| 1. |
- Schael, S., et al.
(författare)
-
Electroweak measurements in electron positron collisions at W-boson-pair energies at LEP
- 2013
-
Ingår i: Physics Reports. - : Elsevier BV. - 0370-1573 .- 1873-6270. ; 532:4, s. 119-244
-
Forskningsöversikt (refereegranskat)abstract
- Electroweak measurements performed with data taken at the electron positron collider LEP at CERN from 1995 to 2000 are reported. The combined data set considered in this report corresponds to a total luminosity of about 3 fb(-1) collected by the four LEP experiments ALEPH, DELPHI, 13 and OPAL, at centre-of-mass energies ranging from 130 GeV to 209 GeV. Combining the published results of the four LEP experiments, the measurements include total and differential cross-sections in photon-pair, fermion-pair and four-fermion production, the latter resulting from both double-resonant WW and ZZ production as well as singly resonant production. Total and differential cross-sections are measured precisely, providing a stringent test of the Standard Model at centre-of-mass energies never explored before in electron positron collisions. Final-state interaction effects in four-fermion production, such as those arising from colour reconnection and Bose Einstein correlations between the two W decay systems arising in WW production, are searched for and upper limits on the strength of possible effects are obtained. The data are used to determine fundamental properties of the W boson and the electroweak theory. Among others, the mass and width of the W boson, m(w) and Gamma(w), the branching fraction of W decays to hadrons, B(W -> had), and the trilinear gauge-boson self-couplings g(1)(Z), K-gamma and lambda(gamma), are determined to be: m(w) = 80.376 +/- 0.033 GeV Gamma(w) = 2.195 +/- 0.083 GeV B(W -> had) = 67.41 +/- 0.27% g(1)(Z) = 0.984(-0.020)(+0.018) K-gamma - 0.982 +/- 0.042 lambda(gamma) = 0.022 +/- 0.019. (C) 2013 Elsevier B.V. All rights reserved.
|
|
| 2. |
- Jaksic, Z., et al.
(författare)
-
Gradient-index infrared metamaterials based on metal-dielectric submicrometer pillar arrays
- 2013
-
Ingår i: 2013 11th International Conference on Telecommunications in Modern Satellite, Cable and Broadcasting Services, TELSIKS 2013. - : IEEE. - 9781479909025 ; , s. 21-24
-
Konferensbidrag (refereegranskat)abstract
- This paper presents the design and microfabrication of a two-dimensional metal-dielectric metamaterial structure based on an array of pillars with submicrometer diameters and heights. The diameters of pillars periodically vary along one axis in a sawtooth fashion and are constant along the other. The electromagnetic field distribution within this graded metamaterial was considered utilizing an accurate analytical approach. The pillar arrays were fabricated in photoresist and subsequently covered with a sputter-deposited aluminum film. Structures were defined by direct laser writing in photoresist film. Controlled overexposure has been applied in order to make pillar features smaller than the nominal resolution of the equipment. The structures were characterized by optical and atomic force microscopy and by angle-dependent Fourier Transform infrared spectroscopy. The produced graded frequency-selective surfaces may be used e.g. in sensing.
|
|
| 3. |
- Jakšić, Z., et al.
(författare)
-
Two-dimensional gradient-index metamaterial with sawtooth profile
- 2013
-
Ingår i: Microwave Review. - 1450-5835. ; 19:2, s. 96-101
-
Tidskriftsartikel (refereegranskat)abstract
- We investigate theoretically and experimentally a binary metal-dielectric metamaterial with a sawtooth profile. The structure consists of a two-dimensional array of pillars with submicrometer diameters. The pillar diameters linearly vary along one axis and are constant along the other. This furnishes a serrated spatial profile of effective refractive index along a single axis. We first present a set of analytical solutions defining the electromagnetic fields in such a structure. Further we give the results of our experimental fabrication of gradient metamaterial with a sawtooth spatial profile. The basic material for pillars was photoresist. Their geometry was defined using direct laser writing. Resist was overexposed in controlled manner in order to obtain pillars with diameters below the nominal resolution of the laser writer. The microfabricated pillars were coated by a sputter-deposited aluminum film. For characterization we utilized optical and atomic force microscopy and angledependent Fourier Transform infrared spectroscopy. We envision the applicability of our graded metasurfaces in transformation optics.
|
|
| 4. |
- Delgado-Ruiz, R. A., et al.
(författare)
-
Implant stability and marginal bone level of microgrooved zirconia dental implants: A 3-month experimental study on dogs
- 2014
-
Ingår i: Vojnosanitetski Pregled. - : National Library of Serbia. - 0042-8450. ; 71:5, s. 451-461
-
Tidskriftsartikel (refereegranskat)abstract
- Background/Aim. The modification of implant surfaces could affect mechanical implant stability as well as dynamics and quality of pen-implant bone healing. The aim of this 3-month experimental study in dogs was to investigate implant stability, marginal bone levels and bone tissue response to zirconia dental implants with two laser-micro-grooved intraosseous surfaces in comparison with nongrooved sandblasted zirconia and sandblasted, high-temperature etched titanium implants. Methods. Implant surface characterization was performed using optical interferometric profilometry and energy dispersive X-ray spectroscopy. A total of 96 implants (4 mm in diameter and 10 mm in length) were inserted randomly in both sides of the lower jaw of 12 Fox Hound dogs divided into groups of 24 each: the control (titanium), the group A (sandblasted zirconia), the group B (sandblasted zirconia plus microgrooved neck) and the group C (sandblasted zirconia plus all microgrooved). All the implants were immediately loaded. Insertion torque, periotest values, radiographic crestal bone level and removal torque were recorded during the 3-month follow-up. Qualitative scanning electon microscope (SEM) analysis of the bone-implant interfaces of each group was performed. Results. Insertion torque values were higher in the group C and control implants (p < 0.05). Periotest values increased in all the periods in proportion to the extent of microgrooving as follows: the group C > the control > the group B > the group A (p < 0.05). Radiographic measurements showed minimal crestal bone loss at 3 months for microgrooved zirconia implants (groups C and B) and control implants compared with the group A implants (p < 0.05). The removal torque values increased with time for all the groups as follows: the group C > the control > the group B > the group A (p < 0.05). SEM showed that implant surfaces of the groups B and C had an extra bone growth inside the microgrooves that corresponded to the shape and direction of the microgrooves. Conclusion. The addition of microgrooves to the entire intraosseous surface of zirconia dental implants enhances primary and secondary implant stability, promotes bone tissue ingrowth and preserves crestal bone levels.
|
|
