| 1. |
|
|
| 2. |
|
|
| 3. |
|
|
| 4. |
|
|
| 5. |
- Fenstermacher, M.E., et al.
(författare)
-
DIII-D research advancing the physics basis for optimizing the tokamak approach to fusion energy
- 2022
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 0029-5515 .- 1741-4326. ; 62:4
-
Tidskriftsartikel (refereegranskat)abstract
- DIII-D physics research addresses critical challenges for the operation of ITER and the next generation of fusion energy devices. This is done through a focus on innovations to provide solutions for high performance long pulse operation, coupled with fundamental plasma physics understanding and model validation, to drive scenario development by integrating high performance core and boundary plasmas. Substantial increases in off-axis current drive efficiency from an innovative top launch system for EC power, and in pressure broadening for Alfven eigenmode control from a co-/counter-I p steerable off-axis neutral beam, all improve the prospects for optimization of future long pulse/steady state high performance tokamak operation. Fundamental studies into the modes that drive the evolution of the pedestal pressure profile and electron vs ion heat flux validate predictive models of pedestal recovery after ELMs. Understanding the physics mechanisms of ELM control and density pumpout by 3D magnetic perturbation fields leads to confident predictions for ITER and future devices. Validated modeling of high-Z shattered pellet injection for disruption mitigation, runaway electron dissipation, and techniques for disruption prediction and avoidance including machine learning, give confidence in handling disruptivity for future devices. For the non-nuclear phase of ITER, two actuators are identified to lower the L-H threshold power in hydrogen plasmas. With this physics understanding and suite of capabilities, a high poloidal beta optimized-core scenario with an internal transport barrier that projects nearly to Q = 10 in ITER at ∼8 MA was coupled to a detached divertor, and a near super H-mode optimized-pedestal scenario with co-I p beam injection was coupled to a radiative divertor. The hybrid core scenario was achieved directly, without the need for anomalous current diffusion, using off-axis current drive actuators. Also, a controller to assess proximity to stability limits and regulate β N in the ITER baseline scenario, based on plasma response to probing 3D fields, was demonstrated. Finally, innovative tokamak operation using a negative triangularity shape showed many attractive features for future pilot plant operation.
|
|
| 6. |
- Hobirk, J., et al.
(författare)
-
The JET hybrid scenario in Deuterium, Tritium and Deuterium-Tritium
- 2023
-
Ingår i: Nuclear Fusion. - : Institute of Physics Publishing (IOPP). - 0029-5515 .- 1741-4326. ; 63:11
-
Tidskriftsartikel (refereegranskat)abstract
- The JET hybrid scenario has been developed from low plasma current carbon wall discharges to the record-breaking Deuterium-Tritium plasmas obtained in 2021 with the ITER-like Be/W wall. The development started in pure Deuterium with refinement of the plasma current, and toroidal magnetic field choices and succeeded in solving the heat load challenges arising from 37 MW of injected power in the ITER like wall environment, keeping the radiation in the edge and core controlled, avoiding MHD instabilities and reaching high neutron rates. The Deuterium hybrid plasmas have been re-run in Tritium and methods have been found to keep the radiation controlled but not at high fusion performance probably due to time constraints. For the first time this scenario has been run in Deuterium-Tritium (50:50). These plasmas were re-optimised to have a radiation-stable H-mode entry phase, good impurity control through edge Ti gradient screening and optimised performance with fusion power exceeding 10 MW for longer than three alpha particle slow down times, 8.3 MW averaged over 5 s and fusion energy of 45.8 MJ.
|
|
| 7. |
- Hatch, D. R., et al.
(författare)
-
Microtearing modes as the source of magnetic fluctuations in the JET pedestal
- 2021
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 0029-5515 .- 1741-4326. ; 61:3
-
Tidskriftsartikel (refereegranskat)abstract
- We report on a detailed study of magnetic fluctuations in the JET pedestal, employing basic theoretical considerations, gyrokinetic simulations, and experimental fluctuation data to establish the physical basis for their origin, role, and distinctive characteristics. We demonstrate quantitative agreement between gyrokinetic simulations of microtearing modes (MTMs) and two magnetic frequency bands with corresponding toroidal mode numbers n = 4 and 8. Such disparate fluctuation scales, with substantial gaps between toroidal mode numbers, are commonly observed in pedestal fluctuations. Here we provide a clear explanation, namely the alignment of the relevant rational surfaces (and not others) with the peak in the omega(*) profile, which is localized in the steep gradient region of the pedestal. We demonstrate that a global treatment is required to capture this effect. Nonlinear simulations suggest that the MTM fluctuations produce experimentally-relevant transport levels and saturate by relaxing the background electron temperature gradient, slightly downshifting the fluctuation frequencies from the linear predictions. Scans in collisionality are compared with a simple MTM dispersion relation. At the experimental points considered, MTM growth rates can either increase or decrease with collision frequency depending on the parameters thus defying any simple characterization of collisionality dependence.
|
|
| 8. |
- Mantsinen, M. J., et al.
(författare)
-
Experiments in high-performance JET plasmas in preparation of second harmonic ICRF heating of tritium in ITER
- 2023
-
Ingår i: Nuclear Fusion. - : Institute of Physics (IOP). - 0029-5515 .- 1741-4326. ; 63:11
-
Tidskriftsartikel (refereegranskat)abstract
- The reference ion cyclotron resonance frequency (ICRF) heating schemes for ITER deuterium-tritium (D-T) plasmas at the full magnetic field of 5.3 T are second harmonic heating of T and 3He minority heating. The wave-particle resonance location for these schemes coincide and are central at a wave frequency of 53 MHz at 5.3 T. Experiments have been carried out in the second major D-T campaign (DTE2) at JET, and in its prior D campaigns, to integrate these ICRF scenarios in JET high-performance plasmas and to compare their performance with the commonly used hydrogen (H) minority heating. In 50:50 D:T plasmas, up to 35% and 5% larger fusion power and diamagnetic energy content, respectively, were obtained with second harmonic heating of T as compared to H minority heating at comparable total input powers and gas injection rates. The core ion temperature was up to 30% and 20% higher with second harmonic T and 3He minority heating, respectively, with respect to H minority heating. These are favourable results for the use of these scenarios in ITER and future fusion reactors. According to modelling, adding ICRF heating to neutral beam injection using D and T beams resulted in a 10%-20% increase of on-axis bulk ion heating in the D-T plasmas due to its localisation in the plasma core. Central power deposition was confirmed with the break-in-slope and fast Fourier transform analysis of ion and electron temperature in response to ICRF modulation. The tail temperature of fast ICRF-accelerated tritons, their enhancement of the fusion yield and time behaviour as measured by an upgraded magnetic proton recoil spectrometer and neutral particle analyser were found in agreement with theoretical predictions. No losses of ICRF-accelerated ions were observed by fast ion detectors, which was as expected given the high plasma density of n e approximate to 7-8 x 1019 m-3 in the main heating phase that limited the formation of ICRF-accelerated fast ion tails. 3He was introduced in the machine by 3He gas injection, and the 3He concentration was measured by a high-resolution optical penning gauge in the sub-divertor region. The DTE2 experiments with 3He minority heating were carried with a low 3He concentration in the range of 2%-4% given the fact that the highest neutron rates with 3He minority heating in D plasmas were obtained at low 3He concentrations of similar to 2%, which also coincided with the highest plasma diamagnetic energy content. In addition to 3He introduced by 3He gas injection, an intrinsic concentration of 3He of the order of 0.2%-0.4% was measured in D-T plasmas before 3He was introduced in the device, which is attributed to the radioactive decay of tritium to 3He. According to modelling, even such low intrinsic concentrations of 3He lead to significant changes in ICRF power partitioning during second harmonic heating of T due to absorption of up to 30% of the wave power by 3He.
|
|
| 9. |
- Horvath, L., et al.
(författare)
-
Isotope dependence of the type I ELMy H-mode pedestal in JET-ILW hydrogen and deuterium plasmas
- 2021
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 0029-5515 .- 1741-4326. ; 61:4
-
Tidskriftsartikel (refereegranskat)abstract
- The pedestal structure, edge transport and linear MHD stability have been analyzed in a series of JET with the ITER-like wall hydrogen (H) and deuterium (D) type I ELMy H-mode plasmas. The pedestal pressure is typically higher in D than in H at the same input power and gas rate, with the difference mainly due to lower density in H than in D (Maggi et al (JET Contributors) 2018 Plasma Phys. Control. Fusion 60 014045). A power balance analysis of the pedestal has shown that higher inter-ELM separatrix loss power is required in H than in D to maintain a similar pedestal top pressure. This is qualitatively consistent with a set of interpretative EDGE2D-EIRENE simulations for H and D plasmas, showing that higher edge particle and heat transport coefficients are needed in H than in D to match the experimental profiles. It has also been concluded that the difference in neutral penetration between H and D leads only to minor changes in the upstream density profiles and with trends opposite to experimental observations. This implies that neutral penetration has a minor role in setting the difference between H and D pedestals, but higher ELM and/or inter-ELM transport are likely to be the main players. The interpretative EDGE2D-EIRENE simulations, with simultaneous upstream and outer divertor target profile constraints, have indicated higher separatrix electron temperature in H than in D for a pair of discharges at low fueling gas rate and similar stored energy (which required higher input power in H than in D at the same gas rate). The isotope dependence of linear MHD pedestal stability has been found to be small, but if a higher separatrix temperature is considered in H than in D, this could lead to destabilization of peeling-ballooning modes and shrinking of the stability boundary, qualitatively consistent with the reduced pedestal confinement in H.
|
|
| 10. |
- Curie, M. T., et al.
(författare)
-
A survey of pedestal magnetic fluctuations using gyrokinetics and a global reduced model for microtearing stability
- 2022
-
Ingår i: Physics of Plasmas. - : AIP Publishing. - 1070-664X .- 1089-7674. ; 29:4, s. 042503-
-
Tidskriftsartikel (refereegranskat)abstract
- This article presents a global reduced model for slab-like microtearing modes (MTMs) in the H-mode pedestal, which reproduces distinctive features of experimentally observed magnetic fluctuations, such as chirping and discrete frequency bands at noncontiguous mode numbers. Our model, importantly, includes the global variation of the diamagnetic frequencies, which is necessary to reproduce the experimental observations. The key insight underlying this model is that MTM instability is enabled by the alignment of a rational surface with the peak in the profile of the diamagnetic frequency. Conversely, MTMs are strongly stabilized for toroidal mode numbers for which these quantities are misaligned. This property explains the discrete fluctuation bands in several DIII-D and JET discharges, which we survey using our reduced model in conjunction with global gyrokinetic simulations. A fast yet accurate reduced model for MTMs enables rapid interpretation of magnetic fluctuation data from a wide range of experimental conditions to help assess the role of MTM in the pedestal.
|
|
