| 1. |
- Sababi, Majid, et al.
(författare)
-
Influence of polyaniline and ceria nanoparticle additives on corrosion protection of a UV-cure coating on carbon steel
- 2014
-
Ingår i: Corrosion Science. - : Elsevier BV. - 0010-938X .- 1879-0496. ; 84, s. 189-197
-
Tidskriftsartikel (refereegranskat)abstract
- Influence of a few percents additives of polyaniline doped with phosphoric acid (PAni-PA) and ceria nanoparticle on corrosion protection of a new ultraviolet (UV)-cure polyester acrylate coating have been studied for coil coating on carbon steel by electrochemical measurements during exposure to a NaCl solution. The results demonstrate that the presence of ceria nanoparticles improves the barrier property and stability of the coating. Adding the PAni-PA results in active corrosion protection for carbon steel due to passivation of the steel, and the combination of both additives greatly enhances the protection property over that of the coating matrix alone.
|
|
| 2. |
- Claesson, Per M., et al.
(författare)
-
Bottle-brush polymers : Adsorption at surfaces and interactions with surfactants
- 2010
-
Ingår i: Advances in Colloid and Interface Science. - : Elsevier BV. - 0001-8686 .- 1873-3727. ; 155:1-2, s. 50-57
-
Tidskriftsartikel (refereegranskat)abstract
- Solution and adsorption properties of both charged and uncharged bottle-brush polymers have been investigated. The solution conformation and interactions in solution have been investigated by small-angle scattering techniques. The association of the bottle-brush polymers with anionic surfactants has also been studied. Surfactant binding isotherm measurements, NMR, surface tension measurements, as well as SAXS, SANS and light scattering techniques were utilized for understanding the association behaviour in bulk solutions. The adsorption of the bottle-brush polymers onto oppositely charged surfaces has been explored using a battery of techniques, including reflectometry, ellipsometry, quartz crystal microbalance, and neutron reflectivity. The combination of these techniques allowed determination of adsorbed mass, layer thickness, water content, and structural changes occurring during layer formation. The adsorption onto mica was found to be very different to that on silica, and an explanation for this was sought by employing a lattice mean-field theory. The model was able to reproduce a number of salient experimental features characterizing the adsorption of the bottle-brush polymers over a wide range of compositions, spanning from uncharged bottle-brushes to linear polyelectrolytes. This allowed us to shed light on the importance of electrostatic surface properties and non-electrostatic surface-polymer affinity for the adsorption. The interactions between bottle-brush polymers and anionic surfactants in adsorbed layers have also been elucidated using ellipsometry, neutron reflectivity and surface force measurements.
|
|
| 3. |
- Jafarzadeh, Shadi, et al.
(författare)
-
Nanoscale Electrical and Mechanical Characteristics of Conductive Polyaniline Network in Polymer Composite Films
- 2014
-
Ingår i: ACS Applied Materials and Interfaces. - : American Chemical Society (ACS). - 1944-8244 .- 1944-8252. ; 6:21, s. 19168-19175
-
Tidskriftsartikel (refereegranskat)abstract
- The presence and characteristics of a connected network of polyaniline (PANI) within a composite coating based on polyester acrylate (PEA) has been investigated. The bulk electrical conductivity of the composite was measured by impedance spectroscopy. It was found that the composite films containing PANI have an electrical conductivity level in the range of semiconductors (order of 10–3 S cm–1), which suggests the presence of a connected network of the conductive phase. The nanoscopic distribution of such a network within the cured film was characterized by PeakForce tunneling atomic force microscopy (AFM). This method simultaneously provides local information about surface topography and nanomechanical properties, together with electrical conductivity arising from conductive paths connecting the metallic substrate to the surface of the coating. The data demonstrates that a PEA-rich layer exists at the composite–air interface, which hinders the conductive phase to be fully detected at the surface layer. However, by exposing the internal structure of the composites using a microtome, a much higher population of a conductive network of PANI, with higher elastic modulus than the PEA matrix, was observed and characterized. Local current–voltage (I–V) spectroscopy was utilized to investigate the conduction mechanism within the nanocomposite films, and revealed non-Ohmic characteristics of the conductive network.
|
|
| 4. |
- Jafarzadeh, Shadi, et al.
(författare)
-
Toward Homogeneous Nanostructured Polyaniline/Resin Blends
- 2011
-
Ingår i: ACS Applied Materials & Interfaces. - : American Chemical Society (ACS). - 1944-8244 .- 1944-8252. ; 3:5, s. 1681-1691
-
Tidskriftsartikel (refereegranskat)abstract
- The high interest in applications of conducting polymers, especially polyaniline (PANI), makes it important to overcome limitations for effective usage due to poor processability and solubility. One promising approach is to make blends of PANT in polymeric resins. However, in this approach other problems related to the difficulty of achieving a homogeneous PANI dispersion arise. The present article is focused on this general problem, and we discuss how the synthesis method, choice of dopant and solvent as well as interfacial energies influence the dispersibility. For this purpose, different synthesis methods and dopants have been employed to prepare nanostructures of polyaniline. Dynamic light scattering analysis of dispersions of the synthesized particles in several solvents was employed in order to understand how the choice of solvent affects PANT aggregation. Further information on this subject was achieved by scanning electron microscopy studies of PANT powders dried from various solutions. On the basis of these results, acetone was found to be a suitable dispersion medium for PANI. The polymer matrix used to make the blends in this work is a UV-curing solvent-free resin. Therefore, there is no low molecular weight liquid in the system to facilitate the mixing process and promote formation of homogeneous dispersions. Thus, a good compatibility of the components becomes crucial. For this reason, surface tension and contact angle measurements were utilized for characterizing the surface energy of the PANI particles and the polyester acrylate (PEA) resin, and also for calculating the interfacial energy between these two components that revealed good compatibility within the PANI/PEA blend. A novel technique, based on centrifugal sedimentation analysis, was employed in order to determine the PANT particle size in PEA resin, and high dispersion stability of the PANI/PEA blends was suggested by evaluation of the sedimentation data.
|
|
| 5. |
- Linse, Per, et al.
(författare)
-
Modeling of Bottle-Brush Polymer Adsorption onto Mica and Silica Surfaces : Effect of Side-Chain Length
- 2010
-
Ingår i: Macromolecules. - : American Chemical Society (ACS). - 0024-9297 .- 1520-5835. ; 43:4, s. 2076-2083
-
Tidskriftsartikel (refereegranskat)abstract
- Adsorption of a series of charged bottle-brush polymers with side chains of different length on solid surfaces is modeled using a lattice mean-field theory. The bottle-brush polymers are modeled Lis being composed of two types of main-chain segments: charged segments and uncharged segments with ill attached side chain. The composition variable X denotes the percentage of charged main-chain segments and ranges from X = 0 (uncharged bottle-brush polymer) to X = 100 (linear polyelectrolyte). Two types of surfaces are considered: mica-like and silica-like. The mica-like surface possesses a constant negative surface charge density and no nonelectrostatic affinity for either main-chain or side-chain segments, whereas the silica-like Surface has a constant negative surface potential and a positive affinity for the side chains of the bottle-brush polymers. With the mica-like Surface. ill low X the surface excess becomes smaller and at X >= 25 it becomes larger with increasing side-chain length. Hence, the value of X at which the surface excess displays a maximum increases with the side-chain length. However, with the silica-like Surface the surface excess increases with increasing side-chain length at all X < 100, and the maximum of the surface excess appears at X approximate to 10 independent of the side-chain length.
|
|
| 6. |
- Shovsky, Alexander, et al.
(författare)
-
Cationic poly(N -isopropylacrylamide) block copolymer adsorption investigated by dual polarization interferometry and lattice mean-field theory
- 2012
-
Ingår i: Langmuir. - : American Chemical Society (ACS). - 0743-7463 .- 1520-5827. ; 28:39, s. 14028-14038
-
Tidskriftsartikel (refereegranskat)abstract
- A series of cationic diblock copolymers, poly(N-isopropylacrylamide) 48-block-poly((3-acrylamidopropyl)trimethylammonium chloride) X, abbreviated as PNIPAAM48-b-PAMPTMA+ X (X = 0, 6, 10, 14, and 20), has been synthesized, and their adsorption onto silicon oxynitride from aqueous solution has been investigated using dual polarization interferometry. The polymer adsorption was modeled by using a lattice mean-field theory, and a satisfactory consistency between theory and experiments was found in terms of surface excess and layer thickness. Both theory and experiments show that the adsorption is limited by steric repulsion for X < Xmax and by electrostatic interactions for X > X max. Modeling demonstrates that significant surface charge regulation occurs due to adsorption. Both the nonionic and cationic block exhibit nonelectrostatic affinity to silicon oxynitride and thus contribute to the driving force for adsorption, and modeling is used for clarifying how changes in the nonelectrostatic affinity affects the surface excess. The segments of the nonionic and cationic blocks seem less segregated when both have a nonelectrostatic affinity for the surface compared to the case where the segments had no surface affinity. Adsorption kinetics was investigated experimentally. Two kinetic regimes were observed: the adsorption rate is initially controlled by the mass transfer rate to the surface and at higher coverage is limited by the attachment rate.
|
|
| 7. |
- Acciaro, Roberta, et al.
(författare)
-
Investigation of the formation, structure and release characteristics of self-assembled composite films of cellulose nanofibrils and temperature responsive microgels
- 2011
-
Ingår i: Soft Matter. - : Royal Society of Chemistry (RSC). - 1744-683X .- 1744-6848. ; 7:4, s. 1369-1377
-
Tidskriftsartikel (refereegranskat)abstract
- The possibility of forming self-organized films using charge-stabilized dispersions of cellulose I nanofibrils and microgel beads of poly-(N-isopropylacrylamide-co-acrylic acid) copolymer is presented. The build-up behavior and the properties of the layer-by-layer (LbL)-constructed films were studied using quartz crystal microbalance with dissipation (QCM-D) and ellipsometry. The morphology of the formed films was also characterized using atomic force microscopy (AFM) imaging. The applied methods clearly demonstrated the successful LbL-assembly of the monodisperse microgels and nanofibrils. The in situ QCM-D measurements also revealed that contrary to the polyelectrolyte bound microgel particles, the nanofibrils-bound gel beads preserve their highly swollen state and do not suffer a partial collapse due to the lack of interdigitation of the oppositely charged components. To probe the accessibility of the gel beads in the formed films, the room temperature (similar to 25 degrees C) loading and release of a fluorescent dye (FITC) was also investigated. The incorporation of the cellulose nanofibrils into the multilayer resulted in an open structure that was found easily penetrable for the dye molecules even at constant room temperature, which is in sharp contrast with previously reported systems based on synthetic polyelectrolytes. The amount of dye released from the multilayer films could be fine-tuned with the number of bilayers. Finally, the thermoresponsivity of the films was also shown by triggering the burst release of the loaded dye when the film was collapsed.
|
|
| 8. |
- Alexander, Shovsky, 1978-
(författare)
-
Polyelectrolyte complexes of bottle brush copolymers : Solution and adsorption properties
- 2011
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- The aim of this thesis work was to systematically investigate the physico-chemical properties of polyelectrolyte complexes (PECs) formed by bottle brush and linear polyelectrolytes in solution and at solid / liquid interfaces. Electrostatic self-assembly of oppositely charged macromolecules in aqueous solution is a versatile strategy to construction of functional nanostructures with easily controlled properties. Bottle brush architecture, introduced into the PEC, generates a number of distinctive properties of the complexes, related to a broad range of application, such as colloidal stability and protein repellency to name a few. To utilize these materials in a wide range of applications e.g. drug delivery, the understanding of the effects of polymer architecture and solution parameters on the properties of bottle brush PECs is of paramount importance. This thesis constitutes a systematic investigation of PECs formed by a series of cationic bottle-brush polyelectrolytes and a series of anionic linear polyelectrolytes in aqueous solution. The focus of the first part of the thesis was primarily on formation and characterization of PECs in solution, whereas the adsorption properties and adsorption kinetics of bottle-brush polyelectrolytes and their complexes was investigated in the second part of the thesis work. In particular, effects of the side-chain density of the bottlebrush polyelectrolyte, concentration, mixing ratio and molecular weigh of the linearpolyelectrolyte on formation, solution properties, stability and adsorption of PECs were addressed. The pronounced effect of the side-chain density of the bottle-brush polyelectrolyte on the properties of stoichiometric and nonstoichiometric PECs was demonstrated. Formation of PECs by bottle-brush copolymers with high density of side-chains results in small, watersoluble, molecular complexes having nonspherical shape, independent of concentration. Whereas formation of PEC-aggregates was revealed by bottle-brush polyelectrolytes with low side chain density, the level of aggregation in these complexes is controlled by polyelectrolyte concentration. The structure of the PECs formed with low molecular weight polyanions is consistent with the picture that several small linear polyelectrolyte molecules associate with the large bottle-brush. In contrast, when complexation occurs between polyanions of high molecular weigh and the bottle-brush polymers considerably larger PECs are formed, consistent with several bottle-brush polymers associating with one high molecular weight polyanion.
|
|
| 9. |
- An, Junxue, et al.
(författare)
-
Comparison of a Brush-with-Anchor and a Train-of-Brushes Mucin on Poly(methyl methacrylate) Surfaces : Adsorption, Surface Forces, and Friction
- 2014
-
Ingår i: Biomacromolecules. - : American Chemical Society (ACS). - 1525-7797 .- 1526-4602. ; 15:4, s. 1515-1525
-
Tidskriftsartikel (refereegranskat)abstract
- Interfacial properties of two types of mucins have been investigated at the aqueous solution/poly(methyl methacrylate) (PMMA) interface. One is commercially available bovine submaxillary mucin, BSM, which consists of alternating glycosylated and nonglycosylated regions. The other one is a recombinant mucin-type fusion protein, PSGL-1/mIgG(2b), consisting of a glycosylated mucin part fused to the Fc part of an immunoglobulin. PSGL-1/mIgG(2b) is mainly expressed as a (timer upon production. A quartz crystal microbalance with dissipation was used to study the adsorption of the mucins to PMMA surfaces. The mass of the adsorbed mucin layers, including the adsorbed mucin and water trapped in the layer, was found to be significantly higher for PSGL-1/mIgG(2b) than for BSM. Atomic force microscopy with colloidal probe was employed to study interactions and frictional forces between mucin-coated PMMA surfaces. Purely repulsive forces of steric origin were Observed between PSGL-1/mIgG(2b) mucin layers, whereas a small adhesion was detected between BSM layers and attributed to bridging. Both mucin layers reduced the friction force between PMMA surfaces in aqueous solution. The reduction was, however, significantly more pronounced for PSGL-1/mIgG(2b). The effective friction coefficient between PSGL-1/mIgG(2b)-coated PMMA surfaces is as low as 0.02 at low loads, increasing to 0.24 at the highest load explored, 50 nN. In contrast, a friction coefficient of around 0.7 was obtained between BSM-coated PMMA surfaces. The large differences in interfacial properties for the two mucins are discussed in relation to their structural differences.
|
|
| 10. |
- An, Junxue, et al.
(författare)
-
Temperature-Dependent Adsorption and Adsorption Hysteresis of a Thermoresponsive Diblock Copolymer
- 2014
-
Ingår i: Langmuir. - : American Chemical Society (ACS). - 0743-7463 .- 1520-5827. ; 30:15, s. 4333-4341
-
Tidskriftsartikel (refereegranskat)abstract
- A nonionic-cationic diblock copolymer, poly(2-isopropyl-2-oxazoline)(60)-b-poly((3-acrylamidopropyl)- trimethylammonium chloride)(17), (PIPOZ(60)-b-PAMPTMA(17)), was utilized to electrostatically tether temperature-responsive PIPOZ chains to silica surfaces by physisorption. The effects of polymer concentration, pH, and temperature on adsorption were investigated using quartz crystal microbalance with dissipation monitoring and ellipsometry. The combination of these two techniques allows thorough characterization of the adsorbed layer in terms of surface excess, thickness, and water content. The high affinity of the cationic PAMPTMA(17) block to the negatively charged silica surface gives rise to a high affinity adsorption isotherm, leading to (nearly) irreversible adsorption with respect to dilution. An increase in solution pH lowers the affinity of PIPOZ to silica but enhances the adsorption of the cationic block due to increasing silica surface charge density, which leads to higher adsorption of the cationic diblock copolymer. Higher surface excess is also achieved at higher temperatures due to the worsening of the solvent quality of water for the PIPOZ block. Interestingly, a large hysteresis in adsorbed mass and other layer properties was observed when the temperature was cycled from 25 to 45 degrees C and then back to 25 degrees C. Possible causes for this temperature hysteresis are discussed.
|
|
