| 1. |
- Romanelli, F, et al.
(author)
-
Overview of the JET results
- 2011
-
In: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 51:9
-
Journal article (peer-reviewed)abstract
- Since the last IAEA Conference JET has been in operation for one year with a programmatic focus on the qualification of ITER operating scenarios, the consolidation of ITER design choices and preparation for plasma operation with the ITER-like wall presently being installed in JET. Good progress has been achieved, including stationary ELMy H-mode operation at 4.5 MA. The high confinement hybrid scenario has been extended to high triangularity, lower ρ*and to pulse lengths comparable to the resistive time. The steady-state scenario has also been extended to lower ρ*and ν*and optimized to simultaneously achieve, under stationary conditions, ITER-like values of all other relevant normalized parameters. A dedicated helium campaign has allowed key aspects of plasma control and H-mode operation for the ITER non-activated phase to be evaluated. Effective sawtooth control by fast ions has been demonstrated with3He minority ICRH, a scenario with negligible minority current drive. Edge localized mode (ELM) control studies using external n = 1 and n = 2 perturbation fields have found a resonance effect in ELM frequency for specific q95values. Complete ELM suppression has, however, not been observed, even with an edge Chirikov parameter larger than 1. Pellet ELM pacing has been demonstrated and the minimum pellet size needed to trigger an ELM has been estimated. For both natural and mitigated ELMs a broadening of the divertor ELM-wetted area with increasing ELM size has been found. In disruption studies with massive gas injection up to 50% of the thermal energy could be radiated before, and 20% during, the thermal quench. Halo currents could be reduced by 60% and, using argon/deuterium and neon/deuterium gas mixtures, runaway electron generation could be avoided. Most objectives of the ITER-like ICRH antenna have been demonstrated; matching with closely packed straps, ELM resilience, scattering matrix arc detection and operation at high power density (6.2 MW m-2) and antenna strap voltages (42 kV). Coupling measurements are in very good agreement with TOPICA modelling. © 2011 IAEA, Vienna.
|
|
| 2. |
- Abel, I, et al.
(author)
-
Overview of the JET results with the ITER-like wall
- 2013
-
In: Nuclear Fusion. - : IOP Publishing. - 1741-4326 .- 0029-5515. ; 53:10, s. 104002-
-
Journal article (peer-reviewed)abstract
- Following the completion in May 2011 of the shutdown for the installation of the beryllium wall and the tungsten divertor, the first set of JET campaigns have addressed the investigation of the retention properties and the development of operational scenarios with the new plasma-facing materials. The large reduction in the carbon content (more than a factor ten) led to a much lower Z(eff) (1.2-1.4) during L- and H-mode plasmas, and radiation during the burn-through phase of the plasma initiation with the consequence that breakdown failures are almost absent. Gas balance experiments have shown that the fuel retention rate with the new wall is substantially reduced with respect to the C wall. The re-establishment of the baseline H-mode and hybrid scenarios compatible with the new wall has required an optimization of the control of metallic impurity sources and heat loads. Stable type-I ELMy H-mode regimes with H-98,H-y2 close to 1 and beta(N) similar to 1.6 have been achieved using gas injection. ELM frequency is a key factor for the control of the metallic impurity accumulation. Pedestal temperatures tend to be lower with the new wall, leading to reduced confinement, but nitrogen seeding restores high pedestal temperatures and confinement. Compared with the carbon wall, major disruptions with the new wall show a lower radiated power and a slower current quench. The higher heat loads on Be wall plasma-facing components due to lower radiation made the routine use of massive gas injection for disruption mitigation essential.
|
|
| 3. |
|
|
| 4. |
|
|
| 5. |
|
|
| 6. |
|
|
| 7. |
|
|
| 8. |
|
|
| 9. |
|
|
| 10. |
- Gyllenberg, A, et al.
(author)
-
Variability in the CIITA gene interacts with HLA in multiple sclerosis.
- 2014
-
In: Genes and immunity. - Stockholm : Springer Science and Business Media LLC. - 1476-5470 .- 1466-4879. ; 15, s. 162-167
-
Journal article (peer-reviewed)abstract
- The human leukocyte antigen (HLA) is the main genetic determinant of multiple sclerosis (MS) risk. Within the HLA, the class II HLA-DRB1*15:01 allele exerts a disease-promoting effect, whereas the class I HLA-A*02 allele is protective. The CIITA gene is crucial for expression of class II HLA molecules and has previously been found to associate with several autoimmune diseases, including MS and type 1 diabetes. We here performed association analyses with CIITA in 2000 MS cases and up to 6900 controls as well as interaction analysis with HLA. We find that the previously investigated single-nucleotide polymorphism rs4774 is associated with MS risk in cases carrying the HLA-DRB1*15 allele (P=0.01, odds ratio (OR): 1.21, 95% confidence interval (CI): 1.04-1.40) or the HLA-A*02 allele (P=0.01, OR: 1.33, 95% CI: 1.07-1.64) and that these associations are independent of the adjacent confirmed MS susceptibility gene CLEC16A. We also confirm interaction between rs4774 and HLA-DRB1*15:01 such that individuals carrying the risk allele for rs4774 and HLA-DRB1*15:01 have a higher than expected risk for MS. In conclusion, our findings support previous data that variability in the CIITA gene affects MS risk, but also that the effect is modulated by MS-associated HLA haplotypes. These findings further underscore the biological importance of HLA for MS risk.Genes and Immunity advance online publication, 16 January 2014; doi:10.1038/gene.2013.71.
|
|
