| 1. |
- Knaust, Stefan, 1985-, et al.
(författare)
-
Influence of flow rate, temperature and pressure on multiphase flows of supercritical carbon dioxide and water using multivariate partial least square regression
- 2015
-
Ingår i: Journal of Micromechanics and Microengineering. - : Institute of Physics Publishing (IOPP). - 0960-1317 .- 1361-6439. ; 25:10
-
Tidskriftsartikel (refereegranskat)abstract
- Supercritical carbon dioxide (scCO(2)) is often used to replace harmful solvents and can dissolve a wide range of organic compounds. With a favorable critical point at 31 degrees C and 7.4 MPa, reaching above the critical point for scCO(2) is fairly accessible. Because of the compressible nature of scCO(2) and the large changes of viscosity and density with temperature and pressure, there is a need to determine the behavior of scCO(2) in microfluidic systems. Here, the influence of how parameters such as flow rate, temperature, pressure, and flow ratio affects the length of parallel flow of water and scCO(2) and the length of the created CO2 segments are investigated and modeled using multivariate data analysis for a 10 mm long double-y channel. The parallel length and segment size were observed in the laminar regime around and above the critical point of CO2. The flow ratio between the two fluids together with the flow rate influenced both the parallel length and the segment sizes, and a higher pressure resulted in shorter parallel lengths. Regarding the segment length of CO2, longer segments were a result of a higher Weber number for H2O together with a higher temperature in the channel.
|
|
| 2. |
- Knaust, Stefan
(författare)
-
Microsystems for Harsh Environments
- 2015
-
Doktorsavhandling (övrigt vetenskapligt/konstnärligt)abstract
- When operating microsystems in harsh environments, many conventionally used techniques are limiting. Further, depending on if the demands arise from the environment or the conditions inside the system, different approaches have to be used. This thesis deals with the challenges encountered when microsystems are used at high pressures and high temperatures.For microsystems operating at harsh conditions, many parameters will vary extensively with both temperature and pressure, and to maintain control, these variations needs to be well understood. Covered within this thesis is the to-date strongest membrane micropump, demonstrated to pump against back-pressures up to 13 MPa, and a gas-tight high pressure valve that manages pressures beyond 20 MPa.With the ability to manipulate fluids at high pressures in microsystems at elevated temperatures, opportunities are created to use green solvents like supercritical fluids like CO2. To allow for a reliable and predictable operation in systems using more than one fluid, the behavior of the multiphase flow needs to be controlled. Therefore, the effect of varying temperature and pressure, as well as flow conditions were investigated for multiphase flows of CO2 and H2O around and above the critical point of CO2. Also, the influence of channel surface and geometry was investigated.Although supercritical CO2 only requires moderate temperatures, other supercritical fluids or reactions require much higher temperatures. The study how increasing temperature affects a system, a high-temperature testbed inside an electron microscope was created.One of the challenges for high-temperature systems is the interface towards room temperature components. To circumvent the need of wires, high temperature wireless systems were studied together with a wireless pressure sensing system operating at temperatures up to 1,000 °C for pressures up to 0.3 MPa.To further extend the capabilities of microsystems and combine high temperatures and high pressures, it is necessary to consider that the requirements differs fundamentally. Therefore, combining high pressures and high temperatures in microsystems results in great challenges, which requires trade-offs and compromises. Here, steel and HTCC based microsystems may prove interesting alternatives for future high performance microsystems.
|
|
| 3. |
- Sturesson, Peter, et al.
(författare)
-
Thermomechanical properties and performance of ceramic resonators for wireless pressure reading at high temperatures
- 2015
-
Ingår i: Journal of Micromechanics and Microengineering. - Bristol : Institute of Physics Publishing (IOPP). - 0960-1317 .- 1361-6439. ; 25:9
-
Tidskriftsartikel (refereegranskat)abstract
- This paper reports on the design, fabrication, and thermomechanical study of ceramic LC resonators for wireless pressure reading, verified at room temperature, at 500 °C and at 1000 °C for pressures up to 2.5 bar. Five different devices were fabricated from high-temperature co-fired ceramics (HTCC) and characterized. Alumina green tape sheets were screen printed with platinum paste, micromachined, laminated, and fired. The resulting samples were 21 mm × 19 mm with different thicknesses. An embedded communicator part was integrated with either a passive backing part or with a pressure-sensing element, including an 80 µm thick and 6 mm diameter diaphragm. The study includes measuring thermally and mechanically induced resonance frequency shifts, and thermally induced deformations. For the pressure sensor device, contributions from changes in the relative permittivity and from expanding air trapped in the cavity were extracted. The devices exhibited thermomechanical robustness during heating, regardless of the thickness of the backing. The pressure sensitivity decreased with increasing temperature from 15050 ppm bar−1 at room temperature to 2400 ppm bar−1 at 1000 °C, due to the decreasing pressure difference between the external pressure and the air pressure inside the cavity.
|
|
