| 1. |
- Enarsson, Lars-Erik, et al.
(författare)
-
Polyelectrolyte Adsorption on Thin Cellulose Films Studied with Reflectometry and Quartz Crystal Microgravimetry with Dissipation
- 2009
-
Ingår i: Biomacromolecules. - : American Chemical Society (ACS). - 1525-7797 .- 1526-4602. ; 10:1, s. 134-141
-
Tidskriftsartikel (refereegranskat)abstract
- Thin cellulose films were prepared by dissolving carboxymethylated cellulose fibers in N-methyl morpholine oxide and forming thin films on silicon wafers by spin-coating. The adsorption of cationic polyacrylamides and polydiallyldimethylammonium chloride onto these films was studied by stagnation point adsorption reflectometry (SPAR) and by quartz crystal microgravimetry with dissipation (QCM-D). The polyelectrolyte adsorption was studied by SPAR as a function of salt concentration, and it was found that the adsorption maximum was located at 1 mM NaCl for polyelectrolytes of low charge density and at 10 mM NaCl for polyelectrolytes of high charge density. Electrostatic screening led to complete elimination of the polyelectrolyte adsorption at salt concentrations of 300 mM NaCl. According to the QCM-D analysis, the cellulose films showed a pronounced swelling in water that took several hours to complete. Subsequent adsorption of polyelectrolytes onto the cellulose films led to a release of water from the cellulose, an effect that was substantial for polyelectrolytes of high charge density at low salt concentrations. The total mass change including water could therefore show either an increase or a decrease during adsorption onto the cellulose films, depending on the experimental conditions.
|
|
| 2. |
- Enarsson, Lars-Erik, et al.
(författare)
-
Tailoring the chemistry of polyelectrolytes to control their adsorption on cellulosic surfaces
- 2009
-
Ingår i: Colloids and Surfaces A. - : Elsevier BV. - 0927-7757 .- 1873-4359. ; 340:1-3, s. 135-142
-
Tidskriftsartikel (refereegranskat)abstract
- The adsorption of two types of cationic polyacrylamides in the presence of a background electrolyte was studied on substrates including silicon oxide, kraft pulp fibres and thin films of regenerated cellulose. One of the polyelectrolytes was a conventional cationic polyacrylamide (MeCPAM) and the other was a benzyl-containing derivative of cationic polyacrylamide (BzCPAM). It was found that the aromatic substituents of BzCPAM strongly enhanced the adsorption on substrates of hydrophobically modified silicon oxide when a background electrolyte was present. A similar effect was also seen in the case of BzCPAM adsorption on unbleached pulp fibres, but in this case MeCPAM also exhibited a strong adsorption at high background electrolyte concentrations. On bleached pulp fibres, BzCPAM maintained a high adsorption up to a concentration of 100 mM NaCl whereas MeCPAM adsorption showed a significant decrease at this salt concentration. On model cellulose films, the adsorption of BzCPAM was similar to that of MeCPAM and the non-ionic interactions with cellulose appeared weak, since there was no adsorption of either polyelectrolyte in 300 mM NaCl.
|
|
| 3. |
- Westman, Eva-Helena, et al.
(författare)
-
Assessment of Antibacterial Properties of Polyvinylamine (PVAm) with Different Charge Densities and Hydrophobic Modifications
- 2009
-
Ingår i: Biomacromolecules. - : American Chemical Society (ACS). - 1525-7797 .- 1526-4602. ; 10:6, s. 1478-1483
-
Tidskriftsartikel (refereegranskat)abstract
- Hydrophobically modified and unmodified polyvinylamines (PVAm), including a total of five polymers, were tested against both gram-negative (Escherichia coli) and gram-positive (Bacillus subtilis) bacteria for antimicrobial activity. The assessment of PVAm in solution against bacteria is described, and the influence of the charge density and of the hydrophobic modification of the polyelectrolyte is discussed. The antimicrobial activity was found to depend upon the concentration of PVAm and also on the type of bacteria used. The results also indicated that no direct relationship exists between antimicrobial activity and charge density of the different PVAms. It was, however, observed that an alkyl chain length of six or eight alkane units had a substantial effect on the bacteria investigated. The best combined antibacterial activity for the two bacteria tested was achieved for PVAm with a C-6 alkane substituent (PVAm C-6). To evaluate the antimicrobial activity on a solid substrate, PVAm C-6 was further studied after being deposited onto a glass slide and the results show a large reduction in bacterial infection.
|
|
