| 1. |
- Coad, J. P., et al.
(författare)
-
Diagnostics for studying deposition and erosion processes in JET
- 2005
-
Ingår i: Fusion engineering and design. - : Elsevier. - 0920-3796 .- 1873-7196. ; 74:1-4, s. 745-749
-
Tidskriftsartikel (refereegranskat)abstract
- Estimates of erosion, deposition and H-isotope retention in JET from previous divertor campaigns have relied on analysis of in-vessel components removed at shutdowns. The components analysed have also provided an incomplete coverage of the vessel. In 2004, new diagnostics are being installed to give a more complete picture (such as smart tiles) and to provide some time resolution. The latter includes further quartz microbalances (QMB), following the successful operation of a prototype in 2002-2004 [H.-G. Esser, G. Neill, P. Coad, G.F. Matthews, D. Jolovic, D. Wilson, M. Freisinger, V. Philipps, Quartz microbalance: a time-resolved diagnostic to measure material deposition in JET, Fusion Eng. Des. 66-68 (2003) 855-860; H.-G. Esser, V. Philipps, M. Freisinger, G.F. Matthews, J.P. Coad, G.F. Neill, JET EFDA Contributors, Effect of plasma configuration on carbon migration measured in the inner divertor of JET using quartz microbalance, J. Nucl. Mater. 337-339 (2005) 84-87], which will also have temperature control. Other diagnostics include rotating collectors and deposition monitors [M. Mayer, V. Rohde, P. Coad, P. Wienhold, ASDEX Upgrade Team, JET EFDA Contributors, Carbon erosion and migration in fusion devices, Phys. Scr. T111 (2004) 55-59]. Units are also being installed to provide information on mirrors for ITER.
|
|
| 2. |
- Krieger, K., et al.
(författare)
-
Be wall sources and migration in L-mode discharges after Be evaporation in the JET tokamak
- 2009
-
Ingår i: Journal of Nuclear Materials. - : Elsevier BV. - 0022-3115 .- 1873-4820. ; 390-91, s. 110-114
-
Tidskriftsartikel (refereegranskat)abstract
- First wall material erosion and migration after fresh Be evaporation in the JET tokamak were studied in a series of consecutive identical L-mode discharges. The evolution of Be and C wall and divertor sources towards steady state conditions after deposition of a finite amount of Be at the carbon first wall of JET by the beryllium evaporation procedure provides a data set for benchmarking impurity transport simulations. Furthermore the experiment serves as a reference case for comparison of Be erosion to that of the planned ITER-like wall experiment with mainly Be plasma facing components (PFCs) in the main chamber. The experimental results confirm the migration pattern obtained by campaign integrated accounting of impurity sources and sinks, which is characterised by the main chamber wall and outer divertor as erosion dominated zones and migration of eroded material predominantly to the inner divertor where the material is finally deposited at the target plates.
|
|
| 3. |
- Liang, Y., et al.
(författare)
-
Active control of type-I edge localized modes on JET
- 2007
-
Ingår i: Plasma Physics and Controlled Fusion. - 0741-3335 .- 1361-6587. ; 49:12B, s. B581-B589
-
Tidskriftsartikel (refereegranskat)abstract
- The operational domain for active control of type-I edge localized modes (ELMs) with an n = 1 external magnetic perturbation field induced by the ex-vessel error field correction coils on JET has been developed towards more ITER-relevant regimes with high plasma triangularity, up to 0.45, high normalized beta, up to 3.0, plasma current up to 2.0 MA and q(95) varied between 3.0 and 4.8. The results of ELM mitigation in high triangularity plasmas show that the frequency of type-I ELMs increased by a factor of 4 during the application of the n = 1 fields, while the energy loss per ELM, Delta W/W, decreased from 6% to below the noise level of the diamagnetic measurement (<2%). No reduction of confinement quality (H98Y) during the ELM mitigation phase has been observed. The minimum n = 1 perturbation field amplitude above which the ELMs were mitigated increased with a lower q(95) but always remained below the n = 1 locked mode threshold. The first results of ELM mitigation with n = 2 magnetic perturbations on JET demonstrate that the frequency of ELMs increased from 10 to 35 Hz and a wide operational window of q95 from 4.5 to 3.1 has been found.
|
|
| 4. |
- Murari, A., et al.
(författare)
-
New diagnostic techniques and technologies at JET (invited)
- 2006
-
Ingår i: Review of Scientific Instruments. - : AIP Publishing. - 0034-6748 .- 1089-7623. ; 77:10
-
Tidskriftsartikel (refereegranskat)abstract
- The European Fusion Development Agreement's mission for JET is the development of ITER scenarios exploiting the specific properties of the device. This task requires significant improvements in the measuring techniques. The most innovative diagnostic upgrades are in the fields of edge measurements, detection of fast magnetohydrodynamics modes and burning plasma diagnostics. The importance of plasma-wall interactions, and, in particular, the issue of tritium inventory promoted the development of the quartz microbalance, a detector with improved time resolution to measure material redeposition in the remote areas of the inner divertor. Measurement of Alfven cascades with unprecedented spectral resolution, reaching a toroidal n number of up to 16, was obtained using an O-mode microwave reflectometer as an interferometer. For the diagnosis of the fusion products, a new approach is being developed to measure the He ash based on double charge exchange between thermalized particles and neutrals from JET beams. There have been several upgrades of the neutron diagnostic systems, one of which, the new time of flight neutron spectrometer designed for high counting rates is described.
|
|
| 5. |
|
|
| 6. |
- Strachan, J. D., et al.
(författare)
-
Modelling of carbon migration during JET C-13 injection experiments
- 2008
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 0029-5515 .- 1741-4326. ; 48:10
-
Tidskriftsartikel (refereegranskat)abstract
- JET has performed two dedicated carbon migration experiments on the final run day of separate campaigns ( 2001 and 2004) using (CH4)-C-13 methane injected into repeated discharges. The EDGE2D/NIMBUS code modelled the carbon migration in both experiments. This paper describes this modelling and identifies a number of important migration pathways: ( 1) deposition and erosion near the injection location, ( 2) migration through the main chamber SOL, (3) migration through the private flux region (PFR) aided by E x B drifts and ( 4) neutral migration originating near the strike points. In H-Mode, type I ELMs are calculated to influence the migration by enhancing erosion during the ELM peak and increasing the long-range migration immediately following the ELM. The erosion/re-deposition cycle along the outer target leads to a multistep migration of C-13 towards the separatrix which is called 'walking'. This walking created carbon neutrals at the outer strike point and led to 13C deposition in the PFR. Although several migration pathways have been identified, quantitative analyses are hindered by experimental uncertainty in divertor leakage, and the lack of measurements at locations such as gaps and shadowed regions.
|
|
