| 1. |
- Hermann, D. S., et al.
(författare)
-
Novel passive polymer waveguides integrated with electro-optically active ferroelectric liquid crystals
- 2001
-
Ingår i: Optical Engineering. - : SPIE-Intl Soc Optical Eng. - 0091-3286 .- 1560-2303. ; 40:10, s. 2188-2198
-
Tidskriftsartikel (refereegranskat)abstract
- We report the preparation and characterization of novel isotropic polymer slab waveguides made by photochemical crosslinking, and their integration with a ferroelectric liquid crystal in an integrated electro-optic modulator. The refractive index of the passive copolymer material in the device was controlled by the copolymer composition, and good agreement between measured and calculated effective indices for the guided modes of polymer films was obtained. The active ferroelectric liquid crystal exhibited a refractive index change of Deltan approximate to0.10 upon application of an ac voltage of +/- 30 V, giving an electro-optic modulation of the input TE0-mode with a contrast ratio of 11:1 and only a small polarization conversion into TM output light.
|
|
| 2. |
- Johansson, Mats K. G., et al.
(författare)
-
Radiation curing of hyperbranched polyester resins
- 2000
-
Ingår i: Journal of Applied Polymer Science. - 0021-8995 .- 1097-4628. ; 75:5, s. 612-618
-
Tidskriftsartikel (refereegranskat)abstract
- A research area that has obtained increasing interest during the last decade concerns improvement of macromolecular properties by changes in the macromolecular architecture. One group of these materials is dendritic polymers, which are highly branched structures exhibiting very different properties compared with linear polymers. One potential application for these polymers is as radiation curable thermoset resins. This article describes a study where the use of an aliphatic hyperbranched polyester as a base for new radiation curable thermoset resins. The hyperbranched polyesters have been characterized with respect to cure rate and final mechanical properties compared with conventional resins. It is shown that hyperbranched polyesters can be used as versatile scaffolds for various radiation curable resin structures.
|
|
| 3. |
- Krupicka, A., et al.
(författare)
-
Mechanical surface characterization : A promising procedure to screen organic coatings
- 2003
-
Ingår i: JCT. - 0361-8773. ; 75:939, s. 19-
-
Tidskriftsartikel (refereegranskat)abstract
- Two ductile coating materials were subjected to a combined indentation and scratch test procedure designed to screen a predetermined pattern of many small sample surfaces in a limited time. The screening of 50 surface spots ordered in a matrix pattern on the surface was carried out in 4.5 hr. The test provides reproducible data in terms of indentaion modulus, elastic recovery, scratch penetration depth, and scratch residual depth, and also offers the possibility of detecting critical mechanical transitions such as rupture. The presented procedure produces sufficient data in a limited time scale to fulfill the requirements for a fast method to screen coating compositions.
|
|
| 4. |
- Busson, P., et al.
(författare)
-
Ferroelectric liquid crystalline dendrimers : Synthesis, thermal behavior, and electrooptical characterization
- 2001
-
Ingår i: Macromolecules. - : American Chemical Society (ACS). - 0024-9297 .- 1520-5835. ; 34:5, s. 1221-1229
-
Tidskriftsartikel (refereegranskat)abstract
- The preparation and characterization of a series of novel ferroelectric liquid crystalline dendrimers are presented. End-capping of 1-, 2-, and 3-generation dendrimers based on 2,2-bis(hydroxymethyl)propionic acid with mesogens gave surface-functionalized liquid crystalline compounds with 6, 12, and 24 mesogen-containing units, respectively. 4 -((R)-1-Methylheptyloxy)phenyl 4-(4 '-[10(hydroxycarbonyl)decyloxyl phenyl)benzoate was synthesized and used as a mesogen-containing unit. The purity and structure of each compound were determined by H-1 NMR spectroscopy, size exclusion chromatography, and elemental analysis. Differential scanning calorimetry and optical microscopy were used to investigate the mesomorphic properties of the mesogen-functionalized dendrimers. The materials displayed a variety of mesophases, including the smectic C* phase. All the liquid crystalline dendrimers showed ferroelectricity, and tilt angle and spontaneous polarization measurements were performed. The obtained results show that the ferroelectric properties of the materials are independent of the generation number of the dendritic scaffold.
|
|
| 5. |
- Busson, P., et al.
(författare)
-
Preparation of mesogen-functionalized dendrimers for second-order nonlinear optics
- 2002
-
Ingår i: Macromolecules. - : American Chemical Society (ACS). - 0024-9297 .- 1520-5835. ; 35:5, s. 1663-1671
-
Tidskriftsartikel (refereegranskat)abstract
- Liquid crystalline dendrimers with peripheral mesogen-containing units have been prepared. Multistep synthesis with several selective reactions was used in the preparation of the mesogen-containing molecules, 4-[10-(hydroxycarbonyl)decyloxy]phenyl 4-[4'-(2-(R)-octyloxy)-3'-nitrophenyl]benzo ate and 4-[10-(hydroxycarbonyl)decyloxy]biphenyl 4-[4'-(2-(R)-octyloxy)-3'-nitrophenyl]benzoate. Both molecules possessed an electron-accepting nitro group placed perpendicular to the long axis of the molecules in order to enhance the nonlinear optical activity. A second generation hydroxyl functional aliphatic dendrimer based on the dihydroxy acid, 2,2-bis(hydroxymethyl)propionic acid, was used as dendritic scaffold and was subsequently functionalized with the aforementioned groups. The purity and structure of the two liquid crystalline dendrimers were determined by H-1 NMR spectroscopy, size exclusion chromatography, and elemental analysis. The synthesis of both the mesogen-containing units and the liquid crystalline dendrimers is described in detail. Investigation of the liquid crystalline properties of the materials by differential scanning calorimetry and optical microscopy showed that they exhibited different mesophases, including the chiral smectic C phase. Ferroelectric switching was observed in this tilted phase, and electrooptical properties, including tilt angle and spontaneous polarization measurements, were investigated. Finally, the nonlinear optical properties of one of the materials were preliminary characterized.
|
|
| 6. |
- Claesson, Hans, et al.
(författare)
-
Rheological behaviour during UV-curing of a star-branched polyester
- 2002
-
Ingår i: Progress in organic coatings. - 0300-9440 .- 1873-331X. ; 44:1, s. 63-67
-
Tidskriftsartikel (refereegranskat)abstract
- Using a rheometer coupled with an UV-light generator, the viscoelastic behaviour during the fast cure of star-branched polyester is investigated. The 32 arm star polymers consist of a hyperbranched polyester core, Boltorn(TM) and linear grafts of poly(E-caprolactone) (degree of polymerisation: 20-52) with methacrylate end groups. The resins are crystalline and the melting points range from 34 to 50degreesC; films can be formed and cured below 80degreesC. The crossover of G' and G was used as the gel point. The time to reach the gel point, a few seconds, increases linearly with molecular weight.
|
|
| 7. |
- Claesson, Hans, et al.
(författare)
-
Semi-crystalline thermoset resins : tailoring rheological properties in melt using comb structures with crystalline grafts
- 2004
-
Ingår i: Progress in organic coatings. - : Elsevier BV. - 0300-9440 .- 1873-331X. ; 49:1, s. 13-22
-
Tidskriftsartikel (refereegranskat)abstract
- Thermosetting resins with semi-crystalline grafts have been synthesized. An amorphous resin with epoxide groups was first functionalized with hydroxyl groups using 2,2-bis(methylol) propionic acid, bis-MPA in bulk at 155 degreesC. Functionalization with bis-MPA was monitored using FT-IR, FT-Raman and SEC. The reaction was complete in 30 min. Grafts of poly(epsilon-caprolactone) were then grown from the hydroxyl functional resin and end capped with methacrylate groups. The polymerization Of epsilon-caprolactone, performed in bulk at 110 degreesC using Sn(Oct)(2), was characterized using H-1 NMR and SEC. The obtained molecular weights agreed well with theoretical values. The final end capping was performed using methacrylic anhydride, and monitored with SEC and H-1 NMR, which indicated full substitution. Two combs were synthesized with different arm lengths, DP 10 and 20, and the obtained M-W were close to calculated values. The complex viscosity was measured from low to high temperature for the crystalline resins, the amorphous resin and blends thereof. Rheological data show a rapid decrease in viscosity within a temperature change of 10-15 degreesC for the crystalline resins while the amorphous resin exhibited a slow softening. The blends exhibited a behavior in-between that of the crystalline and the amorphous resin. Films were prepared from the pure resins and the blends. The films were cured using UV irradiation. The comb architecture of these resins has advantages such as crystallinity, high molecular weight and low viscosity, facilitating leveling and resulting in smooth films. The final film properties varied with the ratio of crystalline to amorphous resin, where increase in the amount of crystalline resin correlated with increased the flexibility.
|
|
| 8. |
- Claesson, Hans, et al.
(författare)
-
Synthesis and characterisation of star branched polyesters with dendritic cores and the effect of structural variations on zero shear rate viscosity
- 2002
-
Ingår i: Polymer. - 0032-3861 .- 1873-2291. ; 43:12, s. 3511-3518
-
Tidskriftsartikel (refereegranskat)abstract
- A series of branched polyesters consisting of poly(epsilon-caprolactone) (PCL) (degree of polymerisation: 5-200) initiated from hydroxy-functional cores and end-capped with methylmethacrylate have been prepared. The cores were third-generation hyperbranched polyester, Boltorn, with approximately 32 hydroxyl groups, a third-generation dendrimer with 24 hydroxyl groups and a third-generation dendron with eight hydroxyl groups. Finally, a linear PCL was synthesised as a reference material. All initiators were based on 2,2-bis(methylol) propionic acid (bis-MPA). C-13 NMR spectra of the polymers showed that those with shorter arms contained unreacted hydroxyl groups on the core. Rheological measurements of zero shear rate viscosity, eta(0), showed that the branched polyesters had a considerably lower eta(0) than linear polyester with similar molecular weight. The low melt viscosity and the crystallity produced a theological behaviour suitable for the film formation process for powder coatings. Measurements of mechanical properties of cured films showed that those with low arm molecular weight, M-a, were amorphous while those of high M-a were crystalline.
|
|
| 9. |
- Coullerez, G., et al.
(författare)
-
Cationization of dendritic macromolecule adsorbates on metals studied by time-of-flight secondary ion mass spectrometry
- 2003
-
Ingår i: Surface and Interface Analysis. - : Wiley. - 0142-2421 .- 1096-9918. ; 35:8, s. 682-692
-
Tidskriftsartikel (refereegranskat)abstract
- Time-of-flight secondary ion mass spectrometry (ToF-SIMS) was utilized to study dendritic macromolecules with various architectures, such as dendrons, dendrimers and hyperbranched polyesters prepared from bis-(hydroxymethyl)propionic acid (Bis-MPA) and a series of hyperbranched polyethers based on 3-ethyl-3(hydroxymethyl)oxetane. The measurements were performed on spin-coated thin films of the branched molecules (D) onto silicon, chemically etched copper foil and silver-coated wafers. They showed weak signatures of molecular ions by proton capture (D + H)(+) in the high mass range of the spectra (m/z > 400). On the contrary, cationization of the intact molecules with alkali or transition metal ions such as Na+, Cu+ or Ag+ was observed. High-intensity quasi-molecular ions (D + M)(+) (with M = Na+, Cu+ or Ag+) allowed the studied polymers to be identified. The whole molecular species were observed for Bis-MPA dendrons and dendrimers up to 3000 Da for hydroxyl or acetonide-terminated derivatives. The success of the so-called cationization experiments with metal substrates compared with analysis of molecular adsorbates on silicon is highlighted. The ToF-SIMS sensitivity appeared useful to provide information about the molecular end-groups or to highlight incomplete reaction occurring during some deprotection step of the synthesis. Only uncationized fragments of low masses were detected for the hyperbranched polyesters. This result suggested the effect of molecular asymmetry and/or flattening of the molecules on the substrates, which hampered the molecule lift-off efficiency. Nevertheless, the hyperbranched polyethers were characterized based on the peak distribution of intensities, which allowed estimation of their molecular weight average. This work was intended to illustrate the capabilities of ToF-SIMS to analyse dendritic polymers on surfaces.
|
|
| 10. |
- Coullerez, G., et al.
(författare)
-
Insights into ToF-SIMS analysis of dendritic macromolecules : cationization and PCA to probe their molecular weight on surfaces
- 2003
-
Ingår i: Applied Surface Science. - 0169-4332 .- 1873-5584. ; 203, s. 620-624
-
Tidskriftsartikel (refereegranskat)abstract
- Time-of-flight secondary ion mass spectrometry (ToF-SIMS) is utilized to study dendrons, dendrimers and hyperbranched derivatives prepared from the 2,2-bis(hydroxymethyl)propionic acid (bis-MPA) or the 3-ethyl-3-(hydroxymethyl)oxetane (TMPO). We show that the cationization experiments of the intact molecules with alkali or metal ions such as Na+, Cu+ or Ag+ allow to detect whole molecular species up to 3000 Da (low generation). It allows to probe directly their molecular TM weight and end-functionality. However, when the molecule lift-off fails for series of hyperbranched polyesters Boltorn(TM), the fingerprint part of the SIMS spectra (m/z < 300 Da) is instead used. The low-mass fragments are mainly assigned to the bis-MP repeating unit. Ions due to the core molecule are also distinguished. Data treatment is combined with the principal component analysis (PCA) multivariate statistical method to highlight the main differences between the spectra. Only one principal component (PC1) is needed to describe most of the variance between the samples taking into account the generation effect. PC1 plotted as a function of the molecular weight gives a calibration curve. Normalization of the data set by ion intensities from the core molecule allows the linearization of the SIMS intensities vs. the molecular weight.
|
|
