 1977-, et al.
(författare)
-
Sulfation of corrosive alkali chlorides by ammonium sulfate in a biomass fired CFB boiler
- 2007
-
Ingår i: Fuel processing technology. - Amsterdam : Elsevier Bv. - 0378-3820 .- 1873-7188. ; 88:11-12, s. 1171-1177
-
Tidskriftsartikel (refereegranskat)abstract
- Biomass and waste derived fuels contain relatively high amounts of alkali and chlorine, but contain very little sulfur. Combustion of such fuels can result in increased deposit formation and superheater corrosion. These problems can be reduced by using a sulfur containing additive, such as ammonium sulfate, which reacts with the alkali chlorides and forms less corrosive sulfates. Ammonium sulfate injection together with a so-called in situ alkali chloride monitor (IACM) is patented and known as "ChlorOut". IACM measures the concentrations of alkali chlorides (mainly KCl in biomass combustion) at superheater temperatures. Tests with and without spraying ammonium sulfate into the flue gases have been performed in a 96MW(th)/25MW(e) circulating fluidized bed (CFB) boiler. The boiler was fired mainly with bark and a chlorine containing waste. KCl concentration was reduced from more than 15 ppm to approximately 2 ppm. during injection of ammonium sulfate. Corrosion probe measurements indicated that both deposit formation and material loss due to corrosion were decreased using the additive. Analysis of the deposits showed significantly higher concentration of sulfur and almost no chlorine in the case with ammonium sulfate. Results from impactor measurements supported that KCl was sulfated to potassium sulfate by the additive. (C) 2007 Elsevier B.V. All rights reserved.
|
|
| 4. |
|
|
| 5. |
- Forsberg, Christer, et al.
(författare)
-
Principle, calibration, and application of the in situ alkali chloride monitor
- 2009
-
Ingår i: Review of Scientific Instruments. - : American Institute of Physics. - 0034-6748 .- 1089-7623. ; 80:2, s. 023104-1-023104-4
-
Tidskriftsartikel (refereegranskat)abstract
- The extended use of biomass for heat and power production has caused increased operational problems with fouling and high-temperature corrosion in boilers. These problems are mainly related to the presence of alkali chlorides (KCl and NaCl) at high concentrations in the flue gas. The In-Situ Alkali Chloride Monitor (IACM) was developed by Vattenfall Research and Development AB for measuring the alkali chloride concentration in hot flue gases (>650 oC). The measurement technique is based on molecular differential absorption spectroscopy in the UV range. Simultaneous measurement of SO2 concentration is also possible. The measuring range is 1-50 ppm for the sum of KCl and NaCl concentrations, and 4-750 ppm for SO2. This paper describes the principle of the IACM as well as its calibration. Furthermore, an example of its application in an industrial boiler is given.
|
|
| 6. |
|
|
| 7. |
|
|
