| 1. |
- Abel, I, et al.
(författare)
-
Overview of the JET results with the ITER-like wall
- 2013
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 53:10, s. 104002-
-
Tidskriftsartikel (refereegranskat)abstract
- Following the completion in May 2011 of the shutdown for the installation of the beryllium wall and the tungsten divertor, the first set of JET campaigns have addressed the investigation of the retention properties and the development of operational scenarios with the new plasma-facing materials. The large reduction in the carbon content (more than a factor ten) led to a much lower Z(eff) (1.2-1.4) during L- and H-mode plasmas, and radiation during the burn-through phase of the plasma initiation with the consequence that breakdown failures are almost absent. Gas balance experiments have shown that the fuel retention rate with the new wall is substantially reduced with respect to the C wall. The re-establishment of the baseline H-mode and hybrid scenarios compatible with the new wall has required an optimization of the control of metallic impurity sources and heat loads. Stable type-I ELMy H-mode regimes with H-98,H-y2 close to 1 and beta(N) similar to 1.6 have been achieved using gas injection. ELM frequency is a key factor for the control of the metallic impurity accumulation. Pedestal temperatures tend to be lower with the new wall, leading to reduced confinement, but nitrogen seeding restores high pedestal temperatures and confinement. Compared with the carbon wall, major disruptions with the new wall show a lower radiated power and a slower current quench. The higher heat loads on Be wall plasma-facing components due to lower radiation made the routine use of massive gas injection for disruption mitigation essential.
|
|
| 2. |
- Romanelli, F, et al.
(författare)
-
Overview of the JET results
- 2011
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 51:9
-
Tidskriftsartikel (refereegranskat)abstract
- Since the last IAEA Conference JET has been in operation for one year with a programmatic focus on the qualification of ITER operating scenarios, the consolidation of ITER design choices and preparation for plasma operation with the ITER-like wall presently being installed in JET. Good progress has been achieved, including stationary ELMy H-mode operation at 4.5 MA. The high confinement hybrid scenario has been extended to high triangularity, lower ρ*and to pulse lengths comparable to the resistive time. The steady-state scenario has also been extended to lower ρ*and ν*and optimized to simultaneously achieve, under stationary conditions, ITER-like values of all other relevant normalized parameters. A dedicated helium campaign has allowed key aspects of plasma control and H-mode operation for the ITER non-activated phase to be evaluated. Effective sawtooth control by fast ions has been demonstrated with3He minority ICRH, a scenario with negligible minority current drive. Edge localized mode (ELM) control studies using external n = 1 and n = 2 perturbation fields have found a resonance effect in ELM frequency for specific q95values. Complete ELM suppression has, however, not been observed, even with an edge Chirikov parameter larger than 1. Pellet ELM pacing has been demonstrated and the minimum pellet size needed to trigger an ELM has been estimated. For both natural and mitigated ELMs a broadening of the divertor ELM-wetted area with increasing ELM size has been found. In disruption studies with massive gas injection up to 50% of the thermal energy could be radiated before, and 20% during, the thermal quench. Halo currents could be reduced by 60% and, using argon/deuterium and neon/deuterium gas mixtures, runaway electron generation could be avoided. Most objectives of the ITER-like ICRH antenna have been demonstrated; matching with closely packed straps, ELM resilience, scattering matrix arc detection and operation at high power density (6.2 MW m-2) and antenna strap voltages (42 kV). Coupling measurements are in very good agreement with TOPICA modelling. © 2011 IAEA, Vienna.
|
|
| 3. |
- Pegourie, B., et al.
(författare)
-
Deuterium inventory in Tore Supra : Coupled carbon-deuterium balance
- 2013
-
Ingår i: Journal of Nuclear Materials. - : Elsevier BV. - 0022-3115 .- 1873-4820. ; 438:Suppl., s. S120-S125
-
Tidskriftsartikel (refereegranskat)abstract
- This paper presents an analysis of the carbon-deuterium circulation and the resulting balance in Tore Supra over the period 2002-2007. Carbon balance combines the estimation of carbon gross erosion from spectroscopy, net erosion and deposition using confocal microscopy, lock-in thermography and SEM, and a measure of the amount of deposits collected in the vacuum chamber. Fuel retention is determined from post-mortem (PM) analyses and gas balance (GB) measurements. Special attention was paid to the deuterium outgassed during the nights and weekends of the experimental campaign (vessel under vacuum, Plasma Facing Components at 120 degrees C) and during vents (vessel at atmospheric pressure, PFCs at room temperature). It is shown that this outgassing is the main process reconciling the PM and GB estimations of fuel retention, closing the coupled carbon-deuterium balance. In particular, it explains why the deuterium concentration in deposits decreases with increasing depth.
|
|
| 4. |
- Tsitrone, E., et al.
(författare)
-
Multi machine scaling of fuel retention in 4 carbon dominated tokamaks
- 2011
-
Ingår i: Journal of Nuclear Materials. - : Elsevier BV. - 0022-3115 .- 1873-4820. ; 415:1, s. S735-S739
-
Tidskriftsartikel (refereegranskat)abstract
- In order to benchmark predictions for the in vessel tritium inventory in ITER, a survey of fuel retention measured in 4 carbon dominated tokamaks (TEXTOR, ASDEX Upgrade in the 2002-2003 carbon configuration, Tore Supra and JET) was performed, showing retention rates from similar to 1 g D/h in TEXTOR (L mode, limiter machine) up to similar to 6-12 g D/h in AUG (H mode, divertor machine). A simple scaling used for ITER predictions is applied for comparison with experimental values: (1) estimate of wall fluxes, (2) estimate of the gross carbon erosion, (3) estimate of the net erosion/redeposition assuming a redeposition fraction and (4) estimate of the retention rate using D/C ratio scalings. The validity of each step is discussed, showing that this approach yields the right order of magnitude, but tends to underestimate the experimental values unless a high wall flux, a low local redeposition fraction and/or a high D/C ratio are used.
|
|
| 5. |
- Bergsåker, Henric, et al.
(författare)
-
First results from the Be-10 marker experiment in JET with ITER-like wall
- 2014
-
Ingår i: Nuclear Fusion. - : IOP Publishing. - 0029-5515 .- 1741-4326. ; 54:8, s. 082004-
-
Tidskriftsartikel (refereegranskat)abstract
- When the ITER-like wall was installed in JET, one of the 218 Be inner wall guard limiter tiles had been enriched with Be-10 as a bulk isotopic marker. During the shutdown in 2012-2013, a set of tiles were sampled nondestructively to collect material for accelerator mass spectroscopy measurements of Be-10 concentration. The letter shows how the marker experiment was set up, presents first results and compares them to preliminary predictions of marker redistribution, made with the ASCOT numerical code. Finally an outline is shown of what experimental data are likely to become available later and the possibilities for comparison with modelling using the WallDYN, ERO and ASCOT codes are discussed.
|
|
| 6. |
- Hakola, A., et al.
(författare)
-
Global migration of impurities in tokamaks
- 2013
-
Ingår i: Plasma Physics and Controlled Fusion. - : IOP Publishing. - 0741-3335 .- 1361-6587. ; 55:12
-
Tidskriftsartikel (refereegranskat)abstract
- The migration of impurities in tokamaks has been studied with the help of tracer-injection (C-13 and N-15) experiments in JET and ASDEX Upgrade since 2001. We have identified a common pattern for the migrating particles: scrape-off layer flows drive impurities from the low-field side towards the high-field side of the vessel. Migration is also sensitive to the density and magnetic configuration of the plasma, and strong local variations in the resulting deposition patterns require 3D treatment of the migration process. Moreover, re-erosion of the deposited particles has to be taken into account to properly describe the migration process during steady-state operation of the tokamak.
|
|
| 7. |
- Likonen, J., et al.
(författare)
-
Deposition of (13)C tracer in the JET MkII-HD divertor
- 2011
-
Ingår i: Physica Scripta. - : Institute of Physics Publishing (IOPP). - 0031-8949 .- 1402-4896. ; T145, s. 014004-
-
Tidskriftsartikel (refereegranskat)abstract
- Migration of (13)C has been investigated at JET by injecting (13)C-labelled methane at the outer divertor base at the end of the 2009 campaign. The (13)C deposition profiles on carbon fibre composite divertor tiles were measured by secondary ion mass spectrometry and Rutherford backscattering techniques. (13)C was mainly deposited near the puffing location on the outer divertor base tiles. High amounts of (13)C were also found at the outer vertical target: at the bottom of the lower and at the top of the upper plates. Thirty-three percent of puffed (13)CH(4) was instantly pumped out by the divertor cryopump, which is close to the pump duct entrance. Global (13)C transport in the torus was modelled by the EDGE2D/EIRENE and DIVIMP codes, and local (13)C migration in the vicinity of the injection location by the ERO code. The DIVIMP and EDGE2D simulations show strong prompt deposition of (13)C directly adjacent to the injection point as well as in the far scrape-off layer (SOL) along both the inner and outer divertor targets. In addition, the measured (13)C deposition along the outer divertor wall tiles is qualitatively reproduced. However, EDGE2D and DIVIMP do not predict any deposition along the divertor surfaces facing the private plasma on the inner floor tile and inboard of the outer strike point on tile 5. The ERO calculations also indicate that most of the deposition occurs close to the injection location on the vertical face of the LBSRP tile and the horizontal part of tile 6.
|
|
| 8. |
- Likonen, J., et al.
(författare)
-
Deposition of C-13 tracer in the JET MkII-HD divertor
- 2011
-
Ingår i: Journal of Nuclear Materials. - : Elsevier BV. - 0022-3115 .- 1873-4820. ; 415:1, s. S250-S253
-
Tidskriftsartikel (refereegranskat)abstract
- Migration of C-13 has been investigated at JET by puffing (CH4)-C-13 into the outer midplane at the end of the 2007 campaign. The C-13 deposition profile was measured with secondary ion mass spectrometry (SIMS) and Rutherford backscattering (RBS) techniques. C-13 was mainly found on Tile 1 and near the outer strike point (OSP) on Tile 7. The C-13 transport was modelled with the EDGE2D/NIMBUS code. Previous work indicates that migration pathways are: (1) through the main chamber scrape-off layer (SOL), (2) migration through the private flux region (PFR) aided by E x B drifts and (3) neutral migration originating near the strike points. The main contribution of this paper is to further describe the neutral migration.
|
|
| 9. |
- Malaquias, A., et al.
(författare)
-
Development of ITER relevant laser techniques for deposited layer characterisation and tritium inventory
- 2013
-
Ingår i: Journal of Nuclear Materials. - : Elsevier BV. - 0022-3115 .- 1873-4820. ; 438:Suppl., s. S936-S939
-
Tidskriftsartikel (refereegranskat)abstract
- Laser Induced Breakdown Spectroscopy (LIBS) is a potential candidate to monitor the layer composition and fuel retention during and after plasma shots on specific locations of the main chamber and divertor of ITER. This method is being investigated in a cooperative research programme on plasma devices such as TEXTOR, FTU, MAGNUM-PSI and in other various laboratorial experiments. In this paper LIBS results from targets of D-H-rich carbon films and mixed W-Al-C deposits on bulk tungsten substrates are reported (simulating ITER-like deposits with Al as proxy for Be). Two independent methods, one to determine the relative elemental composition and the other the absolute contents of the target based on the experimental LIBS signals are proposed. The results show that LIBS has the capability to provide the relative concentrations of the elements on the deposited layer when the experimental conditions on the targets surface are identical to the calibration samples.
|
|
| 10. |
- Rubel, Marek, et al.
(författare)
-
Comprehensive First Mirror Test for ITER at JET with Carbon Walls
- 2010
-
Ingår i: Proceedings of the23rd IAEA Fusion Energy Conference.
-
Konferensbidrag (refereegranskat)abstract
- Metallic mirrors will be essential components of all optical spectroscopy and imaging systems forplasma diagnosis that will be used on the next-step magnetic fusion experiment, ITER. Any change of the mirrorperformance, in particular reflectivity, will influence the quality and reliability of detected signals. On therequest of the ITER Design Team, a First Mirror Test (FMT) has been carried out at JET during campaigns in2005-2007 and 2008-2009. To date, it has been the most comprehensive test performed with a large number oftest mirrors exposed in an environment containing both carbon and beryllium; the total plasma time (in 2005-2007 period) over 35 h including 27 h of X-point operation. 32 stainless steel and polycrystalline molybdenumflat-front and 45oangled mirrors were installed in separate channels of cassettes on the outer wall and in the MkII HD divertor: inner leg, outer leg and base plate under the load bearing tile. Post exposure studies comprisedreflectivity measurements and surface analyses with microscopy, secondary ion mass spectrometry, ion beamanalysis and energy dispersive X-ray spectroscopy.. The essential results are: (i) on the outer wall highreflectivity (~90%) is maintained for mirrors close to the channel entrance but it is degraded by 30-40 % deeperin the channel (ii) reflectivity loss by 70-90% is measured for mirrors placed in the divertor: outer, inner andbase; (iii) deuterium and carbon are the main elements detected on all mirror surfaces and the presence ofberyllium is also found; (iv) thick deposits show rough columnar structure and thickness is 1-20 μm; (v) bubblelike structures are detected in deposits; (vi) the deposition in channels in the divertor cassettes is pronounced atthe very entrance; (vii) photonic cleaning with laser removes deposits but the surface is damaged by laser pulses.In summary, reflectivity of all tested mirrors is degraded either by erosion with CX neutrals or by the formationof thick deposits. The implications of results obtained for first mirrors in next-step device are discussed andcritical assessment of various methods for in-situ cleaning of mirrors is presented. The conclusion is thatengineering solutions should be developed in order to install shutters or to implement a cassette with mirrors toreplace periodically the degraded ones
|
|
