| 1. |
- Idris, Alamin, et al.
(författare)
-
Oxygen Barrier Performance of Poly (Vinyl Alcohol) Coating Films with Different Induced Crystallinity and Model Predictions
- 2021
-
Ingår i: Coatings. - : MDPI AG. - 2079-6412. ; 11, s. 1-12
-
Tidskriftsartikel (refereegranskat)abstract
- The presence of the crystalline regions in poly(vinyl alcohol) coating films acts as barrier clusters forcing the gas molecules to diffuse in a longer pathway in the amorphous region of the polymer, where diffusivity and solubility are promoted in comparison. Evaluating the influence of crystalline regions on the oxygen barrier property of a semi-crystalline polymer is thus essential to prepare better coating films. Poly(vinyl alcohol) coating films with varying induced crystallinity were prepared on a polyethylene terephthalate (PET) substrate by drying at different annealing temperatures for 10 min. The coating films were first delaminated from the PET substrate and then characterized using Fourier transform infrared (FTIR) spectroscopy, differential scanning calorimetry (DSC), and X-ray diffraction (XRD) techniques to determine and confirm the induced percentage of crystallinity. The barrier performance of the coating films, i.e., the oxygen transmission rate (OTR), was measured at room temperature. Results showed a decrease in the OTR values of poly(vinyl alcohol) film with an increase in the degree of crystallinity of the polymer matrix. Tortuosity-based models, i.e., modified Nielsen models, were adopted to predict the barrier property of the semi-crystalline PVOH film with uniform or randomly distributed crystallites. A modified Nielsen model for orderly distributed crystallites with an aspect ratio of 3.4 and for randomly distributed crystallites with an aspect ratio of 10.4 resulted in a good correlation with the experimental observation. For the randomly distributed crystallites, lower absolute average relative errors of 4.66, 4.45, and 5.79% were observed as compared to orderly distributed crystallites when the degree of crystallinity was obtained using FTIR, DSC, and XRD data, respectively.
|
|
| 2. |
- Iftikhar, Bawar, et al.
(författare)
-
Experimental study on the eco-friendly plastic-sand paver blocks by utilising plastic waste and basalt fibers
- 2023
-
Ingår i: Heliyon. - : Elsevier. - 2405-8440. ; 9:6
-
Tidskriftsartikel (refereegranskat)abstract
- Plastic waste poses a significant hazard to the environment as a result of its high production rates, which endanger both the environment and its inhabitants. Similarly, another concern is the production of cement, which accounts for roughly 8% of global CO2 emissions. Thus, recycling plastic waste as a replacement for cementitious materials may be a more effective strategy for waste minimisation and cement elimination. Therefore, in this study, plastic waste (low-density polyethylene) is utilised in the production of plastic sand paver blocks without the use of cement. In addition to this, basalt fibers which is a green industrial material is also added in the production of eco-friendly plastic sand paver blocks to satisfy the standard of ASTM C902-15 of 20 N/mm2 for the light traffic. In order to make the paver blocks, the LDPE waste plastic was melted outside in the open air and then combined with sand. Variations were made to the ratio of LDPE to sand, the proportion of basalt fibers, and sand particle size. Paver blocks were evaluated for their compressive strength, water absorption, and at different temperatures. Including 0.5% percent basalt fiber of length 4 mm gives us the best result by enhancing compressive strength by 20.5% and decreasing water absorption by 50.5%. The best results were obtained with a ratio of 30:70 LDPE to sand, while the finest sand provides the greatest compressive strength. Moreover, the temperature effect was also studied from 0 to 60 °C, and the basalt fibers incorporated in plastic paver blocks showed only a 20% decrease in compressive strength at 60 °C. This research has produced eco-friendly paver blocks by removing cement and replacing it with plastic waste, which will benefit the environment, save money, reduce carbon dioxide emissions, and be suitable for low-traffic areas, all of which contribute to sustainable development.
|
|
| 3. |
- Javed, Asif, 1982-, et al.
(författare)
-
Lignin-containing coatings for packaging materials—pilot trials
- 2021
-
Ingår i: Polymers. - : MDPI AG. - 2073-4360. ; 13:10
-
Tidskriftsartikel (refereegranskat)abstract
- One severe weakness of most biopolymers, in terms of their use as packaging materials, is their relatively high solubility in water. The addition of kraft lignin to starch coating formulations has been shown to reduce the water solubility of starch in dry coatings. However, lignin may also migrate into aqueous solutions. For this paper, kraft lignin isolated using the LignoBoost process was used in order to examine the effect of pH level on the solubility of lignin with and without ammonium zirconium carbonate (AZC). Machine-glazed (MG) paper was coated in a pilot coating machine, with the moving substrate at high speed, and laboratory-coated samples were used as a reference when measuring defects (number of pinholes). Kraft lignin became soluble in water at lower pH levels when starch was added to the solution, due to the interactions between starch and lignin. This made it possible to lower the pH of the coating solutions, resulting in increased water stability of the dry samples; that is, the migration of lignin to the model liquids decreased when the pH of the coating solutions was reduced. No significant difference was observed in the water vapor transmission rate (WVTR) between high and low pH for the pilot-coated samples. The addition of AZC to the formulation reduced the migration of lignin from the coatings to the model liquids and led to an increase in the water contact angle, but also increased the number of pinholes in the pilot-coated samples. © 2021 by the authors
|
|
| 4. |
- Javed, Sana, et al.
(författare)
-
Biophysics and the nonlinear dynamics instigated by a special hormone
- 2020
-
Ingår i: Progress in Biophysics and Molecular Biology. - : Elsevier BV. - 0079-6107 .- 1873-1732. ; 150, s. 62-66
-
Forskningsöversikt (refereegranskat)abstract
- Calcitonin, a potent hypocalcemic hormone, plays a vital role in inhibiting osteoclastic activities and suppressing bone removal. The physiological characteristics of calcitonin have long been discussed, along a few recommending calcitonin as a vestigial hormone. The basis for this article is to discuss the role of low and high levels of calcitonin in normal and osteoprotic bone turnover. The effect of calcitonin on the receptor activator of nuclear factor kappa-ligand and osteoclasts has been demonstrated using numerical simulations. This behavior recommends that treatment of osteoporosis via calcitonin does not provide the required upshots. For effectiveness calcitonin must be advised along with a combined therapy like aspirin which agrees with the experimental results available in the literature.
|
|
| 5. |
|
|
